Search Documents

By S. H. Ash

THIS REPORT covers the third in a series of five projects into which the Conowingo tunnel system has been divided for geographical and practical reasons. It outlines the work constituting Project No.3 that consists principally of the following: (a) To sink the No. 15 shaft and extend the Alden, Sugar Notch, Baltimore No.2, and Laflin shafts from their present depths to tunnel level; (b) to drive a tunnel off these shafts to connect with the western end of the tunnel in Project No.1 (Lackawanna) and to a point 1 mile south of the No. 15 shaft; (c) to construct an emergency pumping plant at the No. 15 shaft, complete with 3 centrifugal pumps of 200-cubic-foot-per-second (c. f. s.) capacity each, and a discharge-water shaft and a discharge tunnel for conducting the water from the pumping plant into the Susquehanna River; and (d) to construct a lateral tunnel 1 mile long off the main tunnel in the vicinity of the No. 15 shaft, to be known as the Wyoming lateral. The project, as outlined, is a self-contained drainage unit that will permit unwatering inundated mines and safeguarding active mines in the Wyoming Basin of the Northern field and also will handle the water in the Lackawanna Basin, thus permitting the temporary pumping plant provided in Project No.1 to be discontinued. The pumps installed in the temporary pumping plant provided in Project No.1 can then be moved to the emergency pumping plants recommended in Projects Nos. 2 and 3, to be installed as the third or standby unit.

Jan 1, 1955

By Abdurrahman Cetinbas

The periphery of longwall panels in the Pocahontas No.3 coalbed is characterized by a zone of reduced permeability that inhibits the natural drainage of methane. A residual gas pressure of 105 psig was measured after 1 year in an isolated block of coal measuring 340 by 1,100 feet. The buildup of gas pressure within such large blocks causes methane problems during plowing operations. However, natural drainage holes drilled during development have been found to reduce the gas content of the coal in this coalbed by over 90 percent. The effect of water infusion on dust during plowing operations was investigated using existing methane drainage holes. These holes were cleaned of debris and a pipe was grouted into the hole for water infusion of the panel. Both total and respirable dust levels were reduced by 40 to 79 percent. Water infusion of the panel proved more effective than did the use of a plow-mounted spray system.

Jan 1, 1974

By W. R. Reed, J. A. Organiscak

Haul trucks have the potential to generate large amounts of respirable dust. This respirable dust has been shown to be a health hazard to personnel, especially if it has a high silica content. Lack of dust sampling data from haul trucks prompted the completion of a study to quantify respirable dust concentrations. These field studies were conducted measuring instantaneous respirable dust at stationary locations from passing haul trucks at a stone quarry and at a coal mine site. Fugitive dust levels from haul trucks were analyzed to characterize dust dispersion. This analysis indicates safe following distances for haul trucks and other heavy equipment to avoid overexposure of respirable dust from the lead haul truck.

By C. W. Owings

A few of the more progressive mining companies have taken precautions to safeguard employees or man-trips. Specially constructed men-cars -have been provided with special devices or mechanisms to stop the cars on slopes, if the hoisting cable should break. Cars have been equipped with safety chains to connect and hold them together if a coupling should break. Steel frames covered with heavy wire netting have been placed over cars to reduce injuries to the riders from roof fails on slopes. A safety cable passing from the front car to a point above the cable socket on the slope hoisting cable is used frequently as a precaution in case the socket loosens o the main cable breaks at the socket. Such devices are commendable, but the percentage of man-cars and man-trips protected is relatively small - entirely too small. Man-trips that travel level haulage roads are rarely protected safety devices, and haulage roads are seldom inspected by mine officials to determine the condition of roof and ribs.

Jan 1, 1935

By Eric R. Bauer

The U.S. Bureau of Mines, in cooperation with a southwestern Pennsylvania coal mining company, BethEnergy Inc., Mine No. 60, Eighty-Four, PA, recently assessed the feasibility of using pre driven recovery rooms (open entry recovery) when longwall mining to increase the productivity of the coal extraction process. Two recovery entries, one 200 ft long and another 600 ft long, were supplementally supported with bolts, channels, and wire mesh, and either fly ash-cement piers or fiber cribs, then mined into by the longwall face. The recovery entries showed little deterioration as the supports provided adequate resistance to the front abutment loading. Compared with conventional recovery methods, the fullface recovery room allowed for panel extraction to be completed nearly 17 days faster and to reduce face equipment move time by 1-1/2 days. The potential productivity increase accompanying recovery rooms is greater than the cost of supporting a fullface recovery room. The fullface recovery room provided over 18 additional production days and the opportunity to mine nearly 68,400 st of coal per year per panel mined.

