Search Documents

By Gerald Verbeek, Erick Baziw

"Downhole Seismic Testing (DST) is an important geotechnical testing technique for site characterization as it provides low strain (<10-5) in-situ interval compression (Vp) and shear (Vs) wave velocity estimates. These velocities are determined by obtaining relative arrival times of source waves as they travel through the stratigraphy and are recorded by one or more vertically offset seismic sensors. A challenging aspect of this process is to characterize the seismic data sets to determine the analysis method that will result in the most accurate interval velocity values. This paper introduces an assessment technique which utilizes linearity estimates (i.e., hodograms fitting straight lines) from the polarization analysis in conjunction with crosscorrelation coefficient calculations of the full waveforms as well as the deviation of the source wave frequency spectrum from a desirable bell-shaped curve. The paper will provide an overview of the technique and include some examples of actual data sets where the technique was applied to analyze those data sets.1. INTRODUCTIONIn general terms, Downhole Seismic Testing (DST) such as Seismic Cone Penetration Testing (SCPT) is a geotechnical technique for measuring in-situ shear and compression wave velocities (VS and VP respectively). The main goal in DST is to obtain arrival times as the source wave travels through the soil profile of interest, and from these arrival times the velocities are then calculated. Figure 1 shows a schematic of the typical DST configuration: a seismic source is used to generate a seismic wave train at the ground surface. One or more downhole seismic receivers are used to record the seismic wave train at predefined depth increments. The downhole receiver(s) may be positioned at selected test depths in a borehole or advanced as part of an instrumentation package as in the case of SCPT. When triggered by the seismic source a data recording system records the response of the downhole receiver(s)."

Jan 1, 2017

By Ahmad Mahboubi

The damage caused by catastrophic earthquakes has always been an incentive towards more sophisticated building codes and requirements. In parallel to computer technology development, the engineers? attitude towards acquisition of more accurate results is increasing. This approach leads to designation of structural elements with more elaboration considering different aspects of their behavior. In addition, less simplified methods will be considered as satisfactory for analyzing such problems. The problem of soil-pile-structure interaction is one of the phenomena that can be included in this category. In general, there are two methods by which the study of soil-pile interaction phenomenon is studied. These include direct and sub-structuring methods. The sub-structuring approach relies on the linear or slightly non-linear behavior of soil since it employs the results of kinematic interaction analyses for inertial interaction studies. In the past, the kinematic interaction between pile-soil was considered as negligible. This was due to the softer nature of the surrounding soil that increased the time period of vibrations. However, more research revealed that although this approach was consistent in many cases, there were some sites where the time period decreased. This was due to the material properties of the foundation and the soil, in a way that caused the frequency of vibration meet natural frequency of the system. The second type of interaction is the inertial interaction which reflects the effect a structure on top exerts on the oscillation experienced by the foundation. This paper examines the impact of vertical load on the inertial interaction by virtue of impedance functions. Three different load cases for the structure at the top of a pile foundation were considered for the analyses conducted in this study. The changes in the stiffness and damping of the system by frequency are studied and finally, the results are presented.

Jan 1, 2010

By Parameswaran V. S, Anshuman Singh

This is a case study on ground improvement using Stone columns at Kokrajhar in Assam which comes under seismic Zone V as per IS: 1893. The strata at site comprised of mostly fine sands with low SPTN values, fine content less than 10% and ground water table (GWT) at shallow depth. As ground water table subjected to seasonal variation, water table is considered at ground level for designing purpose. The geotechnical profile of the boreholes was analysed on the guidelines of IS 1893 (Part 1) -2016 and it was observed that the liquefaction potential of the soil layers is prominent and ground improvement is inevitable up to a depth of 9.5 m below existing ground level. In order to mitigate the liquefaction of soil layer, Stone columns were proposed. The in-situ soil is densified using wet top feed vibroreplacement method with an area replacement ratio of 16%, so that the relative density of the soil can be enhanced to prevent liquefaction risk. Correlation between relative density, fines content and increment of SPT N –value given by Tokimatsu and Yoshimi (1983) was used for designing purpose. Field tests such as SPTs were carried out at site to validate the extent of SPT (N) improvement. Detail comparison of pre and post density, SPT N values and CRR values were discussed in this paper.

