Search Documents

Develop a method to evaluate the effectiveness of coal scam fire surface seals so that potential problems may be corrected at an early stage, before the integrity of the surface seal is lost. Background Surface seals are the primary coal seam fire abatement method being used in the western United States. Surface seals smother a fire by denying it oxygen. The seal is usually constructed by placing a mantle of soil, four to ton feet thick, over a coal scam fire area to exclude air from the fire. The soil is compacted to increase effectiveness, and a soil cement may be used to augment the soil. In some cases, burning coal may be excavated and separately smothered or otherwise extinguished in another area; in other cases, a trench maybe excavated and backfilled with incombustible material to isolate a fire. More often, a surface seal is simply applied over and around the entire known burning area. In the 1950's, the Bureau of Mines administered a large program to treat numerous coal seam Fires across the western United States. Methods used in this program were described in Bureau of Mines Information Circular (IC) 7932, dated 1959. More recently however, various coal seam fires have been treated with surface seals under the direction of state Abandoned Mine Land Reclamation authorities. It has frequently taken years to evaluate the effectiveness of surface seals. By the time problems become evident, it has often been too late to take corrective action within the scope of the original abatement project. For this reason, the Bureau of Mines developed a means for tracking temperature trends at coal seam fire projects to obtain a better and earlier handle on the effectiveness of surface seals.

Jan 1, 1991

Provide an inexpensive, remote actuated, stench-gas system which reduces fire warning time to underground work locations. Approach A mine's pager phone hard-wire network is used to release stench gas from pressurized canisters located near working areas. The release is initiated by placing a coded message into a control phone at some central location. How It Works Currently, in most mines, the decision to release a warning stench gas is made by mine management after communication from the mine of a fire or similar potentially dangerous situation. Stench gas is then released into the ventilation air and/or compressed air lines for dissemination throughout the mine. This can result in significant delays in warning time. Often, surface personnel must travel to distant shafts, or other release points, wasting valuable time. Also, the time for ventilation air to circulate from the surface to working locations can be long and the effectiveness of compressed air as a stench transport agent depends on whether the compressed air is being used at the face. The Bureau of Mines, through a contract with MSA Research Corporation, has designed and tested a warning system which avoids these problems. The system consists of multiple, pressurized stench-gas canisters located under-ground in the mine-ventilation network so as to provide quick dissemination of the released stench gas to working areas. Each stench-gas canister is hard-wire connected to a nearby pager phone and from there to a control phone at the surface or at a central in-mine site. In the event of a mine emergency, the canisters are activitated to release stench gas by placing a coded message into the control phone. A low amperage Signal sent from the control phone to the receiver phone closes a relay, which activates a release mechanism on the canister.

Jan 1, 1984

By R. A. Keaens, L. C. IlsLey

For the purpose of this paper a junction box is defined as " a fused switch, inclosed in an explosion-proof compartment, provided with a ready means of connecting or disconnecting a trailing cable without exterior arcing." Junction boxes are intended for use 'at the end of trailing cables and are usually placed outby the last open break through in a coal mine. Where it is not safe to supply current through nips or a trolley, junction boxes suitably spaced along an entry permit tramming and movement of machines with safety, although not with any considerable speed. Junction boxes serve a threefold purpose: (1) They prevent dangerous arcing at the outby end of trailing cables; (2) they afford a safe, practical means of fusing or otherwise protecting the trailing cable; and (3) they provide an efficient means of transmitting power from the power circuit to the trailing cable. The first purpose is the most important from a safety standpoint. Dangerous arcing-that is, arcing capable of igniting gas-frequently takes place where trailing cab1c.s are attached to the power circuit. At either 250 or 500 volts only a very small arc is required to ignite mine gas. The usual method of connecting the trailing cable to the power circuit by cable nips or trolley taps does not make a good electrical connection; hence arcing may be expected at any time. Furthermore, junction boxes eliminate the personal hazard attendant upon the use of trolley taps by removing the possibility of accidental contact with trolley hooks or wire and the liability to injury due to manipulation of the device. In the general scheme of mine ventilation it is assumed that gas will not accumulate where junction boxes are placed, an assumption based on the normal operation of the ventilating system. In many

