Search Documents

By J. G. Stuart, A. W. Cipkins, R. H. Thompson

Preliminary safe distances for blasting wiring from typical electromagnetic sources are presented. The distances are for underground coal mines and electromagnetic sources in the frequency range below 10 MHz. The distances are based on measurements performed at 3 locations in each of 3 coal mines. The measurement apparatus, measurement procedure, measurement results and the rationale used in the calculation of the safe distances are all described. The safe distances presented are dependent on the measurement results and their interpretation. More measurements are clearly necessary to establish the validity of the suggested distances.

Jan 1, 1985

By J. C. Edwards

The Bureau of Mines developed a mathematical model for analysis of the impact of scrubber bed length, porosity, and gas flow rate on the absorption of C02 in a breathing apparatus. The model accounts for the decrease in available absorbent through chemical conversion. The pre-dicted efflux of C02 from a canister containing LiOR compared favorably with measured values reported elsewhere. It was determined from a com-putational study that the time for breakthrough of C02 at a prescribed level is nearly directly proportional to bed length and inversely pro-portional to gas flow and porosity.

Jan 1, 1987

By John P. Hager

This study investigated the formation of vapor complexes between aluminum chloride and the chlorides of iron, titanium, and silicon. For the A1-Fe-C1 system the proposed gaseous complex species is Al2Fe2C112(g), which is formed according to the reaction 2A1C13(s) + 2FeCl3(s) = Al2Fe2C112(g) The corresponding free energy expression was determined to be ?G° = 38091.49 - 71.45 ? T 400 < T < 600°K The vapor composition above AlC13 melts contaminated with FeC13 was calculated. In the Al-Ti-CI and Al-Si-Cl systems the proposed vapor complex species are Al2Ti2Cl14(g) and Al2Si2Cl14(g) respectively. Free energy expressions were estimated for the formation of the two complex species. Again, the vapor composition above AlCl3 melts contaiminated with TiCl4 or SiCl4 was determined. The results of this study were compared with previous studies on the three systems.

Jan 1, 1980

By D. G. Kesterkel

Low-melting thoriurnrbase binary alloys or metal solutions were prepared by two different techniques involving the electrolysis of ThO2 dissolved in fluoride melts. Experiments were performed at 950° to 1,250° C using electrolytes containing ThF4 and various alkali and alkaline earth fluorides. In the first method, electroreduction of ThO2 and deposition of thorium on a nickel or iron cathode formed a molten alloy that dripped off and collected on the bottom of the cell, or in a tungsten cup. An electrocodeposition technique was used to prepare thorium-base alloys or solutions containing nickel, iron, chromium, or manganese. Electrolytic reduction of the component metal oxides and simultaneous deposition of the two metals on a tungsten cathode yielded a liquid alloy product. Complementary experiments were performed on the fused fluoride electrowinning of dendritic thorium from Th02 at 1,075° to 1,200° C in which thorium crystals were recovered and arc-melted into buttons. Major contaminants were aluminum, carbon, copper, iron, oxygen, and silicon, totaling 0.2 percent.

Jan 1, 1966

By C. M. McKinney

Bureau of Mines routine crude-oil analyses of 42 samples from 37 fields in the major producing areas in Mexico are presented in this report. Table 1 includes information on the source and general characteristics of each sample. Table 2 gives a summary of analytical and computed data. A map (fig. 1) shows approximately where the samples were obtained. ACKNOWLEDGMENTS Grateful acknowledgment is made to Alfonso Barnetche, manager of production, and Ing. Francisco Inguanzo, assistant manager of production, both of Petroleos Mexicanos, who supplied the crude-oil samples and furnished information concerning their sources.

Jan 1, 1960

By Willard L. Hunter

A series of steel heats, one low-alloy and nine carbon, was made by the Bureau of Mines in a 1-ton arc furnace from ferrous scrap from incinerated refuse, steel cans, and detinned steel cans, both alone and blended with heavy-melting scrap. Two additional control heats, one of carbon steel and one of low-alloy steel, were made from electric furnace heavy-melting scrap to pro-vide comparative data. The steel products were cast into two 4-by 4-inch nominal 50-pound ingots; in most heats, an 8-by 8-inch nominal 7S0-pound ingot was also obtained. Tests of these ingots indicated that reinforcing bars of acceptable quality can be made from urban refuse components such as steel cans.

