Search Documents

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

The research aimed to compare the chemical analysis (K, Na, Cl) of Iranian concentrate plants, which are the main source of materials corrosion in the pelletizing plants. Cl alongside alkaline elements (especially K) may cause corrosion and plug in the grate plates and other involved equipment. Therefore, it is tried in the processing plants to remove impurities from the concentrate to prevent potential problems in pelletizing and iron/steel making processes. Part of these impurities are existed in the nature of ores and others are sourced in the processing water. Various samples from the largest Iranian concentrate plants including Chadormalu, Gol-e-Gohar, Jalal-Abad and Sechahun were prepared to investigate the possibility of alkaline problems for each samples. The amount of Cl, K and Na of Chadormalu sample was obviously low and therefore no alkaline problem is expected. The Cl content of Gol-e-Gohar sample was high (980 ppm) while amount of K was less (0.008 Wt. %). Due to low content of K, most of Cl will release as Cl2 or HCl and so problems caused by KCl plugging would not be a problem. The amount of Cl in Sechahun case was nearly same as Jalal-Abad (400-600 ppm), higher than Chadormalu and less than Gol-e-Gohar samples. However, the K content was higher than all samples (0.04 Wt. %). Therefore, the amount of evaporated K would be 2-4 times more than other samples. Since the amount of Cl and K is simultaneously higher than usual iron ores, therefore alkaline problems may be a serious prevention factor for the continuous operation of this plant. In order to solve this problem some counter-measures is suggested and discussed including cleaning system, partial dust enriched with KCl removal and variation in the materials type of involved equipment.

Jan 1, 2018

By Y. M. Zhu, G. C. Gong

"The influences of citric acid (CA) on the flotation behavior of cassiterite using styrene phosphonic acid (SPA) as the collector were studied via single mineral flotation tests, contact angle measurements, zeta potential determinations and solution chemistry calculations in this paper. The results of single mineral flotation tests revealed under the conditions that pH=4 and the dosage of SPA 100 mg/L, the recovery of cassiterite reached 76.78%. The addition of 20 mg/L AC decreased the recovery by 12.42% at pH=4. Contact angle measurements demonstrated the adsorption of CA prior to SPA made the cassiterite more hydrophilic. The results of zeta potential determinations and solution chemistry calculations indicated the chemisorption of C6H7O7- and C6H6O72- filled parts of the Sn site on cassiterite surface and prevented the SPA from getting adsorbed. The hydrophilic effect of AC was stronger than the hydrophobic effect of SPA and the flotation of cassiterite was crippled. INTRODUCTION Tin is an important metal which is widely used in medical instruments, marine engineering materials, electronic and electrical devices, welding, weapon manufacturing and organotin compounds industries (Angadi et al., 2015). Cassiterite is the only mineral from which the tin can be extracted, thus it is of great importance to efficiently exploit the cassiterite mineral. Flotation is an indispensable method for the recovery of cassiterite (Li et al., 2015). However, cassiterite is usually in association with many other gangue minerals which are of similar floatability, such as quartz, calcite, fluorite, iron oxide, wolframite, scheelite and tourmaline (Sreevinas, 1997). So some modifiers are necessary in the cassiterite flotation process. The amounts of the modifiers used in the flotation must be judicious and the overmuch modifiers may cripple the recovery of cassiterite (Parsonage et al., 1987). Nevertheless, the research about the effects of the modifiers on the flotation behavior of cassiterite has been rarely reported. In this paper, the influences of citric acid (CA) on the flotation of cassiterite using styrene phosphonic acid (SPA) as the collector were investigated by flotation tests, contact angle measurements, zeta potential determinations and solution chemistry calculations."

Jan 1, 2018

By Z. G. Li

The large-scale vibrating screen has been applied widely in coal industry and other industrial areas as a kind of important device. As vibration mechanical device, it works very hardly and works in very bad environment so that the structure of screen is damaged easily. Therefore, it is very important that how to detect the fault of structure as early as possible to make the repair schedule reasonably and economically and to avoid the body hurt and device damage. As a kind of important structure of vibrating screen, the lower crossbeam is the main carrying structure and it is easily damaged, so it is regarded as a researched object in this thesis and it is tested under the load in the laboratory. Based on the test, acoustic emission wave signals can be got-ten by modern acoustic emission testing technique. Then, the ?wavelet packet - energy? from the characteristics of acquiring signals is used as neural network input vector. In the BP network structure design, the design of a hidden layer with variable number of BP network is established. Based on the error by contrast, the best nerve number can be identified in the hidden layer. Through integrated analysis, using Levenberg-Marquard BP study algorithm, network-training errors are relatively small, the acoustic emission signal is used in BP neural network as a pattern of recognition. In Matlab6.5, neural network model identification is created and taking advantage of nonlinearity and the ability of learning and memory of Neural Network, this model is fixed by training structure of network with training samples. The work presented shows that acoustical emission signal processing and research on early fatigue fault diagnosis based on the wavelet and the neural network is viable.

