Search Documents

By Gilbert Chuah, Peter Middendorp, Joost Bakker, Soon-Hoe Chew

"The Rapid Load Testing (RLT) of foundation piles has been applied worldwide since 1984. Several International and national codes are available, such as the Japanese Code of Practice (2002), ASTM D7383-2010, German recommendation on Piling (2012) and Eurocode (2015). RLT methods like Statnamic and StatRapid are gaining popularity in Asia, Europe and North America. For checking the performance of piles, they are more economical, faster and environmentally friendly than Static Load Testing (SLT), while yielding good correlations with SLT results through an objective analysis method. To date (October 2016) hundreds of piles have been successfully tested by RLT method in Singapore. A number of these RLT tests were coupled with static load testing correlation tests, some of them with instrumentation for shaft load transferred. Examples of some correlation results for foundations installed in various geological formations in Singapore are presented in the paper. The findings from these results indicate that loading rate effects are negligible for Rapid Load Test results when foundations are socketed in competent non-cohesive soil layers and derive most of their capacity from these soil layers.INTRODUCTIONRapid Load Testing (RLT), by which a quasi-static load is applied to a foundation pile, is used increasingly as an alternative to Static Load Testing (SLT) for cast in-situ piles, such as drilled shafts or bored piles. It is recognized nowadays that the determination of the pile capacity with Dynamic Load Testing (DLT) through signal matching techniques such as CAPWAP, TNOWAVE and AllWave-DLT, yield a wide spread of results for cast in-situ piles (Stahlmann et. al, 2012), making it practically very difficult, if not impossible to calibrate the DLT results with SLT results. This spread is due to the empirical and subjective assumptions that are used to interpret the test data, especially for cast insitu piles (Holeyman et al. 2001, Viana da Fonseca in 2008, Herten et al, 2013). This is further complicated by the inhomogeneity of the concrete and variable cross-sections over the pile length for the cast in-situ piles."

Jan 1, 1900

By Gisele R. Passalacqua, Taylor Malangone, Subhash Mahali

New York City is a busy metropolis with 8 million people. New York has the largest public transportation system with 6 million riders a day throughout the subway system. Keeping this infrastructure in service is vital to the overall economy of the region. Hurricane Sandy proved to have a devastating impact on infrastructure in Metropolitan New York. New York City Transit is on the forefront to provide resiliency and maintain its facilities with the use of flood protection systems. This paper presents flood protection structures utilized at Hammels Wye substation site in Far Rockaway, Queens, New York. The site is in close proximity and surrounded by water. The subsurface conditions consist of loose silts overlain by medium dense glacial sand. The high groundwater level combined with limited access to the site presented challenges. A flood protection system consisting of flood walls was recommended for this site. In certain areas the flood walls consisted of retaining walls supported on micropiles. For other areas, the flood walls consisted of steel sheet piles with jet grout columns to reduce seepage below the walls. The effect of driving sheet piles with vibratory hammers on nearby existing structures is always a concern. Recently, hydraulic hammers with variable moment/frequency are being considered as a mean to reduce vibration effects during driving. In this project, an instrumentation testing program was performed to measure peak particle velocity during sheet pile driving utilizing the variable moment vibratory hammer. Plots of peak particle velocity versus frequency were generated. This paper will present the design aspects of the flood walls and construction challenges during installation. This will prove beneficial to engineers in both design and construction fields.

