Search Documents

By Richard H. Granhom

Detonation pressure, or Chapman-Jouguet pressure, is an intrinsic property of an explosive, and like detonation velocity, is an indicator of explosive performance. Pressure and velocity are also important for calibrating computer codes and for other calculations such as the stress imparted to rock or metal by an explosive. The detonation pressures, P~cj, of many "ideal" explosives have been measured indirectly by recording some hydrodynamic flow variable other than pressure, with P~cj being inferred from hydrodynamics and the assumed Chapman-Jouguet equations. One such method is the difficult and expensive "aquarium technique''.] Commercial explosive manufacturers generally rely on estimates of P~cj generated by computer codes not explicitly designed for non-ideal explosives typically used in commercial applications. Over the last decade, U.S. national and government laboratories have developed in-situ gauge techniques such as the manganin gauge, for direct measurement of detonation pressure. Manganin is an alloy of copper, manganese and nickel, and is ideally suited for use as a pressure transducer because its electrical resistance changes with pressure, but is nearly constant with changes in temperature. A simplified manganin gauge technique adapted for use at a commercial test site is described and some initial results from measurements on commercial emulsion explosives are presented.

Jan 1, 1991

By E. Contestabile, B von Roser

Schedule IV containers in Canada and IME- containers in the United States have made possible the transport of mixed loads. That is, using these containers for detonators, one can simultaneously transport detonators and explosives on the same vehicle. As a result of a recent accident, the Canadian Chief Inspector of Explosives asked for a review of the appropriateness of the Schedule IV container in its present use. The Canadian Authority asked for a re-assessment of the adequacy of the Schedule IV container in preventing propagation of a reaction from the detonators in the container to the remainder of the explosives on the truck, and its ability to contain fragments generated by the detonators. A series of tests was performed to determine the initiation threshold temperature for non-electric detonators and the failure threshold temperature for the shock tube to establish some guidelines for preventing communication from one case of detonators to another within the transport container at elevated temperature. Tests fell into the following categories: inter-case sympathetic detonation, detonator thermal auto-initiation, shock tube thermal sensitivity, and intra-case sympathetic detonation. The results indicate that temperature is a critical factor, which determines to what extent, if any, communication occurs.

Jan 1, 2002

By D Wilson, R R. Vandebeek, R A. Bowes

"As business opportunities are sought around the world, the explosives industry must oftengrapple with the United Nations Transport of Dangerous Goods Recommendations.Canadians have problems in this area that are similar to those of other countries. Thispresentation outlines, through a case study, how a container for shipping ""explosives"" wasdesigned, tested and approved for use by the Chief Inspector of Explosives, the""Competent Authority"" for Canada."

Jan 1, 1993

By Kamal Wadhwa

Liquid oxygen explosives have been used in India for well over 5 decades now. These are being extensively used both for shallow and deep hole blasting in the various opencast mines and quarries for mining of coal, limestone, ironore, bauxite, magnesite etc. IOL Ltd., are the pioneers in the introduction of these explosives in India and are marketing these under the brand name 'LOXITE'.

Jan 1, 1991

By Guillermo Silva

A novel, ultra-low density explosive composition, particularly suited for wall control and other applications requiring customising of the explosive’s energy output, has been developed. Being reactive in nature, the low density explosive enables the controlled dilution of dry blasting agents from their nominal densities down to values slightly less than 0.10 g/cm3. The product has been detonated at densities of 0.07 g/cm3 in diameters as small as 50mm under confined conditions, using a 227 g (l/2 lb.) primer. Recorded velocities of detonation ranged between 1200 m/set and 2200 m/set for densities between 0.07 and 0.2 g/cm3. Theoretical velocities ranged from 1700 m/s to 2500 m/s for the same density range. The low density explosive was insensitive to initiation by a blasting cap which is a desirable feature for transportation purposes. Mixing of the product with ANFO has been accomplished with minimum segregation making it suitable for applications where reduction of pressures are necessary.

Jan 1, 2000

By Lyle Avey

For the purpose of this paper, testwork and general pre-splitting practice will be discussed for the Chimney Creek Mine.

