Search Documents

By Yogesh Prashar

Three conventional uplift tests and 12 Rapid Pile Load Tests (RLT) were performed on total of fifteen 16-inch square pre-cast concrete driven piles at a test site in Emeryville California in December of 2000. The uplift tests were performed in accordance with ASTM standards, and the RLTs were performed using a FUNDEX RLT. The RLT is carried out by dropping a mass of 25-tons on top of the pile, thereby inducing a force that is measured by a load cell. An optical lens records the vertical deflection of LED's that are mounted on the pile. Ultimate uplift and compression capacities of each of the fifteen piles were determined using the Davisson method. Soil parameters were calibrated by back-calculation (cohesion and internal angle of friction) using both the results of conventional uplift load versus deflection curve, as well as the results of the triaxial compression tests. A two-dimensional finite difference model including soil elements, and structural elements representing the test pile was setup using the computer program Fast Lagrangian Analysis of Continua (FLAC). FLAC was used to simulate both the uplift as well as the RLT. Strength increase of cohesive material was also accounted for in the analysis. Numerically simulated and theoretically computed pile capacity curves and axial deformation variation with applied load curves are in close agreement to the observed curve during the field test. Conclusions are made from this test site regarding the factors influencing results of RLT.

Jan 1, 2002

By Clyde Baker

Drilled shafts for many situations offer an economical alternative to driven piles. The Federal Highway Administration (FHWA) has spent considerable time and money in research and developing design and construction guidelines for drilled shafts. However, the full potential of the technology may not be realized because of the uncertainty of the effects of construction on the actual service behavior and the lack of either reliable quality control tests to check for or evaluate defects, or inexpensive load test procedures. Static load testing is very expensive and it is not feasible to load test each shaft on a project. Therefore, other means are necessary to confirm or evaluate the integrity of the completed drilled shaft or to determine the capacity of the completed shaft.

Jan 1, 1989

A technical exhibition was held in conjunction with the 4th DFI International Conference on Piling and Deep Foundations, Stresa. The exhibition was located in the ground floor of the Conference Hall. It was open from 15.30 on Monday April 8 till 16.30 Thursday April 11, 1991. The following is an alphabetical list of firms who took part. 1) A.P. VAN DEN BERG MACHINENFABRIEK B.V. P.O. BOX 68 8440 AB HEERENVEEN The Netherlands Tel: +31 5130 31355 Fax: +31 5130 31212 Stand Executive: A. Duyfjies

Jan 1, 1994

By Edwin W. Meyer

The augered cast-in-place piling technique was used to install deep foundations 20 feet into weathered sandstone. The project involved the upgrading of the Air Quality Control System (AQCS) for a 560 megawatt coal fired power plant located in Stillwater, Minnesota. The site subsurface consisted of 20 feet of overburden overlying weak sandstone. The overburden consisted of sands and gravels with cobbles and boulders, and variable thicknesses of peat. Ground-water at the site was approximately 8 feet deep. Two foot diameter piers were selected to facilitate installation through the cobbles and boulders in the over-burden and to penetrate the sandstone 22 feet. During installation of the first pier, the weak sandstone broke down to sand-sized material that could not be cleaned from the pier hole without the use of slurry to hold the material in suspension. However, the use of slurry would significantly impact both schedule and cost. Since the sandstone could be easily drilled with the pier equipment, it was believed that 2 foot diameter deep foundations could be installed as designed using augered cast-in-place piling techniques. A brief test drilling pro-gram was conducted to evaluate the viability of 2 foot diameter continuous flight augers penetrating 22 feet into the weak sandstone. The test drilling indicated that augered cast-in-place installation techniques should be successful. Following a short delay to mobilize the additional required equipment, construction commenced. Installation of the 2 foot diameter augered cast-in-place piling to a depth of 22 feet into the weak sandstone was successfully performed.

Jan 1, 2006

By Graeme McWhirter

This paper discusses the Installation of a Vibwall for the Cardiff Bay Barrage Project Wales, UK, by Kvaerner Cementation Foundations. Only the second use of the technique in the UK the wall was successfully placed to a depth in excess of 20 metres, in unique and challenging conditions. The installation of the Vibwall was a technical success, but not a financial one. The use of the technique was at its "limits" and this paper recommends some of the controls essential in the carrying out of such work in the future.

