Search Documents

By Ali Ebrahimi, Meena L. Viswanath, John F. Beech, Mustafa B. Erten, Ming Zhu

"Excessive deformation of a cantilever sheetpile wall can occur due to dredging, excavation, backfilling, or long-term creep behavior of soil. A buttressing berm constructed in front of the wall can be considered as a mitigation technique to prevent or decrease the deformation by increasing the passive earth pressure and thus improving the wall stability. The effect of the buttressing berm on the stability and deformation of a sheetpile depends on the berm geometry (i.e., the thickness/depth and the width) as well as the properties of the sheetpile and the adjacent soils. A parametric study was conducted using a conventional limit equilibrium method. Design charts were prepared to evaluate the effect of a buttressing berm and the soil friction angle on the wall stability and deformation. These charts can be used as a tool by geotechnical engineers to make a quick estimate of the required size of a buttressing berm in case of calculated or unexpected excessive deformation of a sheetpile. An analysis of the effect of a buttressing berm on the stresses and deformation of a sheetpile was also compared with the results from finite element analysis. The results of this comparison are discussed.INTRODUCTIONCantilever sheetpile walls are commonly used to support excavations. Sheetpiles are hot rolled or cold formed sections of steel made to interlock with adjacent sections to form a continuous structure providing lateral support. Sheetpile walls can be cantilever walls or anchored with tiebacks. To construct a cantilever sheetpile wall, sheetpiles are driven by pile drivers or vibrated in to a design depth sufficiently below the depth of excavation. Excavation can then proceed in front of the sheetpile wall, which resists the earth pressure loading from behind the wall. The design depth and geometry of the sheetpile wall depend on the soil conditions, the depth of excavation, and the tolerable deformation. In certain cases, when a small buttress of soil can be left immediately adjacent to the sheetpile wall, the required depth or geometry of the sheetpile wall can be reduced or adjusted, which can significantly decrease the cost of procuring and installing the wall. Such a buttress can also serve as a short-term or long-term remedy in case of observed excessive deformation in a constructed wall. Traditional methods of analyzing the stability of a sheetpile wall do not account for the passive pressure effects of this small buttress. In this paper, a parametric study was performed for a variety of soil types and wall and buttress geometries by implementing traditional limit equilibrium methods in commercial software and design charts were created illustrating the effect of a buttressing berm on sheetpile deflection. Selected cases were then modeled in a finite element software to compare the results with the traditional limit equilibrium method. The resulting design charts can be used as a tool by geotechnical engineers looking to reduce the design geometry of a sheetpile wall or address observed excessive deformation in a constructed sheetpile wall."

Jan 1, 2016

By J. W. Slatter

Cast in situ screw piling techniques (both displacement and non displacement) have seen considerable growth in recent years due to competitive production rates, low noise and vibration free installation. However the discussion on the mechanics of auger installation, which has implications on the installation effects and installation forces of screw piling augers, has been almost exclusively targeted towards non displacement techniques and in particular continuous flight augers (CFA). This paper discusses the historical development of the understanding of screw piling auger mechanics in sands and presents a new theoretical model to predict the soil transport and displacement characteristics of both displacement and non displacement augers with variable geometry.

