Search Documents

By W. H. Young

The thickness of the coal seam is one of the more important items influencing the productivity and general overall efficiency of operation 1 of a coal mine. The average thickness of coal seams mined in the United States decreased 2 inches between 1950 and 1955 to an average of 62 inches, which also is 3 inches less than the 65 inches in 1945. The decrease in thickness is due partly to the increased production from strip mines with thinner seams and partly to the increased percentage of total production at underground mines in certain States having thinner seams. The thickness of seams at auger mines was measured for the first time in 1955 and was 53 inches. Though bituminous coal and lignite is mined today from seams of exceedingly variable thickness -less than 2 feet to ore than 50 feet -a large majority of the production, 65 percent in 1955, came from seams 3 to 6 feet thick. This is not surprising since the coal seam of moderate thickness presents the least mining difficulties.

Jan 1, 1957

By H. Stuart Auvil

Twelve samples of run-of-oven coke were taken at coke plants in the United States and Canada. Sampling procedure was directed toward obtaining the highest possible degree of uniformity in the gross samples, so that variations in results caused by sampling variations were at a practical minimum. Under these conditions the standard deviation of the screen analysis test on 500-pound samples is found to range from 1.2 percent for the 1-inch screen to 4.5 percent for the 5-inch screen. At present, the A.S.T.H. standard method of test requires that results be reported to the nearest 0.1 percent. This implies a higher than actual degree of precision, and revision of the report required by the method is suggested. Much larger Samples than are generally tested are required to reduce normal testing errors to a point where they are not appreciable fractions of the total variations found in a smoothly operating plant. For example, it is deduced that over 100,000 pounds of coke must be screened to determine if ordinary day-to-day variations in screen analysis have appreciable effects on the performance of a blast furnace.

Jan 1, 1950

By K. O. Bennington

The thermodynamic properties of aegirine, of composition [(Na0.869Fe30+7362 Fe20+16Mn0.03Ca0.1121)(A10.141Sil 9738)(06)], were experimentally determined at the Bureau of Mines as part of its efforts to advance minerals technology. The standard enthalpy of formation determined by hydrofluoric acid solution calorimetry is AHf298 = -641.12±0.73 kcal/mol. The standard enthalpy of formation from the oxides is AH298 = -37.136±0.509 kcal/mol. Low-temperature heat capacities were determined by adiabatic calorimetry from 19.1 to 304.6 K. The derived standard entropy is S298 = 38.03±0.14 cal/mol?K. The heat capacity was measured over the range 348 to 1,198 K by differential scanning calorimetry. These experimentally determined data were combined with data from the litera¬ture to calculate the Gibbs energies of formation and equilibrium constants of form¬ation over the temperature range of the measurements. Standard enthalpies of forma¬tion are given as functions of temperature. The standard Gibbs energy of formation at 298.15 K is AGf298 = -600.36 kcal/mol.

Jan 1, 1984

By F. E. Joyce, Charles Prasky

This report describes the response to high- temperature sulfatization of a variety of manganese minerals and companion compounds which may occur either as a principal component or as a gangue material in low- grade manganese deposits . Fourteen manganese samples representing oxide , carbonate , and silicate minerals as well as seven compounds which might occur as gangue with manganese minerals were tested batchwise in a bench- scale apparatus under conditions which would be favorable for the sulfatization of manganese . The manganese minerals substantiated thermodynamic predictions and responded to sulfatization but to varying degrees . The gangue materials , MgO , MgCO,, CaO , and CaCO3 , were sulfatized readily in contrast to the iron oxides and the aluminacontaining material which were not .

Jan 1, 1964

By R. G. Warncke, D. Harrington

"INTRODUCTION The use of black blasting powder as an explosive in coal mines has long been recognized as hazardous and has been responsible for many of the worst disasters in American coal mines. One of the most pressing of the numerous problems confronting the Bureau of Mines, upon its creation in 1910 was to determine methods that would lessen the hazards created by the use of explosives in coal mines. The Bureau continued the study begun by the Technologic Branch of the Geological Survey as to the nature of explosives and made numerous tests to determine types of explosives suitable for blasting in coal mines. The Bureau has tested and approved hundreds of types of explosives and has disseminated information on methods and conditions for use underground to make them permissible as to safety. The Bureau of Mines has encouraged the use of permissible explosives for coal-mine blasting, and its experts both in the laboratory and in the field believe that the use of black blasting powder in any form (granular or pellet) is hazardous in any underground coal mine. Despite the information published at various times and innumerous ways and the general knowledge of the hazards that the use of black blasting powder in any form creates in the blasting of coal, the coal mines in the United States, during 1947 used approximately 34 million pounds of black blasting powder (granular or pellet), or approximately 11.8 percent of the total quantity of explosives used by the coal-mining industry.Many coal mines of the United States, for various and sundry reasons, probably will continue the use of black blasting powder, and this circular has been written for the benefit of such users, not that any suggested method or methods will make the use of this explosive safe, but it has been found that methods and conditions of use of black blasting powder can be improved so as to lessen, though not eliminate, the hazards created by its use."