Sep 8, 2021

By Mohammad Ali Rowshanzamir, Mehdi Aghayarzadeh

"This article is an effort to improve our understanding of the performance of geogrid retaining structures (GRS) through numerical analyses. The numerical modeling utilized a commercially available finite difference program, FLAC3D. In this context an extensive parametric study has been carried out on two different GRS walls (vertical reinforced block and inclined reinforced block) to investigate the influence of internal design factors such as soil strength properties and reinforcement stiffness on the performance of these walls. The main purposes of the parametric study were to (1) investigate the sensitivity of the modeling results to the input material properties, (2) examine the influence of the internal design factors on the performance of GRS retaining structures, and (3) improve the internal design of GRS walls on the basis of the working stress information obtained from the parametric study. Based on the analyses results, it was revealed that GRS walls with oblique reinforcement and reinforced block (rotated against natural backfill) have much better performance in terms of reduction in the stresses and strains of reinforcing elements as well as decrease in the wall lateral and vertical displacements in comparison with vertical reinforced block (conventional wall). For example, with 12° inclination of the wall reinforced block there was 50% reduction in the backfill settlement. Also increasing the reinforcement stiffness amount from 10MPa to 50MPa decreases the wall face displacement more than 50% in both GRS walls.INTRODUCTIONOver the past few decades, Geosynthetic- Reinforced Soil (GRS), a soil mass reinforced by geosynthetic layers to restrain the soil lateral deformations, has been employed in the construction of many types of earth structures, including retaining walls, embankments, slopes and bridge abutments. In fact GRS structures are typically more flexible (hence more tolerant to differential settlement), more adaptable to low quality backfill, easier to construct, require less over-excavation, and more economical. Nevertheless, there is a need for an accurate design tool that can predict the performance of GRS structures under working stress conditions and can predict their failure loads as well.Many studies have been published on the performance of the soil reinforced walls such as Isabel et al., 1996; Bathurst et al., 2000; Kazimierowicz-Frankowska, 2005; Nernheim and Bathurst, 2008; Chen and Chiu, 2008 Correia et al., 2012; Erlich et al. 2012. Several numerical studies have also been made throgh finite elements and finite difference techniques on reinforced soil retaining walls to analyze the wall deformations (e.g. Hatami et al. 2001& 2006, Liu and Won 2009, and Abdelouhab et al. 2011). A limited laboratory research has been reported indicating of improving effect of tilting face on GRW performance (Chen and Chiu, 2008). However no major numerical study was found on the effects of face or reinforcement tilting."

Jan 1, 2017

By Karl A. Higgins, Michael D. Venezia

The South Capitol Street Corridor Project is one of the District Department of Transportation’s (DDOT) largest projects, and is currently under construction. This case study will focus on the design of the foundation piles for the main spans of the iconic Frederick Douglass Memorial (FDM) Bridge, and will include a discussion of the foundation design evolution from an originally designed alternative foundation system (i.e. coffer dams and drilled shafts), to the current use of driven Large Diameter Open End Pipe (LDOEP) Piles. The paper will provide a discussion of the design methodology used during preliminary engineering and final design, and will highlight insight gained from the extensive load testing program completed to date. The load testing program consists of a combination of high strain dynamic testing (PDA), as well as Statnamic Load Testing on select sacrificial, pre-production test piles. Specifically, data gathered during the nearly-completed load testing program suggests the development of significant internal shaft frictional resistance within the tested LDOEP Piles. This paper will also discuss limitations of currently accepted industry design methods for predicting the capacity of LDOEP piles, a subject that is also currently being researched by FHWA. The data from this test pile program will help design assumptions for future projects. INTRODUCTION The Frederick Douglass Memorial (FDM) Bridge carries South Capitol Street across the Anacostia River in Southeast/Southwest, Washington, DC, and is owned and maintained by the District Department of Transportation (DDOT). The existing FDM Bridge is nearly 70 years old, serves as a major artery into the city, and has been classified as functionally obsolete. As a result of the condition, age and limitations of the existing bridge structure, DDOT deemed it necessary for complete replacement of the bridge. The replacement project consists of the construction of a new bridge traversing the Anacostia River, as well as the reconfiguration of the Suitland Parkway and I-295 interchanges located at the eastern terminus of the FDM Bridge. Final design and construction services for the replacement project were procured by DDOT through a Design-Build contract. This paper will focus on the driven Large Diameter Open End Pipe (LDOEP) Piles used for support of the main span of the new FDM Bridge which is currently under construction. Discussion regarding the LDOEP Pile design methodology has been included, along with commentary regarding currently available industry guidance related to design and construction of LDOEP Piles. Much insight has been gained during the mostly-completed and extensive load testing program which consists of a combination of high strain dynamic testing (PDA), as well as Statnamic Load Testing on select sacrificial, pre- production test piles. Specifically, data gathered during the mostly-completed load testing program suggests the development of significant internal shaft frictional resistance within the tested LDOEP Piles.

