Search Documents

By T. Jason Hardell

The Victory Bridge project was contracted by the New Jersey Department of Transportation. The project included the construction of two 4000-ft precast segmental concrete bridges to replace the existing Victory Bridge that was built in the 1920's. The existing bridge was a swing span bridge that was in desperate need of replacement. The project was considered high priority due to the large maintenance costs to keep the swing span operating over the busy navigational channel. In March of 2003 construction began on the first bridge and by April of 2005 all of the segments were set for the second bridge. On September 5 of 2005 the second bridge was open to traffic. The total cost of the project was $110-million. The two new bridges required the construction of 24-eight foot and 32-six foot diameter-drilled shafts with rock sockets. All of the shafts were constructed in the tidal Raritan River working from barges. What will follow is a description of the construction techniques that were used to build these drilled shafts, the anticipated and unanticipated challenges that were encountered during the project, and the lessons learned.

Jan 1, 2005

By Han Xuanjiang

Through whole analysis of static testing piles information of a teaching building, this paper put for ward that when the ratioes of unload rebound amount to residual deformation and to total settlement reach the maximum, the testing load is selected as allowable capacity of single pile by camparing with the settlement in the practical engineering, it is proved that this method fits to practice, for other several projects, its also available. Therefore non-destructive testing pile method was improved, so all the tested piles can be reused as engineering piles.

Jan 1, 1991

By K. Y. C. Chung

A case study on foundation engineering through organic soils is presented. Located along the west shore of the Hudson River, site soils consist of random brick fill over a thick layer of peat and organic silts or clays. The organic layer is underlain by medium dense to dense sand with varying amounts of silt. Strong artesian pressures were measured in the sand. A pile foundation system was selected to support all structures. To avoid periodic flooding, new fill must be placed on the existing fill. Large total and differential settlements will occur due to consolidation and secondary compression of the organic soils. This settlement will reduce the allowable pile capacity due to the large negative skin friction in the organic layer; and will necessitate long-term maintenance of the final grade elevation. Pile load tests were performed to determine the allowable compression and uplift capacities, long-term capacities and pile driving criteria.

Jan 1, 2010

By Benoit Virollet

Over the last 10 years the diameter of unbraced, unlined and unanchored circular shafts has grown dramatically in many parts of the world. This progress has taken place through improvements in: construction methods; concrete rheology; and design capabilities. Excavation equipment has become more precise in terms of operator control and ability to correct alignment of digging elements leading to better alignment tolerances. Also contributing to the increases in shaft diameters is the evolution of design models. A better understanding of soil structure interaction is being incorporated into the analyses in terms of radial soil stresses and imposed loads on the shaft. This paper provides an overview of the recent progress made in circular shaft construction, the primary design considerations, and some innovative uses of efficient arc elements to develop unsupported structures of other shapes. In addition, a summary of recent circular shafts constructed worldwide is provided.

Jan 1, 2006

By D. Arentsen

Changing environmental laws, new operating requirements and the increasing accuracy with which the bearing capacity of driven piles can be calculated have all led to the development of hydraulic piling hammers, some very primitive, others very advanced. Users find it difficult to decide which model is the most suitable, because the specifications are neither uniform nor unamiguous. There are no standard specifications and, moreover, the majority of hammers are suitable only for a limited range of applications. For the user, however, it is important to choose a hammer which will meet future as well as current requirements and will not quickly become obsolete or be unsuitable for a particular job.

Jan 1, 1987

By H. Meseck

Dynamic pile test methods to establish the bearing capacity of driven piles were developed in the USA more than 20 years ago. In the Federal Republic of Germany, the first dynamic pile tests were carried out at the end of the 70's. Today dynamic pile tests are successfully used to establish the integrity and bearing capacity of driven and bored piles. The Institute of Foundation Engineering and Soil Mechanics at the Technical University of Braunschweig has developed its own method of measuring and evaluation for the execution of dynamic pile tests. The principles of the dynamic pile tests, the measuring and evaluation plant as well as the experience gained with it in the examination of cast-in-place piles are presented in this contribution.

Jan 1, 2010

By T. Iwanowski

Stress wave measurements and calculations are often used to make a safe determination of the bearing capacity and the integrity of driven piles. Some applications to the restoration of old buildings in the Old Town of Stockholm are referred to and especially analyses of measurements combined with simulations are discussed here.

