Search Documents

By R. T. MacMillan

Many bench-scale tests and studies have been conducted in developing and testing a chloride-volatilization procedure Ear treating low-grade manganese ore from the Maple Mountain-Hovey Mountain deposit of Aroostook County, Maine. The ore, averaging 10 to 12 percent Mn, contains manganese in several forms and is resistant to concentration or extraction by usual physical and chemical procedures. Over 90 percent of the manganese, content of the ore has been recovered using a chloridizing roast in which the ore was heated at 950°-9b0' C. in a circulating stream of hydrochloric acid gas. Chlorides of manganese and iron were volatilized and swept to a fume collector, where they were condensed and separated from the [as] stream. Operation of a small, 1-pound-per-hour shaft Furnace produced enough chlorides for studying other factors in an integrated process such as: (1) Conversion of the chlorides to oxides; (2) recovery of HC1 gas of suitable concentration Ear recycling to the chloridizer; and (3) control of the Mn-Fe ratio in the oxide product to produce a suitable feed for ferromanganese production.

Jan 1, 1956

By Sigmund Black

Ingersoll-Rand Research, T n c and the Lee-Norse Co. built a Bureau of Mines sponsored, special deep cutting continuous miner under this contract to study the effects of rotational speed and depth of cut on airborne respirable dust. After preliminary tests indicated and later verified that deep cutting - low rotational speed reduces airborne respirable dust, a series of underground tests were performed (9 combinations of rotational speed and depth of cut at 45° bit angle and 4" bit spacing). Additional data was obtained on specific energy, coal sizing and noise. The conclusions reached from the tests results were; a) deep cutting reduces airborne respirable dust generated and specific energy needed to cut coal., b) the greater majority of the decrease occurs in going from 1" to 2" depth of cut, c) lowering rotational speed has a particularly sizable effect of reducing the amount of dust at the operator's location, d) no significant relationship was found for either noise level or coal sizing to rotational speed or depth of cut. Recommendations include. a)) use of specific energy as an indicator of the change in dust level correlating to changes in cutting parameters, b) mine operators should acquire new deep cutting machines., since retrofitting would be selective.

Jan 1, 1977

By R. V. Higgins

Tarner (1),3/ Muskat (2), and Schilthuis (1) have presented methods of calculating oil recovery by the expansion of dissolved gas with and without return of gas to the reservoir. Although electronic computers have eliminated the tedious and time-consuming calculations (4) required by each of these methods, many petroleum engineers do not have access to electronic computers. For these engineers a short method is presented that uses the Tarner method as a base. Moreover, for engineers who have access to computers and have not as yet prepared a program, the short Tamer method requires less computer time than the long iterative methods. In the proposed short method, no plotting of the calculated data is required to determine a point of intersection described in the original Tarner presentation, as only one calculation is needed to determine the value sought, or two calculations if greater accuracy is desired.

Jan 1, 1960

By Horace C. Porter, F. K. OVITZ

The various fuel investigations that were being carried on by the technologic branch of the United States Geological Survey were transferred by law on July 1, 1910, to a new federal bureau, the Bureau of Mines, that was authorized to continue the investigations and make public reports of the results. In consequence of this transfer, the following report is published as a bulletin of the new bureau. The United States Geological Survey had been engaged in analyzing and testing coals, lignites, and other mineral fuel substances under authority given by act of Congress. This work, now centered at the experiment station at Pittsburg, Pa., had its beginning in the operations of the coal-testing plant erected at the Louisiana Purchase Exposition in St. Louis, Mo., in 1904. The results obtained at that plant showed that the work of determining the fuel value of the coals and lignites in the United States with a view to increasing efficiency in their utilization would be incomplete if it did not include systematic physical and chemical researches into the processes of combustion. Hence in its later investigations the Survey carried on such re- searches, concentrating attention on those lines of inquiry which promised results of greatest economic importance. This bulletin is a report on an investigation of the volatile matter in several typical coals-its composition and amount at different tem- peratures of volatilization. As the investigation is still in progress and will doubtless include other coals than those already examined, the bulletin may be considered a preliminary report, stating the prob- lems studied, the methods used, and the results thus far obtained.

