Search Documents

By P. H. Morris

The exponential delta profile equation matches the profiles of a wide range of coal and metalliferous subaerial tailings deltas well, but the original model implies unrepresentatively low solids concentrations. A revision, based on analysis of the governing equations of mobile bed flows with high concentration values, has shown that for exponential delta profiles to form there must be quasi-steady, slowly varying flow and slow deposition as well as tailings with a log-uniform sorting-parameter distribution. Deposition on tailings deltas is slow and the flow in many natural streams and, by analogy, tailings deltas is quasi-steady and slowly varying; the assumption of such flow is justified by the strong congruence of the revised model and the available data. The predictions of the theoretical model are essentially unchanged but concentration and flow Froude number are now not explicitly limited

Jun 19, 1905

By P. H. Morris

The profile of a delta formed by fine-grained mineral processing wastes, disposed of as aqueous slurries by subaerial deposition from a pipeline, has a significant bearing on the volume that is available for waste and water storage in a given containment structure. Earlier field data and laboratory experiments suggested that mine waste delta profiles could be predicted with high levels of accuracy using data from small-scale laboratory deposition tests. The relationships between the profiles of full-size and laboratory-model deltas were analysed using the principles of kinematic similarity and a recent theory of delta formation based on engineering hydraulics. Measured profiles of full-size and model coal-mine tailings deltas are compared and the prediction of full-size profiles discussed. It is shown that the data-derived laboratory-model deltas are insufficient to allow accurate prediction of full-size delta profiles. Initial slope data or other, equivalent data for the full-size delta are also required

Apr 1, 1996

By T. Ogasawara, J. P. Barbosa, A. J. Monhemius, F. T. Da Silvia

A thermodynamic analysis of the sulphation of rare-earth phosphates and the water-leaching of rare-earth sulphates was used to guide experimental work on the sulphation and leaching of concentrates from Pitinga. It was concluded that the sulphuric acid digestion of xenotime is technically feasible and could be used industrially to produce yttrium and other rare-earth oxides. Yttrium extractions of more than 90% were obtained by digestion at 503 K for 4 h at an acid:concentrate ratio of 2:1 with particle size -0.053 mm. The apparent activation energy at temperatures less than 473 K, as determined from the Arrhenius plot, was 11.0 kJ/mol, indicating that the reaction is controlled by the diffusion of the reactants or products through the sulphate layer

Jun 19, 1905

By M. Lombardero, J. Garcia-Guinea, J. Taboada, B. W. Roberts

The structural, textural and mineralogical properties of the slate formations of NW Spain make it the most important district in the world for quarrying roofing slates. Over the past 10 years the introduction of new methods has increased yields from 2 to 13%. The main factors affecting quality are quartz grain size less than 75 micrometres, homogeneity of slaty cleavage and S0-S1 intersection angle, very low metamorphic grade, absence of secondary foliation, beds 10-12 m thick and low content of oxidisable Fe sulphides. The two main controls on fissility are lithology and deformation accompanied by metamorphism. The minimum natural block size should be 0.6 m3 but this volume can be reduced for modern cutting tools such as diamond wire, chain and circular saws. Structural analysis is crucial in exploration and quarrying, as shown by the prospecting methodology applied at Dominio de Truchas in central Spain and the computer analysis of rock mass discontinuities at Casaio quarry

Jun 19, 1905

By J. E. Misiewicz, A Rozendaal

Paper presented at Geofluids '93, held in Torquay, UK, 4-7 May 1993. The tin field consists of a fragment of Lower Proterozoic volcanosedimentary rocks surrounded by granitoids. Almost all the significant deposits are hosted by arkoses and are classified as replacement and space-filling types, with particular styles of mineralisation dominating at different mines. Petrological and geochemical investigation of borehole cores from four centres indicated the presence of a stratified zone 500-600 m thick and continuous over at least 20 km along strike, consisting of pervasively altered clastic arenitic sediments. The alteration is zoned into a grey-green sodic albitised footwall, an 80 m thick sericitised-tourmalinised sulphidic tin zone and a red haematitic potassic hanging-wall. The zoning and the localisation of three cassiterite phases are consistent with the tectonic history and with multiple pulses of stanniferous hydrothermal fluids derived from late differentiates of the granites over a prolonged period. Areas of high fracture density acted as conduits for the fluids, whose initially rapid ascent was retarded by decreasing pressure contrast, limited development of fracturing and/or impermeable shaly arkose to cause lateral spreading and pervasive alteration over a broad, stratified front. Lateral overlapping of local fronts at the various centres suggests a continuous zone, while the many petrological and geochemical similarities point to a shared fluid composition

