Search Documents

By Gregory P. Lorsbach

Significant information about any blast is contained within the seismic signal generated by the blast. In this study, standard digital signal processing techniques are utilized to extract source parameter information from a seismic signal recorded at distances commonly used in compliance monitoring. Specifically, digital seismic data was analyzed using the cross-correladon and autocorrelation functions for the purpose of determining delay timing. The initial results are interpreted to indicate that: 1) Individual delays can be identified analytically but not visually for short delay periods and large source to receiver distances, 2) Delay timing can be resolved to a few milliseconds, and 3) Results can be obtained from data collected at a minimal number of locations.

Jan 1, 1991

By William H. Snyer, Hank Cox

A high explosive device using Linear Shaped Charge (LSC) (to rapidly cut vent and drain openings in a rail tank car) is described. In the event of damage to a tank car loaded with a pressurized flammable fluid, it may sometimes be necessary to perform controlled on-site vent, drain and burn operations. Existing techniques required refinement to achieve the desired safety and procedural reliability for use in emergency situations.

Jan 1, 1994

By Hubert den Dikken

ache, especially when it comes to forwarding of small quantities. Air transport is limited to 1.4 explosives on cargo aircraft and 1.4S classified explosives on passenger aircraft, so most samples cannot be transported by air. Ocean transport is a possibility, but due to stowage and segregation regulations of the IMDG code, a very expensive one. Road transport is often the only solution, but high explosives require special trucks with licensed drivers. The solution to these logistic problems is solved by creating a 1.4S (Class C) classification for all high explosives, when packed in special containment vessels.

Jan 1, 1995

By S Lukovic, Robert Briton, Calvin J. Konya

Investigators have reported that charges which are decoupled from the borehole wall produce different fragmentation then those which are fully coupled. The difference in effect could be as a result of energy doss during transmission across the air gap or it could be due to the change in detonation characteristics of the explosive as a result of the change in confinement on the charge during detonation. In order to better understand the phenomena of decoupling, a research project was conducted at the United States Bureau of Mines Station, near Pittsburgh, Pennsylvania. It was decided to use shock and bubble energy tests along with simultaneous velocity measurement to determine the mechanics of decoupling and energy transmission. Two explosives were selected for the test, one dynamite and one water gel. Test results indicated that decoupling could both boost the total energy output of the explosive and that further decoupling would drop the energy output.

Jan 1, 1987

By Pierre Mousset-Jones, Geraint W. Harris, Robert Karlin, Jaak Daemen

In order to minimize the ore dilution induced by blast movement in surface mines it is necessary to quantify such movement. This will make it possible to more accurately locate the grade boundaries on the surface of a blasted rockpile prior to excavation. This paper describes the development and testing of a method to accurately measure the direction and magnitude of sub-surface blast movement. The technique involves the use of magnetic "radiometry, using a cesium vapor "radiometer and real-time differentially corrected, GPS system, to locate the post-blast position of magnetically enhanced target objects, whose pre-blast locations are known, without disturbance of the blasted rock. The objective is to design an accurate and efficient technique which can be integrated into a mines production cycle.

Jan 1, 1997

By Walt Meglasson

"Developing technologies in demolition equipment and processes have produced a newsophistication within the demolition industry. Yet, with increasing frequency, owners,architects, engineers, and contractors reject out of hand one of the safest and most effectivetools in the demolition industry today, specifically the use of explosives and blastingtechniques in man_made structure removal. The use of explosives in any application mustbe considered as a tool, no more or less dangerous than any other type of tool, when usedproperly. Accordingly, importance must be attached to recognizing the skill, integrity, andcare of those who use it. Massive amounts of information and help are available to assistthe rock blaster, ranging from the practical to the highly theoretical, but very littleinformation exists to guide anyone considering unleashing the power of explosives instructural demolition blasting. The planning and work required to execute such projects iscomplex, and the recognition of the different applications explosives can be applied to isthe first step."

Jan 1, 1993

By Charles H. Dowding, Catherine T. Aimone

Rock particle sizes were measured at fourteen steep-slope Appalachian coal mines during production blasting. The distribution of rock sizes shows the effects of inter-hole timing, sequence of hole initiation, as well as charge distribution within each shot. Blast design parameters were selected to: (1) minimize displacement of broken rock conforming to throw control required of mining methods, (2) minimize seismic effects, and (3) create breakage at a cost economical to mining operations.