Nov 1, 2022

By Giulia M. B., Ferruccio Cribari, Alessandro Bertero, Eliano Romani, Roberto Sorge, Francesca Casini

"The use of Artificial Ground Freezing (AGF) to form earth support and seepage control barrier systems has had applications worldwide. These cover a variety of construction problems, including the formation of frozen earth walls to support deep excavations, structural underpinning for foundation improvement, and temporary control of ground water in construction processes. An application of AGF during construction of Line C of Rome underground is described in detail.The new line “C” of San Giovanni metro station was constructed adjacent to the existing line “A” of San Giovanni station; the new metro line “C” is deeper than line “A” and runs below the existing station. The underpass project envisages an Artificial Ground Freezing in order to create a structural and waterproof temporary cut-off suitable to the two new tunnels excavation, while keeping trains running in the safest possible condition. The excavation of tunnels under the water table, with a hydraulic head of over 10 m in not homogeneous soils having different mechanical properties and permeability and below existing sensitive structures, involves special ground freezing sequences and methods, as well as peculiar drilling systems and operations, such as TDDT (Trevi Directional Drilling Technology).Artifical Ground Freezing IntroductionNatural freezing occurs seasonally in many areas of the globe and can affect negatively the engineering performance of geotechnical structures; on the other hand, man-made freezing is a controllable process that can be used by civil engineers to stabilise temporarily the ground in order to support and/or exclude groundwater from an excavation until the final retaining and lining structures are constructed. Freezing and thawing of the pore fluid within soils involve complex thermal, hydraulic and mechanical processes that have significant mutual interactions. For example, phase changes of the pore fluid caused by temperature variations can modify the pore water pressure in the soil, which, in turn, can induce mechanical deformation. At the same time, any changes in the hydraulic and mechanical conditions affect the thermal processes by advection and changes of ice and water contents.An application of AGF which will be presented in the paper, refers to the construction works of Line C of Rome underground. In this case AGF was carried out to provide temporary support during excavation of the two Line C running tunnels directly underneath the existing S. Giovanni station of Line A, in the safest possible condition. In order to keep the trains of Line A operational during excavation, a temporary structure was installed and a real-time monitoring system was conceived in order to control the temperatures of the soil during freezing and the response of the structures of the existing station."

Jan 1, 2016

By Kevin Kuhl

With the destruction of the US-90 Bridge spanning St. Louis Bay by Hurricane Katrina, the State of Mississippi awarded its first major design-build contract in order to have a completed four-lane bridge in a period of less than two years. The structure consists of 76 pre-cast concrete beam spans with a total bridge length from Bent 1 to Bent 77 of 11,124 ft (2.1 miles). All 77 bents are founded on pre-cast, pre-stressed concrete piles and consist of two foundation types: pile bents and water line footings. A total of 53 pile bents were utilized where the deck is less than 52 ft above the water. Further divided, 10 pile bents, supported by 24 in. square, solid piles, are located on land. The remainder of the pile bents are located within St. Louis Bay and supported by 36 in. square, voided piles. All the waterline footings are supported by 30 in. square, voided piles. In total, 138 -24 in., 437 -30 in., and 463 -36 in. piles support the structure. Production pile design was based upon information gathered from the subsurface investigation, design soil profile and 23 out-of-position test piles. Verification of the design was established by monitoring the first production pile driven at each bent using the Pile Driving Analyzer. Particular challenges included highly variable coastal deposits, loads in excess of 1600 kips per pile and a compressed construction schedule. Initial drive capacity of a portion of the production test piles was less than expected resulting in a minimum 14 day setup. Following the setup period, restrikes were necessary to verify capacity. Project production piles ranging from 50 ft in length to in excess of 160 ft in length were used to achieve the required resistance. This paper includes a brief overview of the foundation design and indicator test pile program. The main objective is to provide a summary of the quality control procedures including establishing the driving criteria for each bent and to present issues that arose during production pile driving and the solutions that followed.

