Search Documents

By Alla D. Mah

Thermodynamic calculations for antimony and its compounds have been hampered by the lack of adequate basic thermal data; much work rains even to fill the more important gaps. This paper supplies heat and free energy of formation values at 298.15° K, for the sesquioxide and tetroxide, based upon new measurements conducted by the Bureau of Mines. The heats of formation were obtained by combustion (bomb) calorimetry, and the free energies of formation were obtained by combination of heat and entropy data. The new values are believed to substantially improve the accuracy of thermodynsunic considerations involving these oxides.

Jan 1, 1962

By C. H. Herty

Intensive work on the deoxidation of steel with manganese-silicon alloys by the U. S. Bureau of Mines has shown that the use of those alloys, which may be produced from our domestic manganese ores, would decrease the ferromanganese requirements of a very large tone of our steel by from 60 to 30 per cent and in some cases by 100 per cent. The open-hearth heats made with these alloys have been of excellent quality. The tonnage of our ferro-grade ores which has been made available by the bureau's ore-dressing studies, combined with the ,products resulting from such processes as those developed by the bureau and by Bradley for Cuyuna ores, should easily fill our reduced ferromanganese requirements Then manganese-silicon alloys and ordinary spiegel are used in the way described in this report. There are no technical difficulties in the application of this practice, and any difficulties involved in its wide and immediate application would only be those arising from habituated ideas of the necessity of ferromangenese. General acceptance of this practice and development of the available sources of domestic ferro-grade material by already proven processes should make this country independent of foreign ores.

Jan 1, 1931

By Jami M. Girard, Ed Mchugh

Slope stability accidents are one of the leading causes of fatalities at U.S. surface mining operations. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is currently conducting research to reduce the fatalities associated with slope failures. The purpose of this paper to discuss some of this research and to present potential new technologies for slope monitoring and design. The paper also briefly discusses various warning signs of slope instability, introduces the most common slope monitoring methods, describes the limitations of various slope monitoring systems, and presents some field results using some of this new technology.

By Jr. Harty

Intensive work on the deoxidation of steel with manganese-silicon alloys by the U. S. Bureau of Mines has shown that the use of those alloys, which may be produced from our domestic manganese ores, would decrease the ferromanganese requirements of a very large tonnage of our steel by from 60 to 80 per cent and in some cases by 100 per cent. The open-hearth heats made with these alloys have been of excellent quality. The tonnage of our ferro-grade ores Which has been made available by the bureau's ore-dressing studies, combined with the products resulting from such processes as those developed by the bureau and by Bradley for Cuyuna ores, should easily fill our reduced ferromanganese requirements when manganese-silicon alloys and ordinary Spiegel are used in the way described in this report. There are no technical difficulties in the application of this practice, and any difficulties involved in its wide and immediate application would only be those arising from habituated ideas of the necessity of ferromanganese. General acceptance of this practice and development of the available sources of domestic ferro-grade material by already proven processes should make this country independent of foreign ores. This paper resents the results of work done under a cooperative agreement between the Pittsburgh Experiment Station of the United States Bureau of Mines and the Carnegie Institute of Technology, the Metallurgical Advisory Board, and the University of Pittsburgh, Pittsburgh, Pa.; between the Mississippi Valley Experiment Station of the United States Bureau of Mines and the Missouri School of Mines and Metallurgy, Rolla, Mo.; between the North Central Experiment Station of the United States Bureau of Mines and the University of Minnesota, Minneapolis, Minn.; and between the Rare and Precious Metals Experiment Station of the United States Bureau of Mines and the University of Nevada, Reno, Nev.

Jan 1, 1931

By R. L. Crosby

The effect of indium on the solid solubility of calcium and of silicon in magnesium was studied using metallographic, X-ray diffraction, and electrical resistivity techniques. The addition of 2 weight-percent or more of indium reduced the solid solubility of calcium in magnesium by forming a compound containing indium and calcium. Indium additions have no perceptible effect on the solid solubility of silicon in magnesium.