Jan 1, 1929

By G. G. Morgis, J. J. Forbes

"INTRODUCTION The greatly diversified and increased uses of beryllium and its con& pounds in recent years have focused attention on the health hazards incident thereto. The Bureau of Mines has a fundamental interest in safety and the elimination or reduction of health hazards in the mineral and allied industries, and it recognizes that serious hazards are inherent in the production and use of beryllium and its compounds. This circular presents a review of the literature pertaining to such health hazards but does not describe original research by Bureau personnel. Most of the bibliography has boon either quoted in part or abstracted in an effort to present information in a comprehensive and readable form.In reviewing the literature, differences of opinions wore recognized in the writings of the respective authors, but no attempt was made to evaluate such differences. This presentation was devoted strictly to reporting without editorial comment.SUMMARYAlthough beryllium was known to industry for about 150 years, its toxicity did not present any serious problems in the United States until the advent of World War II, when the increased use of this element and its compounds brought to light several toxicologic reactions occurring primarily in the lungs and skin of workers handling it. The pulmonary effects, characterized as acute pnoumonitis and chronic pulmonary granulomatosis in beryllium workers, are far more serious than the dermatological manifestations.The addition of beryllium to the list of toxic industrial metals has boon so recent that there is still some confusion in the clinical picture. Data on magnitudes of exposure likely to be responsible for the production of disease are not yet adequate. There appears to be no relation between the severity of exposure and the development of cases some of those having had severe exposure have not developed a reaction, whereas those having a slight exposure in some instances have developed a response."

Jul 1, 1950

By John Nagy

Data from experiments and literature on gas and dust explosions in closed vessels are presented to show the effects of the vessel size and shape; the initial pressure, temperature, and turbulence; and the fuel-air ratio and the strength of ignition source on pressure and rate of pressure rise. An attempt is made to correlate some of these parameters with an elementary mathematical model. Analyses of data on 17 vessels--spherical, cubical, cylindrical, and rectilinear in shape--ranging from 0,018 to 905 cubic feet in volume were made. Although the study was initiated to provide information primarily on dust-explosion phenomena, some data were obtained for gas explosions so that the factor of initial turbulence caused by the pneumatic blast used to disperse dust could be evaluated. The mathematical interpretation of the explosion phenomena was in general accord with the experimental data, and correlation was obtained for several factors affecting explosion development. Neither vessel size nor shape affected maximum pressure (when heat loss was neglected). The rate of pres-sure rise decreased as vessel size increased, and the rate was proportional to the ratio of the surface area of the vessel to its volume. Induced initial turbulence markedly increased the rate of pressure rise and slightly increased the maximum pressure. Changes in initial pressure produced proportional changes in maximum pressure and rate of pressure rise. Initial temperature and maximum pressure were inversely related, but initial temperature had little effect on the maximum rate of pressure rise. Comparative experiments showed no appreciable difference in explosion development of gas and dust fuels. The vessels and experimental work are described, and all data are given in tables. The mathematical model will facilitate extrapolation from laboratory to industrial conditions and will allow comparison of results obtained in different laboratories.

Jan 1, 1971

By R. E. Mussler

As part of an overall goal to develop technology that can maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines is evaluating a method for selectively extracting nickel and cobalt from low-grade domestic laterites. The method involves electrowinning to recover the metals in pure form; therefore, preliminary laboratory-scale electrowinning tests were conducted in both a nondiaphragm and a diaphragm cell to determine the effect of variables on energy efficiency under controlled conditions. Electrolytes were generally reagent-grade sulfate solutions that were prepared to simulate electrolyte that could be obtained by stripping nickel-and cobalt-rich solvent extraction reagents. Limited tests were conducted with electrolyte generated from laterite leach solutions. Electrical energy consumption in a nondiaphragm cell was 2.06 kwhr/lb Ni with the cell operated at 50° C, a cell feed of 90 g/l Ni, a pH of 3.5, an extraction of 3.2 g/l, and a cathode current density of 20 amp/ft2. The energy requirement decreased with increasing concentration and temperature, and increased with increasing. extraction and current density. At 50° C, energy consumption in the nondiaphragm cell was 21 pct greater than in the diaphragm cell, but it was only 5 pet greater at 65° C. For this reason and because of overall cost considerations, operation at 65° C with the nondiaphragm cell was preferred. Smooth sheets of cobalt were obtained by electrowinning in a nondiaphragm cell at selected temperatures from 50° to 85° C and with cobalt concentrations from 55 to 87 g/l. The energy consumption (1.48 kwhr/lb) was 22 pet lower with a cobalt concentration of 75 g/l and a cell temperature of 65° C than with a cobalt concentration of 55 g/l and a cell temperature of 50° C.