Jan 1, 1991

By Roy H. Borde

The design of foundations to support overhead signs is primarily based on providing adequate resistance against horizontal wind loads. The typically used subgrade reaction model for the load-deflection analysis of laterally loaded piles and shafts has been found to underpredict the capacity of shafts with length to diameter ratios less than five. The general applicability of an improved model incorporating the influence of shear and moment resistance at the shaft base is demonstrated. The detrimental effect of ground surface slope angle on the ultimate capacity is discussed, and a design chart for estimating the magnitude of the reduction in capacity is presented. A comparison between the predicted and measured responses of nine full-scale load tests performed within this study and sixteen external tests is presented. The models described are implemented in the computer program "LTBASE".

Jan 1, 1988

By Jim Steding

L.G. Barcus and Sons, Inc. recently completed a three-phase project for the expansion of Presbyterian Hospital in Albuquerque, New Mexico for McCarthy Construction Co., the Construction Manager for the project. It was a challenge that allowed Barcus to demonstrate many of it's strengths. Safety of people and property, restricted access, low headroom conditions, extensive planning to maintain hospital operations and a tight schedule were all key elements affecting the successful installation of the Augered Cast-In-Place Piles. Phase I began with installing and performing a 450-ton pile load test on an 18-inch diameter Augerpile 65 ft long. The load test was installed and performed directly in front of the Emergency Room entrance. Space was limited and the E.R. had to remain open with uninterrupted ambulance access. The results of the load test were outstanding. In fact the test pile performed so well that some of the job piles were shortened from 75 ft long to 65 ft long. [ ]

Jan 1, 2003

By Gordon King

The site of the First Quality Tissue plant is located on a previous paper production facility in Lock Haven, Pennsylvania. The new development, which included the construction of a tissue machine building, baled building, converting building, various storage buildings and an electrical switchgear building, required the use of deep foundation systems to transfer loads below compressible fill and alluvial soils. Loading details provided by Jacobs Engineering, the project structural engineer, detailed braced steel frame buildings with typical column loads ranging from 75 to 150 kips and slab live loads of 250 to 300 psf. As an exception to this, however, the tissue machine and stock preparation building, which had a roof height ranging up to 85 feet, had column loads ranging up to 800 kips in addition to high dynamic loads. The First Tissue plant is located in a river valley in the hills of Western Pennsylvania. To evaluate the proposed site conditions and to formulate recommendations for the structure foundations, a geotechnical study was performed by the owner. Approximately 30 borings were advanced to bedrock, with wire-line coring performed in the tissue machine building. The borings disclosed a soil profile comprising of the following:

Jan 1, 2004

By George K. Burke

Jet grouting was first introduced into North America in the late 1970's, soon after the conception of the system in Japan. However, it was not until the mid-1980's that the technique began to gain acceptance through the renewed interest and efforts of specialist U.S. geotechnical contractors. Since this time, innovations by both American users and other users worldwide have further advanced the technology, with a corresponding increase in the range of practical applications. This paper discusses the evolution of jet grouting in North America, from simple single-fluid methods to more complex triple-fluid methods, to the energy-intensive double-fluid and SuperJet methods. Case histories, illustrating a variety of jet grouting methods and applications, are cited to support the newest United States applications.

Jan 1, 2002

By B. C. Slocombe

A large derelict inner city site was regenerated for use as a distribution warehouse. Difficult topography and soils conditions required the adoption of a combination of specialist geotechnical processes. Particular attention was paid to the preparation of the site, programming and capabilities of each technique as additional soils information became available.