May 11, 2007

By Osama A. Safaqah

Driven plate anchors can be used to hold in place large bridge caissons during floating construction. Their small size and simple method of installation make them a very cost effective alternative to other direct-embedment, gravity, and drag anchors. The geotechnical design of plate anchors involves the anchor geometry, embedment, drivability, and proof testing. This paper describes the experience gained with plate anchors used during construction of the new Tacoma Narrows Bridge. For this project, the anchors had to be driven in dense to very dense sands, and had to resist large forces from 7-9 knot currents.

Jan 1, 2013

By Mohamed Elgouhary, Carol L. Tasillo, Daniel Koziol

"The Bolivar Dam, located near the Village of Bolivar, Ohio is one of a system of dams designed to provide flood control and water conservation in the Muskingum Watershed. The Bolivar Dam is a “dry dam” that only impounds water during flood events. In order to address problematic seepage, which negatively affects the structural stability of the dam, the U.S. Army Corps of Engineers (USACE) designed a partial-depth and partial-length Seepage Barrier Wall (SBW) through the upstream slope of the dam. For this project, TREVIICOS constructed a 36 in (914 mm) positive SBW by plastic concrete panel wall method and excavated using hydromill and clamshell equipment. The plastic concrete was manufactured on-site, which allowed for enhanced quality control and prompt service. This required the installation, commissioning and operation of a concrete batch plant on-site. This paper presents the challenging aspects of the design, manufacture and placement of the plastic concrete for the SBW in order to meet contract strength and permeability requirements as well as workability requirements necessary for tremie concrete placement.Project General InformationBolivar Dam is located in Northeast Ohio (Fig. 1). It is one of a system of sixteen dam projects designed to provide flood control and water conservation in the Muskingum Basin, which covers 20 percent of the State of Ohio (Fig. 2). Bolivar Dam is on Sandy Creek, a tributary of the Tuscarawas River.The Dam has been constructed, operated and maintained by the USACE, for the Muskingum Watershed Conservancy District. Its construction was completed in 1937 and it has been in operation for flood control since 1939.Bolivar Dam is a rolled earth fill dam, with a typical embankment section made of a central impervious core flanked upstream and downstream by a pervious outer shell with downstream rock toe. The embankment has a maximum height of 87 ft (26.5 m) and a crest length of 6,300 ft (1,920 m), and is comprised of the main embankment starting on the left abutment of about 1,500 ft (457 m) heading to the Northeast, followed by the terrace embankment of 4,800 ft (1,463 m) heading to the North. An upstream impervious blanket extends up to 500 ft (152 m) upstream of the dam along the majority of its length. The outlet works are to the left of the embankment, and consist of an intake structure with six gates, followed by two outlet conduits that finish in a stilling basin. To the left of the outlet works is the uncontrolled emergency spillway, which was doubled in width to 540 ft (165 m) in 1989, and excavated material utilized for construction of a stability berm against the upstream face of the main embankment. A concrete parapet wall was also installed along the upstream side of the crest during this work. In 1982, a toe drain, downstream filter berm and line of 35 relief wells were installed. The filter berm was recently extended an additional 200 ft (61.0 m) downstream and granular filters were placed over an approximate 2000 linear ft (610 m) reach of the lower terrace slope. (Fig. 3)."

