Search Documents

By Donna L. Anderson

This U.S. Bureau of Mines report describes a system to determine the position and heading of a continuous mining machine during the maneuvers required at the face area of a mine. The system consists of commercially available angular position sensors and a computer interface developed and tested at the Bureau. The sensors employed are laser-based scanning devices that report the angular location of retroreflective targets within their 90° field-of-view. The targets are mounted on the continuous mining machine; the laser scanners are mounted on an external reference structure. The computer interface consists of a single-board computer-controller programmed to gather and process the angular position information, and to calculate the machine's position and heading relative to the reference structure. A sensor fusion algorithm will be incorporated into the computer interface programming to increase the accuracy and reliability of the system.

Jan 1, 1989

By F. P. Haver

Primary lead is produced in the United States by the pyrometallurgical smelting of lead sulfide (galena, PbS) concentrates, which poses sulfur dioxide and lead air pollution control problems. The Federal Bureau of Mines has investigated an alternative hydrometallurgy procedure that does not generate gaseous sulfur oxides and diminishes the potential for the escape of lead into the atmosphere. The procedure involves leaching galena flotation concentrates with ferric chloride (FeC13) solution to obtain lead chloride (PbC12) and elemental sulfur as expressed by the following chemical reaction: PbS + 2FeC13 ? PbC12 + 2FeCl2 + S°. At 100° C, over 99 pct of the PbS in the concentrate is converted to PbCl2 in less than 15 min. The leach solution, composed of brine (NaCl) containing slightly more than the theoretical required amount of FeC13, dissolves the PbC12 as it is formed, leaving a residue of elemental sulfur plus gangue. High-purity PbC12 (>99.9 pct) crystallizes from the leach filtrate on cooling and is electrolyzed in a low-temperature, fused-salt cell to obtain corroding-grade metal (>99.94 pct Pb). Spent leach solution (FeC12) is regenerated for further use by reaction with the chlorine obtained in the electrolysis of lead chloride. Other values, such as Ag, Cu, Zn, and S°, are recovered by additional treatment of either the leach solution or leach residue.

Jan 1, 1976

By William H. Hamilton

This report describes the results and conclusions of the development and evaluation of a unique concept for a lightweight air powered drill tool for probe drilling in anthracite mines. A concept model of the lightweight air powered tool was constructed and evaluation testing conducted at the Kocher Coal Company Porter Tunnel Mine. The unique anchoring method proved to be extremely satisfactory and the overall light-weight air powered drill tool concept proved feasible. Based on the results of the concept model testing, two prototype production units were designed and manufactured. These prototype units proved to meet all of their design requirements of lightweight, portability, drilling controllability, structural integrity and miner acceptance. The need for a better bit and drill steel system, however, became evident during the testing program and recommendations are made for further investigation and development of a bit and drill steel system suitable for this application.

Jan 1, 1979

By Sam S. Taylor

"INTRODUCTION This report deals with a comparatively simple application of some of the engineering principles involved in the evaluation, installation, and operation of air- or gas-injection projects and well-clean-out and repair methods to increase the producing rates of oil wells in partly depleted pools during the war. The methods suggested for developing gas-injection projects take into consideration that in general no new wells will be drilled because of wartime restrictions of equipment and manpower and that only existing wells and second-hand machinery will be used. Because air will be employed as the injection medium in secondary-recovery operations where natural gas is scarce and expensive, the disadvantages and hazards accompanying, its use are discussed. Engineering techniques recognized as best modern practice are discussed in relation to the effect of simple air-injection development of properties on postwar operations and Probable ultimate recovery of oil. The report is an introduction to where, when, why, and how an air-injection project should be installed and operated; it is not intended to be an engineering manual for technical guidance in the selection, development, and operation of simulative methods of oil recovery.The report is intended mainly for these thousands of operators in the Appalachian region owning a few wells prodding small quantities or oil daily. Many such operators are anxious to increase their production rates by simulative means and to rehabilitate their wells so that they will produce more oil to help win the war but, in general, are unfamiliar with secondary-recovery operations and cannot afford to hire technical assistance."