Mar 1, 1949

By J. L. Shultz

Mass spectrometric analyses were obtained for naphthalene and anthracene oils, heavy creosote, and three fractions of a pitch. The average molecular weight, aromaticity, and mean structural unit were determined for each fraction. The investigation of these fractions of coal tar has resulted in semiquantitative data for 38 structural types and carbon number distribution data for their alkyl derivatives. The molecular weights of 10 of these structural types indicate ring systems not previously reported in products from high-temperature carbonization of coal. Two of these structures are poly-nuclear aromatic hydrocarbons, two are oxygen-containing compounds, one contains sulfur, and five are nitrogen-containing compounds.

Jan 1, 1967

By Juel H. Stears

Research was done to determine if a hydraulically operated penetrometer developed by the Bureau of Mines could be used to estimate the roof-bolt anchorage capacity of mine roof rock. Tests were conducted both in the laboratory using cement cylinders and underground in shale rock. Hardness readings were measured by the penetrometer around the periphery of the bolt holes at the anchorage horizon. Roof bolts Nere then installed and subjected to an anchorage test. The results showed that the penetrometer readings could be used to determine the optimum stratum for roof-bolt anchorage but could not be used to make an accurate estimate of the anchorage capacity.

Jan 1, 1965

By George S. Koch

A mathematical simulation model has been devised to guide the layout of underground mine workings, drill stations, and drill holes that are established in order to search for tabular ore bodies. Developed and tested for elliptical ore shoots in fissure veins in the Galena mine, Coeur d'Alene district, Idaho, the model can also be applied to ore bodies contained within sedimentary beds (for instance, many types of uranium, copper, and gold ore bodies) or other tabular structures. Programed for a time-shared digital computer, the model contains both stochastic and deterministic variables. Stochastic or natural variables include the number of ore shoots and their sizes, orientations, locations, and values. Deterministic or controllable variables include (1) locations and costs of workings; (2) drill-station locations and costs; and (3) drill hole azimuths, inclinations, lengths, and deflections, if any. For various assumptions about the stochastic variables, the model is run while the controllable variables are changed deliberately. Thus, layouts are devised to determine the percentages of the total number of assumed ore shoots found at different costs. In order to choose among the various layouts, cost-effectiveness measures are calculated.

Jan 1, 1974

By R. W. METCALF, A. G. Charles, F. M. SHORE

To furnish the information frequently requested by producers and suppliers as to the fuel requirements of the Federal Government , the Bureau of Mines , with the cooperation of the consuming departments and establishments , has collected the data herein , showing the Government's fuel consumption during the fiscal year ended June 30 , 1930. The following tables show the quantities and kinds of fuels consumed by the Federal Government in each of its departments and their principal branches , in each State , and in Alaska , Hawaii , Panama Canal Zone , Porto Rico , and the Virgin Islands . The separate departments and establishments were asked to supply information for each Federal building or other plant and , as to vessel fuel , the amount loaded at each port of supply . Fuels consumed in internal combustion engines are not included . The report does not include fuels used by Post Offices of the fourth class , since their fuels are not purchased by the Federal Government but are covered by an allowance in each case for light and heat . In some cases the data supplied represent receipts , which are approximately equivalent to consumption . The present study is believed to be the first effort to bring together the data representing the Government's requirements for the various fuels which it consumes . Figures showing the coal consumed by the Federal Government were gathered for the year 1922. These data are shown in an article by O. P. Hood and R. H. Kudlich of the Bureau of Mines , contributed as a chapter to " Industrial Coal ; Purchase , Delivery and Storage , " published by the American Engineering Council . The figures of coal consumption presented herewith are approximately comparable with those published for 1922 , a relatively small difference being due to the fact that the 1922 figures include the Philippine Islands and all other territory in which any coal was consumed by the Government . At the present time , the only data on Government fuel consumption that are published regularly are those compiled by E. B. Swanson , chief economist of the petroleum economics division of the Bureau of Mines . These are published annually by the Bureau of Mines in " Sources and Distribution of Major Petroleum Products , Atlantic Coast States , " and by the bureau in cooperation with the American Petroleum Institute in the annual " National Survey of Fuel Oil Distribution . " It is believed that the data herewith will prove of interest and value to the fuel industries as well as to Government consumers and that it will also afford a basis for measuring future trends in the use of the various fuels by the Federal Government . Figures showing the quantities of the various kinds of fuels consumed by each of the executive departments and independent establishments , are given in Table 1. It should be noted that when one organization procures and delivers fuel to be consumed by other branches