Jan 1, 1976

By Kenneth L. Cashdollar

This report describes three types of optical dust probes that have been designed, built, and tested by the Bureau of Mines. Each of the probes measures dust cloud concentrations by the attentuation of light. The first is a single-path-length probe, the second is a double-path-length probe, and the third is a single-path-length probe that employs jets of air to keep the windows of the light source and detector free from dust coating. The theory of operation and the calibration procedures for each of the probes are described. The results of the Bureaus laboratory, mine, and field tests of the probes are also reported.

Jan 1, 1981

By LeRoy D. Loy

The disposal of excess overburden from surface mining can be accomplished by use of a reclamation technique entitled head-of-hollow or valley fill. This report attempts to assess current valley fill regulations and practices, identifies inherent benefits and deficiencies, and develops concepts to enhance fill technology.

Jan 1, 1978

By O. M. Schaus

The following is a description of the methods employed at the Eureka-Asteroid mine, which is situated on the Gogebic range, at Ramsey, Mich. The mime is operated by the Castile Mining Co. under the direction of Oglebay Norton & Co. This paper has been prepared in accordance with an outline furbished by the United States Bureau of Mines, and in one of a series, on mining methods and costs covering the principal minim operations throughout the United States. ACKNOWLEDGMENTS The author acknowledges the assistance of the mining organization of the Castile Mining Co. in the preparation of this paper.

Jan 1, 1930

By S. M. Shelton, R. B. Fisher, M. M. Fine

"INTRODUCTION The Batesville manganese district lies in the southern part of the Ozark region, mostly in Independence County but partly in Sharp, Izard, and Stone Counties of north central Arkansas.Oxides, carbonates, and silicates of manganese are found in the district. 4/ Carbonate ores have been mined from time to time, but the reserves of potentially commercial ore are chiefly black manganese oxide minerals.The district has produced manganese ore for many years. lip to and including 1933, 160,804 long tons of ferruginous manganese ore (10 to 35 percent manganese) and 140,277 long tons of metallurgical ore (35 percent or more manganese) were shipped;./ most of it was wad orThe term ""wad ore,"" used locally to designate the soft, clayey de¬posits of oxide ore, is a partial misnomer. The ores contain a soft, low-specific-gravity mineral of indefinite composition, which can be designated as wad, but coarse and fine particles of psilomelane and hausmannite, with a smaller proportion of braunite, pyrolusite, and indefinite manganese silicates, are also present. Large and small lumps of high-grade, hard manganese oxide minerals are found, frequently embedded in a soft, black matrix of fine particles of manganese oxides mixed with gangue."

Jul 1, 1942

By George D. Drechsler

The purpose of this review is to provide an analysis of the supply and demand for coal in Europe in 1955-56 and estimates of future growth in European requirements as a medium for appraisal of the effects and benefits to the economy of the United States. This review stems from observations and evaluations made in contacts with Government and industry representatives of the principal countries of Europe and is based on detailed data selected from the established flow of unclassified economic and statistical material originating in overseas areas for use and deposit in the Bureau of Mines, Foreign Solid Fuels Section. This material includes current reports and analyses prepared by the United States Foreign Service, official reports of individual countries, foreign industry and trade publications, and the committees of the several European organizations engaged in continuing review and study of problems relating to fuels and energy. The review is presented in four sections: 1. Discussion of the more important factors relating to the present and future fuels and energy position of Western Europe.

Jan 1, 1957

By R. H. Dickson

This paper, which describes the milling practice of the Verde Central Mines, Inc., is one of a series on milling methods and costs being prepared by the United States Bureau of Mines. GENERAL DESCRIPTION The Verde Central concentrator is located in Walnut Gulch, about 1 mile west of Jerome, Ariz., and on the Jerome-Prescott highway. It is about 1,000 feet distant from the main shaft of the Verde Central mine and treats ore from this mine only. The mill is connected with the main shaft of the mine by a 24-inch gave railway, over which the ore is hauled in 5-cubic yard capacity, rocker, side-dump cars, by a 3-ton Brookville gasoline locomotive.