Sep 1, 1944

By Frederick H. Raab

An electromagnetic (EM) system for the location of trapped mine workers at coal-mine (300 m) depths has been developed. The use of such a system in deep mines (1-km depth) requires transmission at extremely low frequencies (ELF) and a reduction in the effective noise level beyond that which can be obtained by acceptable Integration times. Automatic-noise-cancellation (ANC) techniques reduce the effective noise level by combining several received signals that contain correlated noise. Such signals can be obtained either from a remote magnetic antenna or a local electric antenna. During Phase III of this program, real ELF noise data were acquired and used to test the ANC algorithms developed during Phase II. The ELF noise data were obtained from analog recordings made by Develco under another Bureau-of-Mines contract. Digitization was accomplished by an ND converter that was added to a GMRR computer. Phase III tasks Included preparation of software for digitization, computer-computer communication, data processing, and statistical analysis. Useable data were obtained from eleven half-hour tapes containing noise from one axis of the primary antenna and three axes of the remote antenna. The overall average Improvement in SNR was 4.1 dB. However, the average Improvements for the Individual X, Y, and Z axes were 4.2, 11.9, and -1.9 dB, which roughly follow the observed noise power. Nonlinear processing was not effective with this noise.

Jan 2, 1984

By D. Harrington

Along with other phases of mining , the ventilation of metal mines has been affected by the business depression of 1930. As might be expected , some of the results are favorable , and some are distinctly disadvantageous to progress . Probably the worst effect of the recession of mining activity is that , as usual , one of the first departments of almost any industrial establishment ( and this is especially true of mining ) to be curtailed is that which concerns what might be called welfare work , such as safety , health , etc. , and ventilation : in consequence , a number of men who were employed mainly on ventilation work in metal mines are now out of employment and their former duties either are being handled by others as only part of a crowded routine or are being allowed to lapse . On the bright side of the picture is the following paragraph from a letter by the ventilation and sarety engineer of the United Verde Copper Co. , Jerome , Ariz . , indicating that money and effort expended on ventilation during " flush " times give results which aid in money savings when depression comes : The desirability of absolute control over the ventilation system has again been demonstrated at this mine . Under full operation we have been using approximately 500 hp . to drive our big fan . Under curtailed operations we naturally do not require as much air , so by sending the air only where needed and airing out all other places periodically to keep timber , etc. , in good condition we have been able to economize in the quantity of air required . The fan speed has been reduced and the power dropped to 300 hp . , thus effecting a material saving in the power bill , and still maintaining an efficient ventilating system . "

Jul 1, 1931

By F. A. Penning

Improved skips, with lightweight cylindrical bodies, have made a significant contribution to advancing mine hoisting technology. New concept skips of aluminum bodies with rubber lining; fiberglas bodies with polyurethane liners have been designed and fabricated for field testing at an operating mine. New design, adjustable guide rollers have shown improved ride characteristics with noticeably less wear. Major reductions have been made in stress levels and stress concentrations. Field experience has shown the practicality of the approach. Guide alignment has been measured using the Guide Alignment Measuring System (GAMS). Analysis has been applied to interpret the data. Field measurements in an operating shaft and a test tower have shown the agreement in data from GAMS and plumb wires. Reproducibility has been demonstrated. The data are useful to realign shafts, to use as s maintenance tool, and to evaluate the maximum safe hoisting speeds. The surveys are made at several hundred feet per minute and the system is self-contained. Dynamics of skip-guide interaction has been analyzed using the computer program SKIP II. The effects of speed, weight, type of guides, kind of misalignment have been studied. Resonance has been demonstrated and factors that eliminate resonance have been identified. Data from the GAMS surveys are applicable to the SKIP II program. Interaction between the hoist rope and the mine conveyance has also been studied. Computer programs and closed-form solutions are presented. Economic impact of lightweight skips is presented for an existing mine and for a new mine. Reduction in rope size has a profound effect when using a lightweight skip for the same capacity. Increased productivity can be realized by keeping maximum rope pull the same while increasing skip capacity. Examples and charts project the significant savings in capital expenditure for new installations.

Jan 1, 1985

By J. R. Nettle

The purpose of these studies by the Federal Bureau of Mines was to determine the feasibility of refining low-grade hafnium by an inert-gas-shielded molten-salt electrorefining technique to produce a hafnium metal meeting reactor specifications. The techniques were adapted from those used success-fully for titanium electrorefining. Three electrolytes containing hafnium chlorides were developed from which deposits having a Brinell hardness of 170 or below were recovered. A KC1 + NaC1 + HfC14 electrolyte produced deposits in the hardness range of 140 to 165 Brinell. Deposits with a hardness range of from 132 to 152 Brinell were pro-duced from an electrolyte composed of KC1 + LiC1 + HfC14. A third electrolyte composed of NaC1 + K3HfC17 produced deposits with a hardness as low as 139 Brinell. In a fourth electrolyte, composed of NaC1 + K2HfF6, a measure of refining was accomplished, but under the test conditions no metal meeting specifications was recovered; none was softer than 174 Brinell. A number of metallic impurities were reduced in quantity by the electro-refining process, notably iron, which normally was reduced from 250 p.p.m. to less than 50 p.p.m. Magnesium generally was reduced from 680 p.p.m. to less than 80 p.p.m. Manganese content was also reduced by the electrorefining process. Sponge containing 90 p.p.m. Mn yielded deposits containing a maximum of 50 p.p.m.; some deposits contained only 10 p.p.m.