Jan 1, 2019

By Gary L. Seider

Chance, a Division of Hubbell Power Systems, Inc., in conjunction with Sailors Engineering, Inc. has updated its Helical Design Capacity Software. This latest version, ?HeliCAP® v2.0?, is a state-of-the-art helical anchor and pile capacity program designed to operate in the Microsoft® environment. The program calculates the tension and compression capacity along with the frictional capacity, if applicable, of CHANCE® Civil Construction helical anchors and piles using design theories and methods adopted by Chance. This paper details the current state of practice employed by the software in the design methods and installation methodologies of helical anchors and piles.

Jan 1, 2007

By Patrick Granitzki, Alicia Plinio, Janitha Batagoda, Peter Howell

The City of Newark is making a comeback with new mixed-use multi-storied Residential Development projects. The majority of developers tend to use driven H-pile deep foundation systems to support their super-structures. A different approach was recommended for one particular new development near the Passaic River. The surficial geology included glacial deposits consisting of loose to dense sand overlaying relatively soft silt and clay and a lower stratum of medium-dense sand. During a preliminary site investigation for the project, bedrock was encountered at depths ranging between approximately 168 feet to 182 feet below the ground surface. Design capacity required a single pile of 200 tons. Two different pile foundation systems were evaluated in conjunction to the typical driven H-pile system in order to review potential costs and construction schedule impacts. The two alternative pile systems evaluated were tapered tube piles and drilled displacement piles. Theoretical calculations were followed by in-situ load testing. The field testing results indicated the use of drilled displacement piles as the best option for a portion of the proposed building. This paper discusses the different piles systems considered, installation and using drilled displacement piles to minimize cost and optimize construction.

Sep 8, 2021

By Jeff Hopple

"Bluestone Dam in Hinton, W.Va., along the New River, is owned and operated by the U.S. Army Corps of Engineers (USACE). Completed in 1949, the dam is 165 ft (50 m) tall, 2,048 ft (624 m) wide, and encompasses a water shed that is 4,600 sq mi (11,914 sq km). The Bluestone Dam Safety Assurance (DSA) Program began in 2001, and is a multiple-phase construction project to upgrade the capacity and stability of the structure to meet the probable maximum flood event. Installing 216 high capacity rock anchors was a major feature of the work.The USACE selected Brayman Construction Corporation to perform Phase 2B of the construction modifications to the Bluestone Dam. Brayman was responsible for installing the high capacity rock anchors, which range in size from 3 to 61 strands and have a design load up to 2,145 kips (9,541 kN). Drill holes range in size from 6.5 to 15 in (16.5 to 38 cm), and required full length corrosion protection. Of the 216 anchors, 57 were installed on top of the dam to resist overturning and the remaining 159 were installed on the face of the dam at a 45-degree angle to resist sliding.To gain access to the face of the dam anchor locations, the project required dirt benches, excavations with temporary shoring, and steel platforms. To access anchors on the east and west abutment faces, the team excavated over 10,000 cu yds (7,645 cu m) of material. Support of these excavations included the design and installation of three soil nail walls with over 145 nails and 3,500 sq ft (325 sq m) of shotcrete. The project also called for a 780 ft (237 m) long steel platform to gain access to the spillway anchors. The Stratus Group designed the platform to support two 85 ton (80 tonne) crawler cranes and as many as five drill rigs that were the equivalent to a design load of 3.5 ton per sq ft (335 kN per sq m). Once the final platform design was approved, fabrication of roughly 3 million lbs (1,360 tonnes) of structural steel began. Brayman’s in-house fabrication shop, in conjunction with Dura-Bond Industries and Advantage Steel, collaborated to fabricate and install the platform in less than five months. Flexibility in the platform design allowed for sections of the platform to be lowered as much as 16 ft (4.9 m) to provide access to anchors at lower elevations along the spillway face. In addition to the main spillway platform, Stratus Group, Brayman, Dura-Bond and Advantage designed, fabricated and installed six other unique platforms to facilitate anchor construction on various areas of the dam."