Jan 1, 1989

By Richard F. Hewlett

Engineers at the Bureau of Mines Denver Mining Research Center have been a research program investigating the theory and application of mine sampling. Part of this program is an investigation of the efficiency of sampling methods that involves development of sampling-method theory through simulating ore-deposit samples and assays, using - electronic digital computer. Theoretical developments are checked against actual ore-deposit sampling, assay, and production data by the commonly used polygonal and triangular methods of computing grade and tonnage of ore reserves. To speed the computing procedures, a program has been developed utilizing a medium-size digital computer for computing ore reserves by the polygonal method. This program calculates nine prismoids per minute at a total cost of $0.21 per prismoid. The complete program, written for an augmented IBM 650 computer, is described in detail; it can be used without change for computing ore reserves for a low-grade deposit. Modifications necessary to convert the program to compute ore reserves for virtually any other type of deposit or grouping of ore horizons also are given; however, the program is limited to using only vertical drill-hole data.

Jan 1, 1962

By McHenry Mosier

The Bureau of Mines, United States Department of the Interior, has established a testing adit on the Government reservation at Mount Weather, Virginia, to facility to research on the fundamental tats of mining under actual metal-mining conditions. A number of sites in several Eastern States were investigated, out Mount Weather was selected because the rock seemed best suited for rock drilling and other mining tests and because the ground was already owned by the Federal Government, the site having been acquired in 1902 for use of the Weather Bureau. The testing edit has an advantage over en active metal mine for certain investigations because variable conditions affecting any particular research problem can be controlled and maintained in a fixed status, whereas in an operating mine this seldom is feasible. Operations were begin September 1935, with a crew of four laborers under a resident engineer. The laborers were recruited from, nearby farms, and. although they had no previous mining experience, they have developed into satisfactory miners.

Jan 1, 1939

On April 1, 1982, the Bureau of Mines and the Department of Energy entered into an Interagency Agreement to develop an enhanced computer cost model for uranium in situ leach mining. The original computer cost model contained data base information related to two regions; the Wyoming basin region and the South Texas trend area. The enhanced cost model contains additional information on San Juan Basin type deposits. This addition is significant because it expands the model's capabilites to include one of the largest uranium producing areas in the United States and developes costs related to uranium production from in situ leach mining. The data base was expanded and modified to include changes necessary for San Juan basin type deposits. These changes included, but were not limited to, state and local taxes, royalty payments, depth of deposits, drilling costs, and electrical costs. Also site visits were taken to verify many of the base case parameters. Consequently, the data base has been incorporated into the computer program and existing software was modified to provide for the additional data. Information was obtained on drilling coats and therefore the current program more accurately reflects these costs to depths of 2500 feet. This depth parameter has been expanded to include Wyoming Basin and South Texas scenarios also. Verbal communications were held with one operator in the Crownpoint, New Mexico area as well as the state regulatory agencies to help validate the expanded model. As a result of these changes, several tables have been included, summarizing changes in the new default parameters and the overall range of input parameters.

Jan 1, 1982

By G. K. Derby

Five different types of drilling systems were developed under the flexible drill program that was initiated by the Federal Bureau of Mines to protect roof bolter operators. The systems were designed for underground coal mines with seams as low as 30 inches, and with roof bolts longer than the height of the seam opening. Four of the developed systems were true flexible drills; the fifth was a remote-controlled, automatic rod changer concept. Only two of the five firms successfully completed testing requirements under the original contracts: BendixCorp.,4 with a true-flex drill; and Ingersoll-Rand Research, Inc., with the rod changer concept. The Bendix drill was rated best, and the Ingersoll-Rand drill was rated second. Because of the closeness of the ratings and the vast differences in the two development concepts, both systems had sufficient potential to justify further development funding for design updating and testing. Also, both systems warranted consideration for inclusion into other ongoing development projects under both safety and energy directed programs.

