Search Documents

By G. L. Humphrey

Although thermodynamic data for ferrous oxide are among the most important in extractive metallurgy, adequate values have not been available until quite recently. The older data suffered not only from the usual experimental difficulties but especially from lack of the knowledge that ferrous oxide of stoichiometrical composition does not exist as a single, thermodynamically stable crystalline phase under any circumstances. This paper reports new experimental data on the heat of formation of ferrous oxide by two methods (combustion calorimetry and solution calorimetry), employing material of unequivocal composition. The results are compared with values obtained from data for the hydrogen reduction, carbon monoxide reduction, and disproportionation reactions of ferrous oxide, and a best value is selected. A table of heat and free energy of formation values of ferrous oxide to 2,000°K is given. These values are combined with available data for water, carbon monoxide, and carbon dioxide to obtain theoretical heats and free energies of reduction corresponding to the selected heat of formation. Hydrogen and carbon monoxide reduction equilibria are compared, and the differences in trend with temperature and the percentage utilization of the reductants are considered.

Jan 1, 1952

By C. F. Davidson

The Bureau of Mines studied the extraction of lithium from lithium-containing clays by chlorination with hydrogen chloride (HC1). In bench-scale laboratory investigations, HC1-H20 mixtures were used to selectively chlorinate lithium, but not calcium or magnesium, in lithium-containing clays. The addition of calcium carbonate to the clay was found to improve the lithium recovery. Reaction conditions found to affect the lithium recovery were ratio of clay to carbonate, reaction temperature, and HC1 concentration. The best conditions for selective chlorination of the lithium were 2:1 clay-carbonate, 750° C, and 20 wt-pct HC1. The experimental results and trends in lithium extraction are explained using thermodynamic relationships.

Jan 1, 1981

By L. D. Wyant

That natural gas-gasoline can be used to advantage as a refrigerant is suggested by the fact that the "make" tanks and other parts of the equipment of gasoline plants frequently become coated with frost. The experiments reported in this paper confirm this assumption and indicate that volatile gasoline can be use used to advantage in many refrigerating plants. The Bureau of Mines is making a study of wax distillates in order to find out why satisfactory lubricating oils and waxes can be made easily from certain crude oils and only with difficulty from others. In the commercial distillation of crude petroleum it is customary to separate the distillates into the following groups: (A) Gasolines and naphthas, (B) Kerosenes, (C) Gas oil, and (D) Wax distillate (consisting mostly of light lubricating oil together with small amounts of paraffin Wax).

Jan 1, 1923

By Dean E. Bluman

The Bureau of Mines investigated the convective heat transfer coefficients for recirculated suspensions of 30-micron glass beads in inert gas. Coefficients for the suspensions were not significantly higher than coefficients for the pure gas. Reynolds numbers of the suspensions were 20,000 to 35,000; solids loadings ranged from 0.0 to 0.7 pound per pound of gas. Comparison of the results with published data showed the direction of heat flow to have no effect at the test conditions.

Jan 1, 1967

By M. M. Tilman

The Bureau of Mines conducted research to determine the feasibility of strengthening experimental magnesium-base sheet alloys by strain softening induced by controlled cold rolling followed by selective heat treatment. Relatively small alloying additions having potential for producing strain softening were selected from metals that are readily avail-able. Tensile properties comparable to minimum properties of the most commonly used magnesium-base sheet alloy AZ31B, in the H24 condition (strain-hardened and partially annealed), were obtained in an Mg-IMM (mischmetal)-O.5Mn alloy after strain-softening rolling followed by heat treatment. Tensile properties of the experimental alloys in certain conditions are also compared with minimum tensile properties of other standard magnesium sheet alloys. Incidental to the principal objectives, apparent superplastic behavior was observed in three experimental magnesium-base alloys containing MM, MM plus manganese, and MM plus zirconium.

Jan 1, 1985

By P. D. Kovscek

The Bureau of Mines equipped a longwall shearer with a water-jet-assisted mechanical cutting system to determine the effect of the high-pressure sprays on machine performance, airborne dust levels generated, and size of particles formed. Testing was conducted on a simu-lated coal block (coalcrete) while cutting at a water pressure of 190 psi and at water-jet-assisted pressures ranging from 1,000 to 6,000 psi. The shearer motor energy used by the shearer while cutting coalcrete was determined for each cutting condition. Results indicate that the motor energy required by the shearer for each ton of material cut did not vary significantly as the water pressure was increased. Results of dust measurements recorded near the cutting drum indicate that at water pressures above 3,000 psi, dust reductions up to 85 pct were achieved com-pared with cutting with conventional sprays. Analysis of the particle size distribution during cutting showed that increasing the water pres-sure resulted in increased median particle size. In light of these results, various mechanisms for water-jet-assisted cutting are discussed.

