Search Documents

By S. J. Hussey

Since the discovery in 1935 by Adams and Holmes that certain synthetic resins exhibit ion-exchange properties, many applications of the ion-exchange process have been made. There are two general types of ion-exchange resins. Cation exchange resins adsorb cations from solution, and these in turn may be replaced by other cations adsorbed under certain conditions. 'Anion exchange resins adsorb acids from solution, and the anion of the acid may then be replaced by other anions. It is reported, however, that certain anion exchange resins have a low capacity for anions of weak acids without the necessity of acid adsorption either directly or as an intermediate step. The adsorbed ions may then be removed from the resins by elution with an appropriate solution, and the resin is prepared for the next adsorption cycle by regeneration with another solution. Sometimes one solution, is used to simultaneously perform the functions of elution and regeneration. The first and probably the largest application is in the field of water purification. Other applications have been made in the production of high-quality foods for human consumption, in the recovery of valuable substances from solutions, in the separation or fractionation of electrolytes, and in several other fields, each of which has its specific applications, variations, and possibilities. Ion exchange resins also have been highly useful in perfecting techniques of laboratory analysis and research.4/, 5/, 6/

Jan 1, 1948

By S. J. Gerdemann

In support of its objective to improve mine safety, the Bureau of Mines has searched for better materials and systems to anchor roof bolts. TIlis report describes a study on the effects of mine waters upon accelerated gypsum, one of the materials under consideration. The accelerated gypsuw dissolved at an appreciable rate relative to an assumed 10-yr life span of a roof bolt. Surface orientation, initial ion concentration of a dissolving solution, and flow rate of the solu-tion had substantial effects on the dissolution rate. Factors such as water-cement ratio, accelerator content, wax capsule additions to the gypsum in cartridge-installed bolts, surface area, temperature, and curing duration had little effect. In an actual roof-bolt environment, dissolution will occur in static solutions to the solubility limit of gypsum (~2 giL) and cease, result-ing in minimal damage; but in flows of unsaturated solution as slow as 1 L per month, a loss of up to 10 pct will occur in 2 yr. Since miners cannot readily measure the flow or ion concentration of static-appearing water at every roof-bolt site, all such water must be assumed to be pure and flowing. It is recommended that gypsum-bonded roof bolts be confined to dry roofs only.

Jan 1, 1983

By M. J. Sapko

The U.S. Bureau of Mines has developed a portable meter for measuring the component concentrations in binary dust mixtures whose constituents have different optical reflectivities. The meter has been successfully tested with coal dust-rock dust mixtures taken from coal mines in Europe and the United States and fluorinated-carbon mixtures that change from carbon black to pure white during fluorination. Additional study has also substantiated the theoretical expressions used in the design of the meter.

Jan 1, 2010

By A. J. Kraemer, O. C. Blade

This report on the properties of commercial motor fuels sold in the United States is a continuation of a series of reports made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee of the Cooperative Research Council (C.R.C. ) and the Bureau of Mines of the United States Department of the Interior . The first report contained data on motor gasolines sold during the winter of 1935-364 . Further reports on motor gasolines sold during the succeeding summers and winters to the summer of 1941 have been issued . No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942 . The present report presents analytical data for 1,120 samples , representing the products of approximately 88 companies . As in previous surveys , these companies include both large and small suppliers . In addition, the Pacific coast is represented by data averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were received . Conforming to previous surveys , the data cover three groups of samplesregular - price , premium - price , and third - grade gasolines and each group has been averaged separately. The number of samples , items and brands comprising each group, exclusive of those of the Pacific coast, are as follows : Regular price , 641 samples , 250 items , and 64 brands ; premium price , 439 samples , 222 items , and 68 brands ; third - grade gasoline , 50 samples , 50 items and 19 brands .

