Search Documents

By William Gates, Gabe McClain, Thomas Pallua, Joe Schrank

The Tennessee Capitol Corridor connects the Cordell Hull Building (CHB) to the State Capitol, which isa 232-foot-by-124-foot (71 x 38 m) structure in Nashville that includes porticoes built from local massive limestone. This connection was affected by the Capitol Connector Pedestrian Tunnel (CCPT) project, which is part of the overall Cordell Hull State Office Building and Central Services Demolition, New Construction and Renovation Project (Cordell Hull Renovation Project). To construct this connection, the two existing elevator shafts and a new emergency stairwell in the State Capitol were extended down to anew lobby area—the elevators by about 50 feet (15.2 m) and the stairwell by about 60 feet (18.3 m). This lobby was connected to the CHB by a 435-foot-long (133 m) pedestrian tunnel. It was predicted that most of the tunnel would be excavated in a relatively strong limestone; therefore, considering the project features and constraints, drill-and-blast techniques were selected as the primary excavation method. Because of restrictions on blasting in urban areas and, more importantly, the proximity of this construction to national historic landmarks, blasting operations were extensively monitored to measure and correlate ground vibrations as peak particle velocity (PPV), frequency, and strain—these being the major factors that would impact the surrounding buildings. As a result, copious amounts of data were gathered and interpreted within a short time to estimate blasting parameters and optimize the subsequent blast rounds. To calculate the ground response factor, the scaled distance of each shot was compared to the ground vibration as PPV, generating a subsequent regression curve with an R2value of about 0.7. Using the best fit curve equation, the estimated ground response factor was about 150 for the best fit line. Other than some cases with relatively high (> 2 in./sec [51 mm/sec]) recorded PPV values, the blasting operation was successfully conducted as planned and the observed strain on the monitored buildings was very low, mainly within ±2 με (0.0002% elongation). (In general, the recorded PPV was lower than 2 in./sec at frequencies of more than 50 Hz.). The strain gauges at key locations (cold joints and old fractures) in the Capitol and on other critical structures demonstrated strain was insignificant in relationship to ground vibrations from the blasting operations. The apparently small vibration-induced strains were related to the massive limestone construction of the Capitol and ancillary buildings, as the induced strain plus the existing strain did not exceed the critical strain of the massive structures.

By Stewart A. Silling, D. Lynn Gordon, C. Mick Lownds, Dale S. Preece, Ali Bhuiyan, Patrick R. Bowden

Blast heave modeling and prediction utilizing the new discrete element model, GEM, that treats rock as elements with alternating arcs and line. Explosive loading of GEM elements is accomplished by utilizing the Noble-Abel equation of state to track the gas pressure from detonation through expansion to atmospheric pressure.

Feb 1, 2020

By Alan Hooper, James E. Mischler

Construction began in 1984 for a 5 megawatt hydroelectric power retrofit at the O'Shaughnessy Dam for the City of Columbus, Ohio. The construction necessitated excavation of limestone bedrock up to 27 feet below the normal water level of the river downstream of the dam. Proximity to the river and difficult terrain resulted in an interesting and challenging construction project.

Jan 1, 1986

By Ian Bell, Saman Nouranian, Shahram Tafazoli, Bahram Sameti, Mahdi Ramezani

"Image-based rock fragmentation sensing in mining and quarry applications includes an important rock boundary delineation step, which is commonly referred to as rock segmentation. This paper presents a novel approach to solve this problem, using artificial intelligence. In the proposed technique, priorknowledge of previously analyzed images is encoded into mathematical/statistical models. A set of human labeled images are used as training inputs. These images are used to train neural networksthrough an optimization process. The networks can then be used in real time for rock delineation. "

Jan 1, 2017

By Matthew Clay, Colin Chambers, Susan Hookham

Opencast (quarries) and underground mines around the world use blasting methods to mine valuable ore. Traditional blasting systems use technologies such as electric delay detonator systems (developed in the 1950s) and non-electric detonator systems (developed in the 1970s) to initiate a detonation train to blast rock more effectively, and so retrieve valuable product more efficiently. However, the lack of precise control over blast timings with these approaches can result in undesirable outcomes such as significant flyrock, excessive ground vibration, uneven grade of rock and misfires (in which sections of the blast can remain unfired). The development of Electronic Initiation Systems (EIS), first used in the 1990s, introduced a higher level of control over the blast. These systems greatly reduce the negative issues associated with blasting. However, this precision introduces complexity, and with this complexity comes difficulty in demonstrating the predictability, safety and reliability of such systems.

