Search Documents

By T. R. Taubert, D. H. Carlson, J. H. Johnson

"ObjectiveDevelop a portable emissions measurement apparatus to sample and measure tailpipe concentrations of diesel particulate matter (DPM), carbon monoxide (CO), carbon dioxide (COJ, nitric oxide (NO), and nitrogen dioxide (NOJ under steady-state engine load and speed conditions during a 1-minute test.BackgroundThe U.S. Bureau of Mines (USBM) has a comprehensive research program to develop ways to reduce exposure of miners to diesel exhaust pollutants. Engine maintenance has been shown to have important effects on such exposure.Accurate measurements of tailpipe emissions are becoming an essential part of a good maintenance program for underground mines that use diesel-powered vehicles. Past studies of particulates in U.S. underground coal mines have shown that DPM alone may be present at concentrations greater than 1 milligram per cubic meter (mg/m3), half the 2-mg/m3 limit for respirable coal mine dust. A poorly tuned (smoking) diesel engine may be the sole cause for respirable dust concentrations exceeding the limit. Although there is currently no standard specifically for DPM in U.S. mines, regulatory steps are underway, and significant reductions of DPM levels in both coal and metal mines will most likely be required.Tailpipe emission measurements can provide diagnostic information to identify engine malfunctions such as clogged air cleaners, faulty injectors, or incorrect injection timing. In some cases, mine vehicle tailpipe DPM concentrations have been reduced up to 50 percent by engine maintenance and adjustments.An accurate measuring instrument would also be useful for determining the effects of exhaust control devices on tailpipe emissions. Little information is currently available about the overall effectiveness of exhaust controls after long-term use. Raw exhaust concentrations with and without the control device can be measured in underground mines, and from these data a control efficiency can be calculated. Knowledge of the effectiveness of exhaust control devices over time is needed to make intelligent decisions on bow to use and maintain these devices, and when to replace them."

Dec 1, 1995

By H. W. Kilau

Thermodynamic calculations indicate that an electrochemical cell might serve as an analytical device for determining the composition of high-purity metals. An equation, readily derived, for the cell voltage, E, is as follows: [E I RT In F NFe unknown sample T of L NFe standard] The cell, however, must come to equilibrium, must be reversible, and must have no thermal effects or complicating side reactions whose magnitude is indeterminable. This Bureau of Mines investigation explores the feasibility of an electrochemical technique for the analysis of high-purity iron. Experiments were conducted using room-temperature aqueous cells and high-temperature molten salt cells. The room-temperature cells proved to be irreversible. The high-temperature cells utilizing FeCl2 and a eutectic mixture of KC1-LiCl were reversible, but did not attain a constant voltage necessary for analytical considerations.

Jan 1, 1963

By H. G. Lucas

A feeder screw supplied at constant pressure by a hopper-orifice arrangement was developed for feeding solids in size ranges up to several hundred micrometers at constant flow rates. Performance of the feeder was evaluated by measuring the flow rates obtained with 3-to 7-micrometer coal ash, 70 percent through 200-mesh coal, and minus 325-plus 400-mesh coal ash. Constant feed rates within a few percent of set values were achieved for half-hour periods for the larger particles and for 5-minute periods for the finer particles. Suggestions are given for feedstock preparation and feeder operation for optimum performance.

Jan 1, 1974

By Wilbur I. Duvall

Surface vibrations of ground, rock, and structures resulting from blasting or other sources are often measured with portable seismographs. These instruments are usually supported by a three-point mount or tripod which is simply placed on a horizontal surface on which vibration levels are to be measured. The rigid-body motion of a tripod-supported seismograph is considered from the point of view that there should be no slippage of the feet with respect to the surface and none of the feet should leave the surface as a result of imparted motion. From these studies the following design criteria are deduced which assure that the seismograph will respond accurately to vibration levels as large as 1/2 g.:3/ First, the coefficient of friction between the feet and the surface on which the instrument rests should be as large as possible, preferably approaching unity; second, the center of gravity of the instrument should be vertically above the centroid of the three-point mount; and third, the vertical distance between the center of gravity of the instrument and the centroid of the three points of contact with the surface should be less than the perpendicular distance between the centroid point and anyone of the three sides of the triangle formed by the three points of contact. Portable seismographs that do not satisfy these conditions should be clamped to the surface if vibration levels above 0.1 g. are to be recorded.

