Search Documents

By G. R. Friggens

A nuclear method for continuously monitoring the coalbed and ash levels and void formation in commercial-scale, fixed-bed, pressurized gas producers is proposed. Measurement of gamma ray transmission through the coalbed is the basis of the method. The coalbed level is monitored by detecting the trans-mission of gamma rays from a 1 to 2 Ci Co-60 source positioned on the outside wall of the vessel. Coal bridging or, alternatively, ash level is monitored by a 10 Ci Co-60 source at the center of the coalbed. Source activities and geometries are calculated for a 12-foot-ID producer designed to operate at 350 psi. Source capsule and detector specifications and operational safety are also discussed.

Jan 1, 1973

By H. B. Carroll

The Bureau of Mines investigated the adaptability of the Meteorology Research Inc.2 (MRI) nephelometer and the Sinclair-Phoenix smoke meter for use in routine, analytical, smog-chamber experiments and to compare their responses to aerosol during these experiments. Both instruments' sampling systems were modified--smaller size sample input systems were studied using the nephelometer and a secondary sample system was added to the smoke meter to allow measurement of Aitken or condensate nuclei. Both instruments were easily adapted for use with small smog chambers and both displayed good precision and sensitivity to aerosol. A correlation was shown to exist between the two instruments' responses to aerosol. This correlation makes it possible to report the Sinclair-Phoenix measurements in visibility and/or mass units if desired.

Jan 1, 1973

SCOPE AND APPLICATION The rules cover the installation and use of electrical equipment in coal mines.- For generating stations, substations, lines, and equip¬ment aboveground, reference is made to existing rules covering such locations, viz, the National Electrical Code and the National Electrical Safety Code and any existing State or municipal regulations. The purpose of the rules is to set forth methods for safe electrical installation. In preparing the rules five basic measures for safe¬guarding the use of electricity in mines have been followed, viz 1. Remove the contributory causes of accidents or danger. 2. Remove from the vicinity of electrical apparatus all elements susceptible to the influence of electricity. 3. Keep the electric current where it belongs, if possible; if not, limit the area of its activity by protective devices. 4. Use a. large factor of safety in the selection, installation, and in¬ spection of equipment. 5. Have full control of the operation of electrically driven machines. Each rule that is given is proposed as necessary or helpful to the accomplishment of one or more of these measures. DEFINITIONS OF TERMS USED Alive.-See definition of " live." Approved.-The term " approved " means accepted as suitable by a competent committee, board, or organization designated by those adopting the rules. Authorized person.-The term " authorized person " means a per¬son appointed or permitted by the official designated by the State mining laws as the one in charge of the operation of the mine to carry out certain duties incident to the generation, transformation, and distribution or use of electric energy in the mine, such person be-

Jan 1, 1926

By T. R. Waters, F. Li, R. L. Huston

This paper describes the development of a multi-body biomechanical model that can be used to assess the risk of low back disorders due to occupational exposure to jarring and jolting from operation of heavy mobile equipment (e.g., trucks, haulers, graders, tractors, etc.) The four-element dynamic spinal model is capable of providing estimates of the force and acceleration responses of the head/neck, upper, lower, and middle torso resulting from vibration input collected in field studies. The paper also presents a method for using the model output to assess an individual's risk of low back disorder due to a specific jarring and jolting exposure.

By Joseph Cervik

Coal is a soft and brittle material. Drilling rates in the Pittsburgh coalbed using a drag bit exceed 3 ft/min at 2,500-pound thrust. However, maintaining the bit on a horizontal trajectory or parallel to bedding planes to attain lengths of 1,000 feet is difficult. This Bureau of Mines report presents a drill string configuration that can be guided through the coalbed. The angle of the borehole is measured periodically and by proper combinations of bit thrust and rotational speed (r/min), bit trajectory can be lifted or dropped to keep the bit in the coalbed. An example of a hole drilled to 2,126 feet is presented to show levels of thrust and rotational speed used to lift or drop the bit, the seemingly unexplainable events that occur, and the strategy used during drilling. Thrust levels during drilling range from 600 to 2,500 pounds. Hydraulic motors powered by a 30-hp, 440-volt motor provide ample power for drilling horizontal holes 2,000 feet long.