Jan 1, 2017

By Michael Laing

Blasting regulation and restrictions are tougher today than ever before. When blasting in population centers, strict limitations are often placed on the environmental effects caused by blasting, more specifically vibration and overpressure. Blast-induced vibration can be a tricky thing to manage at times, but there are a variety of options at our disposal to help optimize and manage vibration. This paper focuses on the application of rudimentary signature hole analysis to optimize blasting vibration in localized areas surrounding a mine.

Jan 1, 2017

By Gabe McClain, Thomas Pallua, Joe Schrank, William C. Gates

Because of restrictions on blasting in urban areas and, more importantly, the proximity of this construction to national historic landmarks, blasting operations were extensively monitored to measure and correlate ground vibrations as peak particle velocity (PPV), frequency, and strain—these being the major factors that would impact the surrounding buildings. As a result, copious amounts of data were gathered and interpreted within a short time to estimate blasting parameters and optimize the subsequent blast rounds

Feb 1, 2020

By Matias Suarez, Diego Zenteno

It is known that the introduction of electronic timing in the sequencing of blasting has changed the vision and way in which mining is developed. It is possible to deal with more complex and sophisticated drilling designs, without compromising productivity or safety. It has been shown in various studies, that a correct timing of the blasting provides an improvement in the improvement of the processes downstream, due to a decrease in the resistance of the resulting fragments coming from the interaction of the waves generated in the detonation of explosive loads. On the other hand, it has also been shown that variations in the composition of a same type of explosive, has a significant influence over the resistance of the blasted material, also the energy associated to break it, affecting directly its degree of fragmentation. This paper is aimed to display the new advancements of blasting engineering done in different mining sites throughout the country, associated to electronic sequencing, energy of the explosive and its impact on the fragmented rock. This document explains how to define and implement selective sequencing in the blasting in order to promote the propagation of cracks, therefore impacting positively the productivity through the use of the LaGrange diagram. The LaGrange diagram is a very convenient and illustrative method to present the dynamic behavior associated with wave and crack propagation (Rossmanith. H, 2002). This study focused on the methodology of the formation and measurement of seismic pulses, through the rock massif. For this purpose, seismic pulses were acquired in the field and then, the different dynamic phases of the wave were molded mathematically, with the purpose of favoring the coupling between them.

By Darío Innamorati, Jorge Oliva

Cerro Vanguardia is a known gold and silver deposit located in the province of Santa Cruz, Argentina. The mine has been in operation since 1998 and is thought to be one of the most important mines in Patagonia. More than 102 epithermal quartz veins have been identified in the area, with variable lengths, thicknesses, orientations and dips that constitute what is possibly one of the most extensive outcropping vein systems on earth. Veins are vertical and have variable depth. For this reason, the deposit is currently mined with a variety of extraction methods. This operation is made up of more than 60 open pits and 20 underground access ramps to exploit the deepest high grade narrow veins. This study is focused on the combination of underground exploitation with open pit blasting. That is, those production stopes in the upper levels of underground mines and their interaction with the damage levels in the final slope of open pit mines, as well as in the study of the impact of the generation of vibrations from the blasting of open pit mines and their influence on underground mines. Considering the current stage of the mine, after 20 years of operation, Cerro Vanguardia faces the need to mine deeper deposits in the face of increasing costs and declining grades. For this reason, it is essential to study the interaction of these exploitations. From a personnel safety point of view, this interaction must be well coordinated so as not to affect people and equipment. Likewise, the generation of vibrations due to blasting must be studied, which would produce new cracks, potentially generating overbreak and dilution. The main objective of this study is to determine the possible causes and influences of the blasting interaction in open pit and underground mines, seeking an optimization of the blasting process and a safety standard for personnel and equipment. To achieve these goals, this study includes a vibration monitoring plan to analyze the charge performance and determine rock constants. With the use of specialized software, damage modelling and simulations are used to determine values of damage in order to reduce overbreak. In addition, this plan contemplates the estimation of flyrock in blasting where underground work is connected to the surface, determining safety distances when carrying out a blast.

