Search Documents

By H. V. Makar

The Bureau of Mines successfully demonstrated, on a pilot plant scale, a sodium sulfate (Na2S04) refining process for removal of copper from molten ferrous scrap. Previous tests established technical feasibility on a bench scale for achieving low copper concentrations and determining the principal factors controlling process efficiency. The pilot plant study involved a 1-ton arc furnace for melting ferrous scrap and a 1-1/2-ton treatment ladle. Results of these tests showed that copper removals obtained in laboratory tests (approximately 40 relative percent copper removal with 10 weight-percent surface addition of sodium sulfate) could be achieved on the pilot plant scale when excess carbon was added with the sodium sulfate compacts. Data were obtained on temperature losses and carbon consumption related to Na2SO4 treatment.

Jan 1, 1974

By M. M. Fine

Small-scale laboratory mineral-dressing studies were made on a total of nine individual or composite samples of manganese-bearing material from the west-central Arkansas, or Mena, district. Of these, only three yielded concentrates that would probably be acceptable for purchases by the Federal Government fur the National Stockpile. Concentrates from some of the other properties, however, contained more than 40 percent Mn and might be merchantable to other purchasers of manganese ore. In most instances, a too-intimate association of manganese oxides and gangue is conducive to low grade, low recovery, or both, so that mechanical concentration processes do not promise much for this district.

Jan 1, 1956

By M. R. Geer

American and European practices in cleaning fine coal are strikingly different. The tables, launders, classifiers, and pneumatic devices used in America are seldom employed in Continental Europe, where much of the fine coal is cleaned in feldspar jigs, often supplemented by froth flotation of the extreme fines. This difference in choice of cleaning equipment may be fortuitous, but in large measure can be attributed to a difference in economic factors. Coal being more costly in Europe, there is greater emphasis on efficient cleaning of all sizes, including the extreme fines, and it is common to produce a high-ash middling for "on-site" consumption to avoid any waste of fuel value. The feldspar jig has been found advantageous under these conditions. In the United States fuel coal must be prepared as cheaply as possible, and metallurgical coal must be prepared as efficiently as possible; thus in both branches of preparation practice, any cleaning device that promises greater economy or higher efficiency warrants consideration. The feldspar jig, as employed in Europe, has a much higher unit capacity than the wet table used so extensively here and therefore offers economy in the capital costs of a washery through saving in space. As pointed out by Vissac,4/ the jig operates under automatic control, and therefore can cope with fluctuations in quality of feed. Maintenance costs for a single, large-capacity unit, such as the feldspar jig, would be expected to be lower than those for a battery of low-capacity cleaners. These considerations led the Bureau of Mines to undertake an investigation of the feldspar jig to determine its possible usefulness in this country.

Jan 1, 1958

By Bertrand L. Johnson

As potash is more necessary to the agricultural economy of the United States now than ever before it is gratifying to find that the virtual stoppage of imports from Germany in late 1939 caused none of the anxious foreboding that gripped American farmers in 1914. For long decades this country, in common with tie rest of the world, depended upon German potash, but today our expanded needs can be mot from domestic sources. The present armed conflict in Europe, like that of 1914, disrupted a world monopoly, but the cartel that in recent years controlled 90 percent of the world output (see fig, 1) was an international syndicate comprising French, Polish, and Spanish as well as German producers and having reported sales agreements covering production in the U. S. S. R. and Palestine. The break-up of these commercial agreements has necessitated readjustments but generates no such alarm as the closing of a single source of supply. In striking contrast to the critical shortage that developed a quarter century ago, no increase in prices has occurred or is anticipated in the domestic market.

Jan 1, 1940

By Richard L. Unger

The U.S. Bureau of Mines has designed, fabricated, and tested a prototype track maintenance vehicle for underground coal mines. The vehicle uses a stiff rotating brush to clean the track so that a visual inspection is possible. It is also equipped to measure track gauge and cross-level. The objective of this report was to describe the track maintenance vehicle and detail the results of investigations into present underground track inspection procedures and cleaning technologies, which led to the development of the prototype. Recommendations are made concerning the integration of components of this prototype vehicle into current track cleaning and inspection systems used in underground mines.