Jan 1, 1910

By Leo A. Schrider

This report analyzes the successful low-pressure gas drive in the Keener sand of the Bonds Creek oilfield, Pleasants and Ritchie Counties, W. Va.) and predicts its future performance. Core analysis from two wells and electrical and radioactivity logs were used to evaluate the reservoir characteristics. Production records over a 37-year period indicate that over 240,000 barrels of oil have been produced from the Keener sand by low-pressure gas injection. Decline-curve analysis shows that 165,000 additional barrels should be recovered from 108 acres of productive sand by continuing this secondary-recovery method.

Jan 1, 1966

By John Ward Smith

This paper describes and evaluates a method that the Federal Bureau of Mines used to determine the ultimate composition of the organic material in 10 samples of oil shale from the Mahogany zone of the Green River formation in Colorado and Utah. Since interest has centered on the Mahogany zone, the richest section of the deposit, these 10 samples were chosen to provide a broad representation of this zone with the objective of obtaining generally valid ultimate composition values. The most probable organic composition for the Mahogany zone and the 95-percent confidence limits for each component average (in weight-percent of organic material) are: Carbon 80.5 ± .4 Hydrogen 10.3 ± .1 Nitrogen 2.4 ± .1 Sulfur 1.0 ± .1 Oxygen 5.8 ± .5 As only minor variations in composition were observed, the organic material of this particular bed is quite similar over a wide geographic area.

Jan 1, 1961

By Clyde E. Williams

[As a results of work conducted during the past three years, the Northwest Experiment Station of the Bureau of Mines, in cooperation with the University of Washington at Seattle, Washington, has developed a process for the production of sponge iron. Commercial operation of this process in a 3 to 4-ton scale has been so satisfactory that its use on a large scale (20 to 100 tons per day) can be safely considered. Description of Process. The process consists in passing a mixture of iron ore and coal through a rotating kiln heated at one end to a temperature sufficient to convert iron oxide to metallic iron, discharging, cooling, and separating the sponge iron from the residual coke and silicious material on a magnetic separator. Both the coal and the ore should be crushed to peso as 6-meth scream, tans producing particles finer then 1/12 of an inch. Seventy-five parts of coal or other carbonaceous material arc charged with every 100 parts of ore), This large amount of coal is required in order to supply sufficient carbon to maintain a strongly reducing atmosphere in the charge, but may be reduced to about 65 parts per 100 parts of ore by recovering and using tae carbon that remains in the discharge product. Large-scale operation and refinements in furnace design should lower this ratio to perhaps 56 or 60 parts of coal to 100 parts of ore.]

Jan 1, 1924

Objective: The Roof Monitoring Safety System (RMSS) provides a first step in roof behavior awareness. By understanding and measuring roof movement in an underground mine, the potential for injuries or fatalities to mine workers from fall of ground can be lessened. Also, officials at an underground mine with a history of data on roof movement are better prepared to make a decision on remedial actions if falls of ground become a problem. The RMSS provides a safer, simple, and inexpensive means for measuring roof movement.

Aug 1, 1998

By C. E. Jordan

The Bureau of Mines is conducting research into the pneumatic recovery of coarse mica and has used this method to produce mica concentrates that contain more than 90 percent mica. This research is being carried out pursuant to the Bureau's objective to develop technology that will help maintain an adequate supply of minerals and metals to meet national economic and strategic needs. Researchers used a Bureau-designed system of crushers, screens, and zig-zag air classifiers to concentrate coarse liberated mica particles from mica-bearing materials. This pneumatic system was used to concentrate four mica ores from Arizona, North Carolina, and South Dakota and three waste tailings from Alabama, Georgia, and South Dakota. Using these samples, it was demonstrated that plus 65-mesh size mica can be effectively recovered by the pneumatic method. Not only were the concentrates high in mica content; it was also demonstrated that this method can be used to recover up to 78 percent of the mica that was originally contained in the samples. Because it is a dry concentration method, the pneumatic beneficiation technique may be advantageous in areas where water resources are limited.

Jan 1, 1980

By W. R. K. Wu

This Bureau of Mines report presents a statistical study of the repeat abilities of coal-plasticity parameters obtained in the tests with the Gieseler plastometer and the Audibert-Arnu and Hoffmann dilatometers. Repeatability is expressed in terms of one or two standard deviations for the differences between duplicates. The statistical method employed here is summarized. Results are tabulated for the temperature and nontemperature parameters of the three tests.