Jan 1, 1975

By John C. Franklin

The Bureau of Mines conducted extensive laboratory and limited field tests to determine whether a polymeric material could effectively reduce the emanation rate of radon gas from uranium ore. In the laboratory 46 different single-coat materials and 14 two-coat applications were tested. The laboratory tests showed that up to 100 percent of the radon gas could be sealed into the rock. Materials tested in the laboratory were polyesters, furan resins, epoxies, latices, and totally inorganic coatings. From the laboratory work six different materials were selected for field testing. The first test was single-coat materials in five static chambers; the second test used two-coat applications in an open chamber. Both tests were conducted in the Dakota mine at Grants, N. Mex. During the second test, the amanation rate of radon gas was reduced up to 62 percent.

Jan 1, 1975

By R. P. Vinson, Abdurrahman Cetinbas, Joseph Cervik, M. G. Zabetakis

The periphery of longwall panels in the Pocahontas No. 3 coalbed is characterized by a zone of reduced permeability that inhibits the natural drainage of methane. A residual gas pressure of 105 psig was measured after 1 year in an isolated block of coal measuring 340 by 1,100 feet. The buildup of gas pressure within such large blocks causes methane problems during plowing operations. However, natural drainage holes drilled during development have been found to reduce the gas content of the coal in this coalbed by over 90 percent. The effect of water infusion on dust during plowing operations was investigated using existing methane drainage holes. These holes were cleaned of debris and a pipe was grouted into the hole for water infusion of the panel. Both total and respirable dust levels were reduced by 40 to 79 percent. Water infusion of the panel proved more effective than did the use of a plow-mounted spray sys tem.

Jan 1, 1974

Design a model health and safety program which, when implemented, can improve mine safety by reducing occupational injuries and accidents. Approach The Bureau of Mines developed a model program which identifies the elements essential to the effectiveness of health and safety programs designed for mining operations, and is readily adaptable to all types of sizes of mines. The model program primarily provides training on loss control and accident investigation and technical assistance with health and safety problems. In order to assess the effectiveness of the program, it was tested at both a coal and gold mining operation. Monthly statistics were generated to reflect the number of occupational injuries and accidents, and the severity of injuries (as measured by the number of work days lost during recovery). Observations were made of employees performing a large number of randomly selected jobs in order to estimate. the proportion of the workforce that was working in the presence of one or more of three types of safety deficiencies: Type A-individual job performance deficiencies which could be corrected by the employee alone I e.g., an employee is seen not wearing a seatbelt.

Jan 1, 1986

By Paul W. Jeran, Michael A. Trevits, William P. Diamond

In this U.S. Bureau of Mines study, production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 to 10.1 x 106 m3. Peak production rates were generally about 0.03 x 106 to 0.06 x 106 m3/d, but rates over 0.10 x 1@ m3/d were observed. The variability of gas production from individual holes can be attributed to several factors, including completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance is hole location. Holes on the ends of the panels, where overburden strata are in tension because of the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location, which is in compression. Analysis of 7 months of gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 1994

By E. C. Bennett

"INRTODUCTIONVarious methods of making leakage tests have been tried during a study of losses in the transmission of natural gas. This work has been carried on by the Bureau of Mines in cooperation with the Natural Gas Association of America. Results of torts show that the ""shut-in -pressure-drop"" method described by Rawlins is the most accurate and reliable; therefore its use is recommended. This paper describes a graphic method for computing the rote of leakage from the fall in pressure and change in temperature determined by the ""shut -in pressure-drop"" method of testing.METHOD OF MEASURING PRESSURE DROPThe gas is ""shut in"" line to be tested and is not allowed to escape except through existing leaks. The leakage causes the pressure in the line to fall. The charge in pressure is obtained with a dead weight gage. Approximate results may also be obtained from readings on a good spring test gage. Numerous tests show that the dead weight gage is more sensitive to small changes in pressure than spring gages.The temperature of the gas in the line is observed simultaneously with each pressure reading. Temperature changes affect the pressure exerted by a given quality of gas ""shut in a line, end since the rate of leakage from a closed system is directly proportional to the rate of pressure drop, fluctuations in temperature must be considered."