Jan 1, 1961

By Franklin D. Cooper

This Bureau of Mines study reviews current and proposed methods of extracting copper from sub-mill-grade ore by leaching. The amount of copper produced by hydrometallurgy has increased dramatically in recent years and will probably be about 200,000 tons per year by 1970.

Jan 1, 1968

By A. W. Maynard

Simple chemical spot tests for the identification of major alloying elements in aluminum-base alloys are described. The tests are suitable for use by nontechnical personnel working outside a laboratory. Tests for zinc, copper, manganese, and magnesium employ electrographic sampling methods and sample papers. Use of electrographic sampling in a test for magnesium in aluminum is made possible by using glass fiber filter paper. Differentiations between magnesium and magnesium-silicon alloys of aluminum and between aluminum-base and magnesium-base alloys are made by direct chemical solution tests. Description of a device for obtaining reliable electrographic samples is included. A sequence of testing for identification by alloy groups is given.

Jan 1, 1971

By H. Carroll

An ozone detector was built and evaluated for its applicability in smog-chamber studies. The detection method is based on the reaction of ozone with ethylene and the measurement of resultant chemiluminescence. In the first phase of evaluation, the detector's response to ozone was studied as a function of several instrument parameters, and optimum conditions were defined for the maximum and most stable responses to ozone. In subsequent evaluations, the method was checked for sensitivity, precision, and interferences and was compared with two alternative methods. Results showed the chemiluminescence method to be acceptably sensitive and precise for smog-chamber studies and superior to the Mast ozone meter and KI (colorimetric 1 percent neutral-potassium iodide method) methods in that it is specific for ozone.

Jan 1, 1972

By W. J. Wenger

Results of the analyses of 151 crude oils from 123 oilfields in the Williston basin are presented. Production statistics are compiled by geographical areas within the basin, by geological age of the producing zones, by States, and by field for the nine fields with the greatest production. Characteristics of the oils are tabulated, and correlations are included to show relationships between properties of the oils and some factors in the environment. Properties of the oils in some instances imply that there has been migration and mixing of the oils between productive formations of different geological time periods.

Jan 1, 1968

By A. J. Miscoe

A unique machine for inducing bending fatigue in wire ropes was built at the U.S. Bureau of Mines' Pittsburgh Research Center. This machine can produce nine levels of degradation through repetitive cycling of long samples of wire ropes of the types used in the mining industry. This report provides an analysis of the results of the first wire rope to be fatigued on this machine. These results have indicated that as a wire rope accumulates bending cycles, its strength first decreases because of wear and then in-creases due to cold working of the wires. As the amount of cold working increases, more and more of the embrittled wires break and the strength of the rope decreases rapidly. In this test, application of several of the regulatory retirement criteria to various sections of the rope suggests that there may be some inconsistency among them.

Jan 1, 2010

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

THIS PROGRAM TRANSFORMS FREE FORHATED BRANCH DATA INTO A FORMAT SUITABLE FOR INPUT TO THE PENNSYLVANIA STATE UNIVERSITY MINE VENTILATION SIMULATOR (PSU/HVS 1. BRANCH RESISTANCES ARE ASSUMED TO HAVE BEEN ALREADY CALCULATED, IIOWEVER THIS PROGRAM CAN BE EASILY MODIFIED TO HANDLE THE ADDITIONAL INPUT DATA REQUIRED FOR RESISTANCE CALCULATIONS IN THE PSU/MVSO THE PROGRAM IS WRITTEN IN FORTRAN IV WITH WATFIV.