Jan 1, 1963

By Arthur S. Swanson

The DuBois fluorite property in the southwestern part of Hardin County, Ill., has been active intermittently since 1904 and has produced an estimated total of 1,000 to 2,000 tons. The persistence of the vein and the stratigraphy suggested extensions of the ore body formerly mined. The Bureau of Mines investigated the property by core drilling early in 1944. Four holes were bored which totaled 1,106 feet and extended along a strike length of 1,150 feet. The data obtained in the course of the investigation are presented in this report.

Jan 1, 1948

By Bernard Porter

The rate of the heterogeneous reaction between high-purity uranium metal and uranium tetrafluoride in molten lithium fluoride was measured. The apparent heat of activation for the reaction is 16.91 kilocalories per mole of UF4. A surface-controlled mechanism is suggested in which UF4 is adsorbed on the uranium metal surface. Additional UF4 reacts with the adsorbed species and the metal site to form an activated complex that decomposes to the product UF3. The reaction is an important source of metal loss in the electrowinning of uranium metal.

Jan 1, 1966

By W. W. Weller

Heat-capacity measurements of sodium dimolybdate (Na2Mo207) and sodium ditungstate (Na2W207) were conducted over the temperature range from 51° to 298° K. The entropies of the two compounds at 298.15° K were calculated from the heat-capacity values and were used, in conjunction with other entropy data, to evaluate the entropies of formation of the compounds from their constituent elements and oxides.

Jan 1, 1963

By Sathit Tandanand

This report presents a Bureau of Mines study on the time-dependent behavior of coal measure rocks for future implementation in stability analysis and safety evaluation of in-mine rock structures. This initial study focused on moisture adsorption rate and strength degradation of shales in Pennsylvanian coal-bearing strata in the Illinois Basin. A reaction of clay minerals in Illinois shales with atmospheric water vapor was hypothesized as the adsorption and strength degradation mechanism. Part of energy exchange between shales and the environment was attributed to a free energy controlled by pore pressure of the rock and partial pressure in the environment. The relationships between adsorption versus time and strength degradation versus moisture content were derived and correlated with the experimental data. Partial saturation at various levels of relative humidity occurs within approximately 2 weeks at room temperature. The strength of shales tested decreases linearly with increasing moisture content. When the moisture exceeds 7 pct of the dry weight, these Illinois shales become unstable. To this end, the moisture content is a good predictor of rock strength for shales.

Jan 1, 1987

Although early Spanish settlers used coal several centuries ago, significant commercial coal mining in New Mexico began in 1861, when the U.S. Army opened a mine to supply Fort Craig. Since then, coal from the state has been used to fuel railroads, lead and copper smelters, and other local industry. In recent years, lower-cost strip mining methods and an increased demand for coal by electric utilities in the Southwest have caused an increase in New Mexico coal production. The coal-bearing regions of New Mexico underlie about 25,000 square miles or20.6 percent of the total area of the state. However, the majority of coal-bearing regions lie under Indian lands that are regulated by the Office of Surface Mining (see Navajo and Hopi data on pages 72-75). Today, most of the coal produced in New Mexico comes from the San Juan Basin in the northwest part of the state and the Raton Area in the north central part. New Mexico's reserves are estimated to be 4.6 billion tons, about one percent of the national reserve. New Mexico's permanent regulatory program was conditionally approved December 3 1, 1980. Its Abandoned Mine Lands Program was approved July 17,198 1.