Jan 1, 2016

By Monica R. Garcia, Antonio Alberto S. Correia, Paulo J. Venda Oliveira

"The aim of this paper is to analyze the creep behavior of a Portuguese soft soil stabilized with binders in one-dimensional conditions, based on oedometer creep tests. The study focuses on the analysis of the effect of the binder content and binder type on the creep behavior of a stabilized soil. The results show that the best binder type for this soil, in terms of creep behavior, is composed of Portland cement and fly ash with a dry weight proportion of 75/25, as this promotes the development of secondary pozzolanic reactions. The results also show the decrease in the secondary compression index with the increment of the binder content, since it promotes an increase in the cementation bonds between soil particles. The general analysis of the results shows a clear dependence on C??and qu, until values of qu of 1500 kPa; after that this relationship is negligible.INTRODUCTIONThe geotechnical structures (such as embankments, dams and buildings) built on organic soils exhibit notable creep deformations, which increase the maintenance and exploitation costs and can even compromise their functioning. To attenuate the creep effects of the soft ground, some improvement techniques are frequently used, such as preloading or reinforcing the soil foundations with vertical rigid inclusions, like concrete piles, stone columns or deep mixing columns (DMCs). However, the installation of DMCs in the soft ground induces (via the arching effect) a transfer of stresses from the soft soil to the DMCs, which causes an increase in the creep settlement on the DMCs (Venda Oliveira et al. 2011).Notwithstanding the fact that the creep behavior of clays has been the object of several studies (Leroueil et al. 1985; Mesri and Castro 1987; among others), the study of the creep behavior of soil-binder admixtures has been practically ignored by the scientific community. The few studies on this theme have revealed that a stabilized soil’s creep behavior is dependent on: the type of binder (Venda Oliveira et al. 2013), the binder content (Correia 2011; Bobet et al. 2011; and Venda Oliveira et al. 2013), the stress level applied during the creep phase (Venda Oliveira et al. 2013), the organic matter content of the natural soil (Venda Oliveira et al. 2012; 2014), and the curing conditions (humidity, vertical stress applied during curing, and curing time) (Correia 2011; Venda Oliveira et al. 2012).The aim of this paper is to contribute to a better understanding of the creep behavior of a soil-binder admixture, by examining the results of oedometer creep tests. The study focuses on the analysis of the effect of the binder content and binder type on the creep behavior of a stabilized soil. Additionally, the creep behavior is correlated with the effective vertical yield stress and the unconfined compressive strength (UCS)."

Jan 1, 2015

By Justin Simmons, Michael Arnold, Bob Faulhaber

"In order to remodel an existing beach resort on the Gulf of Mexico, an existing three story structure, founded on stepped tapered piles, was to be replaced by a ten-story building with service rooms on a daylight basement level, conference rooms on the next levels and up-scale hotel rooms on the upper levels. The new building was founded on augered-cast-in-place (ACIP) piles. The pile caps and the basement required excavations between nine and fifteen feet (three to five meters) below ground surface.BAUER Foundations Corp. (BFC) successfully used Cutter Soil Mixing (CSM) to install the support of excavation walls. This technique allowed for the adjustment of the wall alignment during execution in order to avoid existing and new piles and other underground obstructions. Nearly 1600 – 16-inch (400 mm diameter) ACIP piles were installed to an average depth of 71.5 feet (22m) below ground surface (BGS) by BFC to support the new hotel structure. Initial grout overages in piles were excessively high and ground stability issues were encountered in some pile locations. By identifying specific areas of concern BFC was able to modify the approach to ACIP installation, effectively mitigating the ongoing risks and successfully completed the project.PROJECTMarriott Hotels began the $300 million renovation and upgrade of their Marco Island Marriott Beach Club Hotel in Marco Island, FL to JW Marriott status in May 2015. The renovation included the demolition of a portion of their existing hotel tower, and the construction of a new 10-story hotel tower consisting of 94 new guest rooms and a 10,000 SF (900 m2) ballroom, among other amenities. As is typical with hotel construction, time was of the essence. The schedule was the driving factor of this project as the owner had already booked events in their new ballroom starting in January of 2017.BFC provided the client with a deep foundation package that included the installation of 1562 Augered Cast-In-Place (ACIP) piles supporting the new tower, and the design and construction of approximately 36,500 SF (3,400 m2) of soil-mixed retaining wall for support of excavation (SoE)."