Jan 1, 2014

By M. F. He

There are three polymorphic modifications in pyrrhotite (monoclinic, hexagonal and orthorhombic), with monoclinic and hexagonal polymorph being more abundant. The floatability of different crystalline structures of pyrrhotite (monoclinic and hexagonal) is studied in this paper. It is shown that the floatability difference of monoclinic and hexagonal is obvious and that the flotation recovery of monoclinic pyrrhotite is greater than that of hexagonal pyrrhotite using different collectors . Using butyl dithiophosphate as collector, the flotation recovery of pyrrhotite is higher than when sodium diethyl dithiocarbamate and sodium butyl xanthate are used as the collectors. Monoclinic and hexagonal pyrrhotites are more easily activated by Cu2+ in acidic conditions than in alkaline conditions, while Cu2+ can not activate hexagonal pyrrhotite when sodium diethyldithiocarbamate was used as the collector. By the measurement of contact angle, it is indicated that monoclinic and hex-agonal pyrrhotite float well and are easily activated by Cu2+when dithiophosphate was used as the collector. Using sodium diethyl dithiocarbamate as a collector, the flotation behavior of pyrrhotite was investigated. The relationship between potential and pH range for pyrrhotite flotation was established. The results show that the flotation of pyrrhotite is dependent on pulp potential at certain pH values.

Jan 1, 2014

By E. A. Brocchi

This work is dedicated to the chemical treatment of a typical EAF dust by chlorine content agents. The residue contains 48% Fe2O3 and 28% ZnO mainly in the franklinite structural form. The others less compounds are: 4.00% CaO, 2.60% MnO, 2.20% MgO, 1.08% PbO, 0.36% Cr2O3, 0.21% B2O3, 0.03% CdO and 0.01% NiO. The experiments purpose is selectively to remove zinc from the residue leaving the iron behind. Thermodynamics studies have indicated some roasting possibilities. The experimental results have shown that both HCl leaching and carbochlorination will remove iron and zinc without any selectivity. However, either the chlorine or the calcium chloride roasting seems to form, preferentially, the zinc chloride. So, it will be presented how the EAF Dust can be treated by the using of chlorine roastings process such as carbochlorination in order to separate the zinc and iron present in the frankilinite, main EAF dust content.

Jan 1, 2014

By Z. A. Zhou

In Canadian oil sands processing, flotation is used to recover liberated bitumen droplets from oil sands slurries. Similar to conventional mineral flotation practice, a fundamental limitation of recovering bitumen from low grade oil sand ores is its slow and ineffective aeration of the liberated small bitumen droplets. Gas nucleation and cavitation could provide better mechanisms for accelerating bitumen-bubble attachment. A research program was undertaken to examine factors affecting spontaneous bubble nucleation on bitumen surfaces. The results demonstrate that surface hydrophobicity and existence of gas nuclei in process water play a critical role for bubble nucleation. While there are more bubbles nucleated on highly hydrophobic silanated glass surfaces than on moderately hydrophobic bitumen, bubble nucleation on clean hydrophilic glass surfaces is negligible. Heating process water up to 85 ~ 95oC (as used in commercial operation) or boiling tap water prior to gas nucleation tests is shown to remove sufficient amount of gas nuclei existing in the water, thereby drastically reducing the number of bubbles nucleated on bitumen. Enhancing gas nuclei formation in hot process water is identified as a promising strategy to improve bitumen-bubble attachment during oil sands conditioning, and hence to increase bitumen recovery from low grade ores.

