Search Documents

By L. F. Christianson

The presence of salt in crude petroleum has been known for many years, but recently the percentage of chloride salts of calcium, magnesium, and sodium produced with some crude oils has increased to such an extent that the removal of the salty compounds is imperative for some refiners and their presence causes considerable apprehension for others. The exact reason for this increase of salts is not known definitely, but in all probability a combination of factors contributes to the condition. The most important are acidizing of wells, development of new fields producing crude oils of greater salt content, and the depletion of old fields with an attending increase in the production of emulsified brine. Due to handling

Jan 1, 1938

By R. R. Lowery

The Bureau of Mines developed hypereutectic aluminum-silicon alloys which 11.7.d better mechanical properties than the unmodified hypereutectic alloy. A commercial aluminum-20 weight-percent silicon LIr alloy was selected as a ary base for improvement. The primary silicon. grains were reduced from ASTM 4-5 to ASTM 8.5 by the use of phosphorus and phosphorus compounds. The remaining eutectic matrix was refined by sodium metal additions of 0.2 weight-percent. Solid solution strengthening of the alpha aluminum was obtained by adding 2 percent copper and 0.5 percent magnesium. Also, 1 percent nickel was added to harden the alloy. Optimum thermal treatment consisted of a solution treatment for 10 hour:, at 480° C with hot water quench, followed by aging for 6 hours at 175° C. The final alloy exhibited a Rockwell B hardness of 75 ±2 in the heat-treated condition. The ultimate tensile strength was 39,5O0 psi with no recordable elongation. The coefficient of linear thermal expansion was 20.4 x 10-6 per °C in the temperature range 20° to 300° C. No wear resistance data were collected.

Jan 1, 1966

By B. D. Nash

The object of this research was to investigate the technical feasibility of preparing chromium metal by the thermal decomposition of bisbenzene chromium. Bisbenzene chromium, a pi-bonded sandwich type organometallic compound, was thermally decomposed under reduced pressure to form a metal plate on a heated substrate. Metal recovery was close to 100 percent of theoretical, with deposition rates up to 20.8 mg/hr/cm2. Metal purity was dependent not only upon the purity of the starting material, but also upon the sublimation rate of bisbenzene chromium. Total detectable metallic impurities ranged from a low of 18 ppm to several hundred ppm. In general, metallic impurities were less than 100 ppm. Carbon, the major nonmetallic impurity, ranged from less than 0.3 percent to more than 10 percent. The carbon contamination is most likely a result of the decomposition of the organic portion of bisbenzene chromium. An unusual property of some of the deposits was their outstanding corrosion resistance. Unlike pure electrolytic chromium, which dissolves readily, these deposits were insoluble in hot mineral acids.

Jan 1, 1968

By Alfred L. Ransome

The consumption of slab zinc in the United States increased sevenfold in less than a half century since 1900. Therein is reflected the innate characteristics of this versatile and nearly indispensable nonferrous metal whose use has grown at more than twice the rate of industrial production. The total metal consumption was substantially stimulated during the two World War periods, which were likewise marked by notable changes in use pattern accompanied by shifts in geographic distribution. This information circular summarizes basic data collected for many years by the Bureau of Mines, but in particular presents for the 1940-45 period details derived from the comprehensive slab zinc consumption survey inaugurated in 1940. The total consumption of slab zinc has been broken down into four major categories galvanizing, brass products, rolled zinc, and zinc-base alloys -- with minor applications grouped under a fifth heading, other uses. Ex- cept for the inclusion of zinc-base alloys with other uses before 1926, the above-named segregation has been shown for the entire period 1900-45. 11- though a substantial tonnage was taken by all groups in all years, there were large shifts in the use pattern in both World War periods. In both, the Allied Powers depended heavily on the United States for zinc-bearing products, especially those required by war industrius. The departures from usual uses were, however, much more marked during the second than in the first period, mainly because the United States could not have met the tro- mendously expanded war-materiel demands had the greater slab zinc needs of a period of high industrial activity been supplied. The geography of consumption is known in detail only for 1940-45. Even in that short period, substantial shifts are observable, largely the reaction from conversion to war production in 1940-41 and reconversion to peacetime consumption in 1945. However, there is so evidence of other shifts in consumption centers that appear to reflect longer-term develop- ments.