Jan 1, 1989

By Robert Fernie

Demographics and Infrastructure demands have led to a significant increase in construction of: deep basements for buildings and, trough structures for Highway and Rail/Metro. Concrete embedded walls used for temporary works can be incorporated into permanent works and because of this (and geological conditions) tend to be favoured in UK. This paper considers British practice in the provision of diaphragm (slurry) walls secant (true and pseudo) piled walls contiguous piled walls Plant utilisation, construction techniques, reinforcement placement, connections, propping, water tightness, tolerances, general UK practices and their relation to design practices are discussed. [ ]

Jan 1, 2000

By Jeffrey R. Hill

To extend the life of the Merchants Railroad Bridge crossing the Mississippi River in St. Louis, MO, the owner implemented a rehabilitation and reconstruction project. The Merchants Bridge provides a key link in the transcontinental railroad system. The bridge is of local importance to the Terminal Railroad Association ? providing a link between St Louis and a rail switching yard in Venice, IL. The intent of the bridge rehabilitation is to keep the Merchants Bridge in service, even though the bridge was originally constructed in the 1890?s. The project involved replacing the East and West approach deck truss spans with new deck girder spans. The rehabilitation program required construction of new concrete piers to support the new spans. In order to reduce the track down time to two, ten day single track shutdowns, the specifications required that all foundation and substructure work be completed while leaving the existing spans in place. The preliminary bridge design specified rock-socketed drilled shaft foundations. Drilled shafts proved to be challenging due to working from beneath the existing bridge, a high water table, utilities, a flood wall, and existing rail way lines. The micropile alternative was technically appropriate given the access limitations, shortened the foundation rehabilitation schedule by several weeks, and realized a significant cost savings to the Owner.

Jan 1, 2006

By Tom Szynakiewicz

Micropiles are routinely used in the United States for foundation support and underpinning applications. The high capacities achievable with the use of micropiles, combined with specialty rigs for easy installation in low headroom and difficult access areas makes them a good choice for situations often encountered on existing commercial projects. The bond zone of the pile is typically drilled into a competent stratum such as sands, gravels or bedrock. In this paper, the authors will discuss a project where the lack of a shallow ?competent stratum? led the geotechnical contractor to create their own bond zone for the micropiles using jet grouting. Due to problematic clay (CH) soils, the original foundation of a six story office building in west Houston had experienced up to five inches of differential movement in-between the shallow under-reamed shafts. The owner desired a permanent solution to the problem without disturbing the majority of the tenants. The structure was underpinned with a hybrid system of jet grouted micropiles as well as jet grouting alone and the structure was re-leveled using hydraulic equipment to within a 0.25? tolerance. Design, construction and sequencing of the project are discussed in the paper. QA/QC methods are also discussed, including coring for verification of jet grout column diameter as well as a full-scale micropile compressive load test. The structure was successfully re-leveled and the entire project was completed without disturbing any tenants on the floors two through six.

Jan 1, 2008

By W. F. Van Impe

The design of piles and of pile groups has remarkably progressed over the past two decades. The in­creasing complexity of the building concept implements a more rational approach of the deep foundation capacity and its interaction with the structure. Moreover, the understanding of the soil characteristics relevant to deep foundation behaviour, is continuously in progress because soil parameters are always more accurately determined; which also contributed a lot to the recent developments in pile capacity design. At last, due to the increasing sensitivity of buildings to deformations, continuous attention must be also paid to pile group settlements. The aim of this report is to discuss some of the mentioned more important pile design developments.

Jan 1, 1994

By Robert G. Lenz

Control of ground water for construction purposes is an everyday occurrence in the U.S. Thousands of pumps are in service at any given time. Most of these applications simply consist of pumping water out of an excavation, generally with the aid of sumps. Modern hydraulic and electric submersible pumps permit these procedures because of their ability to pump solids and take air without losing their prime. These procedures work fine up to a point and permit the contractor to control his ground water problems adequately and at minimal cost. When that point is exceeded, the ground water problems sometimes are compounded. Over-application of open pumping techniques can result in slope failures, cofferdam instability, bottom heaving, boils, loss of ground, damage to adjacent structures and utilities, and assorted other maladys which could and should be avoided. This paper will deal with the options involved in ground water control, a discussion of the unwanted side effects of dewatering, and examples of ground water control projects in various cities around the U.S.