Jan 1, 1983

By Martti Hagfors, Jussi Saavalainen

The underwater explosions has been used as a test method for the determination energy content of explosives. The test method is suitable for all kind of explosives; homogeneous, heterogeneous, wa-ter-resistant, no-water resistant, cap sensitive, booster sensitive, explosives with hard confinement, explosives without confinement etc. It is also the only test method by which shock, gas heave and to-tal energy values of the explosives can be measured separately. This feature makes it possible to use the test method to develop the explosives for different purposes; the military high explosives need more shock energy where as the gas heave energy is very important feature for the blasting and sea mine explosives.

Jan 1, 2010

By James L. Wilcox, Douglass P. Bacon

As the U.S. Environmental Protection Agency (USEPA) and state regulators increase the stringency and enforcement of regulations concerning emissions produced by open-air detonation of energetic materials, research must provide the means of obtaining emissions data. The BangBox emissions testing program established the technical foundations for emissions characterization which have been accepted by the USEPA and other regulatory agencies; the technical issues remaining are nettlesome and require new approaches in test procedures.

Jan 1, 1996

By Ruilin Yang

The vector sum peak particle velocity (PPV) of blast vibrations describes the blast vibration intensity more completely than the PPV of a single component waveform. It is more logical to use a vector sum PPV as a vibration limit than using a single component PPV. In 1980 the USBM recommended the frequency related peak particle velocity criterion. So far this method has been only applied to single component waveforms, but not to the vector sum PPV since there is no method available to associate a frequency to the vector sum PPV. The present paper describes a method to define a principal frequency associated with vector sum PPV. The method is based on the weighted average of the principal (zero-crossing) frequencies of the three tri-axial components at the time of the PPV.

Jan 1, 2015

By Stuart Brashear, Steven Bell, Donald Smith

This Limestone site required the removal of a bench containing high quality rock located in close proximity to sump and pit pump. The sump and associated electrical box were below the bench that needed to be blasted and located only 70 feet (21.33 meters) away. It was proposed to blast material needed without moving or disturbing the pump or electrical junction box. The area to be blasted was flown with a drone and stitched into a 3D orthographic model. Proprietary blast design software was used to create a blast design solution that would allow for a series of blasts that would provide required fragmentation and muckpile development and not disturb the sump or electrical box. A drill patten was created for each blast using the burden heat map and 3D face profiles created from the 3D orthographic model. Timing contour lines and muckpile displacement predictions were used to create timing sequences for proper face movement away from the sump and electrical box. The shot designs were laid out with a GPS system to insure hole location accuracy. All holes were remeasured for proper face burdens using the 3D model and Boretrak®® data collected after drilling operations were completed to insure hole locations were within face burden tolerances as derived by the burden heat map. After each drill log was reviewed, a charge loading scenario was created for each hole. The timing design created, for each shot and was reviewed and adjusted as needed with regard to desired muckpile displacement away from the sump and electrical box. Blasting results were satisfactory, with fragmentation and muckpile development consistent with the calculated throw from the blast model, with no rock hitting the pump or box and no rocks striking the sump water and disturbing the pump motor.

Jan 21, 2025

By G. A. Walsh, M. Timm, S. M. Geerts

This paper will discuss the effectiveness and the general use of improvised shaped charges. Testing was conducted by the New Mexico Tech Student Chapter of ISEE and held at EMRTC. The first series of tests conducted was to illustrate the performance of different features of the shaped charge. A PVC pipe filled with C4 with no cavity, PVC with an unlined conical cavity, PVC with a copper lined conical cavity and no standoff, and lastly a PVC pipe with a copper lined cavity and a 1.5 cone diameter standoff.

Jan 1, 2010

By Debra Satkowiak, Ronald Thomas

The Institute of Makers of Explosives (IME), a non-profit safety and security organization founded in 1913, is known for its industry best practices, Safety Library Publications (SLP), some of which have been incorporated into rules by regulatory agencies. The IME developed the first commercial storage, quantity distance (Q/D) table titled “The American Table of Distances” (ATD). It was developed by IME’s legacy association in 1910 and was originally based on observations of structural damage from 117 accidental explosions involving small to very large amounts of explosives, primarily dynamite and black powder. In 1930, the IME published a book, compiled by Ralph Assheton, called the “History of Explosions on Which the American Table of Distances was Based”. The distance in feet in the ATD were founded on the measurements at which inhabited buildings sustained substantial structural damage from the accidental detonation of explosives. For example, minor damage such as window glass breakage and the “shaking down” of plaster was not considered substantial structural damage. Other damage to property that was readily repairable was also not considered “substantial.” It was concluded that unless some integral portion of the building was damaged, the occupants would not be subjected to serious risks.

