Search Documents

By S. L. Windes

"INTRODUCTION For a number of years the bureau of Mines has been engaged in the detection, recording and interpretation of earth- and air-transmitted disturbances, man-made and natural, related to mining operations. For the measure¬ment of such disturbances, special equipment was developed (1, 2, 3, 4, 8) 3/ and results of the measurements have been reported (5, 6; 7,9).In general, the ranges of amplitude end frequency of vibration encountered and recorded in the earth-transmitted disturbances were 0.00005 to 0.1 inch and 5 to 5,000 cycles per second; in the air-transmitted disturbances, pressures ranging from 0.001 to 100 pounds per square inch and 0 to 20,000 cycles per second were recorded.One characteristic of the earlier tests was that either the arrival time of the disturbance to be recorded was predictable or the recording speed was slow enough so that the record covered extended periods of time (for example, 4 hours). As the investigations continued, it became apparent that a recording device was required that would respond to transient vibrations arriving at indeterminate times and at the same time provide a permanent record of displacement or acceleration versus time on a scale that would permit the analysis of waves having frequency components up to 10,000 cycles per second. A film or paper speed of 720 inches per second was found to be adequate, as this provides approximately 3/4 inch of record for each 0.001 second."

Dec 1, 1947

By F. N. Kissell, H. K. Sacks

This study examines the accuracy of area sampling for measuring the dust exposure of mining machine operators in coal mines. The specific objective of this research was to find locations where an area sampler might work better than earlier studies have indicated. The results show that fixed-location area sampling cannot accurately predict the dust exposure of a machine operator, even when the best fixed location is sought, the fixed location is quite close to the operator and the bias due to the dust concentration gradient is corrected. Industrial hygienists have known for many years that area sampling is unsuitable for measuring air contaminant exposures in the workplace. Near contaminant sources, the dilution air and the contaminants are not evenly mixed. Therefore, when workers are near contaminant sources, exposure measurements must be taken from the worker's breathing zone to be accurate

By Steven J. Page

The increasing concern for dust control in metal and nonmetal mining prompted the Bureau of Mines to investigate the dust suppression technique of applying foam to face drilling and crushing operations in a gypsum mine. Previous attempts to achieve effective dust control on face drills using other techniques, such as dry collection and boom-mounted external water sprays, have not been successful. The largest problem encountered when using these techniques has been the lack of sustained effective dust capture at the face. Results for two faces studied show that injection of the foam through the drill steel provided an average dust reduction of 95 pct. However, the use of foam on the crusher provided no dust reduction at the operator's position (because of good local ventilation) and a 27-pct average dust reduction for two feeders at a location midway between the operator's position and the crusher. The conclusions obtained from this study are that (1) foam can be an extremely effective dust control technique when used on localized dust sources such as dust generated within a blasthole during drilling, and (2) foam is only marginally effective as a dust control technique when used on nonlocalized dust sources such as dust generated during the feeder-and-crusher operation.

Jan 1, 1981

By G. W. Jones, R. E. Kennedy

A simple , quick, and relatively accurate device is needed for determining the presence of very small concentrations of organic halide gases in various atmospheres . Such a device would enable safety engineers , health officials , and others to discover quickly the presence of these gases in a suspected atmosphere and thus be able to apply protective measures promptly. This detector should prove useful in detecting leakage of halide gases from refrigerating and air - conditioning systems and in determining the presence of halide solvents in the atmosphere of dry - cleaning and degreasing establishments where organic halide solvents are used . Virtually all poison war gases are halide compounds . Because of the high toxicity of these gases , even in very low concentrations , a detector having the proper sensitivity should be useful in civilian defense for determining when atmospheres are relatively free of poison gases .

Apr 1, 1943

As a basis for recommendation and for instruction of bureau engineers the considered opinion of the bureau is expressed in "decisions" of its Mine Safety Board, approved by the Director. Ten of these decisions were discussed, in Information Circular 6091.3 Decision No. 11, approved by Scott Turner, Director, on February 28, 1929, is as follows: "In the interest of safety, the Bureau of Mines, Department of. Commerce, recommends that in coal mines, haulage and (or) hoisting be kept in intake air as far as possible." As in the case of previous mine-safety decisions, the subject matter covered by this decision has frequently come to the attention of the Bureau of Mines through the reports of its mining engineers on explosion disasters and in accident-hazard investigations.

