Search Documents

By A. W. (Sandy) Neilson

Whether you are a general contractor who hires subcontractors to perform blasting work or you have your own blasting crew, it is extremely important to understand how Business Liability Insurance works, regardless of who is ultimately providing the coverage. If close attention is not paid to the limitations and preblast survey requirements under most policies that provide blasting coverage, you could find yourself facing an uninsured loss.

Jan 1, 2002

By James D. Cook, Dan McCutchen

Effective overburden casting requires the efficient use of todays explosives and initiations systems if a mine is to survive. This paper uses a major coal stripping operation as an example of the proper application of explosives and initiation system to their conditions.

Jan 1, 1994

By Jeffrey E. Loney, Andrew F. McKnown

Recovery of contaminated groundwater migrating through bedrock can be very difficult due to the low transmissivity of many bedrock fracture systems. To overcome these difficulties, a system of controlled "trench" blasting has been used on several projects to assist in cutting off and collecting groundwater plumes in bedrock. By using a combination of trench blasting and presplitting techniques, linear "fracture" zones are created in appropriate locations to significantly increase flow into recovery wells and control plume migration.

Jan 1, 1995

By Jack Eloranta

Proper selection of stemming has a profound effect on blast performance. This paper describes several methods of evaluating stemming performance in 16-inch blastholes. Tests are done on stemming ranging in size from nominal 1/4" crushed rock up to railroad ballast size rock (2 1/2" > diameter < 3/4"). Concrete plugs (both pre-cast and poured) are evaluated as well as air decking.

Jan 1, 1994

By T. N. Singh, Vasudev Singh

To explore and exploit the natural resources like oil, gas, economic mineral water drilling is still considered to be the reliable and economical method. When a drill bit penetrates the rock mass either by percussion or by rotary and may be some times a combination generates stress and thrust on the rock mass as well as on the drill bit. The strength and hardness of the rock govern the life of the drill bit and its runnage. Physico- Mechanical properties of rocks have great influence on drillability. It is observed that higher the strength of rock, reduce the life of the drill bit while drilling, ultimately decreases the drillability. An attempt has been made in the present paper to establish relation among various physicomechanical properties i.e. uniaxial compression strength, tensile strength, shear strength, Schmidt hardness and abrasivity with drillability of different rock types. The specific energy of each rock type has been calculated using micro-bit drilling. The rocks from different lithological succession were collected. The rock specimens were prepared according to the norms of International society of Rock Mechanics (ISRM).

Jan 1, 2008

By John T. Watson, Jim Bailey

Increasing public awareness is probably the single most important challenge faced by any blasting contractor today. This increased awareness usually results in an outcry for tighter regulations and restrictions on those in the blasting industry. Those affected do not often understand the dynamics of blasting and are simply fearful of the unknown. This reaction very often results in more regulations and restrictions which frequently fail to address the real problems.

Jan 1, 1990

By David E. Siskind

Increased mineral consumption and environmental concern have caused much interest in potential damage and annoyance from ground vibration and airblast produced by production blasting in surface mines and quarries. Ground vibrations are traditionally blamed for "shaking the house to its foundations," but often the airblast is responsible, particularly when the distances from mine to structure are large. Simultaneous measurements of ground vibrations, structure vibrations, and indoor and outdoor noise from blasting are being used by the Bureau of Mines to determine the relative importance of the ground and airborne blast energy in shaking the structure and making windows, dishes, etc., rattle.

Jan 1, 1977

By Yeon-Ho Jin, Eui-Haeng Heo, Yun-Seok Park, Sung-Oong Choi, Hyung-Dong Min, Min-Su Jeong, Seung-Joong Lee

As rock fragmentation in bench blasting can affect the following process such as loading, hauling and crushing, its good control is essential for assessment of blasting efficiency and production cost.