Jan 1, 2000

By Alexander Nikolic

The paper presents the foundation design and construction of a landmark urban redevelopment scheme in central London, UK. The scheme comprises the new Tottenham Court Road Underground station, Crossrail interchange box and associated over-site commercial development. The paper focuses on the design, procurement and construction of large diameter bored piles, up to 68m in depth, which form the foundation support system for the over-site commercial development at Denmark Place. The congestion below ground required an intricate foundation design solution which has been a catalyst for developing innovative load transfer arrangements and has resulted in the advancement of pile construction technology in the UK. The foundation system was also designed to cater for the construction of two significant elements of proposed below ground infrastructure. Selected large diameter piles have been constructed within 1.1m of live underground railway tunnels. An innovative D-shaped pile was constructed in a zone subject to particular spatial constraints. The proposed Crossrail tunnels will be bored within 1m of selected over-site development piles. In addition, a 30m deep excavation forming a new escalator box will be constructed in direct contact with the over-site development piles. The stakeholder engagement process is described together with the foundation design development and buildability assessment. The benefits from early collaboration between the designers and specialist contractors are highlighted. From an analytical design perspective, the entire foundation construction sequence was modelled in detail in order to assess the soil structure interaction and any potential adverse effects on existing elements of underground infrastructure. The results from the three dimensional numerical modelling simulation are compared with field monitoring data.

Jan 1, 2011

By David S. Yang

The construction of Oakland Airport Roadway Project for the airport expansion requires stabilization of subsurface soils for the construction of three grade separation structures at two roadway interchanges and the intersection of a roadway and taxiway serving the airport. Loose sandy fills and soft Bay Mud were improved by Cement Deep Soil Mixing (CDSM) for the construction of a soil-cement foundation under the MSE (Mechanically Stabilized Earth) walls of a roadway overcrossing and a soil-cement gravity retaining wall to maintain stability of a roadway undercrossing during and after a major earthquake. CDSM was also used to construct two cutoff walls for groundwater control. A test section was carried out prior to full production to verify that the CDSM equipment, installation procedures, and mix designs could produce the soil-cement with required strength, uniformity, and permeability to meet the design intent. Additional test sections were performed for the confirmation or modification of the mix design and installation procedure to cope with the complex subsurface conditions resulting from the historical development of the site. The test section revealed that the CDSM cutoff walls, retaining wall, and foundation improvements could be constructed to satisfy the design requirements and that the intermittent test sections alleviate the impact of the varying subsurface conditions. Based on the data obtained from the test sections, one CDSM cutoff wall was completed in July 2000. Full production of the CDSM retaining wall, cutoff wall, and foundation began in March 2001 and is expected to be complete in November 2001.

Jan 1, 2001

By Anthony H. Tawil

Modern, high-speed machines used in the manufacture of paper require foundations with stringent settlement constraints. To fulfill this requirement, caisson piles, extending into bedrock, were selected to support a paper machine in Baie Comeau for the Quebec North Shore Paper Company (QNSPCo.). This was the fourth machine in an existing paper mill, and its construction was part of an expansion program which included the building of associated structures such as a wood room and chip storage building, and other facilities, Figure 1. The paper mill in Baie Comeau, Quebec, is located in an area which has extensive deposits of sensitive marine clay which are transformed into a viscous liquid when disturbed by external forces such as the driving of piles. Loss of ground and soil disturbance as affected by piling activity assumed considerable importance in the design and construction of the caissons particularly in view of the proximity of existing plant facilities, including another paper machine.

Jan 1, 1987

By Eric M. Klein

As part of the Woodrow Wilson Replacement Bridge project several damaged wetland and environmental areas were to be mitigated. One of the mitigation projects consisted of constructing a Denil fish ladder around Peirce Mill Dam in Rock Creek National Park, Washington, D.C. The dam is a historic structure operated by the National Park Service. The fish ladder is located between the east abutment of the dam and Beach Drive, a major collector road. Construction of the fish ladder required removal of a portion of the east abutment and an excavation that extended about 22-ft below the pavement of Beach Ave. It was not possible to close Beach Drive except for very brief intervals or at night; therefore, a support of excavation system that would minimize disruption to the public was required. The high groundwater required that the groundwater be cut off prior to excavation; the random rubble and soil fill, and shallow but erratic rock surface precluded driving sheet piling. A jet grout system was selected because the grout probe could penetrate the rubble fill, stabilize a variety of soil conditions, and cut off the ground water prior to excavation. It was not possible to construct a stable wall without tiebacks or soil nails. Given the schedule and tight working conditions it was decided that soil nails through the jet grout wall facing would be the most cost effective method, as it did not reduce the working space as rakers would and would be more cost effective than prestressed tiebacks.