Aug 1, 1995

By J. Crummy, I. K. Anderson, A. J. Hall, R. S. Haszeldine

Bedrock gold mineralisation has been located in association with an extensive float train 25 km west of known alluvial gold. It is in the form of open, matrix-supported breccias comprising pyritic quartz/sericite clasts in a vuggy, cherty chalcedonic and crystalline quartz matrix. Fluid inclusions in pyritic clasts indicate trapping temperatures for gold mineralising hydrothermal fluid of 170-240 degrees C. This mineralisation could represent the upper part of a feeder zone to an exhalative hydrothermal system. It is possible that other high-level feeder zones could be preserved elsewhere in the area. Deep weathering of such a system could provide a source for the alluvial gold localities near Helmsdale. It is suggested that east and central Sutherland presents good prospects for exhalative epithermal gold mineralisation and the associated feeder zones

Jun 19, 1905

By A. D. Mukherjee, H. N. Bhattacharya

Middle Proterozoic sulphide ore mineralisation occurs in isolated blocks of the NE-SW trending Delhi fold belt composed of Delhi Supergroup rocks. The Ajari-Basantgarh-Pipela belt forms part of the longest, widest and westernmost tectonic unit of the Delhi fold belt and consists of amphibolites, metapelites, quartzites and carbonates. The metapelite lenses and associated amphibolites host pyritic copper mineralisation. Mineralisation takes the form of sheet-like bodies consisting of ore lenses of various sizes interlayered with host or associated rocks. Massive, banded and disseminated varieties of ore are found. Pyrite is dominant with subordinate chalcopyrite and sphalerite. Pyrrhotite, galena, cubanite, mackinawite, marcasite and freibergite constitute the minor minerals. The characteristic features of the ores suggest a possible correlation with Besshi-type deposits, and the closely associated amphibolites are interpreted as low-K tholeiites of a fore-arc setting

Jun 19, 1905

By A. E. Tercan, D. Mamurekli

Ordinary kriging on the assumption of a gaussian error distribution and indicator kriging were used to derive the probability that a given calorific value would or would not be exceeded by coal from an area of a deposit. The two techniques led to similar probability maps despite local differences; the lack of an absolute reference makes it impossible to judge which method is better for this particular application

Jun 19, 1905

By G. B. Harris, A. R. Laplante

Fine tungsten was used to mimic gold and fine and coarse silica and magnetite to mimic gangue. The optimum flow rate of fluidisation water varied from 1.7 l/min for fine silica to 5.6 l/min for coarse magnetite. Overloading at optimum flow rate was then investigated. With fine silica gangue no overload occurred under any of the conditions studied, and there was very little overload with fine magnetite. Coarse silica caused appreciable overload, but only after a significant bed of tungsten had been formed; with fine magnetite gangue the onset of overloading occurred earlier. Finally, with coarse magnetite severe overloading occurred almost immediately. Overloading was modelled using a first-order kinetic rate constant for erosion of the concentrate bed and a critical mass of constant above which it takes place. The results clearly demonstrate the importance of removing oversize to maximise recovery, particularly with a high-density gangue

Jun 18, 1905

By D. C. Goldring

Many high-grade iron ores are considered to result from the supergene enrichment of banded iron formations. The secondary processes may be related to either present-day or ancient erosion cycles and may reach a considerable depth. Other high-grade ores hosted by banded iron formations are regarded as either sedimentary or metamorphic in origin although often also subjected to the secondary processes. The evidence for this multiplicity of origins is reviewed with descriptions of selected deposits: Kedia d'Idjil and M'Haoudat in Mauritania, Bomi Hills and the Nimba Range in Liberia, the Itabira district in Minas Gerais, Brazil, and El Pao in eastern Venezuela. Emphasis is placed on the recognition of textures that show that some ores are tectonites, the precursor materials having undergone pervasive deformation accompanied by metamorphism. The question whether such ores are pre- or syntectonic is difficult to resolve, the evidence being inconclusive, but a diagenetic/early deformation origin is preferred. The possible range of origins has to be taken into account in exploration, particularly as regards the depth of drilling, and in the characterisation of ores for metallurgical use