Jan 1, 1970

By R. B. Tippin

The heavy liquid separation (HLS) process was investigated by the Bureau of Mines to develop a means of concentrating minerals from natural ores, Various spodumene ores were tested in a 0.4-inch diameter cyclone using pure tetrabromoethane (TBE) as the heavy liquid. Studies were initiated to examine the influence of (1) pulp density (2) feed grade, (3) cyclone pressure, (4) cyclone apex opening size) (5) cyclone vortex finder opening sand (6) mineral particle size on the separation efficiency. Each of these factors was found to affect the heavy liquid separation in some degree; the mineral particle size exhibited the greatest effect and the ore feed grade the least. Conditions necessary to yield an 85 percent spodumene concentrate with an 85 percent recovery were determined to be: 70 psig pressure, 10 percent solids, 0.08-inch apex opening, 0.11-inch vortex finder opening and a minimum amount of minus 200-mesh fines in the feed. Operation of multiple cyclones in series resulted in spodumene concentrates assaying over 90 percent and indicated mineral recoveries exceed-in 90 percent.

Jan 1, 1967

By J. R. Soule

"The fluorspar deposits in the Gallinas Mining District, Lincoln County, New Mexico, were examined early in February and again in April 1943 by the Bureau of Mines because of the possible importance of newly discovered deposits and of old mine workings showing fluorite-bearing material. There &re many of these deposits spread over a considerable area, and it appeared that exploration might indicate sufficient reserves to support a local mill that could contribute to the supply of fluorspar needed for war purposes. Accordingly, the Bureau initiated an exploratory program in June 1943, which was completed in August 1944.H. E. Rothrock, Roy Earhart, R. G. Smalley, and V. C. Kelly, geologists of the Federal Geological Survey, began mapping and studying the district in May 1943 and continued this work throughout the Bureau's exploration.David J. Stauffer, district ranger, U. S. Forest Service, and several claim owners assisted in the examinations and subsequent exploration.The fluorspar deposits in the Gallinas Mountains are reached by an unpaved forest road, which, leaves U. S. Highway 54 half a mile south of Gallinas station. The road runs due west for 3 miles, then turns due north just beyond the first cattleguard. This north branch is followed for 2 miles to a second cattleguard. There a left branch extends northwest up Red Cloud Canyon to the Red Cloud, and. All. American deposits; the right branch continues north for 2.miles past the Wade Porter ranch, to another left branch, which goes almost 2 miles west to the Hoosier Group deposits. The remaining deposits are reached by trail from either the Hoosier Group or, more easily, from the Red Cloud claim (fig. 1).The Hoosier Group is in sec. l9,, T.. 1S.,1 R. 12 E.; all of the other known ore occurrences are in secs. 13, 14, and 23 to 27, inclusive, T. IS., R. 11 E. All of the deposits are in the Lincoln National Forest and within the limits of a State game refuge. The nearest railroad loading point is Gallinas, Station on the Southern Pacific Railroad. Corona, the next station north of Gallinas, is a Mile or two farther from the deposits.Minor supplied, telegraph, telephone, freight, and express service, and limited living accommodations, Are, obtainable at Corona, 10 to 15 miles from the deposits of Carrizozo, N. Mex., 50 miles south."

Apr 1, 1946

By W. P. Diamond, J. R. Levine

The explosion hazard of methane-air mixtures has become an increasingly serious mine planning problem, and an advance assessment of methane gas potential can therefore be essential for a safe and economic mine development pro- gram. As part of its coal mine health and safety program, the Bureau of Mines has developed a simple, inexpensive test to measure the methane content of coal samples obtained from exploration cores. The gas content of coal per unit weight as determined by the direct method test can be used as a basis for a preliminary estimate of mine ventilation requirements, and to determine if degasification of the coalbed in advance of mining should be considered. Since the Bureau began measuring the gas content of coal samples in 1972, experience has led to equipment and procedural changes, the most significant of which has been the development of a ball mill for crushing the coal sample to release the residual gas at the end of the desorption test period. This revised procedure replaces the crushing box and graphical methods described in earlier Bureau publications. The results of 583 direct method tests are summarized in tabular form. These results include data on the gas content of 125 coalbeds in 15 States.