Jun 1, 1943

This NIOSH Toolbox Training program contains 52 different modules designed to stimulate safety discussions among your employees. Each module is intended to be completed in roughly 10 or 15 minutes, so a Toolbox Training session can be conducted once a week for the entire year. Each session counts toward your employee’s 8-hour annual MSHA refresher training, thus saving an entire day of work.. The modules are used to refresh employees on the procedures, policies, and practices of working safely at a specific mine site and can easily be tailored to fit conditions and situations found on your property. Every module follows the same format, so that as the weeks pass, miners will start to approach every safety situation in the same way. A typical Toolbox Training session contains five basic steps that cover all the information in the module. 1. Identification of the hazard and discussions about the types of injuries typically associated with the hazard. 2. Discussions of some of the causes of the hazard. The MSHA example included with each module should be referenced. 3. After the hazard and accident has been explained and understood, discussions about best practices and tips for avoiding a similar accident. 4. Review of similar conditions or near misses from your mine site using the leading questions on the form to start a discussion. Specific examples of equipment or structures on the site that could lead to the same accident should be discussed. The blank space on the module is used to add your own remarks and questions to supplement the given information. 5. Miners fill out the training record on the back of the form with name, initials, and date of training session. The modules are designed to be kept in a standard three-ring binder and easily photocopied. This way, the same set of modules can be used for years to come. A blank form is included that can be used to create more Toolbox Training modules. The key component of Toolbox Training is to start a discussion among employees that will allow them to see the hazards around them every day and respond to these hazards in a safe and consistent manner. To start a discussion, ask questions that need more than a one-word response. Get the miners to talk about similar situations from their own experiences and give suggestions about how to fix the hazards around them. Toolbox Training is a quick and effective way to cover specific mining hazards, but it only works if miners are involved in the discussion.

Jan 1, 2004

By Wilbert J. Huff

[This is the fifth of a series of annual reports of the explosives Division, Bureau of Mines, United States Department of the Interior.3/ It deals particularly with work done during the period July 1, 1939, to June 30, 1939. The writer and the respective unit leader to whom credit is indicated have directed the various studies outlined.]

Jan 1, 1940

By W. W. Adams

Because of insufficient funds for printing, the Bureau of Mines was unable to publish its annual bulletin covering accidents at metal mines in the United States for the year 1933. A brief mimeographed summary of the principal statistical data for that year was released to the public late in 1934. Since then reports for 1934 have been received from the mining companies, and in order to avoid further delay in releasing this information to the mining industry and others interested in the prevention of accidents in mining, statistics for both years are presented in this publication with a minimum of interpretation and comment. The fatal-accident rate for the metal and nonmetallic mines (excluding coal mines) of the United States was more favorable in 1933 than in any previous year since 1911, the first year for which the Bureau of Mines obtained reports from the operators. Further progress was made in 1934, when the fatality rate was even lower than that of 1933. On the other hand, the nonfatal-accident rate, which had reached its lowest level in 1932, increased in 1933 and increased further in 1934, although not to such an extent as to prevent the rate for either of those 2 years from being better than that for any year previous to r1931.

Jan 1, 1936

By W. A. Stickney, J. W. Town

Studies on continuous - circuit leach - aluminum precipitation and leachelectrodeposition of mercury were made by the Bureau of Mines to determine optimum conditions and cost estimates for recovering mercury from mercury sulfide flotation concentrates . With 150 grams of sodium sulfide and 50 grams of sodium hydroxide per liter , from 98 to 99.8 percent of the mercury was extracted from flotation concentrates , with about 0.5 pound of sodium hydroxide used per pound of mercury produced . Precipitation of mercury from the caustic - sulfide solution with minus 8 - mesh aluminum shot required about 0.2 pound of aluminum per pound of mercury produced at a cost of $ 0.05 per pound of mercury . Electrodeposition cost with 7 mill power , based on 50 percent current efficiency , was below 2 mills per pound of metal deposited . Feed solutions ranged from 10 to 130 grams of mercury per liter , and current densities , from 2 to 70 amperes per square foot . The cost of open- pit mining 250 tons per day was estimated at $ 1.75 per ton , and flotation - leachingelectrodeposition of the ore , at $ 3.54 , resulting in a cutoff grade of about 0.1 percent mercury . The cost of underground mining 50 tons per day was estimated at $ 20.00 per ton , and the cost of milling the ore was estimated at $ 13.33 , which resulted in a cutoff grade of 0.6 percent mercury .