Jan 1, 1981

The Bureau of Mines believes that all coal mines are potentially gassy; for the purpose of administration in the prevention of explosions and fires, the Bureau recommends: That any coal mine wherein methane or other combustible gas can be detected in amounts as much as 0.27 of 1 percent or more by frequent systematic searches shall be classified as a gassy mine. Permissible methane-indicating detectors such as are given in I.C. 7110 or subsequent lists of Bureau approved methane-indicating detectors, or conventional methods of sampling and analysis of required accuracy may be used. The concentration referred to in the decision is percent by volume.

Jan 1, 1941

In the interest of safety in metal mining, the Bureau of Mines recommends: That underground metal mines be equipped with a main fan in a fireproof housing, located preferably on the surface. The fan installation should be designed to ventilate the mine adequately throughout and to permit prompt reversal of direction of air flow. Many metal mines depend for ventilation upon natural flow of air, assisted by the exhaust from pneumatic drills and by compressed air blown into the workings. Others also ventilate separate headings or sections with fans and blowers. Relatively few have o mechanical ventilating system that controls the coursing of air throughout the mine.

Jan 1, 1939

By W. T. Millar

Graphite in the Suffern deposits near Hillburn, N. Y., consists of flakes ranging in size from fines to one-half inch in diameter. The Bureau of Mines investigated the Suffern deposits in the spring of 1943. Gneiss outcrops were examined, and five trenches excavated and sampled. The graphite is not confined to any definite zone but occurs in small, local pockets. Eleven samples were collected and combined for laboratory tests. Tests by the Bureau of Mines indicate that the graphite ore can be beneficiated by stage crushing, "skin flotation" of coarse flakes, and wet flotation of minus 10-mesh flakes. Over 90, percent of the graphite was recovered.

Jan 1, 1949

By Wilbur I. Duvall

In this report, the Bureau of Mines presents a theoretical solution for the stresses and displacements in an infinite elastic plate containing a circular hole the boundary of which is loaded by applied radial stresses over four separated arcs. The problem solved is a two-dimensional approximation of the stresses and displacements developed by a large tunnel-boring machine anchored in a circular tunnel. Analysis of the solution shows that the tangential tensile stresses induced on the boundary of the circular opening can be minimized in the roof and maximized in the floor of the opening by proper spacing and loading of the four arcs.

Jan 1, 1967

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

The program MFIRE consists of four files MFIRE0 EXE, MFIRE1 EXE, MFIRE2 EXE, and MFIRE BAT The batch file, MFIRE BAT, controls the operation and cooperation of the three executable pro¬gram files and the output Networks of up to 500 air¬ways and 350 junctions can be modeled in the PC version of MFIRE Larger data sets can be accommodated by increasing array dimensions and compiling the program again. Input for MFIRE is in the form of a data file The data file contains fines of numerical data describing the physical mine, the ventilation parameters present, the fans, and the proposed thermal or mechanical disturbances

Jan 1, 1990

By T. Brady, R. Langston, J. C. Johnson, H. Kirsten

An experiment is described in which instrumented rock bolts were used to measure strain in the rock mass during drift development at the Stillwater Mine, Nye, Montana, USA. Two strain-gauged rock bolts were grouted into the middle of the rib next to the face. The drift was excavated in three advances, each one-half drift wide. Strains were recorded hourly by a data logger. Results show that the average change in axial bolt strain for the first and second advance was about the same and that there was almost no change in strain after the third advance. Bending strain was observed 19 cm from the head of the bolt.

By R. Larry Grayson, Douglas F. Scott

Data on health-related illnesses and disease in the mining industry are scarce, and information on rates and costs is not readily available. Substantial amounts of research are being directed to addressing these issues, including work at the National Institute for Occupational Safety and Health’s (NIOSH) mining health and safety laboratories in Spokane and Pitts-burgh. This paper briefly discusses the current status of some miner health-related issues, including those involving coal dust, silica dust, diesel particulate matter, asbestos, noise, lead, welding fumes, and skin disorders, as well as research and other activities aimed at protecting miners from occupational illnesses and disease.