Feb 1, 1948

By John C. Feeley

The methods used and the funds available for the development and oper- ation of shall mines and the reopening of small abandoned mines frequently present problems that tax the ingenuity and resourcefulness of the mining engineer far beyond that required in the mass production from large deposits. The objective of this paper is to describe in considerable detail the means whereby engineers have solved local problems in reopening an abandoned mine at which equipment, facilities, and funds were limited... The Etowah Coal & Iron Co. Gadsden red-iron-ore mine at Gadsden, Ala., 18 of interest in this category since it is the only independent red-ore mine under active development in the State. All other red-ore mines in Alabama are owned or controlled by the large iron or steel companies. The The mine, located on the southwest end of Shinbone Ridge in the outskirts of Gadsden lies in an ares once productive. but now idle, for many years. ore is relatively highgrade compared with that in the Birmingham area, but the bed is thin and somewhat lenticular. The presence of a large blast furnace at Alabama City, 3 miles from Gadsden, and the growing scarcity of red-iron ore supplies for it offered inducements for reopening the mine in 1946. Up to the time this circular was prepared (1947) only a small quantity of ore (about 1,500 tons) has been produced and shipped to the furnace. A force of 14 men was employed in sinking the main slope and developing a third "lift" (a local term for level) 100 feet below the old mine workings.

May 1, 1949

By B. W. Madsen

Research by the Bureau of Mines has shown that treatment of open pit waste by crushing and sizing followed by flotation of the fines and leaching the coarse fraction results in greater metal recoveries than obtained by leaching only. Tests with a chalcocite-bearing quartz monzonite mine waste sample that had been crushed to minus 6 inches and screened on 1/2 inch yielded copper and silver recoveries of 71 and 22 percent, respectively, by the combined flotation-leaching process, compared with 48 percent of the copper and no silver recovered leaching the run-of-mine material. Copper was more readily leached from the coarse material with the minus 1/2-inch fines removed than from material with the fines included. The improved leaching was attributed to improved permeability and the associated improved circulation of air to the interior of the ore column. Cost estimates showed that the proposed intensive treatment of mine waste will require a greater capital investment and higher annual operating costs than conventional milling and dump leaching process. However, the income from the additional metal production offsets the increase in capital investment and operating costs, resulting in additional profit.

Jan 1, 1975

By H. A. Doerner

"During the year which has passed since the last progress report on reduction of zinc by natural gas,3 the laboratory experiments on this investigation have been completed. In this concluding report, the whole subject will be reviewed and additional data presented.Chemical ReactionsIn a thermodynamic study of zinc smelting, Maier 4 discussed the use of methane for reducing zinc oxide, and predicted equilibria at various temperatures for the sore important reactions. The study has been extended to include the following list.Maier predicted that 870°C. would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1) at equilibria would be substantially complete at or above 927°C. A subsequent papers described experimental verification of these predictions and gave data on reaction rates under various conditions.It methane is passed through a heated bed of zinc oxide at a low enough rate reactions (1), (3), and (4) reach an equilibrium which can be expressed by reaction (10). The equilibrium concentrations for the products of this reaction in the temperature range 900° to 1100°C. were calculated by applying the thermodynamic constants to the stoichiometric relations. 6 The results of these calculations are listed in table 1 and shown graphically in figures 1, A and B. These data have major importance, and experimental work has shown that they are subtantially correct."

Dec 1, 1934

By A. M. Evans, J. H. Soulé

"INTRODUCTION Deposits of iron ore in Cherokee County, Tex., have been worked at various times in the pact, and the ore has been smelted in small local blast furnaces.Recently it was proposed to establish a charcoal blast furnace with a wood distillation plant to produce charcoal for fuel and byproducts. Financial assistance from the Reconstruction Finance Corporation was sought by George Easley and associates to enable them to purchase, move, and erect the furnace and build the required accessory plants. The furnace was to be moved from Pembroke, Fla.In August 1941, the Bureau of Mines was asked by the Office of Production Management to check the development work of Easley and associates and to ascertain (1) the iron-ore reserves, (2) the cost of mining ore and delivering it to the blast furnace, and (3) the grade and character of the ore. The Bureau of Mines was advised, while the investigation was in progress, that approximately 1,000,000 long tons of measured reserves would be sufficient to demonstrate the feasibility of operating the properties.Although deposits of iron ore are widely distributed in Cherokee County, only the Pryor Mountain, Banks and Cherokee, J. P. Acker, and Citizens State Bank tracts were sampled thoroughly by the Bureau of Mines. The iron-ore rights on these are owned by the New Birmingham Development Co., the Cherokee Development Co., or by individuals. Options to lease the ore rights were obtained by Easley, who obtained options on the Hawes Peach Orchard and Bradford tracts, also, which were examined only cursorily by the Bureau."