Jan 1, 1931

By Ernest L. Corp

Seepage forces computed by a finite-element flow program are combined with gravity forces in an elastic-plastic stress-analysis program to determine the stability of mine-waste slopes. Computer output provides a cross-sectional plot of the dam or embankment showing the safety factors for each element. The combined finite-element program called SEEP-SLOPE was used to analyze several trial embankments and the 1972 Buffalo Creek Dam failure Safety factors computed by the finite-element method (FEM) were compared with those computed by Bishop limiting-equilibrium method. For individual slip circles, there was little correlation between the factors of safety computed by the two methods. Both predict failure, but FEM shows a different mode of failure plus development of potential failure zones not indicated by conventional methods. Besides having a better theoretical basis than the Bishop method, FEM requires no assumptions regarding the location or geometry of the failure surface. As a result, the program will show progressive development of a failure zone, and areas can be pinpointed where remedial measures should be taken. In addition, nonhomogeneous cross sections can be analyzed, and zones of potential piping can be defined.

Jan 1, 1975

By H. M. Cooper

Many analysts have had difficulty in obtaining accurate and consistent determinations of the volatile matter in low-temperature coke when the usual standard method for coal was followed. The tendency is toward too-high results, due to mechanical losses which are extremely difficult to avoid or control. With cokes there also may be an error due to excessive oxidation of the fixed carbon. Much of the earlier experimental work on the volatile-matter determination in coal, such as that of Parr, Fieldner and Davis, and others, has been on the effect of time, temperatures, shape and size of crucibles, method of applying heat, and type of furnace, all of which data has evolved the present A.S. T. M. standard method for volatile matter in coal and coke. It is not the purpose of this investigation to deal directly with the above phases of the procedure, but rather to study some of the factors affecting the results in those types of fuel which give erroneous results due to mechanical losses. This mechanical loss is usually designated as "sparking." There are two kinds of sparks or incandescent particles which may appear: particles of soot from partially condensed carbon from the burning gases, and unburned particles of the material itself which escape. The first type does not affect the accuracy of the volatile matter results, and is therefore negligible. The second type, however, causes appreciable loss and results in showing higher volatile percentages than actually exist.

Jan 1, 1932

By S. M. Shelton

The widespread occurrence of domestic manganese deposits and the shortage of ferromanganese-grade ore have been sources of much speculation and investigative effort for many years. The present emergency has intensified the search by the Bureau of Mines for methods of producing ferromanganese-grade concentrates4/ from low-grade ores.

Jan 1, 1941

By S. M. Shelton

[The widespread occurrence of domestic manganese deposits and the shortage of ferromanganese-grade ore have been sources of much speculation and investigative effort for many years. The present emergency has intensified the search by the Bureau of Mines for methods of producing ferromanganese-grade concentrates4/ from low-grade ores.]

Jan 1, 1941

By Richard F. Hewlett

This report describes how a limited number of preliminary exploration drill-hole assays from a mineral deposit can be used to design grid spacing that is both economic and efficient for subsequent evaluation drilling of that deposit. Relationships between desired precision of the estimate of grade of ore and drilling cost are used to determine the economic drill-hole spacing. The statistical concept of precision in estimating grade of ore is used to determine the efficient drill-hole spacing. Assay data from approximately 50 known copper deposits were studied, and the relationships of the statistical parameters of these deposits were computed. Drilling requirements for various precisions of the estimates of grade of ore were computed for some of these known deposits to serve as guides for drilling future copper deposits. The effect of various geologic factors on the trend in grade of ore and, therefore, on the drilling requirements is shown for certain deposits.

Jan 1, 1965

By H. Dolezal

A laboratory study of acid-ferrous sulfate treatment of low-grade manganese ores from the Cuyuna range, Minnesota resulted in 93-percent extraction of manganese as manganese sulfate with consumption of 3.8 pounds of H2S04 per pound of extracted manganese. Two types of ore were treated in consecutive stages. The first are contained carbonate minerals of manganese and iron, both soluble in H2S04 solution. The second ore contained manganese oxide minerals, insoluble in straight acid solution but soluble in the ferrous sulfate solution obtained from treating the first ore. Leaching data were obtained by countercurrent percolation of coarse (minus-1/2-inch) ore particles at room temperature and by agitating minus-65-mesh ore particles in heated solution. Extraction of manganese and acid consumption were the same, but the percolation leach required 6 days compared with 1 hour for hot agitation. Variations in the size of ore particles treated, leaching time, acid concentration, solution temperatures, and method of applying ferrous sulfate solution to the oxide ore were studied. The effects of several reagents for removing iron from solution and improving filtration were also studied.