Jan 1, 1961

By M. M. Wong

The Bureau of Mines, under a cooperative research program with four lead companies, has investigated a nonsmelting process for the production of lead metal. The process, which would eliminate sulfur dioxide generation and minimize particulate lead emissions, involves ferric chloride leaching of galena concentrate to produce lead chloride, followed by molten-salt electrolysis of the lead chloride to yield lead metal and chlorine. This chlorine is used to regenerate ferric chloride in the leaching solution. The process was tested in an experimental unit with a capacity of 500 lb of lead metal per day. The tests were performed in three 10-day and six 5-day campaigns, during a period spanning 28 mo. The study was carried out using a southeastern Missouri lead concentrate. Typical lead recovery was about 98 pct. Process problems related to impurity buildup and control were studied. When copper and silver impurities were removed from the leaching solution, a lead metal purity of 99.999 pct was obtained. Lead-in-air levels and lead-in-blood levels of operating personnel were monitored. The process has potential for producing lead with minimum pollution, but is not ready for commercial utilization. Operation of a prototype commercial electrolytic cell and a full-scale pilot-plant investigation by industry are needed to evaluate the commercial viability of the process.

Jan 1, 1983

By J. S. Hansen

To improve mine safety, the Bureau of Mines has conducted a search for better materials and systems to anchor roof bolts. This report describes a study on the ability of a gypsum-based anchoring medium to withstand short- and long-term loads. Results showed that 2-ft-long bolts anchored with gypsum that was injected as plaster slurry at a 0.370 water-cement ratio and cured for 10 min sustained pull test loads equal to the ultimate strength of the bolt steel (about 37,000 lb). For comparison, the minimum required capacity is 17,600 lb. Long-term loads of 15,500 lb were sustained with estimated 10-yr movement of less than 1/2 in. Two-foot-long bolts anchored with gypsum installed in a cartridge in which the water was contained in tiny capsules sustained a pull test load of about 30,300 lb at a 0.319 water-cement ratio and 10-min cure time. At a 0.288 water-cement ratio, load capacity was about 37,000 lb. The lower load capacities of cartridge-installed bolts resulted primarily from the remnants of the water-wax capsules. Above 10,000 lb, creep movement of cartridge-grouted bolts appears excessive, but longer bolts may be capable of resisting creep better.

Jan 1, 1985

By T. M. Barczak

Longwall tailgates in coal mines are often subject to severe mining induced loading and deformation. Innovative tailgate supports have been developed over the years to provide safe and economical access and a ventilation pathway at the tailgate. The support capacity and yield capabilities of the supports need to be matched to the loading imposed by the surrounding rock mass. The ground response curve can be used to represent the rock mass response to mining and its effect on support systems. The FLAC finite difference code was used to supplement field results by simulating a longwall tailgate and the associated ground response. The ground response curve is developed by modeling tailgate excavations with different internal support pressures and recording the resulting convergence. Ground response curves are developed for two typical longwalls operating in the Pittsburgh seam with weak and strong immediate roof. An additional model is presented in which the effect of weak overburden strata is simulated. The ground response is shown to be significantly affected by the strength of the immediate roof as well as the main roof. The importance of yield capacity of standing support is demonstrated. Gob height and compaction are found to affect the amount of convergence in the tailgate. The potential exists to develop site specific tailgate design curves by combining model results with field observations.

By T. M. Barczak

A primary objective of the Bureau of Mines geomechanics research program is to develop a better understanding of support behavior and interaction of supports with the strata so that supports can be more closely engineered to the geological conditions in which they are employed. Four longwall shield supports were instrumented with an eight-transducer instrumentation array to measure leg, canopy capsule, and compression lemniscate link forces from which resultant shield loading was determined. The instrumented supports were monitored over a 4-month period, producing over 75 shield cycles of resultant shield loading. Resultant loading is the true measure of support resistance, providing both roof-to-floor and face-to-waste support reactions as well as the location of the reaction on the shield canopy. Observed roof support reactions were analyzed, with particular emphasis on horizontal shield loading, since it is the least understood design parameter. Average, peak, and change in shield loading during the mining cycle are discussed. Correlations among data parameters are examined, as is the distribution of support loading at the headgate and midface. Conclusions are drawn as to the effectiveness of the shield support at this installation. Recommendations are made for further research needs.