Jan 1, 1978

By R. R. Hornor, Geo. M. Hunt

The purpose of this paper is to point out some of the benefits and economies to be derived by the better selection , preparation, storage , preservation and utilization of mine timber , and to give some specific information on certain wood preservatives and processes suitable for mine timber preservation . The paper is based largely upon data obtained by actual experimentation and service tests conducted by the U. S. Forest Products Laboratory , Madison, Wisconsin, on wood preservation , covering a period of many years , and upon a field survey during the past summer by one of the mining engineers of the U. S. Bureau of Mines of some of the principal mining districts of Michigan , South Dakota , Montana , and Idaho , in which he made a general ' study of mine timber in metal mines , particular attention "being given to timber decay ; the conditions under which it takes place most actively ; the measures , if any , that are being used to combat it; and, finally, the advantages that might be anticipated in the use of chemically treated timber to prevent decay and thus prolong its life .

Feb 1, 1922

As longwall shields are lowered in preparation for advance, dust from the canopy falls directly into the air stream with the potential of becoming entrained. Historical dust sampling data from the early 1980s shows that shield advance contributed an average of 12 percent to the airborne respirable dust levels found on longwalls in the United States. Data from the 1990s indicates that shield dust liberation had increased to an average of 23 percent. Increased longwall production levels over this time resulted in the need to move a larger number of shields during each shift, while an increase in air velocities on the face was also occurring. These factors combine to suggest that greater quantities of shield dust are being entrained into the face air. A series of controlled laboratory tests were conducted in a test stand simulating shield dust entrainment to evaluate changes in airborne respirable dust levels at different air velocities. Significant differences in respirable dust entrainment were observed. The test facility, test methodology, and dust sampling results will be reviewed and discussed

This is the seventh in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the United States Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1.935-36.3/ The present report covering 1,87 samples represents the products of 83 companies plus those from the Pacific coast, which were averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were submitted. For the regular grade 985 samples consisting of 73 different brands are averaged. The premium grade consists of 489 samples of 40 different brands. The third grade has 401 samples averaged from 51 different brands. In this report the districts have been reduced to 21 by combining North and South Texas into one district. El Paso samples are reported with the South Rocky Mountain district, and. Amarillo, Tex., has teen included with the Middle Rocker Mountain district. In the present survey samples from Fort Smith, Ark., have been included in the Tulsa area, Indianapolis has been included in the St. Louis district. Cleveland represents the State of Ohio. Samples from Little Rock, Ark., and North Carolina have been included in the Memphis district. The Pittsburgh district includes samples only from this State and Wheeling, W. Va. The actual sampling points in each area are indicated on table 1.

Jan 1, 1939

This is the seventh in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the United States Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The present report covering 1,875 samples represents the products of 83 companies plus those from the Pacific coast, which were averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were submitted. For the regular grade 985 samples consisting of 73 different brands are averaged. The premium grade consists of 489 samples of 40 different brands. The third grade has 401 samples averaged from 51 different brands. In this report the districts have been reduced to 21 by combining North and South Texas into one district. Fl Paso samples are reported with the South Rocky Mountain district, and Amarillo, Tex., has been included with the Middle Rocker Mountain district. In the present survey samples from Fort Smith, Ark., have been included in the Tulsa area, Indianapolis has been included in the St. Louis district. Cleveland represents the State of Ohio. Samples from Little Rock, Ark., and North Carolina have been included in the Memphis district. The Pittsburgh district includes samples only from this State and Wheeling, W. Va. The actual sampling points in each area are indicated an table 1.

Jan 1, 1939

By Meherwan C. Irani

The Bureau of Mines is developing a new technological approach to handling the problems of fires in abandoned coal mines and waste banks. This new technology involves the accelerated combustion of "waste" coals in place (i.e., in situ) under controlled exhaust ventilation conditions, which allows for total management of the combustion products; including utilization of the heat produced" This new concept could significantly lower the costs of reducing the environmental and public safety hazards associated with waste coal fires, and could lead to the conversion of a coal waste to a coal resource. The controlled burnout technology has progressed from the laboratory stage to a full-scale field evaluation stage at the site of an abandoned-coal-mine fire. This first report describes the site selection, evaluation, and preparation, and the design and construction of the full-scale controlled burnout installation. Subsequent reports will deal with the results of the operational field trial.