Jan 1, 2014

By Dan Yang

Pile foundation designs are performed routinely based on geotechnical information available at the time of design, often with due consideration of large uncertainties inherent to soils and site conditions. These uncertainties frequently are the causes of piles being installed not the same as those designed, especially by factors beyond quality assurance and quality control. With a variety of both satisfactory and unsatisfactory pile test results from these nonconforming piles, the design engineers are required to examine the foundation performance as a whole against the project design requirements before signing off on them or calling for potentially costly remediation. Over the years, as-built analysis has been a consistent way of dealing with pile non-conformity and damage in our practice, avoiding many construction delays and it is an integral part of our pile foundation design. In this paper, the key elements of an as-built analysis along with several major bridge projects are presented.

Jan 1, 2010

By Justin Phillips

The redevelopment of Bow Bells House in London has thrown up a number of challenges that will increasingly be faced by developers of congested sites. In the context of pile reuse this paper examines four key issues: 1. The Developer?s perspective on sustainability, cost, programme and risk management. 2. The nature of pile testing including timing, the balance of extent of intrusive works whilst retaining the existing piles and identifying representative levels of testing. Four key elements of investigation; geometry, integrity, durability and capacity are evaluated. 3. In terms of design this paper supports the adoption of alternative probabilistic methods aligned with communicating to Clients in terms of acceptable ?probability/risk of failure? in place of a factor of safety approach. 4. The project also highlights a number of issues that will require greater attention to maximise the future reuse potential such as foundation load transfer platforms and promoting developments based on early collaborative framework design and contracting across the supply chain.

Jan 1, 2008

By Shoichi Tsukuni, Akihiko Uchida, Kazuo Konishi

"In order to investigate the effect of grid-form deep mixing walls as a countermeasure for liquefaction damage to roads and private houses in Urayasu, Japan, three dynamic centrifuge model tests were conducted. Urayasu is located in the Tokyo Bay area, and private houses in the city incurred severe damage due to liquefaction during the 2011 Tohoku earthquake. In grid-form deep mixing walls design, the distance between grid-form walls is critical to prevent liquefaction. This study clarifies the relationship between the settlement of private houses and the distance between grid-form walls under the conditions that exist in Urayasu.INTRODUCTIONMany private houses in Urayasu, Japan suffered severe damages due to liquefaction during the 2011 Tohoku earthquake (Photograph 1). Fig. 1 shows the location of Urayasu and the maximum acceleration of the observed seismic waves in the Tokyo Bay area. At Urayasu, the duration of the seismic waves (hereafter called the Urayasu Wave) was about 2 min. The maximum acceleration was 1.57 m/s2 (Fig. 2), which is relatively small. The damages occurred in the land reclamation areas that consist of loose sand with an SPT-N value less than 10.To prevent liquefaction in future, it is necessary to adopt suitable countermeasures in the areas where many private houses suffered severe damages. Grid-form deep mixing walls are one such countermeasure. Fig. 3 and Photograph 2 show grid-form deep mixing walls. Walls are constructed using the deep cement mixing method. Fig. 4 shows a plane view of planned grid-form deep mixing walls for roads and existing private houses in Urayasu."