Jan 1, 1988

By Mary Ellen Bruce Large, Antonio Marinucci, Silas C. Nichols

Tip post-grouting of bored pile (drilled shaft) foundations refers to a method where cementitious grout is injected beneath the tip of a shaft to improve the overall performance of the constructed foundation. This technique, when performed satisfactorily and in the appropriate ground conditions, enhances axial load-displacement performance by improving the mobilization of pile’s resistance. Potential benefits associated with tip post-grouting include reduced settlement under loading, better alignment of load transfer curves, and improved ground beneath the base of the bored pile. However, to be able to realize the benefits attributed to this method, the design, construction, of both the bored pile and the post-grouting system must meet a minimum level for quality assurance. The various factors affecting the successful installation and performance of a bored pile (e.g., workmanship, base cleanliness, borehole integrity, and concrete placement) have been discussed by numerous practitioners and researchers in the available technical literature. For a conventional (i.e., ungrouted) bored pile, acceptance is based on a combination of visual inspection, material testing, and the results of integrity and/or performance testing of the constructed pile. A properly executed tip post-grouting program can be a relatively comprehensive and complex process, which is typically evaluated throughout the construction process based on the results of prior projects and/or on test pile(s) at the particular site. For tip post- grouting programs, verification procedures and acceptance criteria should be established during and incorporated into the design process to ensure design intent and objectives are achieved. Project specifications should be produced to ensure performance requirements are achieved. This paper will present and discuss factors affecting the successful execution of tip post-grouting, including grouting criteria, instrumentation, reliability and uncertainty with the method and outcome, and verification and acceptance. INTRODUCTION Constructing bored piles (drilled shafts) is increasingly more challenging given the lack of ideal site locations, tight project site confines, difficult or restricted access, greater demands on drilling equipment, and close proximity to adjacent structures. To evaluate the feasibility of bored piles as an appropriate foundation system, a myriad of factors is evaluated during design, including site conditions and constraints, budgeting and scheduling, reliability and risk exposure, presence of and depth to adequate load bearing soils/rock, and the magnitude of the imposed loading. Moreover, updated design codes increased load demand per element, and improved material strengths have led to more complex foundation designs, larger foundation elements, and significant increases in load magnitude. Monopile (monoshaft) foundations have been utilized where one large bored pile is used in lieu of a group of piles connected via a pile cap. In addition, to accommodate the design criteria, site conditions, and imposed loading, the geometry of the bored piles being designed and installed have been as large as 13 feet (4 m) or greater in diameter and to depths in excess of 260 feet (80 m).

Jan 1, 2018

By George Piscsalko

There are numerous methods currently available to assess the integrity of drilled shaft and ACIP piles. Each method has its advantages and limitations. This paper will compare the various available methods as well as introduce a new method for assessing integrity of drilled shafts and ACIP piles. This new method, known as Thermal Integrity Profiling, determines the integrity of the shaft both inside and outside the reinforcing cage by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements can be made by either passing a thermal probe through a standard Cross Hole access tube, or from embedding thermal wires within the shaft. This Thermal Integrity Profile method will be described in detail and one case history will be presented. Additional testing methods which will be compared include low strain Pile Integrity Testing and Cross Hole Sonic Logging. Advantages and limitations for each method will be discussed.

Jan 1, 2011

By John P. Turner

The behavior of tieback retaining walls depends on many factors, including soil properties, groundwater conditions, construction sequence, spacing and stiffness of tiebacks and soldier piles, tieback loads, and others. The primary design considerations for tieback walls are 1) adequate stability and 2) limiting wall movements. Traditional design methods rely on apparent earth pressure diagrams and experience to predict the forces which must be supported by the tiebacks to provide adequate stability. The required soil properties depend upon whether the soil is sand, soft clay, or stiff clay. Design to limit wall movements is more difficult and the usual approach is to design the wall with an adequate factor of safety for stability and then evaluate wall movements during construction through the use of load tests on individual tiebacks and monitoring of wall movements by optical surveying, slope indicators, and extensometers. If excessive movements are likely to occur, it is often not known until construction is well underway. This approach is reflected in the fact that few tieback walls fail due to a lack of adequate stability, while most litigation involving tieback wall performance is related to excessive movements. Much progress has been made in recent years in methods for predicting the movement of all types of insitu retaining walls (Clough et al. 1989, Clough and O'Rourke 1990). These methods are based upon both experience and analytical methods. This paper reviews the methods currently available for evaluating both the stability and movements of tieback retaining walls. Case histories involving excavations constructed in the downtown Seattle area are used to evaluate the applicability of the available methods to Seattle conditions and to illustrate the importance of soil behavior in tieback wall performance.

Jan 1, 1990