Search Documents

By Warren D. Longwill

All known resources within the four proposed RARE II additions to the Yolla Bolly-Middle Eel Wilderness in northwestern California occur in the Gig Butte-Shinbone study area (fig. 1). No mineral resources are Figure 1.--NEAR HERE. known in the East Fork, Murphy blade, or Wilderness Contiguous units. About 2,400 tons (2,177 t) of subeconomic manganese resources averaging 9.5 percent manganese have been estimated at the Blue Jay Mine in the Big Butte-Shinbone unit. In addition about 9,700 tons (8,793 t) of subeconomic chromium-nickel-cobalt resources in thin laterite soil at the Grubstake Prospect contain about 1.27 percent chromium oxide, 0.45 percent nickel, and 0.03 percent cobalt. Adjacent Ultramafic rock outcrops have pods averaging 2.5 percent chromium oxide (Cr203); one pod contains about 40 tons (36 t) of indicated subeconomic resources.

Jan 1, 1981

Provide a low-cost, low-maintenance method for im¬proving mine water quality on abandoned mine land (AML) sites. Approach A model (figure 1) is presented for selecting, designing, and sizing one or several passive mine drainage treatment systems that can be used in remediation of AML. The three principal types of passive mine drainage technologies for the treatment of coal mine drainage are an aerobic system, a compost wetland, and an anoxic limestone drain. The multistep approach presented here provides a simplified method to characterize the type and magnitude of the water quality problem and then to select either a single treatment system or a combination of treatment systems to address the specific site situation. How It Works Step 1. Discharge Characterization. Characterization of the discharge consists of measuring the discharge flow rate and collecting water samples at the point of discharge for chemical analysis. Both the flow rate and chemistry of a discharge can vary seasonally and in response to storm events. It is important to account for this variability by determining flow rates and water chemistry under various conditions. Water should be analyzed for pH, dissolved iron (Fe), alkalinity, and hot acidity (using the H2O2 method).

Jan 1, 1994

By Homer J. Ballinger

The Rex mine is one of several zinc deposits in Ozark and Howell Counties, Mo. It is the second of these deposits investigated by the Bureau of Mines in an effort to demonstrate reserves of sulfide ore underlying the shallow carbonate ores from which the district's major production has come. The initial investigation was made during 1945-46 on the Alice mine, Ozark County, Mo.21 The investigation reported herein was conducted during 1947. The Rex open pit is about 250 feet long, 100 feet wide, and about 25 feet deep (average). Three caved shafts are evident in the bottom of the pit, but the extent of the workings from these shafts is not known. The Bureau of Mines drilled five churn-drill holes in and around the Rex pit to test the grade and the vertical and lateral extent of the deposit. Two of the holes indicate notable zinc mineralization ranging from less than 1 to more than 10 percent metallic zinc, but largely in the oxidized condition.

Jan 1, 1948

By Byron S. Gottfried

This Bureau of Mines report presents a method for combining the distribution curves at different specific gravities of separation, for a given piece of coal-cleaning equipment and a given raw coal feed, into a single, generalized distribution curve normalized with respect to specific gravity and, therefore, independent of the specific gravity of separation. Illustrative generalized distribution curves, based upon Bureau of Mines collected data on industrial operations, are presented for five different types of coal-cleaning equipment. The well-known concept of probable error is extended to the generalized distribution curve. It is shown that the conventional probable error is directly proportional to the specific gravity of separation. A number of sample calculations, illustrating the use of the generalized distribution curve and generalized probable error, are presented in the appendix.

Jan 1, 1977

By A. R. Elliott

"In addition to the usual interpretation that is placed on the words ""thief"" and ""thieves"", the petroleum industry also uses these words when referring to an instrument that is used for taking samples of oil from a tank or reservoir. It is an abbreviation of the term ""thief-tube"". It is desirable in sampling volumes of oil in tanks or reservoirs to obtain samples at different intervals below the surface of the fluid, because of the variation in the character of the oil at different depths. It is for this purpose that the ""thief"" is used.The subject of oil thieves is probably as old as the oil industry itself. Opinions as to which is the most practical instrument for thieving oil in tanks, to obtain a true average sample, differ wherever oil is produced and is analyzed. Every district, and even many of the companies within the district, will have different appliances for ""grabbing"" oil samples. It is interesting to note in passing that though the thief has an apparently insignificant part in the handling of oil, yet the results depending on it are of paramount importance practically every branch of the transportation, refining, and marketing of petroleum. Determinations, particularly dependent on a representative sample, are made by the centrifuge, laboratory distillation tests, and the hydrometer.The purpose of this article is to discuss conditions found in the California fields. Only a general description of types of thieves and the methods of using them will be given. However, it is believed sufficient data are given to enable the reader to form his own opinion as to which of the devices is most practicable under the prevailing conditions. Thieves of all types have their good points, speaking broadly, and it is possible to get good results with any of them, provided they are operated according to instructions and with due care. In work of this kind the advantages or disadvantages reside in the person operating the instrument rather than in the instrument used."