Jan 1, 2015

By A. Rod Kern, Michael A. McNicholas, Yaser Taheri

Deep foundations were required for construction of an 18,000 ft2 (1,672 m2) 4-story office building and an adjacent 23,750 ft2 (2,206 m2) 5-story parking garage in Queens, New York due to an existing uncontrolled fill layer ranging from 15-20 ft (4.6 - 6.1 m) in thickness beneath the building footprint. The geotechnical engineers for the project initially selected auger cast-in-place (ACIP) piles over driven piles to limit the impact of noise and vibrations on the surrounding neighborhood. Ultimately, drilled displacement piles (DDP) were installed since this method offered a more economical solution that would generate the required pile capacity with shorter drill depths and would also mitigate spoils volume. During installation of test piles by the geotechnical contractor retained for the foundation work, multiple unanticipated soil conditions were encountered that would adversely affect the constructability of the piles. The existing fill contained significantly more natural and manmade obstructions than expected and the underlying glacial soil became too dense to penetrate at shallower depths than anticipated. This paper discusses how these issues were overcome through pre-drilling and the use of detailed instrumented test pile data coupled with in-house engineering capability to proactively re-evaluate minimum pile lengths at any given location and keep the project on track. INTRODUCTION Geotechnical work in the New York City market presents soil conditions that can be highly variable and challenging due to the presence of uncontrolled urban fill placed over the native soils. Construction in this area can therefore pose many unforeseen challenges, even with detailed geotechnical analysis being performed at project sites. A case in point is a construction site in Queens, New York. The proposed site development consisted of construction of a 4-story office building with a footprint of 18,000 ft2 (1672 m2) and a stand-alone 5-level parking garage with a footprint of 23,750 ft2 (2206 m2), together with associated new pavements and utilities. The site is bordered by a mix of commercial buildings and residential properties on all sides. Depth of the uncontrolled nature of the fill extended up to 20 ft (6.1 m) below street grade. Given the significant cost associated with removal and replacement, deep foundations were recommended to bypass the unsuitable soils and support the structures at depth where good bearing material existed.

Jan 1, 2019

By Travis Coleman, Elvis Ishimwe

Currently, more than 400 drilled shafts have been constructed by various contractors at the I-90/94 and I-290 Jane Byrne (Circle) Interchange, located near downtown Chicago, Illinois. Cross-Hole Sonic Logging (CSL) and Thermal Integrity Profiling (TIP) tests were performed to evaluate the integrity and concrete quality of the drilled shafts installed at this project. For Phase I of the project the shafts were tested using CSL methods, and the shaft integrity was identified by analyzing the First Arrival Time (FAT) and the signal strength (energy) measurements. For the major portion of Phase II, the Illinois Department of Transportation (IDOT) accepted TIP testing as a substitute for CSL at the request of the contractors. The CSL testing results indicated 54 percent of the tested shafts had anomalies, and 78 percent of these anomalies were located within the lower three diameters of the shafts. To date, TIP testing results indicated the shaft integrity was as expected and acceptable for the all 34 tested shafts. A review of the testing results and a discussion of the detected anomalies are presented. In addition, a comparison of both TIP and CSL measurements is presented in this paper.

By Satyajit Vaidya, Rudolph Frizzi, Sandy Larimer

"This paper presents a case history in design and construction of a deep foundation system that included high-capacity open-ended driven piles constructed to support a high-rise building in Manhattan, New York. The project site is bordered by existing buildings, active streets, and critical public transportation infrastructure, which were considered in the new building’s deep foundation and seismic design. This paper focuses on driven pile foundation design and installation through relatively loose soil deposits. Unique design aspects included seismic design considerations, and pile splice design for open-ended steel pipe piles subject to significant uplift and lateral loading. Unique construction aspects included quality assurance of open-ended steel pipe pile splices, and uplift and lateral load testing of driven piles installed in close proximity to other foundation elements installed for the project.SITE CONDITIONS AND SUBSURFACE CONDITIONSThe project site is located in Manhattan, New York, and is bordered by existing buildings, active streets, and critical public transportation infrastructure that is located about 60 feet from the site. The existing sidewalk grades around the site are between about el 4 and about el 13; elevations are referenced to the North American Vertical Datum 1988 (NAVD88).Subsurface conditions at the site generally consist of successive strata of historic fill, former river bottom deposits consisting of compressible clayey soils, and medium dense to dense sand, overlying mica schist bedrock. A generalized subsurface profile is shown in Fig. 1. The historic fill stratum is about 10 to 45 feet thick, and generally consists of loose to medium dense sandy soils with varying proportions of silt, gravel, and miscellaneous debris such as brick, concrete, and glass fragments. The underlying former river bottom deposit stratum is up to about 15 to 20 feet thick, and generally consists of very soft to very stiff clay and lenses of very loose to loose sand. Medium dense to dense sand was generally observed below the historic fill and former river bottom deposit strata and overlying bedrock. Top of bedrock was generally observed at about 80 to 105 feet (i.e. at about el -75 to el -100), except in the southeastern portion of the site where the top of rock was observed as deep as about 140 feet (i.e., at about el -135). Groundwater levels typically ranged between about el 1.5 and el -0.5."