Jan 1, 1929

By Dennis R. Dolinar

Screen material in the form of welded wire mesh and geogrids are used in underground coal mines to prevent the fall of small pieces of rock from the roof between roof bolts. Further, if the screen is installed during the production cycle, roof fall injuries can be reduced significantly. Therefore, the National Institute for Occupational Safety and Health (NIOSH), because of the safety implications, conducted an evaluation of screen materials commonly used in U.S. coal mines to determine their support characteristics and identify the parameters that could affect their performance with respect to controlling the fall of rock from the roof surface. To evaluate the load and stiffness characteristics of the screen, a test frame was designed and installed in the Mine Roof Simulator (MRS) at the NIOSH Pittsburgh Research Laboratory (PRL). With this test set up, the screen is bolted at four corners of the frame and a center load is applied. The test set up allows for up to 20 in of screen deflection while the load and screen defection are continuously recorded. A series of tests were conducted to evaluate the effects of various parameters such as bolt tension, the type of load bearing surface and the size of bearing plates on welded screen performance. The most common screen material used in U. S. coal mines is an 8-gauge wire welded in a 4-by-4-in spacing or aperture. The peak screen load was normally limited by wire breakage. The conditions at the bearing plate influence the nature of the wire breakage. However, the screen stiffness was controlled by slippage at the bearing plates, and by weld and wire failure. The size of the bearing plate had a significant effect on the performance of the welded screen. Therefore, the design capacity of the 8-gauge screen is evaluated based on plate size. For a 6-by-6-in bearing plate the average peak load is 2,900 lb with a stiffness of 250 lb/in. For an 8-by-8-in bearing plate, the average peak load is 4,500 lb with a stiffness of 430 lb/in. These test results are based on a 4-by-4-ft bolt spacing. A geogrid mesh was also tested.

Investigate and demonstrate the possible use of low-density (45-lb/ft3) foam concrete for sealing abandoned mine openings. Although foam concrete has been used in the construction and geotechnical industries for some decades, it has not previously been used in abandoned mint shaft reclamation. Approach A structurally engineered permanent mine seal for an abandoned coal mine shaft, using low-density foam concrete and other appropriate structural materials, was designed by the Bureau and installed at a field site, the No. 22 Shall in Logan County, West Virginia. The field work was conducted by a private contractor under the supervision of the West Virginia AML Section (WV AML). The No. 22 Shaft is situated immediately adjacent to a frequently traveled county road. A few feet away from the shaft is a branch of Pine Creek. On the other side of the road is a railroad line that serves an active mining operation located several miles away. The shaft measures 9.5 by 9 feet in cross section and is about 300 feet deep. It was used at one time as a dewatering shaft and still contains two large-diameter dewatering pipes with steel drive shafts inside them. Before the beginning of the reclamation, the shaft included a concrete cap a few inches thick, with a 4 - by 5-foot access opening covered by a steel grate. The interior of the shaft was quite humid, and considerable flow of water at the bottom of the shaft could clearly be heard from the surface. Methane tests were conducted that showed the shaft to be clear of this gas.

Jan 1, 1992

By T. W. Beck

The National Institute for Occupational Safety and Health (NIOSH) conducratory and field tests to evaluate the effectiveness of dust collector bags for reducing dust liberation and operator exposure from a roof bolter’s dust collection system. The laboratory tests evaluated the bag’s effectiveness to contain dust and the effect on canister filter loading in both a bag and bagless condition. The dust emissions from the collector’s exhaust were also measured in each condition during laboratory testing and show that nearly 100% of the test dust fed into the collector was captured by the dust bags. Loading and pressure drop on the dust collector’s canister filter is greatly decreased when using the bags, enabling longer periods of drilling without filter removal/cleaning. The field results showed that, even though dust standards were met, respirable dust in exhausted emissions was reduced around the bolter. Laboratory and field results show that benefits from use of the bags are realized in all areas of operator exposure.