Apr 1, 1920

By Allan F. Smith

The Bureau of Mines studied toxic products produced by burning eight fire-resistant mines conveyor belts, a brattice cloth, and an electrical cable insulation obtained from laboratory-scale burning experiments under various air-flow conditions. Generally, CO product concentrations for most materials were noticeably higher then the NO2 and HC1 levels that were measured; also, no phosgene was detected. However, several of the fire-resistant belt samples yielded HC1 concentrations that were above the reported lethal level for 1/2 to 1-hour exposures, although these data were limited to flow conditions where air dilution effects were small; the belt materials that showed this behavior included samples of polyvinyl chloride, styrene butadiene, styrene butadiene blends, and a British neoprene which yielded the greatest amount of toxic vapor. In addition, some results are presented on the phosphoric acid concentrations that may be produced from the decomposition of ammonium dihydrogen phosphate when dispersed on a burning coalbed.

Jan 1, 1973

By Jos. R. Guiteras

The present discussion first presents data to justify the fireproofing of mine shafts. This is followed by a brief outline of fireproofing methods with examples from practice. A summary of authoritative recommendations on fire prevention concludes the discussion. Acknowledgment is made to D. J. Parker, district engineer, Mine Safety Station, Salt Lake City, Utah, for his valuable criticism of the paper. Fireproofing a mine shaft implies lining the shaft with fireproof material or rendering fireproof the material already composing the shaft lining. A brief study of the part mine shafts and shaft stations have played in disastrous end tragic underground fires furnishes convincing evidence that every possible effort to make all mine shafts fireproof is amply justified. The fire hazard in coal minus obviously is much greater than in metal mines. In this discussion the point of views is mainly that of the metal miner; it is tine opinion of the writer that all fires in metal mines are preventable.

Jan 1, 1939

By Byron E. Blair

This report describes procedures for using a high-speed camera to study blasting phenomena. Both quantitative and qualitative information can be obtained, provided that proper interpretations of the projected two-dimensional images are made. Geometrical relationships between object and image displacements are given in terms of horizontal and vertical angles of the camera optic axis with respect to the quarry face. Correction factors are given for obtaining true object displacements from image displacements in the camera film plane. The time of initial rock movement also is considered, and the control-ling factors of camera speed, scale factor, minimum increment of projection measurement, etc., are evaluated in terms of minimum time intervals. The high-speed camera and associated equipment are described, and field measurements and laboratory data analysis techniques are outlined. An analysis of a typical high-speed motion picture is made, and the application of the necessary correction factors is illustrated.

Jan 1, 1960

In connection with tin strategic minerals investigations of the Bureau of Mines and the Geological Survey under authority of the Strategic Materials Act (Public 117, 76th Cong., 1st sess.) a study is being made of tin deposits in the United States in an effort to improve the situation with respect to domestic supplies. These studies include sampling and exploration of some of the larger deposits with the objective of establishing emergency reserves, if possible to do so. Two exploration projects have been completed, and the over-all results obtained are set forth in this progress report. RESOURCES Tin was first discovered on this continent in 100 in the Temescal Mountains of what is now southern California. In the ensuing century, occurrences of tin have been reported in no less than 17 States and Alaska. Although most of these are of scientific interest only, tin-bearing veins and placers in California, Alabama, North and South Carolina, Virginia, South Dakota, Wyoming, Texas, New Mexico, and Alaska have been extensively explored, and largo sums of money have been expended in recurring attempts to exploit them.

Jan 1, 1941

By Suresh K. Bhatt, Gary L. Mowrey, Timothy R. Rehak, David K. Ingram

Coal and nonmetal mining used about 4.3 billion pounds of explosives and blasting agents during 2001 in the United States. A major part of this consumption was related to surface mining. Mine Safety and Health Administration accident data indicate that flyrock and lack of blast area security were the primary causes of blasting-related injuries in surface mining. Fatal injuries due to lack of blast area security were primarily caused by failure to clear blast area or inadequate access control to the blast area. At a coal mine, a neighbor walked into the blast area and was fatally injured. The blaster could not see the victim entering the blast area from the firing station. In another case, a passenger in a vehicle was fatally injured by flyrock because highway traffic was not monitored during the blast. In another example, a dozer operator entered a blast area due to lack of access control. Several fatalities resulted from using inadequate or no blasting shelter. A crane operator was fatally injured while standing in the open about 120 ft from the blast site. In another instance, a helper, standing about 150 ft away from the edge of a blast, was fatally injured by flyrock. In a limestone mine an equipment operator was fatally injured while guarding access roads in a pickup truck. This paper briefly describes six representative fatalities due to flyrock and lack of blast area security in coal and nonmetal mines. Several mines were visited to collect information relative to working practices aimed at mitigating blasting hazards. Salient information obtained through these visits is presented.