Jan 1, 1984

By K. J. Miller

Electrophoretic mobility measurements of coal and pyrite particles in distilled water revealed a difference between the migration speeds of the two materials toward the anode in a dc electric field. This information led to the development of a laboratory electrophoresis column for separating fine pyrite from coal by utilizing the electrokinetic and the specific gravity differences between coal and pyrite. The study demonstrated on a laboratory scale that pyrite and other impurities can be separated from fine coal by electrophoresis using a stage separation technique. In a cost analysis, electrical power for electrophoresis was extrapolated to about $1 per ton of clean coal product. But, since the only successful tests ever made were in the laboratory with prewashed samples of minus 100-plus 325-mesh coal in distilled water, the cost figure derived is not representative of conditions prevalent in commercial coal cleaning operations. True conditions would reflect costs many times as great. In the course of the work, several scale-up techniques were considered but their feasibility became academic in view of the physical and economic problems associated with electrophoretic separation of pyrite from coal. Although the process and apparatus were finally deemed impractical for commercial coal preparation, the electrophoresis column may have some application as a laboratory device.

Jan 1, 1974

By Richard N. Appling

This compilation presents information obtained through investigation of manganese deposits and a reconnaissance of potential manganese-bearing areas of southwestern Oregon and Del Norte County, Calif., from October 1952 to September 1955. The report includes maps, assays, and preliminary examination data on 39 manganese deposits distributed throughout Curry, Coos, Douglas, Josephine, and Jackson Counties, Oreg., and 1 deposit in Del Norte County, Calif. On the basis of mineral content the deposits can be divided into three groups: 1 Manganese silicate deposits, manganese oxide deposits, and manganiferous iron de-posits. Generally the oxides occur along the coast in the Curry-Coos County area, the manganiferous iron deposits are in the Josephine-Douglas area, and the manganese silicates are found in both the Josephine-Douglas and Jackson County areas. The deposits are characteristically irregular in form and usually small. Most silicate and manganiferous iron deposits are in metasediments of Triassic (?) age; oxide deposits are in sediments varying in age from Jurassic to Eocene.

Jan 1, 1957

By Laxman S. Sundae

The Bureau of Mines designed, fabricated, and is using an in-seam tester (1ST) for in situ determination of coal cutting forces. This re-port describes the results of field tests conducted in the Pocahontas No. 3 and Upper Freeport seams to obtain peak and mean cutting forces during coal cutting with several bit geometries, including radial and point attack bits currently used on drum-type machines. Comparisons were also made between new and worn bits, and using data obtained from a Bureau-modified chisel bit. The test results show that longwall plough cutting (horizontal cuts) in bony coal bands (shale) requires >3 times the cutting force for the same cuts in a vertical direction. When no bony coal is present, the cutting forces required to make horizontal and vertical cuts are equal. Worn bits require 4 to 5 times more cutting and normal force than new or undamaged bits. Normal force increased drastically for the worn chisel bit. Peak force encountered in making independent cuts was found to be ~3 times higher than that required to make interactive cuts using a spacing-to-depth-of-cut ratio of 2. Both rake and clearance angles were found to have a significant effect on normal and cutting force.

Jan 1, 1986

By D. Harrington

Approximately 6,000 coal mines are operated in the United States. All of them have in some degree the elements that are likely to contribute to an explosion, hence it is surprising that explosion disasters are not more frequent and that many mines have been operated for years and finally worked out and abandoned without experiencing an explosion. The absence of coal-mine explosions does not always indicate that effective efforts have been made to prevent them but rather that the nine has been fortunate in that the combination of circumstances necessary to cause an explosion has not existed. In view of present knowledge of the methods of preventing explosions, disasters are inexcusable and discredit the mining industry. The methods of preventing mine explosions are known to experienced, well-informed persons engaged in coal mining, yet despite this knowledge far to many coal-mine operators continue to use practices and methods that they should know have resulted in numerous explosions. Moreover, many mine workers persist in following past procedure irrespective of consequences and in breaking safety rules or indulging in practices almost certain eventually to result in disaster. Continued failure to apply known common-sense methods of accident and explosion prevention unquestionably will cell for ultimate enforcement of law.