Jul 1, 1991

By A. R. Naderian

Laboratory strength and deformation testing of freshly blasted sandstone and claystone overburden from Jeebropilly colliery in Queensland and in-situ plate-bearing tests on four backfills of different ages showed that the bearing capacity of backfill is a function mainly of compaction, not of age. The modulus or stiffness of the backfill is significantly increased by previous loading, in some cases up to threefold. Backfill material experiences some compaction through the passage of mining vehicles, likely to provide a bearing capacity that will support normal construction activities; the limited testing performed suggested that completed backfills are capable of supporting loads of up to 200 kN/m2 while sustaining displacements acceptable for a wide range of residential and industrial uses, but may be susceptible to collapse settlements due to saturation in the long term

Jun 19, 1905

By N. Krauland, A. Nystrom, M. Board, S. Sandstrom

Several deep Swedish cut-and-fill mines experience severe ground control problems, including roof collapse and wall sloughing, as a result of variable rock quality and high in situ stresses. A project to examine the problem included two main areas. The first was prediction of mining conditions at depth and the adaptation of cut-and-fill mining to such conditions; the second was the assessment and improvement of support methods at present and future depths. Simple, elastic, mine-scale numerical models were used to optimise stope sequencing and more detailed, stope-scale models to simulate the failure processes around a stope and the interaction of rock mass and support. Kristineberg was chosen for testing and calibration of the predictive methods because of its long history of severe ground conditions and the large base of observational and monitoring data available for comparison. Horizontal cut and fill was found technically suitable to depths beyond 1 000 m and economically viable if ore value covers support costs. Stability can be achieved with the present support technology down to 1 000 m but the 7-strand 15.2 mm cables have poor deformation properties (5% failure strain) compared with rebar rock bolts (17%). Reducing the intervals between levels from 100 m to 50 m will cut support costs and improve production reliability and capacity. Simulation of sill-pillar mining indicated that conditions would be most severe when pillar height was reduced to 15-20 m; mining of a sill pillar has been carried out successfully to the last 3 m, whose extraction is planned for the near future

Dec 1, 1995

A production drill rig at a site in Sweden was equipped with a monitoring system to estimate production statistics. Drill running times, drill hole depths, penetration rate, rotation speed, thrust, air percussive pressure and torque pressure were recorded for every 10 mm of hole length for a period of 5 months. Operational activities (rock penetration, tube handling, moving and set-up time) accounted for almost 62% of the time consumed, the remaining 38% being different types of stoppage. Drilling itself, as opposed to handling, took less than 24% of the total time. The results give an indication of how the overall drilling capacity can be increased and which activity should be emphasised. The impacts of automation, new developments and reorganisation on production can also be predicted. Average production was found to be around 100 m/day, but varied between 50 and 160 m/d. The company's specification for the drill rig, before purchase, was that an average production rate of 130 m/d be attained over two consecutive months of drilling - a rate which monitoring shows will not be achieved

Jun 19, 1905

By M. V. Swain, N. Bristow, R. D. Dukino

During mining, crushing and handling the size of iron ore lumps decreases. Key factors in determining the amount and size of fines that are produced are the mechanical properties of the ore. In a continuation of earlier work on the same ores the mechanical properties of three Australian iron ores from Yandi, Koolan and Mt. Whaleback were determined. In particular, fracture toughness was investigated in greater detail by examining its relationship to crack length using the compact tension test. The elastic modulus and strength of the ores were also determined in flexure and compression. The results were interpreted using Weibull statistics, enabling the ores to be ranked according to strength and elastic modulus. These results, together with data on the mechanical response of the ores to stress and observations concerning the effect of mineralogy on cracking, provide a coherent understanding of the mechanisms involved when the ores fracture