By E. J. Schneider

In view of the growing commercial interest In the higher boiling fractions of low-temperature tar, a study of the literature has been undertaken to obtain as many data as possible regarding the properties of possible pure constituents. The following substances have been studied: THREE-ORTHO-XYLENOL (1, 2-DIMETHYL-3-HYDROXYBENZENE) Detection By the isolation of the silver salt of 1, 2-dimethyl-3-phenoxyacetic acid.

Jan 1, 1930

This is an audience, I know, that shares my interest in a subject that is currently getting a lot of attention -the tendency of our Nation to draw increasingly on overseas supplies of certain mineral commodities, and proportionately less on domestic sources for these minerals. That we do obtain substantial quantities of some essential minerals from abroad is easy to demonstrate. That we will continue to do so in the foreseeable future is not in doubt. Uncertainty begins, however, when we try to interpret the significance of these facts. As with many phenomena, their meaning is open to a variety of interpretations.

Jan 1, 1980

By John Nagy

This circular has been prepared for the guidance of safety engineers, shot firers, and coal-mine inspectors concerning multiple blasting with short-delay (millisecond-delay) detonators. These special precautions are suggested in addition to those normally followed in blasting, as outlined in the Federal Mine Safety Codes 5 6/ and in Miners' Circular 58.7/ INTRODUCTION The use of short-delay blasting has been proposed for promoting safety and increasing the rate of production in coal mining. Ideally, short-delay blasting, as compared with equivalent single-shot blasting, reduces exposure of the shot firer to dust, fumes, and weakened roof; as compared with equivalent simultaneous blasting, it reduces roof disturbance.

Jan 1, 1959

By L. C. IlsLey

The observations made by Bureau of Mines engineers of permissible equipment installed in about 40 mines have indicated a chance for improvement in designs calling for the use of bolts , screws , studs , etc. , especially with respect to bolt sizes and protection from mechanical injury .

May 1, 1931

By W. J. Johnson

This report presents the Phase I progress in the development of a Radar Coal Thickness Sensor (RCTS) being conducted by Boeing Aerospace and Electronics for the Bureau of Mines. A method is developed for measuring both the dielectric constant and depth of the coal shale interface using a modified UHF network analyzer and antennas in proximity to the surface of the coal. Both bistatic and monostatic systems, are compared. The algorithm technique uses synthetic range gating for clutter rejection and full polarimetric scattering matrix techniques to extract the dielectric constant and depth to sub-wavelength accuracies. Tests were run both in the lab and in a coal mine to build an error budget and demonstrate a validation of the model. The development of a prototype radar suitable for coal mine robotics is specified.

Jan 1, 1990

By Charles E. Munroe

"It has been recently learned that certain foreign manufacturers are offering far importation into this country detonators at greatly reduced prices, some of these detonators being of such low grade (No.4), that their use would greatly increase the dangers in blasting.Detonators and electric detonators are used in initiating the explosion of the various high explosives that are now so extensively employed in a great variety of mining operations. Originally a large number of different grades (or ""strengths"") of detonators and electric detonators were marketed, the grade number indicating the weight of the charge of fulminating material contained in the copper case of the detonator. As late as 1914, a report of the Bureau of Mines (Bulletin 80, A primer an explosives for metal miners) shows that grades Nos. 3, 4, 5, 6, 7, and 8, containing from 0.54 to 2.00 grams each, were being offered for use. However, the writer bad observed as early as 1896, when the more insensitive types of explosives like nitro-substitution explosives began to be introduced for use in mining and other blasting operations, that use of a high-grade detonator was essential to insure certainty of discharge."