By S. D. Maksimovic

The Bureau of Mines evaluated the hydraulic stimulation of a gob-degasification borehole to determine if this procedure would aid in degasifying a longwall panel. The stimulated borehole did not degasify the longwall panel as expected either before or after mining of the panel started. It reduced the underground methane emission only 11 pct, considerably less than the reductions effected by two unstimulated boreholes in the same panel. Some probable reasons for the reduced methane flow from the hydraulically stimulated borehole are very low reservoir gas pressure, location of hydraulically stimulated zones within the grouted casing, a casing break caused by lateral shifting, possible vertical movement of rock strata during caving, grouting of a 4-inch pipe blocking three stimulated zones, plasticity of shales, and possible hole damage by swelling of water-sensitive minerals. The borehole was also located between two second-mined areas, which may have allowed partial degasification of the overburden and the coalbed in advance of mining. Finally, a period of 3 months is probably not long enough for the borehole to degasify the overburden before mining.

Jan 1, 1977

Determine the extent to which remote-sensing techniques, primarily lineament analysis, can be used to identify geologic structures that may affect the location and migration of subsidence over abandoned underground coal mines in the Colorado Springs, CO, area. Compile data using a geographic information system (GIS) to allow efficient and reproducible comparisons and analyses. Background The basis for evaluating abandoned mine land (AML) sites with remote-sensing techniques comes from past and ongoing Bureau ground control research using remote-sensing data to identify potential hazards caused by geologic structures (faults, joints, etc.) above active underground coal mines. Research showed that lineament (linear feature) analysis of Landsat Multispectral Scanner (MSS) images could indicate locations of fractures and fracture trends that had varying, but significant, impacts on the stability of mine openings. Such geologic structures should be identifiable over abandoned mines as well. If fractures are present, even if they arc not faults, they should represent areas of potential instability over these mines and, therefore, should tend to localize subsidence when it occurs, particularly for deep and moderately deep portions of mines.

Jan 1, 1992

By Guy A. Johnson

The Bureau of Mines, through research and development contracts with the FMC Corp., has developed and tested two automatic fire sensing and suppression systems for large haulage vehicles. This work was undertaken to enhance driver safety, to lessen substantial property damage from fires on large trucks, and to increase the vehicle operator's productivity. One automatic truck fire protection system protects both the engine compartment and brake rid areas, while the second system is used in the engine compartment and fuel tank area. Both systems have redundant fire-sensing capabilities and manual override controls. Upon sensing flames and/or heat, the systems suppress the fire with pressurized, E-C class dry chemical. Both fire protection systems are flexible in design and can be modified for use on other mobile minim' equipment. Prototypes of both systems have been subjected to long-term, in-mine validation testing and actual Eire tests on 100-ton-capacity trucks at the Puma mine near Tucson, Ariz., and the Erie mine at Hoyt Lakes, Minn. During the 4-month endurance test of the first system at Pima, an accidental flash fire occurred in the test truck while it was working in the pit. The system successfully sensed and automatically extinguished the fire with no injury to the driver and little damage to the truck.

Jan 1, 1975

By M. J. Kovalik

Illinois No.6, a high-volatile B coal of low fluidity, was blended with fluidized-bed char and coke breeze to improve the strength of the coke obtained from carbonizing this coal. Twenty-one tests, selected from those made in the small-scale Hanson carbonizer, were carbonized in the BM-AGA 13-inch-diameter, cylindrical retort, with a coal charge of about 90 pounds; the strength of the cokes was determined by the standard ASTM tumbler test. Using the same procedure, 10 tests were made with High Splint, a high-volatile A coal from Harlan County, Ky. Carbonization of the blends produced larger and stronger cokes than did the Illinois No.6 coal singly. The optimum blend contained 6 percent each of char and coke breeze. Further improvement in coke strength was realized by either preheating this blend prior to carbonization or by adding a small pro-portion of a premium blending coal. The former method could possibly eliminate the use of premium coking coals in blends with Illinois No. 6 coal to make an acceptable metallurgical coke. Except for no improvement in coke strength by preheating, results for High Splint coal showed behavior similar to that of the Illinois No.6 coal.