Jan 1, 2017

By Babak Mamaqani, Pirooz Barar

Regional Connector Transit Corridor (RCC) is part of the Los Angeles metro expansion project under construction which adds three new stations into the system. PB&A was responsible for the design of the support of excavation (SOE) systems for two stations, 2nd/Broadway and 2nd/Hope, in RCC. In this paper, challenges and lesson learned from SOE design of 2nd/Broadway station with a main focus on underpinning design are discussed. 2nd/Broadway station required to cut and cover excavation of 500 ft long by almost 100 ft deep, underneath 2nd Street. SOE systems consisting of drilled soldier beams with tiebacks and/or struts. The main challenge in 2nd/Broadway station was to underpin the LA Times building which was partially protruded into the station. A chellenging underpinning system consisted of concrete panels and ground anchors was designed to support the building surcharge and prevent settlement. The underpinning system was designed based on METRO design criteria and the deflection was evaluated by Finite Element Analysis (FEA) program, PLAXIS 2D. A maximum deflection of 0.4 inches was calculated to occur at the top of the underpinning system. Data from settlement and tilt sensors showed minimal movements which aligned with PLAXIS outputs. PROJECT DESCRIPTION The Regional Connector Transit Corridor (RCC) is Los Angeles Metro’s ambitious Light Rail Project. It runs under the City’s main thoroughfares, Flower and 2nd Streets, and when complete will alleviate traffic and parking congestion in downtown Los Angeles. The Regional Connector will connect thousands of residents living in the bedroom communities of the Inland Empire and Long Beach to their jobs Downtown. The rail line will serve 1.9 miles, using the $1.756 Billion budget to construct the underground rail line, including 3 new stations, at 2nd & Hope Street, 2nd & Broadway, and 1st St. & Central Ave (Fig. 1).

Jan 1, 2019

By Henry H. Tayler, Eric Sturel

1 Triton Square was originally a six-storey building with a one-level basement located within a commercial development near Euston, London. It was designed and constructed in the 1990s and the foundation scheme comprised straight shafted London Clay piles arranged singly beneath columns. The scheme added three storeys and a five-storey infill in the central atrium area to increase the building floorplate by 70% and maintained the usability of the basement space. As the loads to support the additional floorplate area were greater than the capacity of the existing foundations, an optimised strengthening scheme of small diameter piles installed within the existing basement and a slender retro-fitted raft was installed to augment the existing piles. The re-use and strengthening of almost all of the existing foundations enabled re-use of a very high proportion of the superstructure and in approximately 35,000 tonnes of concrete and 1,900 tonnes of reinforcement and structural steelwork being re-used. The structural embodied carbon for the refurbished building scheme is estimated at an average of 136 kgCO2e/m2, achieving a Structural Carbon Rating Scheme (SCORS) “A” rating with components detailed in the paper.

May 1, 2022

By Takefumi Takuma, Tsunenobu Nozaki, Masashi Nagano

Using sheet piles and pipe piles for permanent earth retaining is one of the most economical methods for constructing basement walls since they can also work as temporary shoring during construction. A major mixed-use redevelopment project in the UK, encompassing two to three large city blocks, utilized both sheet and pipe pile walls for a two-level subterranean parking structure. The 290m (950ft) x 100m (330ft) basement’s steel walls were designed to temporarily support excavation during construction and eventually to become a load carrying permanent structure in order to expedite the construction process and to achieve cost reduction. Two types of press-in piling machines, one for sheet piles and the other for pipe piles, were used for the job because of their abilities to press in sheet and pipe piles within tight tolerances for finished walls, for difficult installation conditions with very hard soil, and for its very low noise and practically zero-vibration operation; an essential factor for the job in close proximity to other businesses and residents. BACKGROUND Steel sheet pile and pipe piles have been used for many purposes including earth retaining. They are produced at steel mills and spirally welded at a fabrication yard to their corresponding specifications under strict quality control measures. Therefore, they can form highly reliable walls to its design capacity with proper installations. Their advantages as underground walls are:  They can form a high level of water cut-off function with their interlocks sealed by welding or with hydrophilic materials. See Figure 1 for a few examples for a sheet pile application.  They can carry vertical loading in addition to horizontal load and bending moment.  They can be a self-standing and temporary/permanent wall with flexible design and construction processes; bottom-up, top-down or hybrid sequences can be chosen per the project’s needs.  They can form a thinner wall than other wall types, creating larger inner space. See Figure 2.