Jan 1, 2006

By Sivilay Sayavong, David Puller, Julian Gatward, David Hard, Martin Stanley

"AbstractThe Thames Water Tideway Tunnels programme involves the upgrade of London’s combined sewer and storm water system. The first section is the Lee Tunnel between the Beckton Sewage Treatment Works (STW) and the Abbey Mills Pumping Station. This will intercept the overflows currently discharging to the River Lee and has the capacity to store and transfer 350,000m3 of storm water and sewage. The project required 4 shafts and a 6.9km 7.2m diameter tunnel. The shafts are some of the largest ever constructed in the UK, with diaphragm walls up to 98m deep and 1800mm thick. As a result of the innovative methods of diaphragm wall design and construction adopted the 4 very large and deep shafts were able to be excavated and completed safely, with minimal water ingress and with extremely high quality.MVB, a joint venture of Morgan Sindall, Vinci Construction Grands Projets and Bachy Soletanche are delivering the £635m contract with Thames Water’s Project Management Team in a collaborative manner under an NEC contract. Mott MacDonald, Morgan Sindall UnPS & Bachy Soletanche are acting as designers.Some of the important advances in diaphragm walling made included:??Diaphragm wall design to both EC2 & EC7 taking into considering the assessment of chalk stiffness, high hoop stresses, large multiple openings and non-axisymmetric loadings.??Formation of shafts as a faceted circle from a series of overlapping panels, with primary panels up to 7.2m wide demanding concrete volumes up to 1300m3 be poured in one go. Overlapping secondary single bite panels cut into the grade C50/60 concrete.??Excavation of the full geological stratigraphy of London making bentonite management complex.??Panel verticality of 1:300 required over the full depth. The results achieved this and in many cases exceeded expectations with some panels coming in at up to 1 in 800 with the majority at 1 in 400 to 1 in 500. The project is also the first in the Soletanche Bachy Group to take data from the ultrasonic drilling monitor used to check the verticalty in electronic format in order to create 3D CAD as-built drawings.??Each diaphragm wall panel was reinforced over its full depth. Up to 18 separate pieces of reinforcing cage had to be installed in primary panels. Cages underwent a full range of temporary works designs to check that lifting, splicing and placing could all be undertaken safely. Fibreglass was used in the tunnel portals in the shafts to ease breakthroughs."

Jan 1, 2014

By Donald A. Bruce

The construction of major structures in karstic limestone terrains poses difficult problems to designer and contractor alike. This reflects the inherent variability of such conditions, and also the significant impacts caused by the construction processes themselves. Three case histories are provided of recent projects in the United States: the sealing of a major inflow into a quarry, the improvement of a highly loaded bridge pier foundation, and the installation of high capacity micropiles. Emphasis is placed on problem assessment and execution verification.

Jan 1, 2002

By Christopher M. Kenney

Augered-cast-in-place (ACIP) piles have been utilized on commercial projects throughout many parts of the country for years, but are only beginning to be scrutinized for use on major infrastructure projects and other critical structures in some regions. Numerous engineers are aware that ACIP piles are an economical foundation alternative, and many technical papers have been presented that provide reliable methods of estimating ACIP pile load capacity. However, designers may not yet appreciate that the load-settlement behavior of ACIP piles is very similar to that of drilled shafts. This paper analyzes ACIP pile case histories from throughout the country and demonstrates that ACIP pile settlement under applied load is consistent, predictable, and very similar to the documented behavior of drilled shafts. This paper also presents a simple but accurate method of estimating ACIP pile settlement at the design load, and illustrates the need to estimate the equivalent diameter of the as-built ACIP pile when estimating pile behavior. Finally, this paper presents back-calculated values of the drained elastic modulus from the ACIP pile case histories that may be useful to those using more sophisticated methods of estimating ACIP pile settlement.

Jan 1, 2001

By Jean-Pierre Hamelin

Ground movements induced by underground excavation are always of critical concern, particularly in urban areas. Compensation grouting now appears as a safe means to control these movements. The paper presents new advanced systems developed by the specialist contractor to bring, at all stages of the project, an efficient control of operations and presents a case history taken from the project at Tren Urbano, Rio Piedras Section, constructed beneath an historic commercial section of San Juan de Puerto Rico.