Jan 1, 2000

By James M. Tantalla, Roderic A. Ellman, W. Allen Marr, Scott R. Bamford

"Construction of the powerhouse for the Willow Island Hydroelectric Project required a 100-ft deep excavation inside the limits of a cofferdam and embankment-seepage cut-off wall through soil and rock adjacent to the Ohio River. Portions of the rock had preexisting weak plans and slickensided surfaces with low frictional strength. Stability analyses were performed for critical sections of the excavation to evaluate the stability of the soil slopes and rock cuts using buckling, tension crack, and limit equilibrium analysis techniques. Loading conditions included the 100-yr and intermediate floods, normal pool, sudden drawdown, and seismic design conditions.Stability analyses indicated adequate factors of safety for soil slopes and for rock cuts through the landside embankment sections. However, the results of deep-seated stability analyses through the rock supporting the riverside cellular cofferdam indicated unacceptable factors of safety. Consequently, the riverside portion of the excavation required measures to increase stability. Long, high-capacity rock anchors and deep dewatering wells to lower the site piezometric head were chosen for this purpose.Thirty high-capacity rock anchors were installed on the upstream, riverside, and downstream sides of the cofferdam rock cut. Required rock anchor loads varied from 1,968 to 2,074 kips. The designed anchors consisted of multiple, seven–wire strands with up to 59 strands per anchor. Bond lengths used an allowable bond stress of 100 psi based on the rock bond measured with pull-out tests. Maximum bond and anchor lengths were 50 ft and 140 ft, respectively. Measurements of forces in selected strands and displacements of the excavation showed excellent performance."

Jan 1, 2017

By Timothy C. Siegel, Paul J. Axtell

The Missouri Department of Transportation (MoDOT) recently replaced the Hurricane Deck Bridge that carries Highway 5 traffic across the Osage Arm of the Lake of the Ozarks in Camden County, Missouri. The former bridge was constructed in the 1920's and was supported on pneumatic caissons bearing on dolostone bedrock. The replacement structure is founded on drilled shafts socketed into the bedrock. During the design phase of this bid-build project, a baseline design was developed and Alternative Technical Concepts (ATC's) were allowed from approved contractors. Those ATC's were confidential and not shared between teams. Either the baseline design or the approved ATC design could be bid by the respective contractors. The baseline design included re-use of the 90-year old caisson foundations. Accordingly, an extensive evaluation of the caissons and underlying bedrock were conducted by coring, laboratory testing, acoustic tele-viewer (ATV), and cross-hole sonic logging (CSL) methods. The results of the investigation indicated the caissons were in excellent condition and suitable for re-use. However, a more cost-effective ATC was submitted, awarded, and constructed that did not re-use the existing caisson foundations but rather reduced the span lengths, increased the number of piers in the water, and supported those piers on drilled shafts. Interestingly, the difference in low bid price between the awarded ATC and the baseline design was less than one percent of the construction cost. This paper describes the multiple foundation designs that were necessary for this interesting project. The various foundation evaluations include the existing pneumatic caissons, large-diameter open-ended pipe piles to support the baseline design, and the design of rock-socketed drilled shafts that were successfully constructed in 2012.

Jan 1, 2017

By Joshua R. Omer

A numerical model is developed for predicting the load transfer and settlement behaviour of vertically loaded, bored cast in-situ piles. Based on analysis of full-scale pile tests, closed-form equations are formulated to uncouple the shaft and base transfer resistance components of the pile/soil system. Appropriate parameters are introduced to take into account: (i) the shaft resistance distribution in unlined and partially lined piles, (ii) the effects of ?soft toe? (voided toe pile) behaviour on base resistance development. For convenience, an interactive computer program has been developed in Matlab? with a user friendly interface system. The program can be applied to predict the complete load-settlement curve and axial force distribution in bored cast in-situ piles if reliable soil test data are available. To demonstrate its validity, the proposed method is applied to 4 test piles, which are also analysed using two previously published methods: (a) elastic solution method and (b) layer discretisation method. Methods (a) and (b) above are based on load transfer (t-z) and finite element models respectively. It is shown that the proposed method yields axial force distributions and load-settlement curves that are in good agreement with the observed pile test data.

Jan 1, 2010

By Pierre Gouvin

This paper describes the design, installation and monitoring of a state of the art real time geotechnical/structural instrumentation monitoring system to facilitate tunnel construction under Interstate route I-5 in Seattle, Washington, USA. The project involved removal of existing highway foundation substructures on both North and Southbound lanes as well as the underground reversible high occupancy vehicle lanes. The system utilized state of the art 3-D pulsed laser scanning, wireless sensor networks, automated robotic total stations, tilt beam sensors, narrow angle tiltmeters, and in-place inclinometers. Dedicated real time data loggers, with a web based graphical interface, provided 24/7 access to critical measurements. In addition to the instrumented sections of wall and roadway subsurface which monitored physical measurements at known points, the pulsed laser scanning allowed complete site monitoring coverage where physical sensors were not located. This data allowed post processing at any location enabling the contractor and designer to respond to unforeseen structural responses to construction. Use of the instrumentation system resulted in the early detection of wall movement, and provided feedback to the designers to facilitate construction process changes in order to minimize further movement.