Jan 1, 1940

By R. Hogg, T. F. Dumm

"Abstract - With increasing interest in the physical cleaning of fine coal, there is a need for extension of the sink float analysis procedure to finer sizes. Problems arise, however, in ensuring complete dispersion of the particles in the heavy liquids. A procedure has been developed in which surfactants are used as dispersing agents, and solids concentration is minimized (using a simple formula to estimate the minimum weight needed for statistical reliability). Using centrifuges to increase separation rates and subsieve particle size analysis of the specific gravity fractions, a complete size specific gravity distribution can be obtained. Analyses have been performed on coal samples as fine as -10 µm.IntroductionTraditional gravity separation techniques such as jigging, heavy media and water-only cyclones, shaking tables, etc., have been used to remove impurities from coal ranging in size from about 15.cm (6 ln.) to about 150 µm (100 mesh). The coal washabilty or float-and sink technique ls a well-established procedure for determining the optimum extent to which a coal can be cleaned by such physical separation methods. Because of the desire to recover even finer coal fractions by gravity separation techniques, there is a need to extend the coal washabillty analysis into the ultrafine range. The purpose of this paper ls to describe some of the significant factors that influence fine particle specific gravity separation. Washability analyses have been performed on three ultrafine ( <10 µm) coal samples representing three general mining districts in Pennsylvania. Results of these analyses indicate that the washabillty technique can be successfully applied to ultrafine particles when proper care ls taken."

Jan 1, 1988

By D. R. Flinn

The Bureau of Mines has studied the electrochemical parameters important to the preparation of coatings of the platinum-group metals. Using molten mixtures of sodium and potassium cyanides in an inert atmosphere, techniques have been developed that permit the preparation of baths for platinum, rhodium, and iridium electrodeposition. Cyclic voltammetric and slow sweep rate linear polarization techniques have been utilized to determine optimum potential and current values for preparation of plating baths and for the electrodeposition of coatings. Techniques are described for the deposition of platinum and rhodium coatings at near 100 percent anode and cathode current efficiencies, and for iridium at approximately 80-percent efficiency. Palladium deposition from these molten cyanide baths remains un-satisfactory. The chemistry of the palladium-containing cyanide bath is discussed. Examples of scanning electron microscope photomicrographs of typical platinum coatings are presented. Techniques are described for the preparation of platinum coatings on large objects.

Jan 1, 1982

By T. E. Green, E. F. Spano, W. J. Campbell

A combined ion - exchange X- ray spectrographic method was developed and evaluated for determining trace amounts of cobalt and nickel in high - purity tungsten and tungsten trioxide . The sensitivity for both cobalt and nickel is in the range from 0.2 to 0.5 μg ( 0.04 to 0.1 ppm , based on 5 gram samples ) . Accuracy at the 5 to 20 μg level is ±10 percent of the amount present . Approximately 16 hours elapsed time is required for analysis

Jan 1, 1963

By E. G. King

This publication presents original thermal data for a typical variety of perlite and supplies basic information for use in computing energy requirements in processes for expanding perlite. Perlite has been defined by Raiston 4/ as any silicious lava containing dissolved water in sufficient amount to errand into bubbles when the material is quickly heated to a suitable point in the softening range." The uses of expanded perlite in) the construction and ceramic industries have been discussed by Ralston 4/ and King. 5/ The work described here had a dual purpose: (1) It was desired to ascertain quantitatively, using a typical variety of perlite, just how firmly the contained water is held, and (2) it was desired to obtain basic thermal data sufficient for energy-requirement calculations in processes for expanding perlite.

Jan 1, 1948

By Donald O. Capstick

[ ]

Jan 1, 1983

By William C. Cooley

This volume contains copies of the 5 x 8 in. accession card file for all items collected which were judged to be relevant to underground hydraulic coal mining. In many cases, abstracts are included. Abstracts were taken from the source, from other reviews, or from the preliminary screening of Russian documents performed by Dr. A. L. Brichant. No attempt was made to write abstracts for every accession item.

Jan 1, 1975

By J. K. Whyatt

Researchers at the U.S. Bureau of Mines have been exploring recent advances in the use of strain-softening constitutive laws that approximate shear fracturing. The purpose of these tests is to investigate shear-fracture-related rock bursts in hard-rock mines. The capabilities and remaining problems in the use of strain-softening laws in finite-element, distinct-element, and finite-difference methods are reviewed. Performance of the finite-difference implementation of strain softening is compared to classic experimental results and observations of rock mass behavior in the Coeur d&apos;Alene Mining District of northern Idaho. The results show promise for developing methods to identify the general location and orientation of shear fractures and their sequence of occurrence, but such methods cannot be relied upon to quantify post-fracture loads or displacements accurately. Uncertainty over the amount of energy consumed by failing rock and the dependency of energy consumption on model mesh definition prevent direct application of the results to analyses of rock bursts.