Jan 1, 1992

By D. Harrington

"While distribution of air currents to working faces is a necessity in coal mines, especially those having explosive gas, advancing faces in metal mines rarely have circulating air other than the ordinarily inadequate amount supplied through the compressed air system. Even where comparatively large quantities of air pass through main mine shafts and levels. whether the circulation is actuated by fans or by natural ventilation, only occasionally can a metal mine be found where any considerable percentage of the ""blind ends"" has circulating air of sufficient velocity to be measured by an anemometer or even be discerned by deflection of flame of candle, or of acetylene lamp; and unfortunately these ""blind ends"" include nearly all of the places from which rock is taken.During several years study of metal-mine ventilation in various mining districts of the United States, it has been found that in some mines many of the workers in ""blind ends"" practically continually breathe air with 0.02 to 0.04 per cent of CO gas from unremoved fumes from explosives; in other mines CO2 chiefly from timber decay and breathing of men, is so high that a candle will not burn though usually the acetylene lamp will, hence oxygen is below 17 per cent but above 12 per cent; in some regions CO2 from strata fills the entire mine forcing cessation of work; in other mines in dead ends, gases such as nitrogen, H2S, SO2, etc., are found under some conditions. In many regions with hot rock or water (especially in deep workings) men in blind ends must work with little or no circulation, in air above SO degrees F. and even above 90 degrees, relative humidity only too frequently being around 100 per cent; in other regions workers in blind ends in practically ""dead"" air must continually breathe enormous quantities of finely divided rock dusts. All of the above conditions are decidedly harmful to health and prevent the worker from delivering anything approaching an adequate quantity of work, and in addition, some of these conditions have direct or indirect effect in bringing about definite increase of accidents; all of the above mentioned bad conditions in ""blind ends"" in metal mines as well as their ill effects, are remediable by providing at those places adequate quantities of fresh circulating air."

Nov 1, 1923

By G. R. Palmer

The Bureau of mines evaluated the elution of uranyl carbonate from a strong base resin with a mixed carbonate eluant in a fluidized system. The system consisted of a multiple-compartment ion-exchange (MCIX) elution column with a continuous flow of solution, except for short periods when the resin increments were withdrawn. The exchange of uranyl carbonate from the mill-loaded strong base resin with an eluant composed of 1.0 [M] NaaCOs plus 1.0 [M] NH4HCO3 was studied. The effects of solution flow rate, aqueous-to-resin flow ratio, column diameter, compartment height, initial resin concentration, and column length were examined. The experimental data indicate that for the eluant examined, a resin residence time of 240 minutes is necessary to attain 90-percent elution efficiency. Also provided is a technique for sizing an elution MCIX column form pilot plant experimental data.

Jan 1, 1979

By L. C. IlsLey

Minin,g Qr col-cu.ttint till:I chines are 1?;\i9ng the _m9t wideiy .used de1sses ()f mining equipment.· These 1T:.i:1Chines ,.--re practicaily t-tl\·operc1_ted eiyher_by compressed .iir or by electric. ·motors. According to &.ta• compiled _ from the 122. issue COAL CATALOG\JE. OJMEINED WITH; OOAL "FIELD 'pf!:fC'TOTl1, bf 7,088. mnes from which reports were obttiined there -are 3895 mines that u.se coal-cutting eql;lipmen:ts,, 'f'hi report lists 20,031: r.ct:lchines, 17,&75 being operated by·elct:i.c.m<;>_tors··:r;id :the remtiinder by compressed i.r motors,· ,-. · ', .. . · .. ··, .. _ ,· .,, .. .. . . . . . : ; "'l t:: On tl.Ccou-nt .. of the wide· use of coc:11-cutting -.:i"cliine_- any Stat!;ls have issued regulationa as "to their operation dnd be to safety precautions that.should be observed J especially in gaseous mines.