Jan 1, 1964

By O. C. Blade

"INTRODUCTION This report on the properties of motor fuels sold through service stations in the United States is a continuation of a series of reports made in accordance with a cooperative agreement between the Coordinating Fuel Research (CFR) Committee of the Coordinating Research Council (CRC) 3/ and the Bureau of Mines of the United States Department of the Interior. The first of these reports presented data on motor gasolines sold during the winter of 1935-36. 4/ Further reports were issued describing motor gasolines sold during the succeeding summers and winters to and including the summer of 1941. 5/ No reports were made on motor gasolines Bold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed. 6/The present report presents analytical data for 1,499 samples, representing the products of approximately 105 companies. As in previous surveys, the companies covered by the survey include both large and small suppliers. Conforming to former reports, the data cover three groups of samples - regular-price, premium price, and third-grade gasolines.As the number of analyses submitted for samples of third-grade gaso¬line are not considered adequate to represent this type of motor fuel, data for these analyses have not been averaged, but the individual items are tabulated. The number of samples, items and brands comprising each group is as follows; Regular-price, 872 samples, 266 items, and 83 brands; -premium-price, 584 samples, 217 items, and 72 brands; third-grade, 43 samples, 32 items, and 21 brands. The meanings of those terms as used in the surveys are as follows:"

Jun 1, 1945

By T. F. Mitchell, J. V. Batty, R. R. Wells, R. Havens

"INTRODUCTION )ne of the most important wartime activities of the Bureau of Mines was the search for new sources of minerals necessary to the prosecution of the war. As a part of the investigation of strategic mineral deposits in the United States under the Strategic Minerals Act (Public 117, 76th Cong., 1st Sess., Ch. 190), examining engineers of the Bureau of Mines investigated and sampled various deposits of chrome ore in California, Idaho, Montana, Oregon, and Washington, and those deposits that warranted further study were explored by diamond drilling, trenching, and drifting, as re¬quired. During these investigations, samples were submitted to the Ore Dressing Section of the Salt Lake City Station for metallurgical testing. This paper gives data summarizing results obtained from laboratory ore-dressing studies of the chrome ores submitted.Although the deposits range widely in geographical location, the mineral occurrence of all of them is strikingly similar. Chromium, in all of the ores tested, is present as impure chromite or chromium spinel. Although pure chromite (FeCr204 or FeO.Cr203) contains 68 percent chromic oxide, the iron may be replaced in varying amounts of magnesium, and the chromium may be replaced similarly by aluminum and ferric iron. In studying concentration methods as applied to chrome ores, the composition of the chrome mineral is of fundamental importance, because it is manifestly impossible to produce a high-chrome concentrate from a low-chrome chromite by any mechanical process.In all but one of the ores, the gangue material consists of olivine or altered olivine minerals such as serpentine, antigorite, and chrysotile. The exception, the Antelope or from Montana, has a gangue chiefly composed of actinolite, chlorite, and talc."

Jun 1, 1947

By K. R. Dorman

To develop the potential of precast concrete sets as a support medium in underground mines, a three-piece precast concrete drift set was designed for a small opening and tested to destruction in an underground straining frame. Thirty-six tests were made with three sizes of members using three different loading conditions. In addition, 14 members were tested individually in the laboratory. Test results are compared with theoretical calculations. A cost comparison shows the use of concrete sets would be advantageous where conventional wooden timber requires excessive replacement.