Jan 1, 1977

By V. A. Marple, K. L. Rubow

"Filter samplers are one of the simplest methods and, in some instances, one of the only methods that can be use to obtain samples of particulate matter suspended in a gaseous medium. Once collected, particles are normally analyzed directly on the filter by gravimetric, chemical or microscopic techniques. However, it is sometimes desirable to resuspend the particles in an airstream for analysis. This would be the case if the size distribution of the particles were to be measured using one of many particle sizing techniques such as inertial classifiers, optical particle counters or the TSI Aerodynamic Particle Sizer CAPS).A ·technique has been recently developed whereby one can resuspend particles from filter samples in an airstream. The technique has been used for the resuspension of coal dust from filters. The resuspended particles were then introduced into the APS. This development was necessary since an APS can not be taken directly into an underground coal mine. For this application, particle samples are collected on membrane filters in the underground mines. The mass concentration of the particles determined through gravimetric analysis. The particle size distribution was tl1en determined by resuspending the particles and passing them through a TSI Aerodynamic Particle Sizer (APS). Excellent agreement has been obtained between the size distribution directly measured underground with a cascade impactor and that measured from the resuspended particles. For this experiment, an open-faced filter sampler was placed adjacent to the cascade impactor in the n1ine. The particles collected on the filter were resuspended in the laboratory and Measured with the APS.A venturi aspirator is used in the apparatus developed for resuspending the particles. The venturi has a small diameter capillary tube placed in the venturi throat. High velocity air flow is passed through the venturi, thereby, creating a low pressure region at the exit of the capillary tube. The low pressure draws air through the tube. The filter with deposited particles is located at the inlet to the capillary tube where the air flow into the capillary resuspend the particles. Once airborne, the particles are deagglomerated as they pass through the high velocity air flow in the venturi throat."

Jan 1, 1989

By Timothy J. Orr, Michael J. Beus, Frank T. Duda

The technology to enhance safety and control features for mine shaft hoists is being investigated by researchers at the U.S. Bureau of Mines (USBM). The objective of the research is to prevent injuries and fatalities related to hoist and elevator operations. Monitoring and controlling mine hoisting operations will allow hoist operators, inspectors, and maintenance personnel to increase their awareness of potentially dangerous situations and provide controls for safer operations. Process simulation and visualization software, real-time data sensing, and advanced programming techniques are being applied to this problem. Development of reliable and cost-effective sensors and data acquisition interfaces to monitor hoist loads and detect slack rope conditions is underway. Three-dimensional design software was used to visualize mine hoisting to enhance understanding of hoist operations. Quick Basic and Visual Basic (an object-oriented Windows interface) are being used for acquiring and processing hoisting data. Testing and evaluation of components are underway at USBM testing facilities. The resulting system will allow hoist personnel to assess critical operating parameters, such as hoist position, speed, acceleration, conveyance load, and rope tension.

Establish a procedure for reliably determining cation exchange parameters at an in situ mining site. The Problem Predicting the movement rates of pollutants from waste disposal sites requires reliable measurements of cation exchange parameters since cation exchange can retard pollutant movement. Reliable measurements of these parameters are also required for predicting the length of time needed to restore groundwater quality after in situ mining. Cation exchange is otten the controlling mechanism for the replacement of leach solution cations by the cations in the returning ground-water. Unfortunately, laboratory measurements using core samples are of minimal reliability. The uneven clay distribution at most sites produces a high variability in laboratory results. In addition the flow pattern in the laboratory tests is different from that in the field. Approach Bureau of Mines research has developed a field-test procedure that is quick and yields reliable and representative data. A corresponding data analysis procedure was also established in order to verify the' applicability of the computer simulation model of cation exchange used in the analysis, and of the general analysis procedure, with actual field data.

Jan 1, 1986

By Fred C. Turin, Sean Gallagher, Kim M. Cornelius, William J. Wiehagen

An important part of initiating a site-wide ergonomics evaluation process is prioritizing jobs to be analyzed. While injury data is important, other factors such as worker discomfort and physical exertion requirements, should be considered. This paper describes the use of four sources of data (injury records, the Nordic Standardized Musculoskeletal Questionnaire, supervisor interviews, and management concerns) to prioritize jobs for ergonomic analysis. The approach described integrates the four sources using a decision matrix to prioritize jobs for ergonomics analysis.

Although haulage truck collisions account for only a small percentage of haulage accidents, the likelihood of severe injury, or even death is very high when such a collision does occur. Most rear-end collisions also result in considerable equipment damage, creating a need for expensive repairs. To improve collision protection, some southwestern surface mines have, for several years, been fabricating and using extended bumpers. In cooperation with these mines, the Bureau of Mines has worked to improve this technology by evaluating the structural requiremnts of extended bumpers. How Extended Bumpers Help The Bureau found that when one large rear-dump haulage truck collides with the rear of another an extended bumper protects the driver of the vehicle that is struck by dissipating the impact energy into the rear tires and pushing the whole vehicle forward. An extended bumper also prevents the box on the truck that is hit from penetrating the cab of the other truck-a typical and serious collision hazard. A further advantage derives from the wide design of the extended bumper which helps prevent damage to truck ladders, thereby minimizing any entry or exit problems. Extended bumpers also provide safe work platforms at the front of large haulage vehicles.