Jan 1, 1980

By Gus Pantages, Bernard D. Blaustein, Charles Zahn, Irving Wender

Oils from coal hydrogenation have been examined at the Bureau of Mines to learn whether any centers of the optical activity reported in coal would survive catalytic hydrogenation at 450-525 ° C and about 8,000 psig pressure , and , if so , to obtain information about the nature of the active products . Oils from carbonization tars also were examined . Optical activity was found in the majority of the distillate fractions of the hydrogenation oils and in almost all distillates from the carbonization tars . No activity was observed in the tar - acid and tar - base fractions examined . Methods for isolating optically active concentrates included distillation through a packed column , liquid chromatography on silica gel , and adduction with urea . For the materials so processed , the optical activity segregated mainly in the paraffin - naphthenic and the hydroaromatic fractions . Although the specific compounds responsible for the optical activity were not isolated , experimental and spectrometric findings indicate that alkylsubstituted cycloalkane , cycloalkene , and hydroaromatic structures are most likely responsible for the optical activity of the concentrates . The optically active centers probably derived mainly from the steroids and terpenes in the biological materials that participated in the formation of coal .

Jan 1, 1964

Reduce the dust exposure of workers in large processing buildings at mineral processing operations, using a total mill ventilation system.

Jan 1, 1994

By Jarrell C. Grout

The Bureau of Mines has developed a computer program for use in solving nonlinear regression problems. The program is written in a general form so that, regardless of the functional relationship, the unknown parameters may be evaluated by either the Gauss-Newton or the Newton-Raphson methods of iteration. Variances and covariances of the parameters, as derived from the law for the propagation of errors, are also determined.

Jan 1, 1969

Develop a portable emissions measurement apparatus to sample and measure tailpipe concentrations of diesel particulate matter (DPM), carbon monoxide (CO), carbon dioxide (CO2), nitric oxide (NO), and nitrogen dioxide (NO2) under steady-state engine load and speed conditions during a 1-minute test.

Jan 1, 1994

Objective: To develop and test a training program that enhances the hazard recognition skills of underground limestone miners. This program can help job performance and lead to enhanced safety in the underground workplace.

May 1, 1998

By Arno C. Fieldner

In view of the widespread interest in the production of synthetic liquid fuels from solid and gaseous fuels to supplement declining reserves of petroleum, and the many requests that are now being received for information on the subject, this bibliography of Bureau of Mines contributions has been compiled. In addition to the publications issued by the Government in printed or mimeographed form, references are included to articles written by the Bureau staff for the technical press and to cooperative reports of work done jointly with States, colleges, and industries. References are given under each section in chronological order. Bureau of Mines bulletins, technical papers, and Minerals Yearbooks are printed and are obtainable at the prices indicated from the Superintendent of Documents, Government Printing Office, Washington 25, D. C. If no price is given, the publication is out of print. The price of entire volumes of the Minerals Yearbook or of reprints of certain chanters may be obtained upon request. Any orders or remittances in payment for these publications should be cent directly to the Superintendent of Documents and not

Jan 1, 1945

Comparative tests of four coals used industrially for coke production have been made by three laboratories of the Federal Bureau of Mines, each using its standard equipment and procedures for evaluating coal for coking. Two of the coals were blends used in the western and eastern sections of the United States, the third was a strongly coking coal widely used for producing coke in Alabama, and the fourth was a blend typical of those used for producing foundry coke in the Birmingham district. The coals used and the cokes produced from them covered a wide range of chemical and physical properties. The tests used at all three laboratories for determining the physical properties of the cokes were made according to ASTM (American Society for Testing Materials) methods. The excellent agreement found for the physical properties of the cokes indicated that, for the coals tested, the BM-AGA (Bureau of Mines-American Gas Association) 18-inch circular retort used at Pittsburgh, Pa" the 14-inch slot-type oven used at Denver, Colo., and the 17-inch slot-type oven used at Tuscaloosa, Ala., were substantially equivalent for evaluating coals for production of coke. Thus, added value is given to data obtained previously and independently at these three Bureau laboratories. INTRODUCTION Laboratory equipment to produce coke for evaluation has not been standardized by the industry. The results obtained with anyone design of equipment have been regarded as showing only the relative values of coal to produce coke of the requisite quality. Few systematic studies have been made to correlate results obtained in different types of equipment. Results of one, in which the Bureau of Mines participated, were published recently.2/ This

Jan 1, 1961