Jan 1, 1986

By John C. Machisak

INJURY DATA and experience at coal mines in the United States for 1957 are presented in this bulletin under the following general sections: (A) General injury experience: Tables 1-6: Current data on number of fatal and nonfatal injuries, frequency and severity rates, and average severity. (B) Selected injury experience: Tables 7-36: Current data on causes of injuries, distribution of injuries by part of body injured, days of disability, extent of hand and machine loading, experience by employ¬ment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation's coal mines. (C) Injury experience, by States: Tables 37-41: Data on injuries, injury rates, employment, causes of injuries, and severity rates. (D) Major disasters: Table 42: Data on major disasters from 1948 to 1957. A major disaster is defined as a single accident in which, or as a result of which, five persons or more are killed instantly or die at any time thereafter. (E) Historical coal-mine-fatality experience: Tables 43-47: Data on fatalities and their causes at bituminous-coal, lignite, and anthracite mines from the earliest records through 1957.

Jan 1, 1960

By Douglas F. Scott

Researchers from the U.S. Bureau of Mines conducted geologic investigations in an area of the Lucky Friday Mine, Mullan, ID, that included the 5300-107 demonstration stope using underhand longwall cut-and-fill mining. Structural analysis of the area suggested that argillite beds form planes of weakness between blocks of brittle quartzite, and energy may be released along these planes and at the junctures of fractures. Mapping argillite beds and fractures in the stope wall rock showed that the planes of these features diverged and that their attitudes corresponded from one wall to the other. Seismic analysis showed that the number and location of events varied as each cut was mined, with about 39 pct of the total number of events occurring above the cut being mined, about 54 pct below, and 7 pct at the same elevation.

Jan 1, 2010

By Sathit Tandanand

This Bureau of Mines report describes the method of obtaining a strength index for rock drillability, particularly for percussion drills. The original Protodyakonov method has been slightly modified, essentially to eliminate uncertainties in the measurement of the volume of fines, and to avoid conjecture in selecting the representative value as the strength coefficient. A theoretical consideration of the relevant parameters in the method was extended from a comminution theory, and hence the meaningful value was obtained experimentally by plotting the ratio of the number of drops and the volume of fines against the number of drops. The minimum ratio of the number of drops to the volume of fines in the plot was selected as the coefficient of rock strength. The modified method of obtaining the strength coefficient preserves the original Protodyakonov test apparatus and the merit of simplicity of the test procedure. The modified coefficient of rock strength shows its usefulness in predicting penetration rates with greater reliability than other mechanical properties. Consequently, the drillability curves were drawn using the modified coefficient of rock strength as the parameter for penetration rate prediction in the field.

Jan 1, 1975

By Lindsly. Ben E.

"The recovery or partial recovery of the oil remaining in oil sands after the usual methods of production have become unprofitable is perhaps the greatest problem in the petroleum industry today. The amount of this oil remaining in the sand is variously estimated by those familiar with the subject to be 25 to 90 per cent of the original content.2Lewis3 states, ""The estimate of 80 to 90 per cent of the oil left underground does not seem incredible.""It is estimated by the writer that approximately 91 per cent of the oil originally held in the Elliott pool, was still in the formation on January 1, 1924, and that it would take at least 12 years, at the 1923 rate of production, to further reduce this quantity by one per cent of the original content.The progress made in the oil industry during the past few years relative to the prevention of evaporation losses; to improvement in cracking processes, whereby the gasoline yield from many crudes has been doubled and trebled; to the increased recovery of gasoline from natural gas; and many other developments, remarkable as they are, can be applied only to that comparatively small portion of petroleum products which are raised to the surface. A device or process which would cut development costs to one-half would probably result in a much smaller profit to the oil industry, than the profit derived from an additional 10 per cent recovery of the total amount of oil in a pool. Various methods have been used and many others proposed, for the increase of oil recovery from normally depleted sands.In France, oil sands are being mined by means of shafts and galleries. In other places, notably the Bradford, Pennsylvania field, the yield has been increased by means of water flooding, wherein water is introduced into the sand to displace oil, and drive it to producing wells."

Oct 1, 1926

By Richard W. Watson

Card-gap and projectile impact sensitivity data are presented for a wide variety of explosive compositions tested at the Bureau of Mines in more or less standard test geometries. The results of both tests are in good agreement in that they provide the same sensitivity ordering for different subclasses of explosives. Least sensitive were homogeneous liquids that did not exhibit a tendency to undergo low-velocity detonation, ammonium nitrate-fuel oil, and most cast military explosives. Of intermediate sensitivity were pressed and powdered military explosives, cast pentolite, permissible and non- permissible water-based explosives, and one commercial two-component explosive. The most sensitive were permissible and nonpermissible dynamites and explosives susceptible to low-velocity detonation.