Jan 21, 2025

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan

In the bench blasting, the realisation of an economic, and safe blasting is only possible with a reliable blasting design on condition that considering all sequential activities such as drillingblasting, excavation-loading, haulage, crushing (especially primer crushing). Here what we mean with a good, and reliable design is that ensures an almost displaced, adequately swelled muckpile with desired fragmentation degree for the loaders effectivity, and succesive usage. Meanwhile it must also has no environmental problems such as ground vibration, air blast, and rock flyings, or at least these matters have to be minimised. Two main parameters which have generally being questioned to achieve a safe and economic design on any rock conditions, are specific charge, and burden. In the condition of determining these elements, the other blasting parameters could be calculated according to them, and the blasting design could be completed. Within the scope of this study, it was aimed to determine the optimal blasting conditions of gypsum which is major rock unit of overburden at Sivas Celestine open pit mine. First of all, the engineering (mass, and material) and digging difficulty classifications of gypsum were done according to the current classification systems by using the results of field and laboratory studies. Then the blasting system which was being used on all rock units, was considered, and the necessary data were obtained. After previewing the site properties, predesigns were done, and applied by adopting Langefors design model. The necessary adjustments were done before, during, and after the shots, and the applications were observed. In order to determine, and record the data from each shots properly, a practical form was developed, and all data were transfered to these forms which give information about the blasting results such as muckpile displacement, and height, average particle size, back break, and rock fly existence, number of boulders etc. The blasting parameters such as burden, hole diameter, hole inclination, the amount and position of primers, bench height, delay sequence, and blasting geometry were considered for the iteration of each shots. During the applications, ANFO, gelatine dynamite, and electric delay detonators were used as explosives.

Jan 1, 2004

By Felipe França Sitonio

Parameter’s control of explosives used in blasting operations have become more relevant over the years, bringing a better understanding of detonation performance. Giving into consideration that bulk emulsion density’s variation reflects directly on blasting results due to its importance in product sensitivity and velocity of detonation (VOD), blast designs are conducted assuming that cup density measurements are reliable and explosives gassing agents will perform as per specifications. Nevertheless, confinement conditions in boreholes like temperature, presence of water and surrounding circumstances of rock mass are often neglected on predictive modelling and off-site measurements. This paper describes the assembly of a device equipped with pressure sensors and its utilization in confined boreholes of an open pit mining operation, aiming to obtain in situ monitoring of density variation in several explosive columns. After we developed a software to get and process data of a hardware prototype and the device functionality was validated in water, oil and quarry mining experimental trials, 7 of 291 boreholes in a gold mine operation were chosen to be monitored with two probes each, placed at the top and at the bottom of the explosive column profile. The results obtained enabled a comparison between the bulk emulsion density variation when acting in different environments, since we selected boreholes with diameter of 101.6 mm (4 in) and 139.7 mm (5.5 in) and some with presence of water. Besides the increase of explosive density with depth related to hydrostatic pressure increase, we found an overall error of 6% in cup density measurements when compared with sensors placed at the bottom of boreholes and 2% when compared with sensors placed at the top of explosive column. These findings provide detailed insights into how bulk emulsion explosives behave in different circumstances including depth and borehole diameter, giving the opportunity to re-evaluate blast design parameters such as its geometry, sequence pattern, charging profile and explosive composition.

Feb 2, 2020

By Cristian Rodriquez, Fernando Fernandez, Rodrigo Fuentealba, Tom BoBo, Maria Rocha, John Kemeny

This paper describes a case study that was conducted at a new mine in South America. This mine has significant geologic variations that will result in different distributions of hard and soft ore being mined at different periods of time over the mine life. A study was conducted to determine the optimum blast design that will meet the mill throughput requirement of 95,000 tonnes (104,720 tons) per day for the first 10 years of the mine life. As part of this study, field rock mass characterization and laboratory tests were conducted. This includes standard rock mechanics tests as well as rock breakage tests used in mill simulations. The geology of the ore body was broken up into four Geologic Units, and statistical variations in the properties were determined for each unit. Using this data along with the data on the occurrence of the different geologic units over time, simulations were made of the run-of-mine (ROM) fragmentation due to different blast designs, and these results were used in simulating the resulting throughput after crushing and grinding. Four blast designs were considered with powder factors of 0.44, 0.54, 0.64 and 0.94 kg/t. The results of this study show that determining the proper blast design is important in ensuring that the mill throughput requirement will be met over the mine life.