Apr 1, 1932

By Eric B. Sansone

The Federal Coal Mine Health and Safety Act of 1969 requires coal mine operators to sample accurately the amount of respirable dust in the mine atmosphere. A technique approved for such sampling employs a 10 mm nylon cyclone followed by a membrane filter (nominal pore size ????= 5 µm) and a pump. The pump is required to provide a flow rate of 2.0 ± 0.1 liters per minute. Calibrations have yielded a range of flow rates (1.4 to 2.8 1pm) at which the cyclone should be operated to remove the non-respirable portion of the dust. The purpose of this project was to evaluate the performance of the 10 mm nylon cyclone at flow rates of 1.8 and 2.0 1pm using a polydisperse coal dust aerosol. The penetration characteristics of the cyclone were to be compared to the United States Atomic Energy Commission's respirable dust standard. The effect of relative humidity on cyclone penetration characteristics was also to be observed.

Jan 1, 1973

By Helen E. Edwards

The Bureau of Mines is engaged in a systematic evaluation of the thermodynamic properties of combustion gases. These studies are designed to provide basic thermodynamic information of high accuracy facilitating the theoretical study of flame and combustion phenomena. This report is the third of a series3/ presenting results of the study for particular fuel-oxidant systems. The equilibrium composition of the products of combustion and the adiabatic flame temperatures of specified oxyacetylene systems have been computed.

Jan 1, 1953

By John Ward Smith, Neil B. Young

Shale specific - gravity to oil - yield relationships were developed for black shales of the New Albany Formation of Kentucky from data collected on core samples representing the complete section of the formation in three counties . Linear equations for estimating oil yield from measured specific gravity and for estimating specific gravity from measured oil yield were shown to be applicable within small error limits to all the sites tested . Variation in pyrite content is the largest source of error .

Jan 1, 1964

By H. W. Davis, W. W. Adams, O. E. Kiessling

"Current economic problems frequently have focused attention upon the lack of adequate quantitative information indicating the relationship between human effort and output in various branches of the mineral industry. With the exception of complete records covering coal mining, only scattered information on the units of human energy required to produce a unit of raw material is available for most of the important industrial minerals. Fortunately a virtually complete statistical record is available covering this phase of the iron-ore mining industry.For many years iron-ore mining companies, whose interest in safety work is well-known, have reported annual data on employment to be used in the compilation of accident statistics. These data on hours of labor and other detailed employment information have been correlated with the statistics on production also reported annually by producers. The outstanding trends shown by this composite record for the 10-year period 1923-32 are included in the following discussion, supplemented by a summary table that presents the principal statistical background of the study. 5The substantial reduction in the number of men needed to produce the annual iron-ore requirements of the United States, as shown strikingly in the graphs, illustrates that in iron-ore production improvements in technology have been consistently winning a battle over the difficulties of nature. In 1923, for example, 41,294 men working 107,551,244 hours were required to produce 69,351,442 gross tons of merchantable ore, equivalent to an average output of 0.645 ton per man-hour. In 1929, however, only 30,763 men working 77,111,686 hours 'zero required to produce 73,027,720 tons of merchantable ore, equivalent to an average output of 0.947 ton per man-hour. Thus, from 1923 to 1929 the average number of men working decreased 25.5 percent and the total man-hours worked 28.3 percent, while the average output per man-hour increased 46.8 percent and total merchantable ore production 5.3 percent."

Feb 1, 1935

By G. V. Sullivan

This report summarizes the results of a preliminary study concerning manganese extraction from low-grade dolomitic materials from the Philipsburg district in Montana by the Dean-Leute ammonium carbamate process. Studies were made to determine the relationship between the variables involved in treating these materials by a roast-leach process and the amount of manganese extracted. The variables studied were the roast temperature, the roast particle size, the molar ratio of NH3 to CO2 in the leach solution, the liquid-solid ratio in leaching, the leach time, and the size of the particles being leached. The roast-leach studies were statistically designed, and the experimental results were evaluated by an analysis of variance.

Jan 1, 1962

By J. R. Long

The Federal Bureau of Mines has pioneered the work of preparing ductile titanium on a large scale and has also determined the basic properties of this new and most interesting metal. A number of reports (1, 2, 3: 4, 5) have al-ready been published, and considerable interest has been aroused in a number of industrial and research laboratories. Some of these laboratories have also published results of their work on the pure metal. Although the properties of titanium itself are quite promising, it is apparent that considerable improvement may be expected by alloying titanium with other metals. That is, pure metals in general have shown relatively large improvements in properties when alloyed with other metals and titanium is not considered to be an exception to the rule. Therefore, the emphasis of the investigations now under way in the Federal Bureau of Mines Laboratories has been placed on the study of the alloys of titanium, particularly the titanium-rich alloys. While the main interest is in the properties of such alloys, proper direction and evaluation of the work require at least a rough outline of the phase boundaries of the alloy systems involved.