Jan 1, 1973

By James H. Aase

Selected glacial lake clay deposits in Minnesota were sampled, tested, and evaluated to determine their suitability for use as a bonding agent in iron ore pellet manufacturing. Preliminary tests conducted on clay samples obtained from five ancient glacial lake basins identified the clays in the Lake Agassiz glacial lake basin near Cook, Minn., as having the greatest bonding potential. An auger drilling program was conducted to obtain substantial quantities of representative material for detailed testing. The drilling indicated the presence of large clay reserves in excess of 500 million tons within the 12-square-mile area investigated. Bench scale tests indicated that the bonding properties of Cook area clays, when activated with relatively small quantities of sodium carbonate monohydrate (Na2C03?H2O), imparted excellent strength characteristics to iron ore pellets. Larger scale continuous pelletizing tests were made to confirm the bench scale results. These tests indicated that use of 1 percent activated clay alone as binder gave the iron ore pellets an overall strength slightly lower than with 0.75 percent bentonite, considered the industry standard. Use of 0.5 percent activated clay plus 0.5 percent bentonite produced better pellet strength qualities than use of 0.75 percent bentonite alone, without increasing the silica plus alumina content. The data from both bench scale and larger scale continuous tests suggest that the Cook, Minn., clays can be utilized after activation either alone or in combination with bentonite at an economic advantage over present pelletizing practice with bentonite.

Jan 1, 1968

By J. Feldman

This report contains a description of the distillation laboratory at Bruceton, Pa., which was established to aid in the separation and identification of the products produced in the synthetic liquid fuel processes under study there. Compounds present in synthetic liquid fuels may include aliphatic from C1 to C60 or greater. Alcohols, ketones, esters, aliphatic carboxylic acids, saturated hydrocarbons, olefins, and diolefins are all found in Fischer-Tropsch products. Coal-hydrogenation products contain, in addition to aliphatic compounds, a large proportion of naphthenic material and aromatic compounds ranging from benzene to coronene; in addition, appreciable quantities of tar bases and tar acids are present. In designing the laboratory, therefore, provision had to be wade for the greatest amount of flexibility and versatility. A great deal of standardization of basic equipment had also to be designed to permit interchange of parts and services.

Jan 1, 1951

By R. R. Sayers

carbon monoxide mav occur in many places and inhalation of that insidious s is a. frequent and .videly distributed cause of poisoning, ranging in severity from headache and. inefficiency to unconsciousness and death. People are continual­ly being affected by carbon monoxide 1n the home, in garages, around gas and gasoline engines and blast-furnaces, in fighting fires, after blasting in mines and quarries, and after mine fires and explosions; in fact, everywhere there is the possibility of an exposure to the products of combustion of carbonaceous fuels or products, On the other hand, there are arzy' cases reported wherP. ill effects and acci:ients are wro:1gly .ttributed to carbon monoxide. Thus it is essential indeed for doctors, coroners, safety engineers, a.n1 !irst-aid men to be able to recognize this poisoning, not only as reeards giving proper treatment, but to ensure just decisions on claims and to eliminate false illusions and complaints of ·11orkrr.en.

May 1, 1922

By T. E. Sterner

A laboratory investigation was conducted to determine the applicability of the thermal oil-recovery method as a means of increasing ultimate oil recovery in the Appalachian region. The primary objective was to establish self-sustained combustion in consolidated and unconsolidated sand test assemblies saturated with various amounts of Pennsylvania Grade crude oil and synthetic brine. Tests using blocks of sandstone were unsuccessful because of sealing problems and fracturing of the rock due to thermal stresses. A combustion wave of about 700° F was propagated through the sand-oil-water packs in the linear tube tests. The high air flux used resulted in high oil consumption and rapid movement of the combustion wave through the tubes. Analytical tests on the sand pack showed that sufficient fuel was deposited during the linear tube experiments for a self-sustained combustion wave.