Jan 1, 2014

By Chen Jianhua, Shen Zhenchang, Zhang Ming, Chen Feifei

"With flotation cells scale-up, the performance of flotation cells is increasingly variated for short-coming and dead zones existing. The residence time distribution which shows the movement of tracers can assess the unexpected flows such as short circuit and dead zone in a flotation cell. In this paper, the residence time distribution of pilot flotation cell is investigated with CFD simulation. Based on the theoretical model, the short-coming probability and dead zone probability are quantitative. The ideal average residence time is similar with the actual average residence time. The mixing effect of the flotation cell approaches the ideal continuous stirred tank reactor. The operating parameters such as speed and feed velocity have complicated influence on residence time distribution. The research would be helpful to understanding flow in flotation cell and improving performances of flotation cell.INTRODUCTIONFroth flotation is a method which purifies minerals according to difference of physical and chemical surface characters of different mineral particles (Shen, Z., Chen J, 2012). Flotation cell is a key equipment for froth flotation method. The flotation cell performances have great influences on flotation index.It is difficult to evaluate flotation cell how to improve flotation procedure to complexity.The main flotation cell performances are aeration volume, air dispersion, solid suspension and residence time distribution, etc (Shen, Z., Lu, S., 2008). Residence time distribution is an important fluid hydrodynamics which could reveal the flow of pulp, mixing of particles and air bubbles. In the flotation cell, the ideal average residence time of pulp could obtain easily. But the fluid differential units would be different flow paths. The residence time of the fluid differential units is variation and would be longer or less than the average residence time. The residence time distribution would reveal the mixing effect and predict the not ideal flow in the flotation cell such as shorting cutting, dead zone, etc. As we know, the shorting cutting and dead zone would be decreased the real flotation time and it is disadvantage to better flotation effect, especially for large flotation cell. It is impossible to eliminate the not ideal flow totally. It is very important to reveal and decrease the shorting cutting and dead zone probability in the flotation cell."

Jan 1, 2018

By Chen Jianhua, Shen Zhenchang, Zhang Ming, Chen Feifei

"With flotation cells scale-up, the performance of flotation cells is increasingly variated for short-coming and dead zones existing. The residence time distribution which shows the movement of tracers can assess the unexpected flows such as short circuit and dead zone in a flotation cell. In this paper, the residence time distribution of pilot flotation cell is investigated with CFD simulation. Based on the theoretical model, the short-coming probability and dead zone probability are quantitative. The ideal average residence time is similar with the actual average residence time. The mixing effect of the flotation cell approaches the ideal continuous stirred tank reactor. The operating parameters such as speed and feed velocity have complicated influence on residence time distribution. The research would be helpful to understanding flow in flotation cell and improving performances of flotation cell.INTRODUCTION Froth flotation is a method which purifies minerals according to difference of physical and chemical surface characters of different mineral particles (Shen, Z., Chen J, 2012). Flotation cell is a key equipment for froth flotation method. The flotation cell performances have great influences on flotation index.It is difficult to evaluate flotation cell how to improve flotation procedure to complexity. The main flotation cell performances are aeration volume, air dispersion, solid suspension and residence time distribution, etc (Shen, Z., Lu, S., 2008). Residence time distribution is an important fluid hydrodynamics which could reveal the flow of pulp, mixing of particles and air bubbles. In the flotation cell, the ideal average residence time of pulp could obtain easily. But the fluid differential units would be different flow paths. The residence time of the fluid differential units is variation and would be longer or less than the average residence time. The residence time distribution would reveal the mixing effect and predict the not ideal flow in the flotation cell such as shorting cutting, dead zone, etc. As we know, the shorting cutting and dead zone would be decreased the real flotation time and it is disadvantage to better flotation effect, especially for large flotation cell. It is impossible to eliminate the not ideal flow totally. It is very important to reveal and decrease the shorting cutting and dead zone probability in the flotation cell."

Jan 1, 2018

By de Vaux. D.

Synthetic water with a calcium concentration of 80 ppm and 500 ppm was prepared and the flotation results obtained compared to a simple electrolyte in order to determine the effect water quality has on pentlandite and pyroxene surface alteration and, ultimately, floatability. During the study, the possible effect of interactions between the minerals investigated and Ca2+ ions in the presence of sodium isobutyl xanthate was studied at pH 6 and pH 9 by means of zeta potential determinations, microflotation tests and ToF-SIMS analysis. The results obtained have demonstrated that water quality does play a significant role in flotation recovery at the experimental conditions used.