Jan 1, 2000

By Charles Pol Vuillier

Piling work for modification to the Charles Grimes Bridge in Melbourne, Australia required piles to be installed through 15 to 20 m thickness of very soft to soft silty clay overlying 10 m of stiff clays and sands in turn overlying siltstone. The presence of an old sewer founded at depth in the soft clays demanded that vibrations be kept to a minimum. Two pile type were used by Vibro-pile (Australia) to provide the client with the most economical piling price. The two pile types were CFA piles of 750mm diameter founded in the weathered rock and a full displacement concrete injected screw pile developed by Vibro-pile called the "Z" pile, founded on the rock. The development and features of the "Z" pile are briefly discussed, including the perceived applications and advantages of the pile type. On board instrumentation comprising a computer was used to monitor all aspects of the construction. The rig instrumentation provided an important quality control measure that gave confidence in the pile installed. Pile performance was proved on the cast in situ piles by dynamic load testing methods. Initially tests performed with a 120 kN drop hammer, which was not capable of mobilising the required loads. The performance was then satisfactorily proved by using a drop hammer of 20 tonne mass delivering blows drop heights of 1.5m. Low strain integrity tests on a number of piles were also used to confirm the structural integrity of the piles.

Jan 1, 2000

By Tatsunori Matsumoto

In order to investigate the variation of the load-displacement relations of piles in a site, vertical load tests were carried out on 25 small diameter steel pipe piles. Out of 25 piles, 15 piles were close-ended pipe piles attached with a blade at the pile toe and 10 piles were open-ended pipe piles. To carry out these load tests in a short period, two types of rapid load test methods, Spring hammer load test and Falling mass load test, were employed. The load tests of all piles were completed in two days with 180 blows in total. In order to estimate a static load-displacement of a pile, non-linear damping method was used. It is shown from the test results that the performance of the pipe piles such as the ultimate pile resistance and the initial pile head stiffness is improved by re-driving.

Jan 1, 2006

By S. D. Zhang

The first reinforced earth railway bridge abutment in China has been successfully constructed of September, 1985 under the supervision of the Reinforced Earth Researth Group of Shanghai Institute of Railway Technology. In order to verify the reliability of the designed structure and its behaviuors, the 1:10 reduced scale model tests in laboratory and field tests on the actual structure during construction were proceeded. Various loads of different positions were charged, the vertical and lateral earth pressure in the filling soil, the stresses developed in the reinforcements, and the deformations of the models or the actual structure were recorded in those tests. The behaviors recorded are presented and discussed in this paper.

Jan 1, 2010

By Tobias Hansson

The quality of Lime Cement (L/C) columns is to a great extent dependent on the installation procedure. At a site in the south of Sweden, the client reported problems with the installed columns. To evaluate the operator and equipment dependent part of the installation, Hercules Grundläggning AB was appointed as a competitor to the site contractor. The purpose was to install a number of L/C columns with equal installation parameters for both contractors. A total of 65 test columns were installed in June 1999. The geology is a typical Swedish organic soil profile with a top layer of peat overlying gyttja and clay. Two different binders were used in the comparison; blast furnace slag with cement and lime with cement. After installation, the quality of the columns was monitored by penetration tests and a column sampler for extracting whole columns. The column penetration test were performed 28 and 134 days after installation and extraction 134 days after installation. Inspection and tests of the extracted columns showed that by using a fully computer controlled procedure, the contractor produces columns of superior quality and homogeneity.

Jan 1, 2000

By R. A. Bullivant

Roger Bullivant Piling Limited has started 1992 with the introduction of the CONE PILE into its range of precast concrete foundation techniques. Since the establishment of its Piling Division ten years ago, alongside the original Underpinning Company, a commitment to innovated development has seen a steady growth in Roger Bullivant's activity in piling, ground treatment and general foundation engineering. Over the last four years, £1.2 million has been invested by the Bullivant Piling Division into research and development in the field of precast piling and other foundation systems. The goal has been to develop economically attractive systems tailored to our clients design requirements and, wherever possible, unique to Roger Bullivant Piling.