Jan 1, 1959

By F. S. LOTT, I. S. CULVER

The number of petroleum refineries in the United States decreased during 1948 from 390 to 375, continuing the trend to fewer units of larger individual capacity that has persisted since the peak in number of plants was recorded on January 1 , 1936. Large - scale construction of new processing facilities continued through 1948 with a resultant gain in daily crude-oil throughput capacity of installed equipment from 6,034,252 barrels on January 1 , 1948 to 6,438,995 barrels on January 1 , 1949. The capacity of the average refinery to process crude oil therefore increased during 1948 from 15,472 barrels daily to 17,171 . The principal areas of expansion of facilities were the strategic seaboard districts of the Texas and Louisiana Gulf Coast and the East Coast , and the important Indiana , Illinois , Kentucky, etc. , district that supplies markets in the upper Middle West region . These four districts accounted for 79 percent of the total new capacity added in the United States in 1948. The relatively small petroleum- refining industry of the Other Rocky Mountain district experienced a vigorous expansion in 1948 that will continue during 1949 . Capacity building on January 1, 1949 , amounting to 341,500 barrels daily, was 25,750 barrels lower than the comparable total on January 1 , 1948, but was the second highest on record . New construction was heavily concentrated in the Texas Gulf, East Coast , and Indiana -Illinois

Sep 1, 1949

By H. C. Fuller, E. L. Anderson, F. S. Wartman, M. A. Cook

"This paper gives an account of the production of ductile-grade titanium powder in 100-pound batches by reduction of purified titanic chloride with magnesium, followed by grinding, leaching, and magnetic separation of the reaction product. Apparatus, technique, and methods of controlling product quality are described, and some data on operating costs are given.Although man has been aware of the existence of the element titanium for over 150 years, only recently has the metal itself been available in a form pure enough, particularly with reference to absorbed gases, to allow an estimate of its physical properties. In comparison with mild steel, the tensile strength of titanium is about the same, the resistance to atmospheric corrosion greater, and the specific gravity much less.These properties suggest the usefulness of titanium as a structural material for applications requiring resistance to atmospheric attack and a good strength-weight ratio. Although known reserves of titanium, high-grade enough to be useful at present are not sufficiently extensive to predicate that titanium might supplant iron, aluminum, and magnesium for structural purposes, the reserves are large enough to make its use as a structural material quite feasible in certain fields in which its unique properties are required.As a result of these considerations, the Bureau of Mines station at Tucson initiated an, investigation into the technology of titanium in 1938. First, a critical survey and small-scale trial of virtually all suggested methods7/ for producing the metal was made. The method devised by Kroll8/ seemed best adapted as a source of metallic titanium for, although the purity of the product was not as high as that of products from some other processes, it seemed that modifications in technique necessary for larger-scale production could be made more easily.Essentially, in applying the Kroll process, titanium tetrachloride was reduced to metallic titanium by adding the chloride slowly to molten magnesium contained in a molybdenum-lined iron reaction chamber filled with a protective atmosphere of argon. After reduction to the state of completion desired, the reduction mass and chamber were allowed to cool. Then the chamber was opened, and the reaction mass, consisting of titanium, magnesium chloride, and some unused magnesium, was removed by suitable means. Most of the magnesium chloride and metallic magnesium were removed by leaching in dilute hydrochloric acid. The leached sponge was then ground wet in a ball mill, releached in strong acid, and dried Removal of free iron by magnetic separation completed the production process.Development of the Kroll process by the Bureau was undertaken first at the station at Salt Lake City, in 1942 and the amount formed per run was increased in several steps from a few grams to pounds.9/ In addition to increasing the size of batch over that used by Kroll, the technique was simplified somewhat by the use of unlined reaction vessels."

Aug 1, 1949