Jan 1, 1973

By Jr. Frost

Helium used as a tracer gas in petroleum reservoirs continues to show great promise as a new tool for the oil and gas industry, according to tests conducted jointly by the Bureau of Nines and The Pure Oil Co. in-the Cabin Creek field, Boone and Kanawha Counties, W. Va. Helium, when used as a, tracer gas, is mixed with natural gas being injected into a reservoir for secondary recovery of oil, recycling, pressure-maintenance, or other purposes. Three separate experimental helium tracer-gas tests were run in the Cabin Creek, W. Va., field, wherein helium was added as a tracer to the natural gas that was being injected into the oil-bearing Berea sandstone. The results obtained in each test permitted determining the direction and rate of travel of the injected gas, calculating the volume of injected gas in the gas produced at the various wells, and determining the nature of the transition from natural gas to injected gas during a gas-injection program. Data were obtained on the effects obtained from waves of injected gab containing 1 percent and containing 5 percent helium and from a wave of essentially pure helium injected into the formation.

Jan 1, 1950

By Donald W. Scott

Chemical thermodynamic properties for the ideal gas state from 0 to 1500 K are tabulated for all of the alkane hydrocarbons through C10. These properties are based on correlations of the extant data for the entropy, vapor heat capacity, and enthalpy of formation of individual alkanes and the equilibrium constants of alkane isomerization reactions.

Jan 1, 1974

By Alvin Kaufman

Geothermal plants are competitive with conventional units. A geothermal plant can produce electric energy for 6.70 mills per kwhr, compared with 6.96 mills for coal, 6.74 mills for oil, and 7.04 mills for gas. These costs include fixed and variable charges. Potential for geothermal power exists in the Western United States, Alaska, and possibly Hawaii. Assuming that the current downward trend in cost per kilowatt of coal will cease and that the relative cost of gas and oil, already trending upward, may rise considerably more, geothermal energy will be utilized where available, in producing electric energy. It will be used in California first because it is directly competitive with gas-and oil-fired installations there. A long-term appraisal is difficult because little is known about the sources of geothermal power and the electric generating capacity which the steam fields will support. However, a market for geothermal steam-generated electricity exists within the Western States.

Jan 1, 1964

By Alvin Kaufman

Geothermal plants are competitive with conventional units. A geothermal plant can produce electric energy for 6.70 mills per kwhr, compared with 6.96 mills for coal, 6.74 mills for oil, and 7.04 mills for gas. These costs include fixed and variable charges. Potential for geothermal power exists in the Western United States, Alaska, and possibly Hawaii. Assuming that the current downward trend in cost per kilowatt of coal will cease and that the relative cost of gas and oil, already trending upward, may rise considerably more, geothermal energy will be utilized where available, in producing electric energy. It will be used in California first because it is directly competitive with gas-and oil-fired installations there. A long-term appraisal is difficult because little is known about the sources of geothermal power and the electric generating capacity which the steam fields will support. However, a market for geothermal steam-generated electricity exists within the Western States.

Jan 1, 1964

By L. Crocker

The Bureau of Mines investigated processes for recovering a marketable lithium product from the montmorillonite-type clays of the McDermitt caldera. The clay deposit, located on the Nevada-Oregon border, is estimated to contain over 3 million short tons of lithium. Limestone-gypsum roasting and selective chlorination proved most successful for extracting lithium from the clays; 80-pct Li recovery was achieved using either technique. With both processes, lithium silicate in the clay was converted to a water-soluble compound-either lithium sulfate or lithium chloride. The lithium was then recovered as a carbonate by water leaching the calcine, concentrating the leach solution by evaporation, and precipitating the lithium with soda ash. The operating costs for the limestone-gypsum roast process were estimated at $2.02/lb Li2C03; selective chlorination operating costs were estimated at $3.85/1b Li2C03. The current selling price of Li2C03 is about $1.50/lb. A detailed flowsheet, material balance, and process evaluation are presented for the limestone-gypsum roast process. In addition, lithium reserves and resources are discussed and the McDermitt clays are described.