Jan 1, 2016

By Paul M. Schuman, Alessandro Bertero, Giuliana A. Zelada, Sharon G. Cranston

Many jet grouted columns were recently installed to create a jet grout-treated soil foundation for an earthen embankment used in a large shoreline stabilization project in the Mystic River in Charlestown, MA. A physical test program was used to determine whether the jet grouting parameters the Contractor selected would meet the design requirements given the local soil variability, including soft river sediments and organic soils. The presence of hydrocarbons encountered in the marine sediments during the test program caused concern that the design strength could not be achieved. The published literature discusses the environmental aspects of jet grouting with hydrocarbons. The literature did not include many studies of the effect on jet grout-treated soil strength for the types and concentration of hydrocarbons encountered on this project. The grout mix, air pressure, and number of passes of jet grouting were varied in a second field test program to determine jet grouting parameters needed to achieve the design strength of columns with hydrocarbons. A geo-probe study was performed to identify the type and concentration of hydrocarbons on the site. With few exceptions, the quality control core samples from the production columns met the design requirements with many strength values far exceeding the design strength. This paper presents the data, and reviews the lessons learned. PROJECT BACKGROUND The Charlestown Bus Garage, located in Cambridge, Massachusetts, is a Massachusetts Bay Transportation Authority (MBTA) bus maintenance facility located on the Mystic River. The site was home to a coal gasification facility before it was developed by the MBTA as a bus garage in 1978. A deadman-anchored steel sheet pile bulkhead wall installed along the Mystic river on the east side of the site supports the site grade at about El. 11 ft (NAVD 1988) (Figure 1).

Jan 1, 2019

By Bengt H. Fellenius

An upgrading and straightening of a highway included building a bridge across a small river. A routine site investigation was initiated to determine the conditions for designing the foundation of the bridge. The proposed bridge was a two-lane highway bridge in one span with a total length of 30 m (100 ft), as indicated in Fig. 1. It was to be placed about 20 m (66 ft) upstreams of the bridge for the existing highway. The site investigation included one boring at each abutment with soil sampling and in-situ vane testing and placed about halfway up the slope from the small river at ground surface elevation + 54 m. Within the investigated maximum depth of 40 m (130 ft), the soils at both borehole locations consisted of a thin clay crust over a thick deposit of soft sensitive clay with a natural water content of about 70 % and a liquid limit of about 60. The undrained shear strength below the crust was about 20 KPa (400 psf) and increased slightly with depth. The sensitivity was high, about 40.