Jan 1, 2019

By Selvaganesh Selvaraju, Deepak Raj, Sandun N. Wimalasena

One of the world leading oil majors is carrying out a multi-billion-dollar expansion of its integrated manufacturing complex in Jurong Island, Singapore, the global oil trading and refining hub. Soil conditions at the site comprise 10-20m thick reclaimed sand, below which is 3-5m of soft marine clay underlain by stiff soils of the Jurong Formation. The conventional foundation solution would adopt driven precast concrete spun piles; however, precast spun piles have a high embodied carbon from the usage of steel and cement. In order to reduce the carbon footprint, an alternative solution comprising deep vibro techniques was developed. The EFFC-DFI carbon calculator was used to demonstrate the expected scope 1, 2 and 3 carbon emissions for both driven pile and vibro techniques. By using in-house, state-of-the-art fuel-efficient machines, alongside the innovative design concept and usage of natural materials such as sand and stones, actual CO2e emissions were reduced from a potential 21,000 tonnes, with the spun pile’s solution, to only 1,900 tonnes. The saved 20,100 tCO2e is equivalent to an average car driving 2,000x around the Earth’s equator. The paper discusses the application of soil improvement as a more sustainable, lower carbon alternative to conventional piled solutions.

May 1, 2022

By Chu E. Ho, Alfredas Daugiala, Nicola Ebanks

"The construction of an ancillary structure for the new Second Avenue Subway Line in Manhattan, New York City involved a deep excavation in highly variable rock conditions adjacent to a fragile masonry building. The maximum difference between the lowest and highest rock elevations was about 30 feet, which posed a problem for the installation of secant piles that formed the supporting retaining wall for the excavation. At certain areas, the rock levels were higher than the top of the invert slab of the ancillary structure. To avoid disturbance to the adjacent fragile building, the secant piles were fully cased for drilling through the overburden soils and the rock sockets were formed using non-vibratory technique. This paper discusses the design and installation details of the secant pile wall and the contingency measures that were considered to mitigate the highly variable rock conditions. Monitoring of the adjacent fragile building showed that impact of pile installation were controlled within tolerable limits and safety of the building was not compromised.INTRODUCTIONThe 96th Street Station forms part of the newly constructed Second Avenue Subway Line on the East side of Manhattan Island, New York City (Figure 1). During construction of this station, several deep excavations were carried out adjacent to existing fragile buildings (Arksman et al. 2012, Grigson et al. 2016). These fragile buildings were typically four to five stories high, with a single rubble wall basement supported on timber piles or seated directly on the fill. The timber piles were often found to be in a poor condition and connections to the footings were compromised due to rotting of the timber within the zone of water table fluctuation. Several of these fragile buildings had to be strengthened and underpinned to improve the stability of the structures prior to commencement of excavation for the new subway station box (Trabold et al. 2012, Ho and Pena-Iguaran, 2013). The situation was most challenging at Ancillary Buildings 1 and 2 located at 93rd and 97th Street respectively, where secant pile walls were located merely 2 feet away from the adjacent property line, due to architectural space constraints. While mitigation of excavation induced ground movements can be controlled by the adoption of a stiff excavation support system, a more concerning factor was the uncertainty associated with the impact of the secant pile wall installation on the stability of the existing fragile buildings. This was particularly difficult at Ancillary 1 where the secant piles encountered highly variable rock levels that intruded into the excavation space. The following sections discuss the design and installation of the secant pile wall and contingency measures that were considered at Ancillary 1."

Jan 1, 2016

By Jeffrey C. Schuh, Logan Bloemer, Daniel P. Dietzler

Over the past 30 years, the authors have encountered numerous projects where recognizing the geology, soil properties and groundwater conditions, and considering alternative construction techniques have promoted efficient and cost-saving construction. The construction documents for these projects, produced by various engineering firms, provided basic information on geotechnical conditions. The authors became involved in each project either because there was a problem during design or construction or, as a contractor, won the project because they saw a value engineering opportunity to take advantage of the geologic setting of the project to design and build alternatives to what the designer depicted. Understanding the geologic setting is critical before planning and designing begins. Being able to work with the geology and the materials on site is preferred before specifying more costly and complex solutions, which often require the importing of materials and adherence to unnecessary and/or inappropriate specifications. Failing to understand the geology or not knowing all the techniques available for construction can lead designers to develop solutions that could be inappropriate. This paper presents several examples of value engineering and project performance enhancements developed through knowledge of basic soil mechanics and implementing innovative solutions. History and Background Most people attend DFI meetings, present their experiences, listen to others, and read articles and papers with the hope they can learn from others. Geotechnical engineers and contractors often interface with others in the execution of projects who have, at best, a rudimentary knowledge of geology and soil mechanics. Of course, there is a need for architects, bankers, and regulators, etc., but they typically do not have much interest in the nuances of geotechnical engineering, which relies on both art and science. Thus, significant time is spent educating counterparts in the need for comprehensive subsurface investigation programs and the intricacies of construction in the “dirt,” as they typically refer to soil and rock.