Jan 1, 2003

By Robinson Irarrazabal, Edison Collinao, Rodrigo de Carvalho, Patricio Davila, Marcelo Tavares

"In recent years, DEM (discrete element method) softwares, along with 3D laser measuring equipment, have become powerful tools to describe mill charge behavior, as well as forces acting on the liners of SAG mills. With the aim of contributing to streamline this application of the advanced technologies ME Elecmetal and Universidade Federal do Rio de Janeiro, UFRJ, proposed a new approach to improve the design of mill liners using elements from mechanistic modeling of grinding. The paper presents a methodology for continuous improvement of liner design, which uses information from the DEM collision energy spectra in the mill discriminated for the different components (ore and steel balls), as well as information on the breakage properties of the ore being ground. From these it proposes the concept of "effective collisions", which corresponds to the collisions that are of sufficient magnitude to cause breakage, thus allowing to discriminate from impacts that do not cause breakage either in a first impact or after repeated loading. It also tracks the collision of steel balls against the shell in order to assess their potential damage to the liners. An industrial case study is presented of a 38’ diameter SAG mill, which was experiencing challenges associated to liner breakage and low efficiency with the old liner design. Through a modification of the liner design, simulations demonstrated the potential benefit associated to reduction in ultraprojection and improvement in mill capacity. Implementation of the new design in the SAG mill was carried out, resulting in increase in daily throughput from 6 to 12%. Further, the time spent in liner change was reduced by 47% given the reduction in the numbers of parts. This operation also benefited from having no stops due to unplanned shutdowns to replace broken tiles. These demonstrate the benefit of coupling advanced computational tools to sound engineering principles in continuous improvement of liners."

Jan 1, 2014

By Hernán Menares, Diego Hernández

"Over the last few years, the copper mining industry has been facing a changing scenario with respect to both the market and society which has resulted in taking a closer look at the way in which mining is being done. The cycle of high metal commodity prices of the last decade left the industry with high costs. Together with increased environmental and social requirements, a decrease in ore body quality, scarcity of resources such as human capital, water and energy, has resulted in an ever-increasing challenge to make a profit out of new ore bodies but also to maintain the current operations in the longer term competitive. The major challenge is to create value for all stakeholders, exploiting ore bodies that nowadays are not considered economically attractive, which applies to both new ore bodies and existing operations, but in a sustainable way. In order to achieve this objective, it is necessary to approach the mining business differently in five main areas: (1) operational efficiency through better use of installed equipment and skilled labor force; (2) efficient use of energy; using opportunities for alternative energy sources and efficient design; (3) efficient use of water; diminishing losses and use of seawater as an alternative source; (4) minimizing environmental impact by eliminating effluents and controlling dust emission; and (5) a more closer, proactive and collaborative relationship with the communities allowing them to be an active player in the solution to assure a sustainable business in the long term. This presentation will show how Antofagasta Minerals is facing these challenges with a long term strategy that includes all of the above mentioned aspects and that is allowing the company to exploit its mineral properties in an efficient and successful way."

Jan 1, 2014

By Tingting Li, Guodong Li, Dezhou Wei, Cong Han, Shuling Gao, Yanbai Shen

"The aim of this study is to solve the problem of tungsten leaching from scheelite concentrate using sodium hydroxide in the presence of phosphate by an autoclaving process, which is one of main development techniques for tungsten recovery. To understand the applicability and leaching performance of tungsten leaching from scheelite concentrate, the main work is to investigate the effects of leaching parameters such as initial concentrations of NaOH and Na3PO4, reaction temperature, stirring speed, liquid-to-solid ratio and reaction time on WO3 dissolution rate to obtain the optimal leaching conditions. The chemical composition and phase composition of the samples were evaluated by means of XRF and XRD. The content of WO3 in the leaching residue obtained via washing, filtering and drying was analyzed by thiocyanate spectrometric method. The optimal leaching conditions were found to be NaOH concentration of 6.76 mol·L-1, Na3PO4 concentration of 1.35 mol·L-1, reaction temperature of 180°C, stirring speed of 400 rpm, liquid-to-solid ratio of 2.0 and reaction time of 90 min. The results showed that tungsten leaching rate of 99.20% was reached under the optimal conditions. The technology exhibited superior leaching performance, which not only reduced the consumption of sodium hydroxide but also greatly decreased reaction time in comparison to a conventional autoclaving process. INTRODUCTION Tungsten is an important strategic metal, which is widely utilized in a variety of industries due to its high melting point, superior mechanical properties and heat-resistant performance [1-3]. The chief raw materials for the production of tungsten in nature are wolframite and scheelite [4, 5]. Among them, approximately two-thirds of the tungsten reserves contain scheelite deposits in the world [6, 7]. With the progressive exhaustion of high-quality wolframite resources, scheelite has become a predominant primary resource for the production of tungsten [8, 9]."