Jan 1, 1987

By Ke Yang, Robert Liang

"Drilled shaft foundations are widely used for many types of structures, especially for highway bridges, high rise buildings, and costal structures. The lateral design considerations are crucial for those structures that are subjected to lateral thrust forces, winds, waves, and earthquakes. The p-y analysis is the most widely used method for the analysis and design of drilled shafts for lateral load applications in soils. However, existing p-y criteria were developed based on the lateral load tests on small diameter drilled shafts in soils. Although, a lot of lateral load tests have been conducted, there are a limited number of lateral load tests on large diameter drilled shafts embedded in clay. In this paper, a lateral load test on 2.44 m diameter fully instrumented drilled shafts in clay is presented. The site specific p-y curves are derived based on strain gage readings. The existing p-y curves are found to be much softer than the site specific p-y curves. Correspondingly, the deflection at the top of the test shaft under the maximum applied load is predicted to be eight times larger than the measured value using existing p-y criteria. A new p-y criterion is proposed in this paper. The proposed p-y criterion is proven to be able to capture the site specific p-y curves of the load test and to predict closely the deflections at the top of the test shaft. INTRODUCTIONDrilled shaft foundations are widely used for many types of structures, especially for highway bridges and costal structures. The lateral design considerations are crucial for those structures that are subjected to lateral thrust forces, winds, waves, and earthquakes. Although efforts have been made on studying lateral response of drilled shafts; nevertheless, only limited studies have been published on the behavior of large diameter drilled shafts under lateral loads and the corresponding design methods."

Jan 1, 2005

By Akshay Sakhuja, M. S. Karthika, R. Vignesh

"The bridge across River Mandovi in Goa is a cable stay bridge structure proposed parallel, along existing bridges for regulation and reduction of vehicular traffic; the entire bridge structure is supported on pile foundation socketed in rock. This paper describes drilling related issue encountered during execution of pile where bed rock varies considerably from factual geotechnical investigation, which in turn affected the productivity of bored piles socketed in rock then chiseling is advocated for rock socketing with limited number of blows based on penetration resistance of rock encountered or equivalent energy principle to increase the productivity and also to avoid excess chiseling which otherwise would have fractured the rock mass below and around the pile tip resulting in increased settlement of pile subjected to design load. Contractor decision on socket length have been taken without compromising either quality or productivity; the paper presents various procedures and the equipment involved for installation of pile in rock along with the conclusion related to termination of pile in rock and also the lessons learned in process.INTRODUCTIONPile foundations are generally used to transfer heavy loads in deeper bearing stratum if the soil immediately beneath the base of the foundation does not have sufficient capacity. The bridge across River Mandovi, Goa is in its construction phase as a part of the development plan of Goa State Infrastructure Development Corporation Ltd (GSIDC). The project was awarded to M/s. L&T Construction, Heavy Civil Infrastructure; subsequently the geotechnical investigation was awarded to M/s L&T Geostructures.The client has specified the foundation of the bridge as rock-socketed. Rock socketing is generally done to achieve higher bearing pressure through concrete-rock shear interface which many building codes permit. The design and construction of rock socketed pile foundation entails a detailed analysis and judgement on the superstructure loads, predominant geological conditions as well as ground water levels. The termination of pile is normally based on thumb rule of half to three times the pile diameter into the rock. Quite often the criteria is based on chisel penetration rate (Gandhi,1990) In fact, this is the key factor to consider appropriate and economical depth of embedment of pile into rock stratum which necessitates enormous understanding on the type and quality of rock strata encountered which may significantly influence the selection of suitable rotary rig for pile installation. Such criteria are site specific and also applicable for the set of equipment used for the particular project."