Jan 1, 2015

By Manuel Gutierrez, Roberto Gomez, Juan Aravena, Johan Gjoevad

The use of explosives in mining operations is a process that involves the search for an ideal explosive for the type of geological condition of the mineral to be extracted. For the explosives present on the market the majority are based on Ammonium Nitrate. This as it is an ideal balance of high energy efficiency achieved with low development of gas emission. The manufacturing and loading operation of the explosive requires multiple process stages and different raw materials, which, if is not correctly supervised and controlled may cause the development of harmful gases or, in the worst case, even toxic gases. The majority of mining operations are located at remote locations without the presence of communities, and hence individuals, which could be affected by emission of the harmful or even toxic gases. In these operations the protection is mainly to protect the employees of the operation. However, if the operation is located near communities, the effect of these gases becomes a serious problem. The communities' perception of post-blasting gases, according to interviews carried out in this project, describes these as smells of black gunpowder, damp soil with a volatile permanence and medium intensity, sometimes a stinking tone is added. The legislation in Chile that controls the exposure of “workers” to different gases is Supreme Decree 594, 2019 (Decreto Supremo 594). Currently the Chilean Ministry of Environment and Sernageomin (Servicio Nacional de Geología y Minería) are taking actions to reform and strengthen oversight, seeking through a short law to provide more tools to the government to decentralize decisions in case of non-compliance with the decree. This paper describes the development and implementation of a permanent and remote gas monitoring system, considering the reasons for choosing the gases to be included in the equipment, the types of sensors and their capabilities, the way to verify in the field the correct functioning of the technology throughout the project, and finally how the data collected in the field is meeting the government's expectations in terms of permanent and online reportability. Additionally, it addresses the continuity of gas monitoring in the community that will disappear in the short term due to the expansion of mining operations, thereby ensuring the protection of both workers and affected communities.

Jan 21, 2025

By Adrian Moore, Alan Richards

"It has been common practice to set blast vibration limits for structures using an “observational”approach whereby limits are set at a level based on observations of damage, or the lack ofdamage, combined with a tendency to further reduce the permitted level due to uncertainty. Suchan observational approach was used in the USBM RI 8507 to produce the frequency dependent‘Safe Levels of Blasting Vibration for Houses’ which has become a universal Standard for overthirty years."

Jan 1, 2013

By Kristen R. Bingham

"Today, more than ever, drilling and blasting contractors are challenged to manage the ever-changing risks associated with blasting operations. New neighborhoods are encroaching upon mine sites and blasting projects are confronted with increasing scrutiny by permit issuing authorities and nearby residents disgruntled by new construction. The act of transporting explosives material to and from thejobsite is far from easy and trouble-free. At the same time, the pressure to stay in compliance with the growing number of government regulations continues to mount. While new tools and technology are appearing in the workplace to address some of these challenges, losses still occur. Can the datagenerated by this technology help drilling and blasting contractors make better decisions? While basic risk management principles are still applicable, do new tools and technology assist in the effort to prevent losses? What are the downsides? In this age of new technology, is face-to-face interaction still necessary? While technology is certainly a useful component in the drilling and blasting world, can it be helpful in defending claims?"

Jan 1, 2017

By Braden Lusk

The problem of predicting damage in densely developed areas due to incidental or malicious explosions is one of considerable importance to local, state, and federal governmental bodies. The difficulty of making such a prediction is confounded by the urban canyon phenomenon as the shock wave intensifies or rarefies depending upon the particular arrangement of buildings. The specific method detailed herein used a Computational Fluid Dynamics solver, ANSYS AUTODYN, to operate on Geographic Information Systems data, ArcGIS, which captured the geospatial relationship between the various buildings in downtown Oklahoma City, prior to the Murrah Building bombing. The model of Oklahoma City was first developed using the building footprints and elevations provided by the ArcGIS database. Due to the sheer size of the problem, the model was then subdivided into annular zones of increasing distance from the center of the blast. Each subsection was then solved using an Euler model in a cascading fashion with the output of the preceding model forming the input of the present model. To further reduce computational time, the size of the Euler nodes was increased at each stage as the section area increased. Due to the loss of precision in capturing peak pressure values when using larger size nodes, it was necessary to perform a transformation on the results using one dimensional wedge calculations with higher precision. The Murrah Building bombing event was an excellent case study due to its available ArcGIS data and the level of documentation of damage to surrounding structures due to the blast. The results from the staged CFD calculation were then used to develop a damage potential contour map. The documented incidents of damage in the area surrounding the Murrah building were then compared to the model generated damage potential contour map. Copyright ©