Jan 1, 2018

By I. A. Podkamennyi, O. E. Kovalchuk, G. P. Dvoychenkova

"Using the methods of electron microscopy and IR spectroscopy, mineral components in the run-of-mine kimberlites and on the surface of diamonds were identified. The mechanism and sequence of mineral formation on the surface of diamond crystals were established. Systematization and classification thereof were undertaken for the first time ever.INTRODUCTION The high content of diamonds sized -5 mm in the kimberlite ores of Western Yakutia determines their processing depth in the size class 0.5 mm and finer [1, 2]. These diamonds are recovered by grease and froth separation based on the natural hydrophobic properties of the crystals. When refractory altered kimberlite ores are fed into the industrial process, the performance of grease and froth separation of the diamond ore greatly deteriorates. [4, 10, 15, 17]. Altered kimberlites are known to contain up to 90% of secondary minerals. This reduces by up to 40% the recovery of diamonds by grease and froth separation. [6].Diamond crystals from the grease and froth separation tailings were investigated. On the surface of the examined diamonds, hydrophilic mineral formations were identified, responsible for reduced recovery by physicochemical separation methods [3, 12, 18]. The aim of this study was to identify and describe the relationship between the composition of kimberlite ores and mineral formations on the surface of diamond crystals in order to systematize, classify, and then develop methods of removal in grease and froth separation processes. MATERIALS Following materials were examined in this study: - kimberlites of various material composition, - resulting slimes, - diamond crystals from kimberlite ore processing products."

Jan 1, 2018

By Crasta Jeason, T. Sreenivas, M. Narasimha

The subtle nature of the flow inside the hydrocyclone has encouraged development of mathematical models for predicting its performance, which are widely used in simulation of comminution circuits. But most of the models available are based on single average feed density. But the feed to hydrocyclone classifier is generally mixture of particles of different densities. This effect of varying density of feed particles on performance of hydrocyclone has been reported in literature. Further investigation of the effect of multi component feed on the performance of hydrocyclone is the objective of this work. This work involves experimental work to study multicomponent behaviour in various size cyclones. The performance of hydrocyclone for feed mixture of magnetite and quartz has been studied. The effect of presence of magnetite, a high density material on efficiency of separation of quartz has been analysed. It was observed that the effect of component interaction increases with feed solids concentration leading to an increased cut-size for a given optimum cyclone conditions. Based on the multi-component exiperiments available in literature, a concept for modeling the performance of hydrocyclones is proposed. A set of semi-empirical model equations for cut-size, sharpness of separation are presented. An attempt to validate the new hydrocyclone model on multi-component behaviour is made.

Jan 1, 2014

By John Ralston, Stephen Grano, Yongjun Peng, Daniel Fornasiero

"A specially designed mill which allowed the control of pH throughout grinding was used to study the effect of grinding conditions on galena flotation and galena separation from pyrite. The changes occurring on the mineral surface during grinding were investigated by EDTA extraction and ToF-SIMS measurements.Galena flotation and galena separation from pyrite were strongly dependent on the type and amount of oxidation species produced on galena and pyrite surfaces under different grinding conditions. Iron oxidation species depressed both galena and pyrite flotation, whilst lead oxidation species activated pyrite flotation but had little effect on galena flotation. Optimum galena flotation and galena selectivity against pyrite were achieved by selecting grinding conditions that enabled lead and iron oxidation production to be controlled.Grinding conditions had a large effect on the flotation of the galena particles of different sizes. Flotation of fine galena particles (-10 µm) was depressed by iron oxidation species derived from the grinding media. Chromium grinding medium decreased the production of iron oxidation species and therefore increased the flotation of fine galena particles."

Jan 1, 2003

By Jan Svoboda, Toyohisa Fujita

"The current status and history of innovation in magnetic methods of material treatment are reviewed. The milestones and key drivers of innovation are identified, advantages of magnetic separation in comparison to other physical methods of material manipulation are discussed and reasons for failure to live up to its potential and expectations are identified. The future focus in such diverse areas as mineral processing, waste treatment, recycling and biosciences is discussed and the research and development needs are outlined.Our walk through the innovation landscape in magnetic separation illustrates the enormous effort that has been expended over the years to convert a wealth of novel idea into workable techniques. Remarkable progress has been achieved and numerous successful innovations have been introduced into material treatment operations. On the other hand these techniques have experienced their fair share of failures. The reasons for these cover a wide spectrum of risks that accompany any effort to implement new technology."