Jan 1, 1968

By F. M. Goodwin, John Campbell, G. W. Jones

"INTRODUCTION The investigation of the general hazards of combustible gases and vapors in manholes owned by the Edison Electric Illuminating Co. and the study of methods for eliminating these hazards, conducted by the Bureau of Mines, the Edison Electric Illuminating Co. of Boston, and the Boston Consolidated Gas Co. since 1929, was continued during 1933.From May and through December 1933 these tests were supplemented by a study of the manholes of the New England Telephone & Telegraph Co. The test crew was under the direct supervision of John Campbell, superintendent of the Special Service Department of the Edison Electric Illuminating Co., and F. M. Goodwin, vice president of the Boston Consol¬idated Gas Co.The procedure of sampling manhole atmospheres and of shipping the samples to Pittsburgh was the same as that used heretofore. In previous reports the relative explosibility of the samples was calculated by adding the percentages of the illuminants, hydrogen, carbon monoxide, methane, and ethane, dividing the total by 6.5, and multiplying by 100. Experience has shown that the factor 6.0 is more nearly correct; therefore, this has been used in calculating the relative explosibility of all the samples listed in appendix A and B of this report. If gasoline vapor is present a smaller factor must be used.ACKNOWLEDGMENTSThe cooperative investigation was arranged through the interest and effort of W. C. Bayliss, president of the Edison Electric Illuminating Co. of Boston; W. C. Beckjord, vice president and general manager of the Boston Consolidated Gas Co., and A. C. Fieldner, chief engineer, Experiment Stations Division, United States Bureau of Mines. Thomas H. Haines, superintendent, Distribution Department of the Edison Electric Illuminating Co., cooperated heartily in furnishing both men and information for the work."

Oct 1, 1934

By W. W. Agey

Under terms of cooperative agreements, the Federal Bureau of Mines Inter-mountain Experiment Station assisted the General Services Administration (GSA) in operating the manganese-ore purchasing depots at Deming. N. Mex., and Wenden, Ariz. A resident metallurgist stationed at the depots directed sampling of the ore lots for assaying, took samples for amenability testing, calculated acceptances for payments to shippers, and served as technical adviser to the depot manager. The Intermountain Experiment Station at Salt Lake City, Utah, tested the amenability of the ores to determine how much of the manganese could be recovered in concentrates assaying a minimum of 40 percent manganese (Mn) and containing a maximum of 16 percent iron (Fe), 15 percent silica (Si02) plus alumina (AI203), 0.3 percent phosphorus (P), and I percent copper (Cu) plus lead (Pb) plus zinc (Zn). All chemical analyses of the ores and test products were done at Salt Lake City. In all, 567 ore lots submitted to the Deming depot were tested by flotation to determine their amenability to concentration into specification-grade material; 421 lots were amenable, and 146 were unamenable, primarily because of high copper content or excessive silica or iron in the flotation concentrate. Chemical analyses totaling 42,700 were made on the ores submitted to the Deming depot and on the products of the amenability-test program.

Jan 1, 1959

By R. Vernon Helm

Four tables listing values for the various physical properties of those sulfur compounds most likely to occur in petroleum and petroleum products are given herein. The data necessary to bring the first compilation2/ in this subject up to date are given in table I -Revised and Additional Data, which includes boiling points, refractive indices, densities, and freezing points. Tables 11-, III, and IV are published for the first time and include refractive indices for the F, C, and G' lines of hydrogen and the helium D:3 line; surface tensions and viscosities, and refractivity intercepts, specific dispersions, specific refractions, and parachors. The need for information concerning the sulfur compounds in petroleum is becoming-more urgent because of the necessity of refining larger quantities of high-sulfur crude oil to meet the rising demand for petroleum products. For a number of years the Bureau of Mines has been engaged in research to make available more information concerning the properties of the sulfur compounds in petroleum. The petroleum industry has recognized the value of such studies, and as a result the American Petroleum Institute has established Research Project 48A to study sulfur compounds. The investigations under this Project are to be done in Bureau of Mines laboratories as a cooperative project in connection with the work already started.