Jan 1, 2015

By M. Oguz Ozkazanc, Gulsev Uyar Aldas

Because of its safety, being easy to handle, relatively inexpensive and containing a lot of energy, ANFO is the most popular and widely used explosive in Turkey as well as other countries in the world. According to change dated May 14th 1999 on the regulation 87/12028 related with explosives, blasters are not allowed to mix ammonium nitrate and fuel oil in the tield to make ANFO. Instead of this, they have been forced to use the ready ANFO prepared by explosive producer firms. As a result of this obligation, the use of technical nitrate for agricultural purpose and mixing AN and fuel oil in unsuitable conditions have been prevented. Indeed, wrong mixture means waste of energy and money.

Jan 1, 2001

By Kenneth Eltschlager

The Surface Mining Control and Reclamation Act of 1977 requires that blasting be conducted so as to prevent injury to people and damage to public or private property. The three adverse effects are flyrock, ground vibrations and airblast. Blasting close to people frequently results in complaints of annoyance or damage. Federal and State personnel are responsible for evaluating the validity of the complaint. The elements to be evaluated include: reviewing blast logs, inspecting the mine, inspecting the house, measuring ground, air and structure vibrations, and predicting vibration levels. Computer spreadsheets, with their graphical capabilities, will be used to show how data can be cross tabulated to verify data accuracy. Complete statistical analyses of vibrations require more powerful software to make vibration predictions. Once all available data are gathered and verified, a decision on the complaint can be made.

Jan 1, 2001

By Egonk Arriagada, Jair Alarcon

The efficient use of energy in the ore comminution process is an increasingly important strategic issue for improving the productivity and competitiveness in the mining industry as is in recent years the related focus on reducing energy intensity on the atmospheric pollution and greenhouse gas emissions from its use.

Jan 1, 2015

By Tapan Goswami

A column of stemming material keeps explosion gases at high pressure for longer times in a blasthole. In general, use of appropriate stemming enables the achievement of the desired level of fragmentation and looseness of muckpiles, as well as the reduction of airblast and fly rock. The ejection resistance of a stemming column varies with the type of stemming material employed. In an effort to optimise stemming at Mt Owen Mine in the Hunter Valley, Australia, a trial was conducted to assess the efficiency of two types of stemming materials. Mt Owen mine relies on through seam blasting and stemming quality is important in this challenging blasting environment. Each type of stemming was trialed in different section of a blast. The blast was designed using Orica’s SurveyPlus@, LoadPlus@ and ShotPlus@ software. Measurement was done using high speed filming of the blast and then post blast information was obtained from analysis of the film. Data analysis included determination of the ejection velocities and percentage swell. Digging rates were measured from excavator production rates. Despite the presence of rounded surfaces and finer particle sizes, River Pebble stemming material showed superior ejection resistance. It also appeared to perform as well as more angular and expensive Crushed Stone, a finished quarry product, based on excavator productivity and heave. It was recommended that future blasts at the mine be stemmed with the River Pebble stemming material.

Jan 1, 2000

By Ian Bell, Shahram Tafazoli, Bahram Sameti, Aylin Azmin, Edmond Chow, Nima Ziraknejad

Image-based rock fragmentation analysis methods have been applied by blast engineers to estimate rock size distribution for over 25 years. These methods utilize a wide range of image segmentation techniques, from manual to fully-automated, to delineate the edges of the rocks in the image. In most commercially available image-based rock fragmentation analysis systems, rock delineation results are converted to physical rock sizes by introducing one or more reference objects (e.g., basketballs or other objects with known geometry) to the scene as size-scaling references.

Jan 1, 2014

By David Hersey

The Paseo Bridge was located at the I-29/I-35/US-71 Missouri River Highway Crossing. It was built between 1952 and 1954 by Massman Construction Company. The 1,232 foot long, self-anchored suspension bridge was the longest of its type when built. On Jan. 22, 2003, a connector pin designed to allow the bridge to expand and contract during temperature cycles seized and caused a portion of the bridge deck to raise up and block traffic. This marked the beginning of the end for the old Paseo Bridge.