Jan 1, 2003

By Gideon Chitombo

"Mining is a "continuous" process of dependent breakage and materials handling stages, from the initial breakage of the in-situ rock, extraction from the pit or underground, and finally to the surface stockpile and downstream processing. Over time, underground and in-pit mining activities diverged into two separate disciplines, each using a variety of in-situ breakage techniques and surface activities, with processing techniques dependent on mineralogy or grades. This artificial separation of underground and open pit activities was exacerbated when the two became increasingly managed as separate cost centres rather than as an integrated unit. Mass mining essentially began in 1903 when metallurgist Daniel Jackling initiated the world’s first open pit, mining system at the Bingham Canyon porphyry copper deposit in Utah. The term mass mining has since been construed to mean large open pits and cave mining methods, including their variants. These methods are largely non-selective, involving the mass extraction of a deposit irrespective of the uneven distribution of grade and mineralogy. The advantages of mass mining have historically applied mostly to low grade, large scale deposits. With the depletion of mineral reserves closer to the surface, however, new deposits are deeper, lower grade and mixed with more impurities. These and other factors make extraction more difficult and costly. Mass mining is moving rapidly into a new and less certain environment where revolutionary changes are required to effectively deal with future challenges which are technical, economic and environmental (licence to operate). This keynote address presents current initiatives being considered for the next generation of both underground and surface mass mining systems in order to significantly reduce lead times and mining costs (CAPEX and OPEX), substantially increase productivity and meet license to operate requirements. The address is designed to solicit discussion on how better integration of mining and processing can become a platform for these next generation of mass mining systems and can also help the industry deal with the future challenges."

Jan 1, 2014

By Paulo Sérgio de Oliveira, Joaquim D. Donda, Andreia C. Rosa

"The search for energy efficient technologies for comminution processes is constant in mineral processing studies, since those processes represent a major percentage of operational costs. In this context the use of stirred mills is increasing, especially for ultrafine grinding. Although many authors claim that these new equipment are more efficient than the conventional ball mills, there were very little chances to prove that in a practical way, since there are few industrial circuits where those technologies perform the same duty. Therefore, the regrinding circuit of Germano second concentrator offers an interesting opportunity: a vertical mill operating in parallel with two ball mills. During almost two years of operation, several sampling campaigns were conducted to evaluate the vertical mill performance and to compare the operational data of the three mills. The industrial data was also compared to jar mill tests results, which are monthly conducted in Samarco labs in order to predict the specific energy consumption required by the ore fed to these circuits. The vertical mill demonstrated the same ability to achieve the product specifications of the ball mills while proved to be able to reduce the medium specific energy consumption in about 40%."

Jan 1, 2014

By Claudio Bisso, Javier Vargas, Charles Lozano

"This paper summarizes the activities performed to predict SAG milling throughput at Minera Esperanza. Having highly reliable geometallurgical models aided by the new computer tools and specific metallurgical testing to rely on has become a major issue in recent times due to their impact on the business. Minera Esperanza’s SAG throughput model was constructed by characterizing the ore feed and operational parameters of the plant. Producing a robust model required satisfying number of requirements for the parameters used for both the ore and the plant as follow: 1) geologic and geometallurgical characterization parameters; and 2) parameters of a plant running at the rated production under optimum operating conditions. Obtaining these parameters required increasing the quantity of samples and metallurgical testing through drilling campaigns, mapping the drill holes and putting samples through various comminution tests while sampling all operational flows at the plant to obtain the metallurgical information for the operational parameters. The information was entered on the JKSimMet software to enable a throughput model to be developed to output SAG mill throughput predictions that are very close to actual throughput figures, i.e., accurate within a range of 2% on a monthly basis."

Jan 1, 2014

By Rainer M. Lotzien, Michael J. G. Battersby, Jan Kleefeld, Julian V. Brown, Rainer M. Imhof

A new flotation system has been developed to improve the generally slow separating differentials of fine bubbles and fine particle suspensions. The new technology is based on established pneumatic flotation designs called Imhoflot which use intensive in-line pre-aeration to aerate the flotation pulp prior to its introduction to the separating cell. In the new system (see figure 1) this separation is speeded up dramatically by the introduction of centrifugal motivation in the separating vessel, without the use of internal moving parts. The design focuses on providing increased differential forces on buoyant mineralised bubbles and hydrophilic fines. The commercial benefit to industry is much reduced residence time, less than 30 seconds, which offers considerable cost savings in equipment and infrastructure.

Jan 1, 2003