Jan 1, 2010

By P. L. Sibrell

The U.S. Bureau of Mines has tested cyanide leaching for recovery of palladium (Pd) from spent petroleum processing catalysts. Three different catalyst samples were supplied by a spent-catalyst processor. These catalysts consisted of a zeolite base and contained 0.4 to 0.7 pct Pd. During alkaline cyanide leaching, the catalysts exhibited ion-exchange properties due to their zeolite matrices. Hydrogen ions were released from the zeolite in exchange for sodium ions in solution, resulting in a significant decrease in solution pH. This could present a safety hazard because of the potential for release of toxic hydrogen cyanide gas. A pretreatment step where the catalysts were contacted with a 1.0M sodium hydroxide solution was found to prevent the pH shift from occurring. Following the sodium hydroxide pretreatment, two stages of leaching at 160 °C with solution containing 1 pct sodium cyanide and 0.1[M] sodium hydroxide gave at least 75 and up to 95 pct Pd recovery. The Pd was quantitatively recovered from the leach solution by thermal decomposition in an autoclave at 250°C for 1 h. The Pd content of the precipitate was over 50 pct. Thermal decomposition also decreased the total cyanide content of the barren solution to less than 0.2 mg/L. The catalyst leach residues passed the Federal Toxicity Characteristic Leaching Procedure and the California Waste Extraction Test, indicating that landfill disposal of the leach residues would be acceptable.

Jan 1, 2010

By Warren D. Longwill

The Bureau of Mines inventoried Federal lands in the State of Oregon and classified them in detail, section by section, according to their availability for mineral exploration and development as affected by legal status and agency management practices. The Bureau determined areas of the State having past mineral production and/or known metallic mineral resources and areas favorable for coal, oil, gas, and geothermal resources, and prepared maps that spatially compare the availability of Federal mineral land with these mineral areas to demonstrate the extent of restrictions to mineral entry. Oregon contains 62.1 million acres, of which 33.9 million acres or 55% is Federal mineral land. About 2.3 million acres of Federal land is favorable for selected metallic mineral deposits, of which 64% is available, 13% is restricted, and 23% is unavailable. Of the 21.1 million acres of Federal leasable land favorable for oil and gas, 68% is available, 11 % is restricted, and 21 % is unavailable. Of the 146,720 acres favorable for coal, approximately 71% is available, 13% is restricted, and 16% is unavailable. Federal leasable land favorable for geothermal resources amounts to 458,968 acres, of which 42% is available, 34% is restricted, and 24% is unavailable.

Jan 1, 1988

This report describes the results of a program to design, procure, install, and evaluate a multi-channel underground telephone system of modern design in the Sunshine Silver Mine near Wallace, Idaho. Although the evaluation portion of the program was deleted, this report contains a cost benefit analysis for such a system using estimates of operational data for the Sunshine Mine. The results show a centrally switched telephone system of conventional design with ruggedized phone enclosures and special environmentally sealed dial pads to be the most economical.

Jan 1, 1982

By B. W. Gandrud, G. D. Coe

"INTRODUCTION The Bureau of Mines, United States Department of the Interior, with the cooperation of the University of Alabama and coal producers of Alabama, is making a series of washability studies to obtain technically and commercially important data from the productive coal beds of the State. Based on the system followed in these studies, this report consists of screen-sizing and sink-and-float data on the America and Pratt beds at Gorgas, Ala.SAMPLING AT THE MINESAlthough operations were discontinued in 1929, the accessible openings of the old Gorgas mines of the Southeastern Fuel Co. made possible the taking of samples from the America bed at three openings and from the Pratt bed at two openings. A sample was taken from the America bed at the Klondyke opening; a second was taken about 1 rile south of the Klondyke at the Musgrove America opening, and a third sample was taken about 1-1/2 miles south of the Musgrove-America at the Cricket Lodge opening. A sample was taken from the Pratt bed at Musgrove-Pratt No. 1, which is about 3/4 mile east of Musgrove-America, and a second sample was taken at Musgrove-Pratt No. 2, which is about 3/4 mile west of Musgrove-America. The samples ranged in weight from 1/2 ton to 1 ton and were equivalent to approximately a 2-ton sample from each bed. Figure 1 shows sections of the beds at the places sampled.In addition to the samples for washability study, a seam sample for analysis was taken at each of the places sampled. So as to give a representative seam sample for each of the two beds, these samples were combined in the laboratory in proportion to the thickness of the bed at the places sampled."

Jul 1, 1939