Aug 1, 1947

By J. D. Davis

THE CARBONIZING properties of Chilton-bed coal from Lorado No. 5 mine, HE Logan County, W. Va., were determined by Bureau of Mines-American Gas Association tests at 600°, 700°, 800°, 900°, and 1,000° C. and by expansion tests. Chemical analyses, agglutinating and plasticity tests, and low- and high-temperature assays also were included in the investigation. Blends with low-volatile Pocahontas No. 3 coal were carbonized at. 900° C. The Chilton coal bed lies in the Kanawha, or Upper Pottsville formation of the Pennsylvanian system; the estimated original reserves are nearly 3.2 billion tons. The bed was 39/1 to 57 inches thick in the Lorado No. 5 mine, and the coal was 38 to 57 inches thick. The carbonization sample contained 62.6 percent fixed carbon on the dry, mineral-matter-free, basis, and the heating value on the moist, mineral-matter-free basis was 15,190 B. t. u. per pound; it therefore ranks as high-volatile A bituminous. It contained 1.8 percent moisture, 35.2 percent volatile matter, 57.9 percent fixed carbon, 5.1 percent ash, and 0.7 percent sulfur, as carbonized. The sulfur was largely organic, and the ash softened at 2,630° F. The agglutinating value determined on a silicon carbide-coal mixture of 15:1 was 6.8. In the Gieseler test the coal softened at 327° C., fused at 407° C., attained a maximum fluidity of 5,730 dial divisions per minute at 435° C., and solidified at 487° C. Maximum resistance in the Davis plastometer was 45.5 pound-inches.

Jan 1, 1951

By N. E. Hanna

As part of a program for improving, the safety of permissible explosives, the Federal Bureau of Mines has undertaken an investigation to establish the ability of sodium chloride to reduce the incendivity of permissible explosives to firedamp atmospheres. A motivating influence for this investigation has been the comparatively extensive experience of British and other European investigators, who used sodium chloride as a component of their permitted explosives (1, 5, 6 7).5/ In the United States research and development work of this type has been less extensive, although sodium chloride has been added to permissible explosives as a cooling agent (9) for many years. The results of the first phase of this investigation were presented in a previous paper (8), which established that adding up to 10 percent sodium chloride to permissible explosives reduces the likelihood of ignition of firedamp in the gallery test; however, the results were somewhat inconsistent, and the conclusions were qualified. Accordingly, the investigation was continued with a study of the effect of added sodium chloride as a function of the quantity added and of the particle size of the salt.

Jan 1, 1960

By G. R. Smith

This report describes research carried out by the Bureau of Mines to develop new technology for electrorefining metals at much higher current densities than those normally used in commercial practice, preliminary studies using rotating-ring and cylinder electrodes to increase the mass transport of copper are discussed. Following this work, single- and multichannel cells were developed that utilized a high electrolyte flow in the channels formed by the anode-cathode pairs. Using these cells, copper was successfully refined at current densities in the range of 70 to 300 amp/ft2. The effects of flow rate, electrolyte composition, and grain-refining and leveling agents on the morphology and purity of electrodeposited copper were determined.

Jan 1, 1979

By J. Robert Wells

The Bureau of Mines has developed a spectrochemical procedure for determining 19 impurity elements in high-purity titanium metal, titanium oxides, and titanium halides in which all samples are converted to titanium dioxide. Determination of these impurities was studied in the general concentration range of 0 to 1,000 p.p.m., but different determination limits were found for the various elements. The procedure is quantitative for 18 elements but semi-quantitative3 for beryllium and has an overall relative standard deviation of 15.8 percent. Two mixtures were used, one composed of graphite and lithium carbonate plus gallium oxide and the other of graphite and lithium carbonate plus germanium dioxide. Each mixture was blended mechanically with an equal weight of titanium dioxide. Lithium carbonate served as buffer-diluent. Gallium was the internal standard for 1 impurity element, germanium for 7, and titanium for the remaining 11.

Jan 1, 1962

By Donald P. Schlick

This Information Circular presents a brief historical digest of the early attempts of the Bureau of Nines and the U.S. Public Health Service to establish coal mine dust exposure standards. It reviews current, accepted standards of the United States as well as available standards of other countries.

Jan 1, 1971

The panic bars (and associated linkages and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on self-propelled, electric and diesel face equipment: including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that arc recommended in this document, but all of the panic bars are characteristically of the "fire door" type that is frequently encountered on outside exit doors of many public and some commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes are added to the face equipment machinery for which they arc required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in "Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel al the various machine manufacturers and underground coal mines that we surveyed, discussions with G. L. Judy (our consultant), etc:

Jan 1, 1974

By Bernard Porter

The densities of LiF, NaF, and KF, of binary mixtures of these alkali fluorides, and of binary mixtures of UF4, ThF4, YF3, LaF3, and CeF with each of tie alkali fluorides were measured as functions of the melt composition and temperature. Molar volumes at 1,000° C were calculated for all the mixtures. Binary systems containing LiF exhibited molar volume ideality. Binary fluoride systems containing either NaF or KF as the alkali fluoride exhibit positive deviations from molar volume additivity. However, molar volumes in the NaF-KF system are ideal.