Jan 1, 2017

By Hapsari Rosa, Ross Cowie

Conventional blasting activities in the mining process use various types of explosives, with the primary raw materials being Ammonium Nitrate and diesel fuel. The quality and specifications of the two raw materials significantly affect the performance of explosives. One program from the Indonesian Ministry of Energy and Mineral Resources requires mixing 30% Bio Diesel 30 with 70% diesel fuel oil in several industrial sectors, including mining, to reduce greenhouse gas emissions and stabilize CPO prices. This program aims very well for environmental sustainability and the palm oil business. However, it turns out that this change impacts the performance and results of the blasting process in the mining industry, which is the appearance of fumes. This paper will discuss the tests carried out in the laboratory on Bio Diesel 30, the explosive products used, and rock samples were taken from a mine in East Java, Indonesia. The aim is to determine what factors can cause fumes utilizing a mixture of Bio Diesel 30 with pure diesel fuel. The parameters tested were visual differences, infrared spectrometry, density and viscosity, surface tension and contact angle for Bio Diesel 30, stability test for explosives, and the SEM-EDS method for rock samples.

Feb 6, 2023

By Wesley L. Bender, James E. Murray

Pre-blast surveys are often conducted solely to document existing structural conditions and uncover potential problem areas. This paper presents a case history where the pre-blast survey was also used as a vehicle to initiate a public relations program with the occupants of a large apartment complex adjacent to a major excavation site. The public relations program, in conjunction with good blasting practices, succeeded in keeping complaints to a minimum. The presentation includes an overview of the project, details of the public relations program, some of the blasting methods that were utilized and a recap of the complaints received.

Jan 1, 1988

By Thomas C. Rube, T S. Bajpayee

The Bureau of Mines conducted research to determine the safe operating conditions for using recycled (used) lubricating oil from mining equipment as a partial replacement for diesel fuel to make ANFO-type blasting agents. The use of recycled oil (RO) saves energy, reduces oil imports, and reduces mining costs.

Jan 1, 1996

By M Dandeneau, P I. Rajic, K D. Murphy, M B. Johnson, T J. Tope

"Manufacturers and users of energetic material [i.e., propellants, explosives, pyrotechnics (PEP)] generate unserviceable, obsolete, off-specification, and damaged items that are characterized as reactive waste. These items must be safely treated and disposed of or reclaimed/recycled, thereby controlling existing waste inventories at manageable levels. The most commonly used disposal and treatment method, particularly at U.S. Department of Defense (DoD) installations, is open burning/open detonation (OB/OD). However, regulatory constraints and the inability of operators toobtain permits required for treating these waste has led to the recent reductions and limited use of OB/OD treatment at many installations."

Jan 1, 1995

By R. K. Wharton

A European Directive requires that an explosive which is sold or transported within Europe must meet certain essential safety requirements from 1 January 2003. The assessment and certification of such an explosive is undertaken by an Explosives Notified Body and if the explosive meets the requirements a certificate is issued that allows the affixation of a CE mark. The presence of a CE mark ensures the product free access to European markets. The paper examines the requirements of the Directive, identifies those explosives that come within its scope, considers the role of an Explosives Notified Body, and explains the process of applying for certification.

Jan 1, 2002

By Christoph Muller, Geoffrey Liggins, Mohan Hensman

Modern commercial blasting is as much a technical process as it is a business one. As with most processes both aspects of blasting are driven by and generate new data. The time-critical nature of commercial blasting in mining and construction projects, dictate the timely exchange of information so as not to impede production or commerce. Up-to-date information about the blast to be undertaken can help suppliers: meet customers’ expectations to address challenging ground conditions; react to a market where quickly changing orders occur regularly; and address as-drilled blast patterns as opposed to baseline plans. “Real-time” data exchange into and out of the blasting process supports the whole-of-mine data management that the industry is migrating to.

Jan 1, 2010

By G. Walsh, L. Wolkovitch, A. Savage, V. Romero, T. Zimmerly, G. Imahara, J. Hyneman, K. Byron, D Tapster, S. Belleci, J. Metzger, M. Stanley

Testing was conducted at the Energetic Materials Research and Testing Center for the MythBusters on three separate occasions. This testing included (1) an experiment designed to create diamond from graphite using the shock and pressure of a detonation, (2) the flattening of a car using a steel plate driven by a rocket sled, and (3) the bifurcation of a car also using a rocket sled. All tests were successful; diamond was produced following the detonation of ANFO, and extracted from a graphite / cobalt matrix. A plate was accelerated to 646 mph (1040 km/hr) using a two-stage sled system loaded with 5” (12.7 cm) high velocity aircraft rockets (HVAR) into a car, which was subsequently demolished. Finally, a steel wedge was pushed to 541 mph (871 km/hr) by a one stage sled using HVAR rockets, and was able to cleanly cut a target car in half.

Jan 1, 2010