Oct 1, 1922

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Air Moving and Conditioning Association, Fan Application Manual Part 1, Fans and Systems, AMCA Publication 201, 1976a. Air Moving and Conditioning Association, Fan Application Manual Part 2, Troubleshooting, AMCA Publication 202, 1976b. Air Moving and Conditioning Association, Fan Application Manual Part 3, Field Performance Measurements, AMCA Publication 203, 1976c. Air Moving and Conditioning Association, Directory of Products Licensed to Bear the AMCA Certified Ratings Seal, Edition 27, August 1, 1975. Allan, A. L., Hollwey, J. R., and Maynes, J. H. B., Practical Field Surveying and Computations, American Elsevier Publishing Co., Inc., New York, 1968. American Society of Heating Refrigeration and Air Conditioning Engineers Std. 51-75, Air Moving and Conditioning Association Standard 210¬74, Laboratory Methods of Testing Fans for Rating. Anderson, T. C., and Nugent, J. W., "Mine Ventilation Pressure Differentials with a Programmable Hand Calculator," MESA Informational Report 1050, 1977. Atkinson, J. J., "On the Theory of the Ventilation of Mines," Trans. N. E. Inst., Vol. 3, 1854, pp. 118. Barnes, E. L. S., "Mine Ventilation Network Analysis," International Mine Ventilation Congress, Marshalltown, S. Africa, Sept., 1975. Boshkov, S, and Amontree, B., "How Operator Proximity Affects Anemometer Readings," Coal Age, Vol. 55, No. 5, 1950, pp. 85-56. Boshkov, S., and Wane, M. T., "Errors in Underground Air Measurements," Mining Engineering, Vol. 11, No. 7, November, 1955, pp. 1047-1053. Briggs, H., "The Underground Leakage of Air, Investigation of the Porosity Coefficient," Transaction of the Institution of Mining Engineers, Vol. 82, pp. 111-121. Brown, J. R., and Hinsley, F. B., "The Flow of Air in Bends and Straight Airways," Transaction of the Institution of Mining Engineers, Vol. 116, July, 1957, pp. 845-867. Burrows, J., "Measurement of Fan Pressures," Journal of the Mine Ventila¬tion Society of South Africa, Volume 27, No. 4, April 1974, pp. 57-63.

Jan 1, 1977

By Fredrick L. Johnson

No mineral resources were delineated during our investigation of the Antelope Wilderness Study Area (WSA). Only a few claims have been located in the area and only four workings were found. There has been, however, considerable exploration and mining activity in and near the south end of the study area. The Morey mining district, just southeast of the WSA, produced silver, and lesser amounts of gold and lead, sporadically from the mid-1860&apos;s through the mid-1960&apos;s. Long Lac Mineral Exploration (Texas), Inc. is actively exploring a large block of claims for hot-spring type, low-grade, large-tonnage gold deposits. Their claim block extends into the study area. The WSA, located midway between Tonopah and Eureka, encompasses approximately 87,400 acres. It is underlain by Tertiary rhyolitic and latitic volcanic rocks and by Paleozoic sedimentary rocks. At least three areas in the Paleozoic rocks have many of the favorable criterion for hot-spring type gold deposits; they have been faulted, silicified, brecciated, and hydrothermally altered, and have anomalous concentrations of precious metals and pathfinder elements. With additional exploration in the south part of the Antelope WSA, gold resources may be discovered.

Jan 1, 1986

Minimize drilling time in roof bolting. Approach The Bureau of Mines conducted a survey of 34 roof bolting machines used in underground coal mines. Results of the survey indicated that drilling time, bit cost, and respirable dust concentrations and be reduced by using the appropriate bits for drilling, To evaluate bits currently used and to find optimum cutting parameters needed to minimize drilling time, the Bureau tested two bits commonly used in most underground mines on both wet and dry systems. These are the dusthog* and shank type. The dusthog has dust ports in the bit body to remove cuttings. With shank bits, holes in the drill steel do this. Cost of each type is roughly equal. Bolters with dry vacuum systems were tested in the laboratory first. The lab tests were verified by underground tests in several mines. Bolters with low-pressure wet drilling systems were also tested under-ground. Tests concentrated on the effect of rpm, water and airflow rates, heating, wear, bit design and bit type. Lab Results -Dry Drilling Holes were drilled during the laboratory tests using a production model bolter drilling 45-inch-deep holes into mixtures of lime stone and sandstone aggregate. All tests started with new shank and dusthog type bits at 225 and 450 rpm. Thrust was about 6,000 lbs in all tests. Each bit was tested at two airflows, 15 and 25 cfm, airflows which are typical on operating roof bolter bits. Eleven styles of bits were evaluated. On the average, dusthog bits drilled 25% faster than shank types and were always cooler after drilling. The effect of RPM was tested with 5 different bit types. When bit rpm was increased from 300 to 400, drilling rates doubled. With used, well-worn bits drilling time and final bit temperature were more than doubled.

