Search Documents

By Darren Thorton, David Sprott, Ian Brunton

Blasting causes movement of the rock and can be detrimental to the accurate delineation of the ore and waste regions within the resulting muck pile. The consequences can be ore loss and dilution. However, ore loss and dilution can be minimized and significant increases in profit can be realized if the movement can be accurately measured. Various methods have been used to measure muck pile movement including poly-pipe, chain and sandbags but these have been either inaccurate or impractical. The Julius Kruttschnitt Mineral Research Centre, JKMRC, has developed an electronic blast movement monitor that provides accurate three-dimensional movement vectors following a production blast. From this information, the ore block boundaries in the blasted bench can be adjusted to compensate for the measured movement and then ore recovery can be optimised. Following initial development of the prototype technology, the JKMRC further developed and demonstrated the system in actual production blasts at an open pit gold mine operated by Placer Dome Inc.

Jan 1, 2005

By Stephen Mansfield

In metalliferous mining operations, subdrill is that portion of the blast hole that is drilled below the target grade elevation, and in most cases loaded with explosives. Its primary aim is to enable efficient excavation down to the target floor level. Subdrill is often described as being expensive and that excessive subdrill should be avoided, as it can result in damage to the subsequent floor, lead to difficult drilling conditions and higher vibration levels. As a result, many operations aim to apply the bare minimum amount of subdrill in order to excavate to the target floor. At a large open cut copper operation, challenging geological structure resulted in slabby and blocky fragmentation in the stemming region, resulting in poor crusher throughput due to bridging. To overcome the poor fragmentation in the top of the bench, longer than conventional subdrill was used to precondition the top third of the bench. The technique significantly improved the run of mine fragmentation and resulted in feed to the in-pit crushers that is more consistent, which produced less crusher downtime due to bridging. A new method of quantifying the energy in a blast has been created. Termed the linear powder factor, or energy factor, the calculation considers the energy contributed by the subdrill of the upper bench and its impact on the energy in the lower bench. The technique enables blast designs to be optimised to deliver finer fragmentation and more consistent blast outcomes. To support the layer of preconditioned rock at the top of the bench, an innovative new device was developed. The device is inserted into the drill collar immediately after drilling and remains in position throughout the subsequent steps of hole depth measurement, priming, loading and removed prior to stemming. The device not only supports the broken rock at the top of the bench, but also minimises the amount of drill cuttings that fall back into the hole. Furthermore, the device helps protect the hole from damage by external factors such as weather events, drill tracks, vehicle tyres and movement around the collar during measurement and loading of the blast hole.

By Carl Lubbe, Ron Frye, Wayne Curtis, Julie Pecori, Dan Leach

Blasting conducted in the USA using the new Electronic Initiation System developed by Altech has shown that an accurate delay system will benefit the customer. Results from test work clearly showed that improved fragmentation was effected and blast vibration was at least similar to that currently found at the test venue with improvements possible.

Jan 1, 1997

The objective in controlled blasting is to reduce overbreak to control the final pit wall slope, shaft, drift ditch, bench, etc. to the final planned excavation limit. The six main types of controlled blasting utilized today are: 1) Line Drilling 2) Cushion Blasting 3 Smooth Wall Blasting 4) Buffer Blasting 5) Presplitting or Preshearing 6) Air Deck Presplitting

Jan 1, 1992

By Nolan Eckroade, Nigel Pereira

Wireless electronic blasting systems are a new technology that enable truly wireless initiation through rock, air and water. This is achieved using low frequency magnetic induction waves to wirelessly send a firing command to groups of in-hole primers. Fully wireless initiation not only removes the limitations imposed by a wired connection to each primer in a blast, but also enables users to alter the paradigm of conventional mining techniques to advance operational productivity and reduce personnel exposure to high-risk activities. While initially deployed in underground applications, wireless electronic blasting is now being used in the open cut environment. To capture the early impacts in surface mining operations, case studies conducted at three surface mines evaluated blasts utilizing a wireless electronic blasting system against baseline blasts using conventional, wired initiation systems. The purpose of this paper is to outline the specific learnings associated with wireless electronic blasting in surface mining to date. The paper will include references to these specific case studies as well as benefits realized and applications for the future.

By Mike Boissonneault

It was three years ago when the “storm of the century” had taken a firm grip over the Pacific West Coast and inland areas. At the Big Sky ski resort in Montana on Christmas morning two ski patrollers set out to perform an explosives “hand charge” avalanche control mission that would see only one return. It has been difficult to determine exactly what happened. Investigators do know that there were three separate and consecutive attempts to light a safety fuse, when it had apparently been burning since the first attempt. Time ran out after the third attempt. Although this accident has had a profound impact on North American avalanche control programs, I am sure it pales in contrast to the shock and grief experienced by family members who lost a loved one.