Mar 1, 1921

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

RECOMMENDATIONS FOR FURTHER WORK Based on the development effort and full-scale tests conducted during this program, a number of technical areas for future research and development have been identified. Further work in these areas would help to improve the reliability, speed of operation and efficiency of the remote sealing system. Recommendations for future work are summarized as follows 1. Development of an Inert Gas Generator For the sake of expediency in conducting the field test program, fresh air was used as the fluidizing medium for the fly ash. However, in an actual mine fire application the use of fresh air is likely to be prohibited. An inert gas, such as nitrogen, carbon dioxide or air containing less than 8 percent oxygen would be required. Using combustion as a means of reducing the oxygen content of air appears to be an attractive solution to the generation of the high flow rates of gas required (2500 to 5000 scfm). Such an inert gas generator would serve a dual purpose for the overall fire extinguishing operation. First, it would provide the inert gas for fluidizing the fly ash. Second, it could be used for inerting the fire area after the seals had been placed, thereby reducing the time required to extinguish the fire. It is recommended that the Bureau undertake a program to develop a field-operable, inert gas generator to satisfy these two requirements. 2. Development of a Field-Operable Sonar Initial Probing System A first stage prototype of a sonar initial probing system was developed during this present program. The results obtained with

Jan 1, 1973

By F. J. Gallagher

Some serious fires have occurred in bituminous-coal mines because of short circuits on direct-current power systems that do not have adequate circuit-breaker protection. The writer's observation of circuit-breaker installations in numerous coal mines leads to the conclusion that many persons am not properly informed as to the true functions, limitations, and operation of circuit breakers. Faulty protection results in fire hazards that endanger lives and property. Proper circuit-breaker protection would greatly minimize or, in many instances, eliminate the hazards; moreover, many operating advantages of proper application of modern circuit breakers would be gained. The purpose of this circular is to show why fire hazards exist in many mines despite the use of circuit breakers and how, the hazards may be overcome. A method is given for determining whether additional circuit-breaker, protection is required for a specific 250/275-volt direct-current distribution system, and, if so, the approximate locations and capacities of the required supplemental breakers.

Jan 1, 1951

By Byron M. Bird

"The prevailing practice of washing unsized coal, 1/2-inch and finer, to 1/8-inch and finer, on a table is subject to certain limitations which are commonly overlooked. In some instances good results are obtained by this method, but often the opposite is true and the efficiency of the washing operation is low. Although the separation taking place on a concentrating table is not fully understood, the actual distribution of particles of various sizes and specific gravities was determined a number of years ago by ore-dressing investigators. Hence this paper consists of an analysis of an old problem by new methods. The experimental data on which the discussion is based were obtained in the course of coal-washing investigations conducted by the U. S. Bureau of Mines at the Northwest Experiment Station in cooperation with the University of Washington and with certain coal operator: of that State.Experimental WorkThe general method of study has been to take a large number of zonal products from the table, and separate them according to specific gravity and size into their component parts. The table used is one of the standard commercial sizes with a diagonal deck. The coal to be washed is split into representative portions, which are stored in separate bins. One portion is used for ""timing as"" the table; the products are collected continuously in the same turned to the feed bin, and thus a closed circuit is completed. When the despite conditions on the table are obtained, coal is fed from one of the re. After the table is operating smoothly the entire product is minute; such a sample is sufficiently large to represent accurately the work of the table and at the same time to minimize the effect of beginning at the end next to the head motion, separate samples are made for each foot along the edge of the deck."

Jun 1, 1926

By Raja V. Rarnani, Robert L. Frantz

"Co-Directors, Generic Mineral Technology Center for Respirable DustEarly in the 1980s, the U.S. Bureau of Mines initiated the concept of the Generic Center, incorporating it into its mining research program, and in 1983, the Generic Mineral Technology Center for Respirable Dust was established. The Generic Center concept was first envisioned by the U.S. Bureau of Mines as a way to bring together the various different scientific, engineering and medical research interests in the respirable dust area to effect a coordinated and efficient organization for advancing knowledge in that field. The result was a combination of the collective talents and skills of more than 100 scientists, engineers, medical personnel and graduate students, through the formation of a consortium of five major research universities, including medical facilities, to perform respirable dust research. The Generic Mineral Technology Center for Respirable Dust consortium comprises The Pennsylvania State University (with its Hershey Medical Center) and West Virginia University (with its Medical Center) as the lead universities and the University of Minnesota, Massachusetts Institute of Technology and Michigan Technological University as affiliates.Although respirable dust-related disease remains the nation's worst industrial hazard, the fundamental understanding of all aspects of respirable dust associated with the mining and milling industries, including the interaction of dust and lungs, has grown significantly over the past near-decade toward the larger effort to reduce the incidence and severity of disease caused by respirable dust. Continued progress toward making the mine work environment cleaner and healthier remains the immediate objective of the Respirable Dust Center.The Respirable Dust Center's research program and technology transfer activities, described in this paper, exemplify the Generic Center concept first envisioned by the U.S. Bureau of Mines. Interdisciplinary and interactive studies continue to result in significant progress toward making mine atmospheres cleaner and healthier."

Jan 1, 1995