Jan 1, 2010

By Thomas E. Ricketts

Occidental Oil Shale, Inc. constructed two commercial-sized modified in situ (MIS) retorts, Retorts 7 and 8, at its Logan Wash Oil Shale Mine in February and April 1981, respectively. One of the primary objectives of this two-retort program was to examine large-scale blasting reproducibility for commercial-sized retorts. The blast design used 545 blastholes and 550,000 pounds of explosive in ANFO equivalent per retort. Each retort was blasted using millisecond delay blasting caps tied into a single round. The blasts resulted in rubble beds very close to one another and to predicted results obtained using newly developed limited void blasting technology. The heights of the remaining void rooms over the beds after blasting were within 0.3 feet of one another. This excellent reproducibility is brought into true perspective when compared to the scale of the rubble beds which were 230 feet high with volumes of over six million cubic feet each.

Jan 1, 1984

By Randall Wheeler

In early 2008 we were asked by a quarry to become involved in a conflict with a pipeline company concerning blasting near one of their underground high pressure gas lines. The pipeline company, without the quarry’s knowledge, had sought and obtained a temporary restraining order against the quarry forbidding them from blasting near the pipeline.

Jan 1, 2011

By Orica Peru, Pedro Lozada

Proper management of exclusion zones in blasting operations is essential to ensure safety without compromising operational efficiency. In Peru, mining regulations establish minimum exclusion distances specifically for personnel (500-meter radius / 1,640 feet), but do not define clear technical criteria for equipment. As a result, conservative distances such as 200 meters (656 feet) are often applied, negatively impacting productivity. This study proposes a technical-scientific methodology to reduce equipment exclusion zones, based on the use of advanced technologies such as drones, high-resolution cameras, and specialized software tools. The solutions used allow video recordings of blasts to be transformed into dynamic data through artificial intelligence and computer vision, as well as execute probabilistic simulations of the flyrock phenomenon using Monte Carlo algorithms and physical models calibrated to real operating conditions. Technological integration enabled the simulation of real operational scenarios, considering variations in critical blasting parameters that directly affect flyrock generation, such as drill diameter, explosive density, linear charge, and stemming height. Additionally, the Terrock methodology was incorporated, allowing the behavior of the rock mass to be included as a variable in risk assessment, improving analysis accuracy under different rock hardness conditions. The methodology was applied in four phases: diagnosis of the current design (15 blasts), modeling, validation of the calibrated model (6 blasts), and subsequent operational implementation. As a result, it was determined that the exclusion radius can be safely reduced from 656 to 492 feet (200 to 150 meters), maintaining as the main restriction the use of stemming lengths greater than 5.0 m. This optimization has the potential to generate tangible benefits, with estimated monthly savings exceeding USD 50,000, associated with reduced evacuation times, lower fuel consumption, less equipment wear, and increased productivity in drilling and hauling activities. The comprehensive approach presented here highlights the transformative potential of digital technologies applied to blast management, contributing to safer and more efficient mining operations.

Jan 26, 2026

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson, Brian Somes

"To perform a probabilistic risk assessment (PRA), a method of quantifying the risks associated withinfrequent, high consequence events, consequence models that generate representative estimates of human health consequences for a wide variety of representative scenarios are commonly used. Criteria that suitable models must possess include: (1) input requirements necessary to generate large volumes ofprobabilistic simulations; (2) the capability to output injuries with the necessary details and resolution;(3) the ability to capture the variety of different scenarios inherent in an assessment; (4) acceptablecomputational requirements; and (5) sufficient stakeholder buy-in for community acceptance."

Jan 1, 2017