May 1, 1926

By Mark Colwell, Russell Frith

This paper summarizes the results of a research project whose goal was to provide the Australian coal industry with a chain pillar design methodology readily usable by colliery staff. The project was primarily funded by the Australian Coal Association Research Program and further supported by several Australian longwall operations. The starting point or basis of the project was the Analysis of Longwall Pillar Stability (ALPS) methodology. ALPS was chosen because of its operational focus; it uses tailgate performance as the determining chain pillar design criterion rather than simply pillar stability. Furthermore, ALPS recognizes that several geotechnical and design factors, including (but not limited to) chain pillar stability, affect that performance. There are some geotechnical and mine layout differences between United States and Australian coal fields that required investigation and, therefore, calibration before the full benefits offered by the ALPS methodology could be realized in Australia. Ultimately, case history data were collected from 19 longwall mines representing approximately 60% of all Australian longwall operations. In addition, six monitoring sites incorporated an array of hydraulic stress cells to measure the change in vertical stress throughout the various phases of the longwall extraction cycle. The sites also incorporated extensometers to monitor roof and rib performance in response to the retreating longwallface. The study found strong relationships between the tailgate stability factor, the Coal Mine Roof Rating, and the installed level of primary support. The final outcome of the project is a chain pillar design methodology called Analysis of Longwall Tailgate Serviceability (ALTS). Guidelines for using ALTS are provided.

Jan 5, 1999

By A. B. Hooker

Investigations at the Pittsburgh Experiment Station have shown that the satisfactory operation of a flame safety lamp depends not only upon proper design and assembly of the lamp but upon the kind of fuel used, and that much of the trouble experienced with permissible flame safety lamps at mines is due to the common use of motor gasolines, none of which is suitable in the present types of permissible flame safety lamps. This report gives the results of a limited study to determine what satisfactory fuels are available, the specification limits of such fuels, and to suggest modifications of assembly and care of the lamps to improve performance with any satisfactory fuel.

Jan 1, 1938

By Richard J. Mainiero

The Bureau of Mines investigated coal-mine-type short-delay electric detonators marketed by three domestic manufacturers to determine the accuracy of delays and the probability of overlap between adjacent de- lay periods. The Winzer index was computed and compared with the probability of overlap. A close agreement between the Winzer criterion and overlap probability was demonstrated. A permissible blasting unit capable of delivering a maximum firing energy of 4.0 J and a digital oscilloscope were used to measure the delay time with an accuracy of 20.25 ms. Another oscilloscope and a pulse transformer were used to record firing current. Experimental data indicated negligible overlap probability in detonators of shorter delay periods: periods 1 to 4, which correspond to 25 to 250 ms. However, a significant probability of overlap was detected in some detonators of longer delay periods: periods 5 to 9, which cor- respond to 300 to 500 ms.

Jan 1, 1985

Compare the dust control efficiency and bit life of surface coal mine drills using standard water injection and water injection with water separation. Approach A research study was conducted to determine if a water separation technique affects wet suppression dust control. Dust control efficiency and bit life of surface coal mine drills were compared during tests using both standard water injection (wet drill bit cutting) and water injection with water separation (dry drill bit cutting). Background Surface coal mine blast hole drills typically generate a substantial amount of dust during the drilling cycle. One method used to control this dust is the injection of water into the bailing air. This is known as wet suppression.