Jan 1, 1987

By W. E. Robinson

Differences in the composition or chemical structure of the organic material in samples of Uinta Basin (Utah) oil shale were studied relative to stratigraphic position within the Green River Formation. This involved a systematic study of the soluble organic material and the insoluble organic material (kerogen) present in the samples. Emphasis was placed upon the distribution of the alkanes (normal and isoprenoid compounds) in the soluble extracts and upon the aromaticity of the kerogen. Significant differences exist in the chemical composition of the organic material from various strata within the Uinta Basin, some of which were related to burial depth but most were related to source material variations, environmental differences, or other factors. The Uinta Basin samples differed significantly from Piceance Creek Basin and Green River Basin samples in the large amount of soluble extract they contained.

Jan 1, 1975

By J. R. Hoskins

This is the final report for Research Contract No. 00101300 (Min. 34) granted by the U.S. Bureau of Mines to the University of Idaho Mining Research Bureau. The research project is entitled "Development of Improved Ventilation Technology for Non-coal Mines and Other Underground Excavations.' The duration of the project was six calendar months, from 16 April to 16 October 1970. The budgeted cost was $34,867.00 of which $31,953.00 was to be furnished by the U.S. Bureau of Mines. The sequence of reporting that follows is to state the objectives as contracted, outline the program of investigation, highlight briefly the important technological factors peculiar to vein-type metal mine ventilation, and describe the normal methods of control. This is followed by the results achieved by the survey, and an itemization of the observed deficiencies in current technology. There follows a section dealing with the adopted Federal Regulations.

Jan 1, 1970

By David K. Ingram

The Bureau of Mines conducted underground mapping and rock strength tests to describe and analyze mine roof conditions surrounding ancient stream channel deposits (paleochannels) in the Pittsburgh Coalbed in southwestern Pennsylvania. Paleochannels in the study mine consist of sandstone and/or siltstone and affect the Pittsburgh Coalbed through erosion and/or differential compaction. Differentially compacted sediments within and adjacent to channel deposits caused slip planes, faults, clay-dike faults, clastic dikes (clay veins), coalbed rolls, and slumped structures. Paleochannels can be predicted by recognizing these features and associated sediments, which allows for modification of long-and short-term mine planning and development. Mine entries located beneath the paleochannel deposits exhibit less stable roof conditions than entries with normal (nonchannel) roof. Paleochannel deposits comprise only one-fourth of the mapped study area; however, they contain one-half of the hazardous roof. This study deter-mined that rock strength evaluations, including rock quality designation (RQD), unconfined uniaxial compressive strength testing, and point-load testing, must be accompanied by underground observations. Suggested remedial support techniques include angled and/or longer tensioned bolts, steel mats or crossbars, steel sets or cribbing, and roof trusses.

Jan 1, 1987

By G. S. Scott

Mine fires have occurred since the mining of coal was begun, and they are still occurring. The resulting economic waste may become considerable (219),3 especially if a fire is allowed to assume major proportions or to get beyond control temporarily. It is important, therefore, to act promptly whenever a fire is suspected and to have every action count. To do this effectively, it is necessary to know at the earliest possible moment and thereafter what is happening in a remote or inaccessible area. It is equally important to know before¬hand what may be expected as a result of any proposed combative measure. The logical method of combatting a fire demands the cooperation of both mining engineer and chemist. They should decide the course of action to be taken, drawing upon the mining engineer's intimate knowledge of the physical structure of the fire area, the cost and time required for proposed operations, and the probable efficiency with which they could be carried out, and upon the chemist's knowledge of the results to be expected therefrom.

Jan 1, 1944

By C. D. Messelt

The Bureau of Mines investigated the application of a diffusion model to sintering rate data developed for lithium titanium ferrite. The data were obtained by sintering pressed pellets under identical conditions for various times up to 11 hours. Stereological measurements were made on polished sections, and sintering rates were calculated. A model for intermediate stage sintering was fitted to the stereological data. This procedure produced a method by which these type data could be used to study the relative importance of volume and grain-boundary diffusion under a variety of sintering conditions.

Jan 1, 1979

By Franklin D. Cooper

This Bureau of Mines report reviews in detail the foundry coke situation in the United States in 1975. It discusses intrinsic production problems and identifies opportunities for modifying operating practices so that the quality and yield of foundry coke can be enhanced without unnecessary investment in new equipment. Major topics include operating data and attendant practices and problems, the relationship of carbonization phenomena to coke quality and yield, environ- mental impacts of foundry coke plant operations, suggested research and development opportunities, and data on components of oven charges and on foundry coke production and shipments.