Jan 1, 2001

By Gordon Revey

The challenge of managing blasting risk, types of risk, public perception, and a system for managing risk were covered in the first part of this article in the May/June 2000 issue of the Journal of Explosives Engineering. This final part of this two-part series provides a method for identifying specific blasting risks and reviews the importance of community relations.

Jan 1, 2001

By Marcia Harris, Richard Mainiero, Michael Sapko

Since 1988, there have been 17 documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through ground strata into occupied enclosed spaces as a result of proximate trench blasting or surface mine blasting. These incidents resulted in 39 suspected or medically verified carbon monoxide poisonings and one fatality. To better understand the factors contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out studies in a 12-foot diameter sphere to identify key factors that may enhance the levels of CO associated with the detonation of several commercial trenching explosives. The gaseous detonation products from emulsions, a watergel, and ANFO blasting agents as well as gelatin dynamite, TNT, and Pentolite boosters were measured in an argon atmosphere and compared with those for the same explosives detonated in air. Test variables included explosive formulation, wrapper, aluminum addition, oxygen balance, and density. Major contributing factors to CO production, under these laboratory test conditions, are presented. The main finding is the high CO production associated with the lack of afterburning in an oxygen poor atmosphere. Fumes measurements are compared with the manufacturer’s reported IME fume class and with the Federal Relative Toxicity Standard 30 CFR Part 15 in order to gain an understanding of the relative toxicity of some explosives used in trench blasting.

Jan 1, 2003

By Alastair Grogan

In October of 2002, the author was retained by Public Works and Government Services Canada, on behalf of the Department of National Defense, to design, construct and test the effectiveness of a bubble curtain system at an underwater demolition range, near Victoria, BC. The purpose of the bubble curtain was to reduce the potential for fish mortalities at the site. This paper presents some of the elements of the design, along with the results of overpressure monitoring during blasting and compares the results of fish mortality and animal behaviors with and without the bubble curtain in operation.

Jan 1, 2005

By John A. Franklin, Tom C. Palangio, Norbert H. Maerz

WipFrag systems I and II have become the world standard in photoanalysis systems to measure fragmentation. Mines, quarries and excavating contractors can now easily measure blast results and track the progress of optimization efforts. This technology was developed and evolved to allow automatic measurements of the size distribution of patiicles on moving conveyors, in truck boxes and on crusher feeds. Production machinery can now be controlled by photoanalysis results and multiple cameras allow various locations to be monitored by a single system. Blast designs can be monitored on a shot by shot basis. Changes in delay times, explosives, patterns and hole sizes can be quickly evaluated. Along with this measurement capability has come a heightened awareness of the importance of “optimum size” and uniformity of particles for lowest cost production and material handling efficiency. In the past, savings in the “drill / blast” cycle of the operation were sometimes overshadowed by downstream production costs related to fragmentation. Now total production costs can be compared with fragmentation sizes which will immediately show the trend towards optimum size for economical production. No cost reduction program can be complete without this critical information.

Jan 1, 1997

By David G. Borg

"Although researchers have realized varying degrees of success in numerics modeling, computer blast simulations and small scale in-situ testing, most will agree that the greatest uncertainty in total success stems from the uncontrollable field variables. Given the diverse nature of field conditiorencountered, no reliable and proven method of evaluating fragmentation quantitatively, and the lack of adequate field controls found in many operations, it is unlikely that a universal plug-in model will be developed for all blasting in the imediate future. This does not imply that all research devoted to modeling should cease, for it is precisely here where more research efforts are desperately needed."

Jan 1, 1989

By Rowan A' Murry Karstel

One way to ensure dragline productivity is by Increasing the size of the dragline bucket. In August 1994, Optimum Colliery in conjunction with Van Reenen Steel, Northwest Applied Technology, SSAB of Sweden and Barlows Equipment launched the new lightweight dragline buckets. Optimum built the first prototype bucket that was used for the deslgn for future buckets. After knowledge had been gained from measuring the input force of the bucket Northwest Technologies designed the new bucket with finite element analysis. Together with the knowledge of quenched and tempered steel from SSAB of Sweden and Barlow Equipment, the new Wrightech bucket was born.

Jan 1, 1998

By Brian Stump, David Anderson, D. Craig Pearson, Robert Martin

Mining explosions designed to move, bulk or fracture rock are often composed of a number of explosions arranged in a complex spatial and temporal pattern. The effects of the explosions are strongly dependent upon the design and implementation of this blasting pattern. This paper describes the collection, combination and visual display of multiple types of data from these explosions for the purposes of understanding the relationships between the blast design, implementation, and observations. Data sets consist of three-component ground motion, acoustic, video and high speed film, three-dimensional topography, geological and geophysical properties, design blast pattern and timing, and velocity of detonation in the explosive for individual borehole detonation times. The explosions studied include simple single-fired contained explosions, ones designed to bulk and fracture rocks and those that cast material.