Jan 1, 1966

By Sam Friedman

The Bureau of Mines conducted experiments using bench-scale apparatus to explore the effect of large changes in process variables on the yield and composition of the gases produced by passing 800° C steam through a fixed bed of Pittsburgh seam (hvab) coal. The total yield of combustible gases increased throughout the given range for the following variables: Superficial steam velocity increasing from 0.02 to 0.12 fps, pressure increasing from 1,000 to 6,000 psig, residence time increasing from 0 to 60 minutes, and temperature increasing from 800° to 900° C; however, a greater increase in the yield of hydrogen in comparison with the increase in yield of methane reduced the gross heating value of the gas to around 470 Btu per scf at conditions giving the maximum yield. Pressures of 1,000, 3,000, and 6,000 psig at 0.09 fps steam velocity, 800° C, and 60 minutes residence time, respectively, produced methane yields of 20, 24, and 22 percent, based on maf coal, with the gross heating value of the CO2-free gas decreasing from 552 to 520 and to 470 Btu per scf. Methane concentrations in the CO2-free gas were 26, 22, and 14 percent, respectively. Based on the gross heating value of the coal, the percentage of the heating value recovered in the gas was 60, 71, and 87 percent, respectively. The use of tungsten sulfide as a catalyst for converting carbon oxides and hydrogen into methane was explored briefly using both a sulfur-free gas rich in methane and a sulfur-bearing synthesis gas (3H2:1CO).

Jan 1, 1968

By Jr. Hazen

Relationships that may exist between assays and sample interval lengths when using unequal sample intervals in mine sampling have been investigated as part of the larger research problem of adapting statistical methods to the analysis of weighted average grades. The theoretical relationship between the amount of difference in the weighted and unweighted average grade of ore and the size of the correlation coefficient between assay value and sample interval length was found to be linear. Numerous examples of actual field sample and assay data, which have been obtained by using unequal sample intervals, are documented, and the differences between weighted and unweighted average grades of ore and the correlation coefficients between assays and sample interval lengths have been computed and plotted on graphs. Differences between these actual field data and the expected theoretical linear relationship are examined. It is hypothesized that the use of unequal sample intervals in mine sampling is, in fact, stratified sampling in a statistical context. The sampler establishes stratification by selecting unequal sample intervals on the basis of differences in lithology, changes in rock type, characteristics of mineralization, or differences in metal content. Statistically} methods currently used in mine sampling, involving unequal sample intervals, fail to consider differences in the inherent variances in grade of ore within the various strata established by using unequal sample intervals. Consequently the strata are sampled with different precision. This difference in precision of sampling between strata may account for much of the deviation between the plotted points representing actual field sampling data and the theoretical linear relationship between the amount of the difference between weighted and unweighted average grade of ore and the size of correlation coefficient between assays and sample interval lengths.

Jan 1, 1966

By Joseph J. Wallace

1. The investigation shows that nine coal beds have been mined in Harlan County, of which the Harlan and Upper Elkhorn No, 3 are the most important from the standpoint of present production. Of less importance are the Hindman, Flag, Haddix, Wax, Fire Clay, Armburgy, and Upper Elkhorn No. 2. The Harlan, Upper Elkhorn No. 3, and Upper Elkhorn No. 2 beds contain the largest remaining known reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 2,138 million short tons as of January I, 1932. Of this total, 1,956 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study, Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1954

By E. J. Matson

Under the investigation for critical and strategic minerals the Kaiser mine, formerly the Baxter fluorspar property, in northeastern Mineral County, Nev., was explored. The work comprised excavating 32 trenches averaging 90 feet in length, 8 feet in width, and 1 1/2 feet in depth. The trenches were excavated across the strike of the ore body to enable the engineer to spot the diamond-drill holes; 7 such holes were drilled, aggregating 3,276 linear feet. A total of 20 core samples and 107 sludge samples was taken. The work under this program indicated that the fluorspar southwest of the deposit extended laterally and also at depth at least 250 feet below the 400-foot level. INTRODUCTION The Kaiser fluorspar deposit is in the northeastern portion of Mineral County, Nev. Mining was begun about 1928, and the property has been a consistent producer of both Acid- and Metallurgical-grade fluorspar. The mineralized zone has been developed along a strike length of about 2,000 feet and to a depth of over 700 feet along the dip.

Jan 1, 1957

By James F. Devine

This Bureau of Mines report describes tests conducted at three sites to determine if, and to what extent, a vertical presplit fracture plane placed between a blast point and detection point will reduce vibration levels. Statistical analyses indicate that the presplit fracture plane did not reduce the vibration level.

Jan 1, 1965