Jan 1, 1977

By Danny Riley, Brian Curry, Sandya Govindaraju, James Bain

Acute vibration causes vasoconstriction in naïve human subjects1. Vibration-induced decrease in skin perfusion has also been reported in the rat-tail vibration model 2. After vibration exposure, rat-tail arteries demonstrate vacuoles in smooth muscle cells, similar to that caused by pharmacological vasoconstrictors3. This study addressed the effects of different frequencies, durations and patterns of vibration on lumen size and vacuole formation using the rat-tail vibration model in male Sprague-Dawley rats (~300 g). Methods The different groups were: 4-hr continuous vibration at 30, 60, 120 and 800 Hz; continuous exposure durations of 5 min, 1 hr and 4 hr at 60 Hz; and 4-hr cumulative exposure of 60 Hz delivered intermittently in cycles of 10 min on and 5 min off. Acceleration was set at 49 m/s2 r.m.s. for all frequencies. Unanesthetized rats were restrained in cages on a nonvibrating platform with their tails placed on a vibrating stage driven by a B&K motor (4809). The sham control animals were also placed in the vibration apparatus but not vibrated. Room temperature was controlled at 25 ± 1°C. Ventral arteries from proximal tail segments 7 were immersion fixed in aldehydes, embedded in epon-araldite and sectioned (0.5 µm) for morphological analysis. Vascular lumen sizes were measured as the percent ratio of the lumen perimeter to internal elastic membrane length using Image J software (NIH). The number of vacuoles in the smooth muscle layer of each artery section was counted. Results Fig 1: Semithin sections of arteries. A. Sham control. B. 4-hr vibration 60 Hz. In vibrated arteries, the lumen decreases in size, and smooth muscle cells (SMC) exhibit vacuoles (arrow). Bar equals 40 µm for each panel. [ ]

Jan 6, 2006

Introduction Research has shown that when an emergency occurs, work-ers often do not get the information they need to take appropriate action. Important information about incidents is either not com-municated effectively or not at all to those affected by the event. The "Emergency Communication Triangle" safety talk focuses on the content of emergency warning messages. It presents a procedure using mental cues that can be used by senders and receivers of emergency warnings. The talk includes graphics for use during the presentation, as well as references for more information. Background Interviews with 48 miners who had escaped one of three different underground mine fires revealed that warning information provided to them was inadequate. Either insufficient information was provided to miners inby the fire areas or they failed to ask the questions needed to let them plan and execute an effective escape. Most of the miners who evacuated from these three mines did not have information that would allow them to make decisions about efficient escapes. The communication breakdown came from two directions: (1) the individuals providing the warning did not offer details about the situations even though some were known and (2) the individuals who received the warnings did not ask for clarification of the situation. The lack of information allowed miners to continue attempting to place cues into normal frameworks after they should have evaluated the situation as abnormal and threatening. The uncertainty created by the lack of information influenced their decision-making and therefore their actions. Approach Researchers at the NIOSH Pittsburgh Research Laboratory have developed a training intervention that can be used by senders and receivers of warnings during a mine emergency. This material was developed for use in short safety training sessions such as start-of-shift safety talks. The information can be presented in about 15 minutes. Although the illustrations were taken from the underground coal mining industry, the training can be tailored to any work setting by substituting appropriate examples. How It Works During the safety talk, miners learn about the six categories of critical information that should be provided during emergency communications: Who, Where, What, Miners, Event, and Response. • Who: When reporting an emergency or receiving a warning, the first thing a miner must do is identify himself or herself. This is important because people react differently based on who gives them information. • Where: Giving or finding out the location of the problem is important. Of the 48 miners interviewed about their escape, only 2 knew where the fire was located. However, this information was known by either the dispatcher or the person who discovered the fire. • What: Miners must tell or ask exactly what is happening. At one mine fire, miners near the phone heard the message to evacuate and went to gather the others on their crew. One worker shouted to a machine operator: "Come on down to the mantrip. We're going out." Because it was close to quitting time, the machine operator thought they were just leaving the section a little early and went through his normal end-of-shift routine, wasting valuable time. After giving or obtaining the three initial pieces of critical information, miners can then give or obtain details about the response in progress. • Miners: Is anyone hurt? Has everyone been accounted for? When and where was a missing person last seen?

Sep 1, 2004