Jan 1, 1988

By William Wiehagen

This trainer?s guide is designed as a reference manual. The purpose is to offer information and examples to skills trainers to assist them in structuring training for new operators of Walk-Thru roof bolting machines. Trainers can use this manual as a resource for helping trainees learn, understand, and apply knowledge and skills. In this sense, the guide is not prescriptive. It is designed to offer information and trigger ideas on what might be done to accelerate learning to those who are new to the roof-bolting task. On-site trainers can modify this guide to fit their conditions, machines and equipment, and work procedures. They can integrate roof control plans, company policies and procedures, and operators? manuals from the manufacturers of the original equipment into this guide. Every trainee is different and will come to the job with varying levels of relevant knowledge and skills. The trainer?s decisions on where to start, how to organize the on-the-job and classroom training portions, and when and how to offer different aspects of the training will be based on (1) a pretraining assessment of the trainee?s knowledge and skills and (2) the trainer?s experience in conducting skills training. The ?Skill Check? section might be useful for deciding where training should start among miners who have underground experience but limited knowledge of roof-bolting techniques. Every job carries a learning curve and likely has a number of ?teachable moments? where significantly new knowledge and skills can be learned.

Aug 1, 2006

By Thomas V. Falkie, R. Venkataramani

Table

Jan 1, 1972

By Thomas M. Barczak, Ron Smith

Steel liner plates, which are bolted together to form a shell, are commonly used to provide temporary protective linings in the tunneling industry to ensure the stability of the tunnel and safety of the workers until more permanent ground reinforcement can be installed. As the ground deforms to try and close the opening, the liner plate is radially stressed, and by deforming redistributes these loads back to the surrounding insitu earth. Grouting behind the plates is done to fill any voids and ensure uniform contact to the strata around the back of the plates. Another function of the liner plate in some applications is to act as a platform or structure for the mining machine to react against in order to develop the necessary forward thrust to be able to excavate the face. In this case, the liner plates are loaded axially as a horizontal column of bolted liner plate rings, creating a jacking force against the liner plate assembly. In general, the buckling strength of the plate sections determines the jacking force capacity. Historically, the jacking force capacity of tunnel liner plates has been theoretically determined by some simplistic equations developed from tests of single liner plates. Recently, full-scale tests on a complete circular section of bolted liner plate ring segments have been conducted in the NIOSH Safety Structures Testing Laboratory using the unique Mine Roof Simulator to apply controlled loading in a manner that simulates the real world environment. Due to the unique size and capacity of the Mine Roof Simulator, these are believed to be the first full-scale tests conducted on the jacking force capability of tunnel liner plate rings. These tests indicate that the previously used theoretical equations tend to over predict the jacking force capacity of these tunnel liner plates. Unanticipated deformations in the field have been observed at loads below these theoretical design loads, therefore, a more accurate determination of the jacking force capability was needed. This report summarizes the full-scale test results, examines design parameters that impact the jacking force capability, and develops new mathematical models to improve the prediction of design loads.

By D. G. Kesterke

The electrolytic reduction of uranium dioxide to molten uranium in fluoride baths at approximately 1,200° C was demonstrated. Electrolyte constituents were BaF2, UF4, and either MgF2 or LiF. Preliminary laboratory-scale experiments were made in which the uranium oxide was added continuously for 3 to 5 hours to the cell during electrolysis. Over 1,000 grams of metal of 99-8 percent purity was made in some tests, Major impurities were aluminum, barium, iron, silicon, carbon, and oxygen. The effects of cell design, geometry, and bath composition were investigated. Electrode arrangement was the most important factor in cell performance.

Jan 1, 1963

By J. E. Murphy

Field freezing was used by the Bureau of Mines to effect the redistribution of the components in a cerium-12.5-atomic-percent-iron alloy. The application of the electric field caused the iron to migrate toward the anode. A field intensity of 0.04 v/cm and a current density of 240 amp/cm2 were used. The conditions that yielded the greatest redistribution of alloy components were a small thermal gradient along the specimen (from 5° C/cm to 10° C/cm) and a very slow freezing rate (0.15 cm/hr). Under these conditions it was possible to process specimens of ½ -inch diameter as compared with the capillary-size specimens used by most previous investigators.

Jan 1, 1968

By B. T. Brady

Results of a study are presented of the effect of low radial reinforcement pressure on the postfailure characteristics of two types of granite, a sandstone, and marble. The low radial reinforcement pressure is applied to the rock surface by a gooch rubber sleeve. The gooch rubber sleeve provides a radial pressure of less than 1 psi pressure to the rock surface. This method of support gives an average strength increase of approximately 8 percent to the fractured rock sample.

Jan 1, 1973