Jan 1, 1949

By P. A. Hendricks

This U.S. Bureau of Mines (USBM) report identifies and evaluates factors responsible for metal/nonmetal (M/NM) underground mining accidents involving mobile equipment. Information regarding the occurrence and severity of the accidents, the type of equipment involved, the primary and contributing causes, and preventive measures is included. The goal of this report is to provide information that will aid mine operators and safety managers in the recognition of hazards associated with operating mobile mining equipment in an underground mining environment.

Jan 1, 1994

By L. G. Trudell, J. W. Smith, K. E. Stanfield

Representation of actual oil yields from sections of the Green River formation oil shales by two types of drill - cutting samples was evaluated . Average oil yields of single sets of mud cuttings from hydraulic rotary drilling in Colorado and gas cuttings from pneumatic rotary drilling in Utah were compared statistically with yields of core samples taken from adjacent holes . Oil yields from gas cuttings were identical to oil yields of core samples . Mud cuttings appeared to represent a section of the formation conservatively , the deficiencies increasing with increasing richness of sample . Because a large amount of the oil - yield data currently available for the Green River formation is based on mud- cutting samples , development of a valid correction method by additional testing is needed .

Jan 1, 1963

By A. A. Berk

The Bureau of Mines devised a test nipple for the field study of corrosion in the condensate-return lines of Federal heating plants. Corrosion surveys, made with this device, showed that the deterioration of the piping was caused principally by carbonic acid in the steam condensate. Corrosion problems were brought under control when the carbonic acid concentration in the condensate was decreased. In many instances, this was effected by decreasing the total carbon dioxide content of the feedwater; in others, the condensate acidity was neutralized with volatile, alkaline chemicals. Filming treatment with octadecylamine, reported successful in controlling return-line corrosion in industry, was much less effective in Federal area-heating plants. Laboratory study by the Bureau disclosed that octadecylamine is unstable in heating systems. Analytical methods were developed for this chemical and its degradation products in heating-plant condensate. Field surveys, in using these methods, confirmed the instability of the filming material. Laboratory tests showed that the degradation products are not useful film formers. Since filming treatment has little effect on condensate corrosivity, the piping was corroded where it was not coated by the treatment chemical.

Jan 1, 1962

By R. W. Stahl

A survey of firefighting facilities and practices in coal mines conducted by the Bureau of Mines3/ showed such variations in equipment and apparent attitude toward fire protection that a comparison with other industry seemed advisable. Although other industry is confined generally to surface operations and the hazards probably are not as great, the same general methods of extinguishment are employed, so that the cost and protection at least should be comparable. An investigation of industry other than mines revealed a generally greater emphasis placed on fire-combating equipment, fire-brigade training, fire-fighting facility inspection, and fire-hazard elimination, as well as a greater average expenditure for fire protection.

Jan 1, 1959

By Robert D. Ewing

The computer program described in this user's guide provides for the static, three-dimensional, linear and nonlinear analysis of structural and geological systems by the finite element method. The guide describes the capabilities and general features of the program and shows how input is prepared. A number of recent advances in finite element theory and computer technology are incorporated in the program. Nonlinear material properties are provided for, including isotropic, anisotropic, and time-dependent material properties, gravity loading, simulation of a sequence of excavation or construction, and a slip or joint element. The finite elements include beam, rod, axisymmetric and plane quadrilateral, hexahedron, thick shell, and axisymmetric and plane joint. The program also has an automatic mesh generator to minimize user input preparation for continuum finite element meshes.

Jan 1, 1976

By C. F. Winquist

The Bureau of Mines is engaged in research to evaluate the effects of cutter bit wear at coal mine faces. This paper addresses one element of conical bit wear, bit rotation. A discussion on mounting configura-tion and bit forces and their effects on rotation is presented. The effects on rotation and bit forces of bit attack angle, cutting depth, and skew are determined for two types of conical bits during linear cutting of sandstone-inclusive rock. The results indicate that a 10° negative skew angle and 35° attack angle produce the maximum rotation of 17.5° for each foot of cutting. Data on bit rotation and bit forces are presented in an appendix.

Jan 1, 1985