Jan 1, 1967

By Jalna R. Zatko

The Bureau of Mines, U.S. Department of the Interior, has developed a novel method of flocculation dewatering of phosphatic clay wastes using polyethylene oxide as the flocculant. Research was conducted to determine whether ethylene oxide gas was present in the air in the vicinity of disposed waste materials which had been flocculated with polyethylene oxide. Samples of clay waste materials containing polyethylene oxide were prepared in stoppered glass bottles in simulated disposal environments. Gaseous samples, removed over a 75-day period using an airtight syringe, were injected into a gas chromatograph that was capable of separating ethylene oxide from air. The presence of ethylene oxide gas was not detected in any sample. To determine possible degradation products of polyethylene oxide, the properties and reactions of ethylene oxide and its polymers were reviewed. Based upon the literature survey and experimental study, it was concluded that adverse environmental effects were not likely to result from the use of polyethylene oxide for flocculating phosphatic clay waste products.

Jan 1, 1980

By George H. Schnakenberg, Aleksandar D. Bugarski

This report reviews the performance and applicability of technology for the control of emissions from diesel-powered equipment used in underground coal and metal/nonmetal mines. The methods discussed include Mine Safety and Health Administration-approved low-emission engines, engine derating, fuels, fuel additives, diesel oxidation catalysts, and diesel particulate filters. The potential of each of these technologies is examined individually and in combination. The performance estimates are derived from the published literature and presented in narrative and Tabular form. The purpose of this report is to help the mining industry select the most appropriate method to reduce underground exposures of miners to diesel exhaust in the context of the recently developed diesel regulations. It is important to note that the control technologies discussed in this report have received limited evaluation in underground mines. Additional research is ongoing, and some engineering design changes may need to be implemented before all of these diesel emission control technologies can be safely and successfully used in underground mines.

Jan 1, 2002

By Clete R. Stephan, Mark J. Schultz, William A. Slivensky, Eric S. Weiss, Kenneth W. Jackson

he Pittsburgh Research Center (PRC)~ and the Mine Safety and Health Administration (MSHA) are participating in a research program to evaluate the strength characteristics and air leakage resistance of seals and water trap designs for use in underground coal mines. This program is being conducted at PRC's Lake Lynn Laboratory near Fairchance, Fayette County, PA. Seals designed with a 40-cm-thick polymer (polyurethane) and aggregate core between two dry-stacked (no mortar) concrete block walls (coated on out by sides) withstood a 138-kPa pressure pulse while maintaining acceptable air leakage rates. Similar seal designs utilizing a 97-cm-thick, 91-kg/m7-density, polymer-only core did not survive; however, a 5 1 -cm-thick, 203-kg/mi-density, polymer-only core seal successfully withstood the explosion pressures. Evaluations of cellular concrete seal designs have shown that a two-pour slurry injection technique did not adversely affect the strength of the 1.2-m-thick seals when subjected to a 138-kPa pressure pulse. Two seal designs utilizing low-density cementitious block have also been evaluated with successful results. In addition to seal strength tests, various 15- and 30-cm-diam U-shaped water trap pipes and a water trough design were evaluated under explosion conditions and were shown to be inadequate when evaluated under worst-case conditions. Simple modifications to the various water trap designs were successfu1 in preventing the passage of explosion flame through the trap.

Jan 4, 1996

By S. E. Khalafalla

The extremely sluggish oxidation of steel scrap was appreciably accelerated when the charge was pretreated in aqueous solutions of sodium metavanadate or sodium molybdate. The degree of oxidation acceleration was inversely correlated with the melting point of the promoter oxide possessing the highest valency. The magnitude of oxidation enhancement exhibited a systematic inverse dependence on the duration of pickling processes; mere dipping of the oxidizable charge in the vanadate bath was most effective. In general, the rate of steel scrap oxidation increased with increasing concentration of the pickling reagent. The results are explained on the basis of the hydrolytic decomposition of the pickling agent with subsequent slow interaction with the metal surface, coupled with the tendency of vanadium to form polyanions in alkaline media. The data not only served to elucidate the mechanism by which catastrophic oxidation takes place, but also showed that the accelerating species need not be alloyed with the oxidizable metal; surface impregnation by minute amounts of the accelerating species can still produce catastrophic effects.

Jan 1, 1970