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

C 2 Complete Hoisting Systems A Above Ground Installations A total of seven companies were identified who supply complete emergency escape hoist units for above ground installations The units have been designed predominately to meet the needs of coal mine operators to satisfy the requirements of the Coal Mine Health and Safety Act of 1969. The seven companies are as follows 1 Dover Conveyor and Equipment Co. 2. Coeur d' Alenes Co. 3. Connellsville Corp. 4. Scott Midland 5. W W Williams Co. 6. Equipment Corporation of America 7. Timberland Ellicott Table VIII contains detailed specifications and price information on each of these units. The units have a number of similarities

Jan 1, 1976

By Mathew P. Oommen, Jeffrey L. Kohler

Computer-aided loadflow and fault analyses of mine power systems are routinely conducted to ascertain system performance and also to provide information to assist in the protection and coordination of these systems. Three-winding transformers are frequently encountered in mining applications, typically at continuous miner and longwall sections where there exists a need for dual utilization voltages. These transformers are often modeled as a three-bus system neglecting the secondary to tertiary winding impedance and the effect of base changes. This paper analyzes the impact of more accurate transformer models on voltages and fault currents which are realized from loadflow and fault studies of mine power systems.

Work on this program was supervised by R. C. Streeter, Project Scientist, R. K. Young, Principal Investigator, and R. A Glenn, Project Director Technicians involved in the conduct of the experimental work were J R. Allender, D. R. Wolber, G. L Maclay, and A. C Rupert The assistance of Project Scientists C. T. Ford in the electrokinetic studies, and R. R. Care in the spectrographic analyses, is also acknowl- edged. The valued advice and guidance during the course of this program from R. D Hill, EPA Project Officer, and Dr. D R. Maneval, Director of Planning and Coal Research for the Department of Environmental Resources, Commonwealth of Pennsylvania, is sincerely appreciated.

Jan 1, 1971

By Richard G. Geyer

One aspect of a program to improve the chances of survival following coal mine disasters is the development of a communications system which will allow surviving miners to make their circumstances known to rescue teams. Various communications techniques can be considered, including electromagnetic systems, acoustic systems, and hybrid systems. The electromagnetic and acoustic systems would be independent of existing mine communications systems and set up specifically for use in emergencies. Hybrid systems might use a short emergency link to existing telephone systems in the mine. Many variations are technically possible, and the primary task is in evaluating the relative merits of each, so that the most workable system can be selected.

Jan 1, 1973

By J. C. Franklin

An experiment was conducted by the U.S. Bureau of Mines and the Canada Centre for Mineral and Energy Technology (CANMET) to measure the emanation rate of radon from cemented unclassified mill tailings in two dewatered stopes of a uranium mine at Elliot Lake, Ontario, Canada. The radon was monitored upstream and downstream and in both stopes to determine the concentration in the stopes and the amount exhausted from both stopes. The emanation rate was determined to be 0.55 pCi/cm2 sec-1 from the mill tailings, which is approximately 1,000 times higher than the average flux in the mine before backfilling.

Jan 1, 1982

By Gordon L. Kinney

Following a year of great uncertainty, the political situation in Bangladesh improved during 1976. The major problem for Bangladesh remained the high birth rate and crowded conditions. Bangladesh had the highest population density of any agrarian country--over 80 million people in a land area of 144,000 square kilometers, 65% of which is considered arable. The Government, with considerable foreign assistance, was actively encouraging voluntary family planning, and set a growth rate target of 2% per year or less. However, even if the growth rate was reduced to the target level immediately, the population of Bangladesh would nevertheless nearly double within 20 years.

Jan 1, 1980

Cement kiln dust (CKD) is a waste product generated at the rate of 4 to 12 million tons per year in the United States. The dust has considerable resource potential as a neutralizer for coal mine waste effluents and as a lime substitute in the agriculture and construction industries. However, little information has been published on the composition and characteristics of CKD, and a concern arose over the potential environmental effects of the waste when an analysis of a single sample from West Germany revealed lead and zinc concentrations of 5,620 µg/g and 16,200 µg/g, respectively. To assess the hazardous waste potential of CKD,

Jan 1, 1983