Jan 1, 1990

By William. J. Birch, Catherine. E. Johnson, Robert Farnfield

Rocks and other materials can be characterized by their elastic properties. However, seismic velocities represent a more practical set of physical properties for seismic methods. Seismic velocities define the speed at which various elastic deformations propagate through different rock types. Seismic velocities for a given material can be expressed explicitly in terms of their elastic properties. It is widely accepted that the peak particle velocity and associated frequency of ground motion are important parameters for determining a safety criterion to minimise the potential for both damage to structures as well as nuisance to people. Whilst the key considerations are the blast design parameters, the seismic velocity is important as particle velocity is dependent in part on the powder factor [blasting ratio] which in turn is found to be dependent on the seismic velocity.

Feb 6, 2023

By D Schneider, H Elliott

The advantages and disadvantages of using inclined boreholes in blasting has been under discussion for a long time. Some recognized disadvantages are that drilling costs, both operating and capital costs, are higher for inclined holes than for vertical ones, and that drilling accuracy is more difficult to maintain. People who have used angled holes in practice, on the other hand, have claimed that the quality of blast results was improved. In fact, their popularity has increased, especially in Australia.

Jan 1, 1988

By Conny Sjoberg, Finn Ouchterlony, Bjorn Jonsson

This contribution reports an investigation of the blasting damage in the contour of an access ramp to a Swedish underground laboratory for nuclear waste related studies. Near zone vibration measurements were made for 7 rounds and the results converted to a site specific scaling law. A simple engineering correction for the influence of the charge length wee developed and the resulting equations used to predict the damage zone depths of three different drilling and charging patterns.

Jan 1, 1993

By Nolan Eckroade

The demand for blast optimization within the quarrying industry calls for more effective, faster and safer methods of quantification of blast performance. Drones provide the ability to safely and quickly capture high resolution imagery of a muckpile for use in fragmentation photo analysis. Oversize material within a muckpile is an expensive and universal problem affecting quarries, especially in situations where cap rock is present. Although the amount of oversize material in a blast is a key indicator of blast performance, it is difficult, hazardous and slow to measure across an entire muckpile using traditional methods. By piloting a drone using an automated flight plan with set amount of overlap across images, the images can be processed into a single, high resolution orthomosaic image for use in fragmentation photo analysis software.

Jan 1, 2018

By Z X. Zhang

In sublevel caving mines, eyebrow break usually gives rise to lower ore recovery and worse safety in the field. Eyebrow break is caused mainly by two tensile stress waves: one from the front surface of a blasting ring, and the other from the roof of the drift. In order to reduce the two waves and finally to reduce eyebrow break at Malmberget mine, we employed two methods: (1) cartridge charge, and (2) double-primers in each blasthole. The two methods were tested in one ore body called ViRi. A total of 10 rings with the cartridge charge and 25 rings with the double-primers were blasted. At the same time a total of 34 ordinary rings were blasted in the same ore body. The result shows that the eyebrow break is 3.0 m for the ordinary rings, 2.3 m for the cartridge charge rings, and 2.1 m for the double-primer rings, respectively. In addition, the ore recovery for the double-primer rings is increased by 3% on the level of ViRi930, compared with that for the ordinary rings.

Jan 1, 2011

By Richard J. Mainiero, Michael S. Wieland, Harry C. Verakis

The Bureau of Mines, U.S. Department of the Interior, has been conducting research on delay blasting in underground coal mines in support of the efforts of Mine Safety and Health Administration (MSHA), U.S. Department of Labor, to revise coal mine blasting regulations. Part of the research centered on developing an understanding of the factors that lead to misfires of permissible explosives. Research was conducted to determine whether frequency of misfires was related to borehole spacing. For a wide variety of permissible explosives, misfires were observed for about 50 X of the holes at 45-cm (18-in) spacing. Misfires were also observed for 60-cm (24-in) spacing, but the frequency of misfires was much lower than observed for the 45-cm (18-in) spacing. The Bureau has recommended that hole spacings of less than 60 cm (24 in) be prohibited.