Jan 1, 1983

By Robert E. Green

This Final Report summarizes the results of work accomplished under Contract No. J0215039. It is in an executive overview or executive summary format. The number and description of the various technical reports prepared and submitted is outlined. The essential changes and reasons for the revised program schedule/contract modifications actually enacted in May 1982 are discussed in detail. The evolving mines/deposits list and the accompanying criteria classifications are explained along with the verifications/justifications for adding or deleting specific mines/deposits to the list. Difficulties and problems experienced during the different phases of the project in conjunction with the ensuing remedies are highlighted. The final section of they report is devoted to presenting Davy McKee's suggestions for improvements to future MAS commodity studies. Appendix I is comprised of three of the evolving mines/deposits lists starting with the original RFP list and ending with the final completed list. Appendices II and Ill are tabulated summaries of property data including reserves/resources, assays, production, and operating costs. The figures for the specific mines/deposits are given in "range of values" so as to protect the confidentiality of the individual owners/ operators.

Jan 1, 1983

By K. Hanna

This U.S. Bureau of Mines report describes a rock mechanics instrumentation program conducted in a shallow underground coal mine in central Illinois. This research program was designed to provide a basic understanding of the structural behavior of entry intersections. A wide variety of instruments and measurement techniques including hydraulic borehole pressure cells, multiple-point borehole extensometers, roof bolt compression pads, and overcoring were employed to monitor roof stresses, pillar loading, strata movement, floor heave, and bolt loading before, during, and after intersection development. A summary of intersection design theories, failure modes, and support techniques is included and instrumentation installation procedures and analysis methods are presented. The study identified two critical parameters that affect intersection stability: in situ horizontal stresses and geological discontinuities. Important design parameters for improving intersection stability are roof span and intersection geometry.

Jan 1, 1991

By J. J. Dowd

1. The Pittsburgh bed is the most important bed in Brooke County and virtually the entire production of coal in the county comes from this bed. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 191 million short tons as of January 1, 1954. Of this total, 190 million short tons are in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By Northcutt Ely

This volume summarizes mining and petroleum legislation in 22 jurisdictions of the Near East and South Asia. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes : First, identification of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis of the laws governing mines and quarries and their products; and third, analysis of laws applicable to natural gas, petroleum, and related materials. Where pertinent, sections dealing with historical background or administration have been added. In countries where minerals are subject to control of states or provinces, those areas are considered separately from the central government.

Jan 1, 1972

By W. H. Schiffbauer

NIOSH has developed an active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) for warning workers as they approach known dangerous areas around heavy mining equipment and other dangerous work zones. HASARD is composed of a transmitter and a receiver. The transmitter generates a 60-kHz magnetic field using one or more wire loop antennas. Each antenna is adjusted to establish a magnetic field pattern for each hazardous area. The receiver, worn by the worker, is a magnetic field strength meter. The received signal is compared against preset levels which are calibrated to identify levels of danger. The receiver outputs can include visual, audible, and vibratory indicators and it can also be made to disable machine functions. HASARD was field tested on a Joy 12 continuous miner, a Komatsu 210 M Haulpak, and on a highwall launch vehicle. Slight modifications were made for each application. HASARD provided warnings as designed and proved to be rugged enough to withstand the harshest of production environments.

By Elaine T. Cullen, Thomas W. Camm

The mentor/learner model is a time-honored approach to teaching, including within the mining industry. Miners know when they see excellence and have a deep respect for experts in their field. By using expert miners as mentors to other, less-experienced miners, training programs can be developed that will have a legitimacy and credibility that resonates with those being trained. Building upon concepts in current theories of adult education, this paper highlights the unique advantages of using mentoring as a teaching method that can make the educational experience both interesting and effective. Current NIOSH safety training materials use these concepts to deliver effective adult learning experiences for workers in the mining industry.

Jan 1, 2002