Jan 1, 2015

By Filippo Maria Leoni, Alessandro Bertero, Gianluca Pianezze

"As part of the Southeast Louisiana (SELA) drainage program, designed by the U.S. Army Corps of Engineers (USACE) to reduce flood damages in the City of New Orleans and surrounding parishes through the construction of new pumping stations and better drainage canals, the SELA-22 project entailed the installation of a concrete covered canal along Jefferson Ave. and Prytania Street, in a highly urbanized portion of Uptown New Orleans, LA. The scope of the required soil improvement was to replace the soil between two parallel lines of sheet piles with a soil-cement mass to eliminate underseepage and provide structural support for the concrete culvert. The USACE selected the jet grouting (Jet Grout) technology for the construction of the bottom plug. The bottom plug is between 18 and 21.5 ft thick with a maximum depth of approximately 40 ft, for a total length of approximately one mile. The treated soil comprised soft clays and silts with occasional presence of sands. Project specifications required 100% area coverage, a 28-days unconfined compressive strength of 100 psi and hydraulic conductivity of 1x10-6 cm/s, to be verified by testing specimens from cored samples. The specialty geotechnical contractor proposed to accomplish the task utilizing their proprietary and innovative elliptical bi-fluid Jet Grout technology, and elected to perform a pre-construction bench scale laboratory mixing program to determine the most suitable grout mix features (i.e. binder type and proportions, binder content, etc.) to be applied in the subsequent field test and production stages. This paper will summarize and compare the results obtained from the different pre-construction and construction stages; interpretations of the data will be provided, along with general considerations regarding the effectiveness and significance of bench scale testing for jet grouting applications.INTRODUCTIONIn general, the effectiveness of the construction parameters in any ground improvement work depends largely on the physical and mechanical properties of the soil to be treated. Therefore, well designed laboratory and field test programs, aimed to disclose the interaction between the site-specific soils and the mixing parameters, are essential to achieve the desired end product."

Jan 1, 2016

By Negin Khalili-Motlagh-Kasmaei, Paul O'Leary, Christopher J. Rothsiedl, Dimitar Ninesvski, Alexander Zöhrer, Vincent Winter

This paper presents the implementation of a digital twin for the vibro-replacement ground improvement process, as part of a digital construction site. The goal is to implement an evidence-based quality assurance for each produced element (column or point). The system uses a combination of planning data and real-time machine data collected automatically from construction equipment. In addition to the quality assurance, feedback is provided in a number of areas, e.g., condition monitoring of the equipment. The digital twin builds upon the real-time sensor and machine data, fused with metadata, to implement a digital model for the process. A hierarchical data evaluation, using rule-based Key Performance Indicators (KPIs), permits viewing of the spatial variation of data over the construction site. This permits the modelling of systematic variations in subsurface properties across the site, enabling the detection of anomalous individual elements, the diagnosis of their cause and the prediction of properties as construction proceeds over the site. All time-series data and KPIs are represented by standard classes of objects, leading to a generic coding of the data analysis; this minimizes the effort required to add additional sites and/or new KPIs. Examples are presented for a number of sites, where the system was used to identify anomalous columns.

May 1, 2022

By Gerald Verbeek, David Tara

"When selecting an impact hammer to drive a particular pile, the decision is often based on local experience. In those cases, the contractor falls back on previous experience or draws on the experience of the hammer manufacturer to select the hammer that will be able to do the job. Obviously, a more scientific approach would be to perform a pile driving simulation using one of several commercially available software packages (e.g., GRLWEAP, AllWavePDP or PDPWave).However, this type of analysis requires quite a bit more effort. First, an accurate model of the pile driving process has to be developed, which includes a model of the soil profile at the job site and input into the analysis program. Then, the model must be analyzed to assess whether the combination of hammer, pile and soil model work.Over the years, numerous individuals and organizations have tried to develop something that would fit nicely in between these approaches: something more advanced than a gut feeling yet something that could be done on the back of an envelope; in other words, a “Goldilocks” approach — not too simple, not too complex, but just right.Screening Tool CriteriaThe goals of the approach are twofold: (1) select the appropriate impact hammer to drive an open toe steel pipe or H-pile, and (2) then use the model for the subsequent high strain dynamic testing (HSDT). The Goldilocks approach centers around five different criteria.1. Maximum Driving StressTo minimize the risk of damage, the maximum driving stresses are generally limited to 80 to 90% of the yield stress (fy) of the steel section. This approach does not consider issues such as hammer alignment, initial imperfections, denting and/or elastic buckling, and pile material fatigue history. However, even when these issues are not applicable, limiting average stresses to 0.9fy or even 0.8fy does not necessarily mitigate the risk of pile damage (Mostafa, 2011)."

Jan 1, 2017