Jan 1, 2019

By Kenneth R. Chadwick, Thomas J. Tuozzolo, Terence P. Holman

"Micropiles are often installed to retrofit existing foundations that experience distortion and to underpin structures prior to future construction. The Dublin Road Pump Station project is an example of retrofitting due to a basal failure during construction that compromised the bearing capacity of the soils. A completed pump station settled and had to be restored to its original position, and work could not proceed until a new support system for the partially completed wet well could be designed and installed. The project involved the construction of three below-grade structures for a new pump station in a growing area of Jackson Township, N.J. The general contractor constructed three pump station structures consisting of a pump chamber, wet well and an inlet chamber in early 2006.The geologic conditions beneath the project site (Figure 1) consisted of loose/soft to medium dense/stiff sand, silt and clay to a depth of 40 ft below ground surface, underlain by medium dense to dense glauconitic silty fi ne sand. When the general contractor was constructing the wet well, which involved an internally supported sheet pile excavation 32 ft below the ground surface and 28 ft below the static groundwater level, basal failure, boils and ground loss occurred. Driven piles were installed to support the wet well structure, but additional ground loss was observed within and outside the sheet pile excavation, followed by settlement of the adjacent pump chamber structure. Post-failure investigations were conducted by Mueser Rutledge Consulting Engineers, N.Y. (MRCE), a geotechnical and foundation engineering consultant. Their investigation concluded that the ground losses around the pump station structures had compromised the supportive capabilities of the natural subsoils.The owner engaged Moretrench, a geotechnical specialty contractor, to work with MRCE to develop a constructible solution to support the pump station structures in general and to restore the pump chamber to its original position. Knowing that ground loss had already occurred as a function of the initial basal heave and subsequent pile driving, the team selected micropiles as the preferred foundation element, primarily due to their flexibility in bypassing these disturbed zones and generating capacity as a function of grouting volume and pressure. Drilled piles were also recommended due to concerns about causing additional settlement of the pump chamber if driven piles were used."

Jan 1, 2008

By Brandon M. Robinson, Osman F. Besler, Dominik Gaechter

The Sandbukta-Moss-Såstad (SMS) project is a part of the Intercity development project, which is part of the largest transport project in Norway, consisting of 270 km of new double-track rail. The SMS project consists of 10km of double-track railway including three open stretches and two tunnels. Soil conditions consist of quick clay underlain by Bedrock. Dry soil mixing (DSM) was considered as the main soil improvement method to allow for excavation of the quick clay and construction of the D-Wall panels. The preliminary design revealed around 25,000 ton of binder installation. Therefore, a test field has been conducted to evaluate binder alternatives in means of improved soil strength by considering CO2 emissions. Multicem and Standard cement (Standard FA) have been compared for that purpose. Multicem is a type of binder which mainly consists of Portland cement and cement kiln dust (CKD). CKD is a fined-grained, solid, highly alkaline material removed from the cement kiln exhaust gases. reverse column penetration test (FOPS) and pre-drilled column penetration test (FKPS), which are common tests to evaluate DSM strength have revealed comparable strength outcome for both binder types. Therefore, Multicem has been selected as the main binder type to be used further which provided a reduction in CO2 footprint of up to 40%.