Jan 1, 1949

By Phyllis Lyday

Mining did not contribute significantly to the economy of Benin, a small country on the coast of West Africa, during 1978-79. During these years, Benin continued to be rated by the United Nations as one of the 25 least developed countries in the world; its gross domestic product was under $200 3 per person per year. Salt from seawater, sand and gravel, bricks, and imported clinker for cement were the only minerals which contributed to the economy. Minerals were not expected to play an important role in the commercial sector of Benin's economy during the next decade. Joint projects included infrastructure development to create a coordinated road and rail system between Niger and Benin that was begun in 1960 as ?Operation Hirondelle." In 1976, an agreement for the construction of a rail link from Niamey, Niger, to Parakou was signed. At Parakou, the rail line would join the existing line to the port at Cotonou. Construction of the rail line was expected to take 6 years, and the cost was estimated at $287 million in 1979. During late 1979, the Federal Republic of Germany granted Benin a loan of $12 million for reconstruction of the port at Porto Novo. Benin and Nigeria were discussing a joint adventure in crude salt exploitation.

Jan 1, 1981

By R. L. Marek

The number of Persons fatally injured in the petroleum industry in California in 1930 was 50, a decrease of 20.6 per cent from 1929, when 63 men accidentally lost their lives. The decrease in the number of fatalities for 1930 has caused the first downward trend in the fatality curve of the California petroleum industry since 1927 and is coincident with a period of little active development in new fields, the shutting in of many wells, and reduced activity in the older fields of the State. That a direct relationship exists between the number of accidental deaths and the rapidity of new field development is particularly emphasized by the fact that in 1929, a year of intensive field development in California, 48 men were killed in the drilling and producing division, whereas in 1930, a year of less development work, only 25 men were killed in this division. The figures for the average number of drilling and producing wells in 1930 decreased appreciably from comparable figures for 1929 and a greater percentage of producing wells were shut-in in 1930 than in 1929.

Jan 1, 1931

By R. L. Marek

The number of persons fatally injured in the petroleum industry in California in 1930 was 50, a decrease of 20.6 per cent from 1929, when 63 men accidentally lost their lives. The decrease in the number of fatalities for 1930 has caused the first downward trend in the fatality curve of the California petroleum industry since 1927 and is coincident with a period of little active development in new fields, the shutting in of many wells, and reduced activity in the older fields of the State. That a direct relationship exists between the number of accidental deaths and the rapidity of new field development is particularly emphasized by the fact that in 1929, a year of intensive field development in California, 48 men were killed in the drilling and producing division, whereas in 1930, a year of less development work, only 25 men were killed in this division. The figures for the average number of drilling and producing wells in 1930 decreased appreciably from, comparable figures for 1929 and a greater percentage of producing wells were shut-in in 1930 than in 1929.

Jan 1, 1931

By Larry A. Haas

The U.S. Bureau of Mines, in cooperation with Cleveland-Cliffs, Inc. (Hibbing, MN), investigated ways of enhancing the quality (compressive strength, after-tumble and reducibility) of domestic acid and fluxed magnetite pellets by modifying the oxygen content during the preheat and induration periods of the firing operation . Oxidation of magnetite was best accomplished when sufficient oxygen and time were available before the peak induration temperature was reached. The rate of magnetite oxidation increased directly with the gas oxygen content during the preheat period at 7000 C and above. With 30 pct ( or more) O2 and a preheat rate of 2000 C/min, most of the magnetite was oxidized during the preheat period. With laboratory tube and mini-pot furnace tests, oxygen enrichment during the preheat period improved the pellet properties more in the simulated grate-kiln tests than in the simulated straight-grate tests. The longer induration period with the grate-kiln test resulted in more sintering of the residual magnetite and its reaction with the silicon compounds. When flux was present in the pellets, calcium silicates and calcium and magnesium ferrites were formed. More calcium ferrite was formed when the magnetite was oxidized early and less iron was present in the fayalitic calcium silicate slag.

Jan 1, 1993

The purpose of Volume II of this study is to provide a general plan for the pilot testing of two materials which could be used to tag explosives for both pre- and postdetonation identification and of tracing techniques which would thereby aid the investigator of an unauthorized bombing or explosion in being able to determine the source and/or user of the explosives. Volume I described the planning factors by which the tagging of explosives could be implemented on a National basis. 1.2 BACKGROUND Tagging explosives at the time of manufacture with a taggant material that could survive detonation, be recovered, and provide an investigative lead has been seriously studied for several years. This concept has gained widespread support among many law enforcement groups because of the scant clues that can presently be found among bombing residue.

Jan 1, 1977