Jun 18, 1905

Two concentrates from Palabora, in South Africa, containing 0.056-0.068% undesirable Cu and 0.8 or 2.2% Ti, were chlorinated with air:chlorine ratios of 10:1, 15:1 and 20:1 at temperatures between 1 200 and 1 329 K. The resulting volatile chlorides were condensed and the solutions analysed for Cu, Fe and Ti. Recovery of Cu was less than 25% at low temperatures and short reaction times, but at 1 258 K almost all Cu was removed from the magnetite at all ratios of chlorine to air. At higher temperatures, the increased carrying over of iron as FeCl3 could be minimised by decreasing the partial pressure of chlorine. No titanium was detected in the volatile products and the percentage of Cu recovered was independent of Ti concentration in the concentrates, though as a function of Cl2 vol%, more Cu was recovered at 1 200 K from the low-Ti than from the high-Ti concentrate. In a fluidised-bed reactor, Cu recovery was 58-90% and iron carry-over less than 10 ppm

Jun 21, 1905

By C. A. Pickles, J. M. Toguri

The refining of two molten Ag-Cu alloys, containing 7.5 and 11.2 mass% Cu, with a borosilicate slag was investigated using both air and pure O2 to determine the effects of the following variables: flow rate of oxidising gas; injection time; mass of sodium borosilicate flux; and injection of the oxidising gas into either the slag or the metal. The results demonstrate that more than 90% of the Cu can be removed with Ag losses of less than 5% and that refined metal with a Cu content of less than 0.5 mass% can be produced. Ag losses to the slag increased with the amount of Cu removed, and a mechanism is proposed to account for this

Dec 1, 1995

By D. M. Evans, D. L. Buchanan

Paper presented at the IAGOD international symposium on mineralisation related to mafic and ultramafic rocks, held in Orleans, France, 1-3 September 1993. The Zinca area was chosen as a suitable location for an investigation of the weathering and secondary dispersion of platinum group metals from the Zone. It was concluded that platinum is immobile while within weathered rock, its mineral phases tending to alter from primary sulphides and tellurides to secondary Pt-Fe alloys. Palladium is variably mobile in weathered rock. In stream sediments Pt occurs mainly as small, dense, discrete particles, giving rise to a nugget effect, whereas Pd probably occurs as much finer particles or chemically adsorbed on to a suitable substrate. Pt shows a rapid decrease in sediments downstream from mineralisation, whereas Pd has a much slower downstream decay

Apr 1, 1994

By D. W. Holliday

The major deposits of anhydrite and secondary gypsum in Jamaica occur discontinuously at a single horizon within the Lower Eocene succession of southeast Jamaica. They are not intruded from other horizons of different age, as has previously been supposed. The gypsum and anhydrite occur in a regressive sequence at the junction between marine (Richmond Formation, Halberstadt Volcanics, Halberstadt Limestone) and overlying non-marine (Wagwater Formation) sediments. They are thought to have been formed in an arid supratidal (sabkha) environment. A variety of 'nodular' structures occurs in the gypsum and anhydrite which can be related to early diagenetic processes and compaction effects. All gradations exist between single isolated anhydrite nodules and structureless anhydrite due to closer packing and coalescence of nodules. The structures and textures in the anhydrite are thought to be consistent with penecontemporaneous formation from gypsum crystals rarely more than 2 cm in diameter. Single anhydrite nodules are not usually larger than 2 cm; nodules of greater size are compound, due to the coalescence of several smaller nodules. Some large compound nodules may have developed from single sand crystals or rosettes. Compaction of anhydrite appears to have been largely mechanical, but some rocks have an aligned fabric, suggesting later flowage

Dec 1, 1971

By G. J. Hearn

between particles in the classifying region is then

Apr 1, 1995

By H. Y. Sohn, Hang Goo Kim

Computer simulations were carried out using calcium ferrite slags containing 25 wt% CaO, and the results compared with those obtained using fayalite slags. There was little difference in overall elimination of Pb and Bi, but elimination of Sb and As was much lower with calcium ferrite slag. When calcium ferrite slag is used only in the converting stage and fayalite slag in the smelting stage, as in the Mitsubishi process, the contents of Sb and As in the blister copper can be kept to reasonable levels. This allows advantage to be taken of the considerably higher iron oxide-holding capacity of calcium ferrite slag than of fayalite slag at the high oxygen potential under converting conditions, thus preventing precipitation of magnetite. Satisfactory agreement was obtained between predicted values and observed data from a Mitsubishi converter

Jun 18, 1905