Jan 1, 2013

By L. A. Heim, E. A. McCullough, N. J. Amiotte

The explosives industry is subject to the laws of multiple jurisdictions, which means that several regulatory agencies are responsible for governing different aspects of the commercial explosives industry. Among these regulators are the Mine Safety and Health Administration (MSHA) who implements codes that better ensure both occupational and public safety which is influenced by professional blasting projects and the Bureau of Alcohol, Tobacco, Firearms and Explosives (ATF), who enforces commercial explosives storage and security, among other responsibilities.

Jan 1, 2014

By Thomas L. Barkley

My historic auditing of Underground Drilling and Blasting Practices has demonstrated to the author the need for reviews of many mines' procedures in these processes. Poor understanding of the basic principles and practices of the drilling and blasting science in Underground Development Mining has created significant costs to mining operations in many instances.

Jan 1, 2019

By Steve Collinsworth

Sometimes, for those of us in the right place at the right time with the right product, necessity creates opportunity. Such is my case at a West Virginia coal mine where a mine manager was desperately seeking a way to eliminate coal damage on cast shots while maintaining cast percentage without the expensive process of secondary drilling. This paper will focus on how bottom hole air decking is solving the problem.

Jan 1, 2000

By R. F. Favreau, Favreau Patrice

"The economy profits from the rock excavated in mines and quarries and the excavations required for the construction of roads and buildings. However such excavations are achieved by blasting withexplosives, and explosions create fly rock and vibrations which in some cases may throw rock far intoinhabited regions and may vibrate buildings excessively in these regions. Society, however, no longeraccepts that their quality of life be disturbed by the risks of fly rock or the perturbation of vibrations.Thus it is important to know how to design blasts that do not cause excessive fly rock or vibrations, and to understand why sometimes a blast does create excessive vibration or fly rock. An article presented at the 2015 ISEE (reference 1) explains how unacceptable vibrations can be avoided, while the present article explains why dangerous fly rock occurs and how it can be avoided. The article shows by rigorous calculations with the blast simulator Blaspa that long range fly rock can be due to short collar or short burden, but mainly it explains how inadequate blasting that allows the floor to rise can cause even further reaching fly rock, a situation not usually recognized by most blasters."

Jan 1, 2016

By Stephen Chung

The quality of a blast design can be evaluated in many ways. It may involve fragmentation, muck profile, environmental effects in terms of vibration and the excavation of the blasted material. To assist and ensure an achievable cost effective design, numerical modeling techniques are often applied as part of the operating procedure. While excavation is one of the mining operations which has a direct influence on the bottom line cost of productivity, the characteristics of a pile of blasted material deserves a closer look in terms of diggability. This paper reviews the current diggability techniques available for application to the blasting operation. To help better understand the involvement in digging, this paper also introduces an evaluation approach based on a discrete element method. The model presented in this paper deals with many variables that are considered to directly affect digging. They are the density and cohesion of material, fragment shape and size distribution as well as the swell of a muck pile. To help visualize the analysis approach, sample runs and animations are given in the paper to show the setup of muck piles produced in bench blasting as well as in sub-level caving. The computed forces experienced by the bucket during each mucking cycle are also discussed.

Jan 1, 2008

By Jorge Alvarez

In a large-scale open-pit mining operation, continuous efforts are made to control damage to the slope walls. An essential tool in this effort is determining the PPVc (critical peak particle velocity) in areas of interest. By knowing this value and generating criteria, drilling and blasting designs can be established to reduce vibrations that affect wall construction. It is crucial to understand that the PPVc changes as different mining phases develop, especially due to exploitation on the benches, which leads to vertical inherited damage. Therefore, it is imperative to regularly update the PPVc based on field tests that provide accurate data. With this information, vibration damage criteria can be established, and drilling and blasting techniques can be designed to minimize the impact on the remaining rock mass. This document presents a methodology for generating scaled criteria that best represent the reality of the rock mass.

Jan 21, 2025