Jan 1, 1986

By L. C. IlsLey

Permissible blasting units are approved with the understanding that if actively marketed they will be listed as permissible so that all interested in such safety equipment may know what is available. The last detailed lint of permissible units was published as Technical Paper 4294/. All of the blasting units of that list have become obsolete or have boon modified as covered by extensions of the original approvals.

Jan 1, 1941

Develop a curved ray geotomographic program with constraints to counteract non-uniqueness in order to improve the reliability of seismic tomographic imaging of geological structure in mining regions. Background Seismic tomography provides a two-dimensional image (tomographic reconstruction) of the distribution of the seismic velocity in geologic structures using measured travel times of seismic waves crossing the area. It can provide a more complete representation of features be¬tween boreholes than other crosshole processing methods that measure only average properties or borehole logging methods that measure properties only near each borehole. Seismic tomography has many mining applications. They include locating geologic structures of contrasting seismic velocity, detecting fractured regions where the seismic velocity is low, and monitoring solution injected above the water table where the increase in saturation increases the seismic velocity. Thus, tomographic imaging techniques show great promise for detecting and locating geologic hazards that affect the productivity, safety, and environment of mining operations.

Jan 1, 1992

By Jeffrey M. Listak

The Respiratory Hazards Control Branch of NIOSH routinely conducts laboratory and mine-site evaluations of dust control technologies. Gravimetric and instantaneous dust sampling instruments are used in these evaluations to measure and document dust levels to determine worker exposure. The Thermo personal DataRam (pDR) is an instantaneous sampler that uses light-scattering technology to provide relative measures of airborne respirable dust. The pDR can be used in active and passive modes to measure respirable dust levels. Tests were conducted to evaluate the sampling performance of active and passive pDR operation relative to each other and. against a gravimetric sampler (the accepted standard for respirable dust measurement). The purpose of the test was to determine if the pDR can be used effectively in the passive mode in higher velocity airflows (up to 5.1 m/s (1000 fpm)). Studies of the pDRs in both modes of operation were conducted in a controlled laboratory environment and in field situations. Dust measurements using pDR units in both modes of operation were recorded in ve¬locities ranging from 1.0 to 5.1 m/s (200 to 1000 fpm). Tests were conducted in ambi¬ent air and in air with the addition of moisture. Results show that, although the units measure different concentrations in their respective modes of operation as compared to a gravimetric sample, the relative readings can be corrected to yield accurate dust measurements.

Jan 1, 2007

Provide an economic alternative to drill-blast excavation with the same ability to excavate openings of varied orientation, shape, and size. Approach Develop an efficient, adaptable, mechanical excavation machine that produces unconfined tensile failure in rock. How It Works A drill-split fragmentation machine that combines a drill and a unique splitter has been developed. The drill and splitter are mounted on a carriage that positions the splitter in a hole immediately after it is made by the drill. The splitter creates force loads that cause the rock to fragment, and the process is repeated for excavation. The unique splitter applies both radial and axial loads to the rock mass, which produces an excavation action comparable to pulling a plug. This excavation action distinguishes the radial-axial splitter from typical demolition splitters, which require a free surface parallel to the axis of the splitter toward which to break rock.

Jan 1, 1989