Jan 1, 1984

Prevent the propagation of a fire and control the spread of smoke and toxic gas in underground mines. Approach A fire door suitable for large openings in underground noncoal mines and providing protection for openings requiring 11/2 hours of fire resistance, a 250°F maximum temperature rise, and high pressure differentials was de-signed, laboratory tested, and in-mine tested. How It Works The door is a double-acting swing type. Its two panels. connected by an overhead linkage, open in opposite directions. Consequently, high pressure differentials across the door have little effect on the force required to open and close the door. The door is constructed of 14-gauge sheet steel skins welded to both sides of a 5-inch-wide steel channel frame. The frame is rein-forced with 5-inch-wide steel channels in a horizontal and diagonal pattern. The voids between the reinforcing members are filled with a ceramic fiber insulation material to limit the surface temperature rise of the unexposed side of the door during a fire. A fire -resistant neoprene-coated fabric is used to seal around the edges of the door panels. The door is opened and closed by an air cylinder, attached to the over-head linkage and operated by lanyards on either side of the door. The door design includes an optional airlock manway for drifts of adequate width.

Jan 1, 1983

By R. Karl Zipf

A method is presented for creating realistic numerical models for practical coal mine ground control. The method includes procedures to collect the necessary mechanical input parameters from a geologic core log, procedures to set up a model, and procedures to interpret calculation results. The input parameters come from a detailed geologic core log and extensive point load tests of estimate rock layer strength. A suite of material property input parameters is proposed that allows the user to go from core log to numerical model inputs. Rock bolt anchorage properties are also linked to the material properties of each geologic layer in the model. Following this procedure leads to very realistic calculations of the rock failure process and rock support system behavior. These calculations in turn enable realistic comparison of the effectiveness of alternative rock support systems.

Jan 5, 2007

By A. D. Mah

Thermodynamic data on compounds of arsenic and sulfur were critically evaluated by the Bureau of Mines. Changes of standard enthalpy and Gibbs energy, and logarithms of the equilibrium constants were tabulated as a function of temperature for reactions involving these compounds.

Jan 1, 1982

This Information Circular from the National Institute for Occupational Safety and Health (NIOSH) documents and supplements the information presented in a series of workshops held during 2002 and 2003. The primary intended audience consists of all who are involved in developing and conducting miners? training. According to the Mine Safety and Health Administration (MSHA), mine operators reported 240,000 full-time equivalent workers and independent contractors reported 42,000 full-time equivalent workers working on mine property during the year 2000. Unfortunately, these workers have a relatively high risk of suffering serious work-related injuries and illnesses. The mining industry has the highest rate of occupational fatalities among all U.S. industries. The fatality rate is 30 deaths per 100,000 workers compared to 4.6 for all private industry(Morbidity and Mortality Week Report, 2001; NIOSH, 2002).Compared to workers in other industries, miners also have a relatively high rate of nonfatal lost-time injuries, and their injuries tend to be more severe (Bureau of Labor Statistics, 1999). Many miners are also exposed to significant health hazards, including coal and silica dust, diesel exhaust, and noise. More than 1000 U.S. miners die of lung disease each year(NIOSH, 1999).

Jan 1, 2002

By R. F. Abernethy

A chemical method of determining microgram quantities of arsenic in coal was investigated by the Bureau of Mines to supplement a semiquantitative spectrographic method of determining arsenic in coal ash. In accordance with a method recommended by the International Organization for Standardization, 1-gram samples of coal are decomposed by wet oxidation with boiling sulfuric acid (H2S04) and nitric acid (HN03) to remove the organic matter. After heating to fumes of SO3 to remove HN03, the arsenic is separated as arsine by the action of zinc in H2S04 solution. The arsine is absorbed in dilute iodine solution in which the arsenic is determined colorimetrically by the molybdenum-blue reaction. Two modifications of the method for obtaining the arsenic in solution, in addition to the wet oxidation method, give satisfactory results. The modifications are (1) furnace ashing with MgO added to the coal, followed by treatment with H2S04, and (2) extraction of arsenic from the coal by dilute HNO3 without ashing. Float-and sink-tests show that arsenic is associated mainly with mineral matter in the three coals examined. High-temperature ashing tests show that very little arsenic is volatilized from coal ash below 1,000° C, but it is virtually all removed from the ash at 1,300° C.

Jan 1, 1968