Jan 1, 2000

By Henry S. McDevitt

External Shock Mitigation (ESM) is being studied as a possible means of retrofitting existing buried structures to provide additional protection from ground shock. As part of this study, two tests were conducted on four ESM models and a control structure. The test articles were placed at a carrnon distance and subjected to the ground motions created by a buried explosive charge consisting of 2,ODO pounds of nitranethane (NM). Adequate instrumentation data were obtained to assess the response of the four ESM models. The assessment relied heavily on direct comparison of horizontal motions measured in the models, with similar measurements in the control structure. From the tests, it was observed that peak accelerations were reduced by a factor of 5 by the ESM. However, the particle velocities and displacements were not significantly affected by theEIS.

Jan 1, 1997

By Kush Patel, Gary Cavanough

Mining operations consume over 2.5 Billion Australian dollars’ worth of bulk explosives annually (Richardson, 2018). Despite the large volume of product used, current practices only conduct a cup density test of the product being used. Explosive products are made up of a number of components, each with an effect on the performance of the explosive. This paper presents methods currently available for the evaluation of bulk explosives and discusses the results of the evaluation of bulk explosives using each of the methods. Through the preliminary experimental analysis, wet chemistry and the Bulk Explosive Analyser were found as methods most suitable for the evaluation of bulk explosives. This paper also presents data obtained from the experimental comparison of the wet chemistry method and the Bulk Explosive Analyser. Through a total of 60 tests carried out on 10 different bulk explosive products the average error of each method was determined, the BEA presented an average error of 0.11%, whereas, the wet chemistry method presented an average error of 1.90%. This is a significant difference when considering the importance of formulation of explosives. Further investigation into the capabilities of the BEA are also presented in this paper.

By Larry Schneider

I n the simplest application of a shock tube initiation system, the tubing acts as a “relay line” which passes a detonation signal from borehole to borehole. When the signal arrives at each borehole, it causes the detonator attached to it to fire. Such a single path constitutes a progressive series where each unit must function properly in order to activate the following units. Any application error, malfunction, or mistake in connecting any surface unit will stop the progression of the detonation signal through the system and result in a “cutoff” or misfire of the following charges.

Jan 1, 1995

By John E. Wiegand

"We will attempt to explain the basic workings of a modern seismograph and how the recorded data can be interpreted, not only for determining compliance to the regulations, but also in determining whether or not a seismograph record is accurate and valid. We will discuss some parameters that should be included in all seismographic recordings. We will give examples and use overhead slidesto show examples of both accurate and valid recordings, and tampered and inaccurate seismograph recordings. Much of the information presented will be basic in nature, and will reflect the opinions and personal experiences of the author. We ho'pe the listener will gain valuable information concerning the use and interpretation of seismographic data, as well as find interest and sometimes humor in the examples shown."

Jan 1, 1992

By Laura Bastemante, Bruce Vandenberg, Fred Huettig

Recent advances in solid-state, field portable, fast framing video camera systems and PC based frame capture hardware now allow blast imaging up to loo0 frames per second. Up to 8 seconds of data can be stored directly into the unit, downloaded to a PC or archived to a standard VCR without data compression. Since no film processing is involved, motion analysis can be performed instantly and on-site within a few minutes. This paper will describe the design features and applications of the KineView 1256P system and compare these with the analogous aspects of film based cameras.

Jan 1, 1997

By D. J. Leidel

The offshore production of oil and gas resources has been active in the Gulf of Mexico since Kerr- McGee drilled the first commercial well out of the sight of land in 1947. Since then, approximately 60% of the offshore oil/gas production structures used globally have been erected in the GOM to support the production of energy resources’. The shallow, shelf and shelf edge waters of the Gulf of Mexico have reached or are rapidly approaching production maturity, requiring that the fixed structures used to support energy production be removed or otherwise disposed of by suitable means. The use of energetic materials has been determined to be a safe, efficient and cost effective technology to remove fixed offshore structures whose service life has been exceeded.

Jan 1, 2002

By Conny Postupack

The first principle one usually learns about blasting is that competence in this field is best gained by experience in making blasts rather than by reading a book or by listening to a lecture. The reason for this is that there are a large number of variables affecting blasting results and not all of these can be accounted for by a few rules or a few sets of equations. Even an experienced in a new area, may have co make one or two himself to the new conditions with which he blaster when operating shots just to acclimate is faced.

Jan 1, 1991