May 1, 2022

By Terence Ma, Seok hyeon Chai, Jeff Lam, Thamer Yacoub, Brigid Cami, Sina Javankhoshdel

The Limit Equilibrium (LE) analysis of pile-supported geotechnical structures normally assumes a constant shear force for the pile instead of considering the non-linear capacity of the pile which is related to the pile displacement. In this study, a 3D Limit Equilibrium analysis is carried out for a landslide model supported with piles by considering the constant and non-linear capacity of the pile which is computed using a separate Finite Element (FE) algorithm. The depth of the pile, soil layering, and the pile properties are used with an assumed maximum displacement to compute the geotechnical non-linear capacity of the pile. In this study, the results of the initial unreinforced 3D LE model was first compared to the 3D FE analysis results. Then, the pile pattern was applied to the failure region in the 3D LE model, and then the factor of safety was recomputed. The results of the constant shear piles were compared to the model with the non-linear piles.

Sep 8, 2021

By Amr Sallam, Ahmad Mohamed, Mohamed Alrowaimi

Renewable energy, in the form of wind and solar, has emerged as main source of energy in the modern society. The wind industry has substantially grown over the last two decades to become a key player in providing energy to public. Wind turbines are getting larger, taller, and more efficient every year. The foundation is a major component of the wind turbine system. The wind turbine foundation must provide short and long-term stability for the overall turbine to allow continuous and safe turbine operation for energy production. The turbine serviceability and stability requirements must be geotechnically and structurally satisfied. In North America, major foundation types currently utilized in the wind industry include gravity spread foundation, mono pier foundation, and pile foundation. In this case study, a Post Tensioned Pile Cap (PTPC) foundation was used to support a 3.15-3.4 Megawatt turbine with 125M Rotor supported on 87.5M-hub-height tower. Soil anchors in the form of Auger-Pressure-Grouted-Displacement (APGD) piles and Continuous Flight Auger (CFA) piles were utilized. Four distinct subsoil conditions were identified, and for which four pile designs were adapted. Due to the occasional encounter of stronger soils at 50 to 55 feet (15.2 to 16.7 m), shorter pile design was preferred. To satisfy the design uplift load, pile post grouting were utilized to increase the shaft capacity of the piles. In this paper, the pre-production pile load test program will be described. The pile load test procedure, analysis, and results will be presented. A discussion will be provided, which led to the selection of the optimum pile design to support the high tension loads taking into consideration pile length limitations.

By Stefan Swartling, Rudy Lyon, Donald A. Bruce

"Since their first production application in Sweden in 1995, water-powered, down-thehole hammers (WDTH) have been used throughout the world in many different drilling applications, total lines, over 25 million lineal meters of drill hole. This paper reviews the history and principles of down-the-hole drilling (DTH) in general with both air and water, before focusing on the details of WDTH hammers. A summary of the numerous and considerable advantages of WDTH drilling is provided, with particular emphasis on their superior productivity, smaller deviation, applicability in sensitive/urban conditions, environmental protection and much reduced energy requirements.HISTORICAL PERSPECTIVE ON PRODUCTION DRILLING METHODSAir-flushed drilling with top hammers began in the mining industry in Sweden in 1873, while down-the-hole (DTH) drills, again with air flush (and activation) became operational in 1950. During that same time interval, Simon Ingersoll had patented the first steam-powered, top hammer rock drill to provide higher productivity in blast hole drilling. It is well known that water, as an activating, flushing and cooling medium, has many significant advantages over the use of air. However, it was not until 1973 that top hammer systems (either air or hydraulically activated) for larger rigs were adapted to the use of water flush, typically via “under the head” swivels.The concept of a water-powered, down-the-hammer (WDTH) had been explored prior to G. Drill acquiring the original patent from Atlas Copco in 1988. LKAB, a huge underground mining company owned by the Swedish Government and providing about 90% of the European Union’s iron ore, purchased G. Drill in 1991 and encouraged the commercial development of the WDTH. The first full-scale WDTH production works were carried out for LKAB in 1995, since when over 25 million lineal meters of drilling have been recorded in both underground and surface applications.In 2001, G-Drill was renamed Wassara, which today still holds the worldwide patents for WDTH technology. Regarding North American usage, the first significant application was by Advanced Construction Techniques (ACT) Ltd. during the test grouting program conducted for the U.S. Army Corps of Engineers at McCook Reservoir, Chicago, in 2002. Since then, WDTH has become the tool of choice for specialty drilling and grouting contractors on dams and other major structures throughout the U.S."

Jan 1, 2015