Jan 1, 1986

By Harry Verakis, Thomas Lobb

This paper is a summary and an update of the underground mine blasting accident investigations and studies previously conducted by the Mine Safety and Health Administration (MSHA) and the former US. Bureau of Mines. Blasting accidents are usually a small percentage of the total number of mining accidents. However, blasting accidents continue to occur and the severity of these accidents is disproportionately high with respect to other types of mining accidents. In 2000, about 5.7 billion pounds of explosives were produced in the USA. The mining industry consumed the greatest portion of explosives manufactured for blasting with about 67 percent used for coal mining. Metal and nonmetal mining operations account for about 23 percent of the use of explosives. The use of permissible explosives in underground coal mines continues to decline (3,373,069 pounds for 2000).

Jan 1, 2002

By Paul Worsey, Gerald Rupert, Mark Kirkbride

The realignment of Highway H in the proximity of Crystal Cave (Springfield MO.) required the development of a blasting program that was both economical and efficient for construction, yet ecologically safe for the cave. Three component seismographs were strategically placed underground near prominent and sensitive cave features and the vibration levels from the construction blasting continuously monitored. Peak particle velocity (PPV) values were found to obey the square root scaling law and a peak particle velocity value of 0.3 in/sec was chosen as the safe maximum limit. This value proved adequate in preserving the integrity of the cave and its features. Scaled distances for the maximum and lower values enabled blasting personnel to select explosive charge weights per delay for given distance to the cave. Delays were determined from the dominant frequencies recorded underground.

Jan 1, 1997

By R A. Farnfield

Measurement of the environmental impact of ground vibration from blasting operations is based almost exclusively on the peak vibration level generated. This measurement is known as the Peak Particle Velocity or PPV. The recorded PPV is used to assess the impact of the vibration both in terms of structural damage and human response. Limits for vibration are almost universally quoted in terms of PPV levels and, as a consequence, blast design for vibration control is centred around techniques for the control of this peak value.

Jan 1, 1996

By Tim A. Beattie, John R. Grant, David L. Kennedy

After many years of research, ICI staff have developed a numerical modelling system for the study of detonator/primer/explosive configurations. Results from this work clearly identified that current primer designs were not as effective in delivering their energy potential as needed. Alternative designs were evaluated and several prototypes, all essentially spherical in shape, were built for testing. Results have shown a significant improvement in various aspects of primer performance, including omni-directional pressure transferral and increased energy release rates. Reliable, high performance priming of explosives is now achievable for a much wider application range.

Jan 1, 1991

This case history refers to the detonation of the two largest chemical explosions on the Australian continent. An important element of feasibility studies and construction guidance included prediction of fragmentation results and ground vibration effects for the detonation of two very large "coyote" blasts, consisting of mined tunnels filled with explosives. The larger of the two blasts contained nearly 1 1/4 million pounds of explosives detonated instantaneously. The explosives were placed in specially designed tunnels under a quartzite mountain for the purpose of generating rock fill for the main dam on the project.

Jan 1, 1995

By Jerry W. Schweiker

An extensive computer program has been developed which will store and analyze pertinent blast related parameters such as date, time, shot coordinates, charge, delay times, etc. In conjunction with these blast parameters, measured ground vibration information can be stored. In addition to actual seismograph data, predicted ground vibration in terms of velocity (inches/sec) can be generated for selected receiver locations. The magnitude of the blast generated ground vibration is based on scale distance relationships. The program can be used for planning blasts, to satisfy local environmental regulations and for insurance and/or legal purposes.

Jan 1, 1984

By Gungor Tuncer, Erhan Bakirci, Ali Kahriman, Atilla Ozmen, O. Nuri Ucan, Savas Gorgun

There are several methods for demolition of structures but most of them depend mostly on conventional ways of using machines for breaking and crushing structural elements. However the need for lots of work force, expense and extreme amount of time for demolition, made most of these methods non-popular nowadays. Therefore, trials to accomplish a more economic and less time taking method lasted with the use of blasting. By applying controlled blasting on a suitable structure, the structure can collapse and break down to pieces in very short period of time, with no extra work force and cost. In spite of advantages of explosive demolition, the potential danger of explosives and the damage that the blasting may cause to surrondings, if not controlled properly, made people timid to the method especially in urban areas. Therefore, the pre-assumption by computational analysis has become an essential matter in the process.

Jan 1, 2002

By Rolly Thorpe

Bulk emulsion explosives have been used at surface mines and quarries for many years. Recently, this technology has been adapted for underground use in relatively confined work areas and in smaller diameter blastholes.

Jan 1, 1994