Jan 1, 1992

By Aly M. Mohammad

State and federal agencies during rehabilitation of existing bridges may require the existing bridges to be evaluated under seismic conditions. If the bridge does not perform under the seismic event, the bridge may require seismic retrofitting. Bridges are classified as: Critical, Essential, and Others according to their importance. Geotechnical considerations play a major role in evaluating the bridge behavior under a seismic event. Subsurface conditions influence the magnitude of ground acceleration and hence the forces and moments on the superstructure. This paper will provide a detailed description of the geotechnical aspects associated with the seismic retrofit evaluation for the 12th Street and 14th Street Viaducts located in Jersey City, New Jersey. The paper will also present a description of the geotechnical investigation program including seismic cross-hole surveys to determine the dynamic soil parameters, including the results of site-specific response spectra for both the 475 and 2475-year events. Liquefaction assessment methodology utilizing an equivalent factor of safety will also be described and the design method used will be summarized. In general, the pile foundation is modeled as 6x6 foundation stiffness matrix with 36 stiffness coefficients at the center of the pile cap. The seismic loading on the foundation is evaluated in a pseudo-static analysis, where the dynamic earthquake-induced loads are presented by static forces and moments. The computer program FB Pier was used to evaluate the foundation stiffness. The moments, axial loads, and shear are input into the FB Pier model. The stiffness of the foundation is determined and the results are then input into the Structural model to determine new forces and displacements. Adjustments are made until the loads are compatible with the stiffness used. The understanding of the geotechnical conditions at the 12th Street and 14th Street Viaducts and the coordination between the Bridge and Geotechnical Engineers were able to provide significant cost saving to the Owner. The Design Engineers were able to retrofit the existing Viaduct foundations with reasonable number of additional piles. It is believed that the results and finding presented in this paper will benefit both the Bridge Engineers and Geotechnical Engineers by highlighting the importance of interaction between the two disciplines.

Jan 1, 2006

By Donald A. Bruce

"Abstract The Deep Mixing Methods (DMM), in their current forms, have been employed in the United States since 1986, although an earlier version had seen service from 1954. The earlier developments were strongly influenced by practices in the Nordic countries and Japan, while by the late 1980’s several DMM systems had been developed in the U.S. itself. Since then, DMM has continued its evolution, principally via the challenges of a series of large, landmark projects, but also via distinct, significant technological advances. This paper highlights the key points in the history of DMM in the U.S., and provides an overview of the different methods currently in use.In the BeginningIt is a common misconception that the history of applications of the Deep Mixing Methods (DMM) in the United States dates from 1986 when SMW Seiko Inc. — a subsidiary of Japan’s Seiko Kogyo Company — was established in the Bay Area. However, the author believes that Intrusion Prepakt Co.’s patented MIP (Mixed in Place) system had been used, albeit sporadically (about 30 projects are recorded), since 1954 (FHWA 2000, 2001). Ironically, by 1961 this single auger method had been extensively used under license in Japan for excavation support and groundwater control — by the Seiko Kogyo Company. By 1972, the original MIP technique had been succeeded by more advanced Japanese methods, involving multiple augers. Intrusion Prepakt have long since become defunct.The first systematic studies of contemporary Deep Mixing Methods in Japan began in 1967 when the Port and Harbor Research Institute of the Ministry of Transportation began laboratory testing using granular and powdered lime for treating soft marine soils. Fundamental studies continued through the early 1970’s, by which time the development of industrial scale equipment was well advanced, having its first application on a marine trial near Haneda Airport. Coincidentally, laboratory and field research also began in 1967 in Sweden (“Swedish Lime Column Method”) for treating soft clays using unslaked lime. Reportedly the progenitor was a Norwegian, Kjeld Paus, who had made observations on fluid lime columns in the U.S. It would seem that developments in Japan and the Nordic countries proceeded independently until 1975 when the technology leaders from each group (Broms and Boman; and Okumura and Terashi, respectively) presented their — very similar — findings at a conference in Bangalore, India. Limited technical exchanges ensued thereafter.Whereas the Nordic developments continued to focus on the use of dry reagents (cement and lime) and relatively light equipment compatible with operating on and in very soft clays and organics, the Japanese progressed into the use of fluid reagents (cement-based grouts) and heavier equipment for both marine and land-based projects. Thus, by 1986, there were a large number of proprietary (wet and dry) DMM systems in Japan, and a rapidly growing market already by then accounting for over 12,000,000 m3 of ground treatment."

Jan 1, 2014