Jan 1, 1988

By R. V. Lundquist, H. Leitch

Sodium aluminate is the principal aluminum compound formed in the sinters prepared by the lime - soda sinter process for recovering aluminum from silicate source materials . The properties and characteristics of this compound were studied to improve the efficiency of the process . Crystalline sodium aluminate was prepared by sintering stoichiometric quantities of soda ash and calcined alumina for 1 hour at 1,250 ° C. The extent of aluminum extraction from sodium aluminate was determined in water and in solutions of NaOH and Na₂ CO3 . Nearly complete extraction of aluminum from sodium aluminate was achieved only in solutions containing free NaOH in excess of that supplied by the salt through hydrolysis . About 42.2 to 68.8 percent of the aluminum was extracted in water or in solutions of Na₂ CO . The precipitation of alumina trihydrate from sodium aluminate solutions was shown to be part of a continuous , reversible reaction according to the equation Al (OH ) A1 (OH )3 + OHThe reverse reaction dissolves alumina trihydrate in NaOH solutions to produce sodium aluminate . Approximate equilibrium concentrations were determined for the reaction at 30° , 50 ° , and 70 ° C. False apparent equilibrium conditions for the dissolution reaction appear when only a small excess of alumina trihydrate is present in the NaOH solutions . A large excess of alumina trihydrate must be present before the true equilibrium point is assured . The engineering significance of the data is summarized , showing controls that should be exercised for a successful and efficient process .

Jan 1, 1964

By A. B. Cecala

The Bureau of Mines has developed a pallet loading dust control system designed to lower the dust exposure of workers during the bag stacking process at mineral processing facilities. The system makes bag stacking much easier because the pallet height remains constant throughout the entire bag stacking cycle through the use of a hydraulic lift table. The system uses a push-pull ventilation technique to capture the dust generated during bag stacking. A low-volume, high-velocity blower system operating at approximately 150 cfm blows a stream of air over the top layer of bags on the pallet. The blower system is composed of two 3-in air jets (approximately 1,200-ftjmin velocity) directed toward an exhaust system on the opposite side of the pallet. As these air jets travel across the pallet, they entrain the dust generated during bag stacking. The exhaust ventilation system pulls approximately 2,500 cfm of air and dust through the exhaust hood. This exhaust air can then be dumped into a baghouse ventilation system, or filtered before being discharged outside the mill. During a laboratory evaluation, a 70-pct dust reduction was recorded for the bag stacker. The system was then evaluated in an actual working environment. The first field evaluation was performed at a silica sand operation in which one worker performed the entire loading and bag stacking process. This worker's dust exposure was lowered 76 pet when using the new pallet loading system. The second field evaluation showed only moderate dust reduction, but this was mainly attributed to an overriding problem associated with background dust and the cleanliness of the bags. From both the ergonomic and production standpoint, the system was well received by both the workforce and plant management.

Jan 1, 1988

By A. L. Engel

In recent investigations of chloride Volatilization of gold at the Reno Station, it was found that the addition of small amounts of copper and NaCl to the charge brought about improved volatilization of the gold. The investigations described in this report were concerned with the recovery, in an aqueous medium, of fumes from chloride volatilization of gold. It was attempted to discover a suitable aqueous medium that would permit absorption, solution, or precipitation of all the volatilized gold immediately upon contact with the medium. A simple laboratory apparatus was employed to produce fumes by volatilization. To this furnace was attached an absorption train consisting of a series of chambers containing the aqueous medium, through which the fumes were drawn by suction. A satisfactory synthetic ore that contained metallic, gold in a quartz-matrix was made and utilized, enough. gold being present in a' small amount of material to permit an accurate, metallurgical balance of the volatized values' to be obtained in all the experiments.

Jan 1, 1949

By C. E. Augustine, B. A. Landry, P. Nicholls

"Wien bituminous coal is burned in a hand-fired up-draft boiler used for heating purposes it has a decided tendency to produce smoke. A design of furnace and a method of firing and attendance that are satisfactory for fuels low in volatile matter, as anthracite or coke, are not necessarily Satisfactory for bituminous coals. It is therefore becoming common practice to use a special design of furnace for bituminous coals, in order to facilitate the combustion of the volatile matter and soot. This is done by (1) providing a larger combustion space to give more time for the combustion, (2) construction that will produce a better mixing of the gases and secondary air supplied over the fuel bed, or (3) keeping the gases at a higher temperature by preheating the secondary air, as may be done by surrounding them with refractory surfaces, or causing them to pass through a fuel bed of hot coke. A furnace may be built to use any or all of these methods of smoke prevention.In Bureau of Mines Technical Paper 303, Blizard5 and others give tests on a large heating boiler when burning coke, anthracite, and bituminous coal. Certair alternative furnace arrangements were used, but there was no material change in the furnace design for the various fuels. Since that time the manufacturer has made modifications in design to adapt it for use of bituminous coal, and additional tests have been made to determine how this change affected the production of smoke and the efficiency of the boiler."

Jun 1, 1929