Jan 1, 2010

By Karsten Beekhaus, Sander W. Odijk, Rabea Bahlum, Mazin Adnan, Ayman Abdelh Al Nuaimat, Hassan Farhat

The Arab Potash Company, APC, is one of the 10 largest potash producers of the world. The solar ponds at the Dead Sea, used for the enrichment of the salt content in the brine, are of crucial importance for the first step in the exploitation of the potassium salt. Targeting at the expansion of production in the since over 50 years utilized facilities, the increase of the brine exploitation capacity, reducing the substantial brine seepage losses from the ponds, becomes a crucially required measure. In this context, the remediation measures on the over 11 km long Dyke 1, being a main dyke of the solar ponds system, became inevitable to reduce the brine losses, prevent further development of sinkholes and cavities and hence assuring the stability of the dyke. The highly aggressive environment, the acting hydraulic conditions and the sensitive stratification and nature of the existing ground represented remarkable challenges for the design, as well as its implementation by the construction activities. Royal Haskoning developed a solution addressing the challenges above and targeting at a high sustainability of the executed structure, especially in view of the various geological and hydrological hazards repeatedly occurring in this Dead Sea region, including sinkholes of several meters by diameter and depth. The construction works, consisting of a cut-off wall, with depths reaching down to 31 m, were awarded to Bauer International FZE, a subsidiary of Bauer Spezialtiefbau GmbH. Upon the execution of the first section of 4.2 km length, additional sections were subsequently commissioned, also on further dykes, totaling to about 300,000 m² of cut-off wall. The specific project conditions, such as utilization of cutter technique for the excavation in Halite rock, the stability of open trench exposed to hydrostatic pressure of salt-saturated ground water, resulted in unconventional requirements towards the supporting fluid. The extremely aggressive saline conditions –with a Dead Sea water density of 1.25 tons/m3; one of the world's saltiest water–, were further a decisive factor for the definition of the backfill material concept. Despite its clear advantage for construction of cut-off walls with installed sheet piles, the single-phase system with hardening slurries, fulfilling both functions of excavation support and cut-off wall backfill material, had to be abandoned in favor of the two-phase system, to construct a hybrid cut-off wall made of sheet piles and plastic concrete.

May 1, 2022

By Nicolas Denies, Jeroen de Leeuw, Bart Lameire, Jan Maertens, André Vervoort, Flip Hoefsloot, Noël Huybrechts, Flor De Cock

"In recent years, the Deep Mixing Method has increasingly been applied for the construction of earth and water retaining structures. From practice, it has been experienced that there is a real need to develop execution and design rules adapted to the function of the soil mix wall (retaining wall, water barrier, foundation solution or a combination) including the temporary or permanent character of the application. Based on the results of the BBRI Soil Mix project (2009-2013), a design approach has been developed in collaboration with the SBRCURnet. The present paper briefly discusses the principles of this design approach which takes into account the function of the soil mix wall and the characteristics of the soil mix material. The interaction between the soil mix material and the steel reinforcement can be considered in the calculations depending on the function of the soil mix wall. Design and quality control requirements are given in function of the application and take the lifetime of the structure into account. Durability aspects of the soil mix material are therefore considered in the present design approach.INTRODUCTIONSince several decades, the deep mixing method is used for ground improvement works. A more recent application is the use of soil mix as structural elements such as in the case of the earth-water retaining soil mix walls. Since 2000, due to the economic and environmental advantages of the method, this particular application has shown an amazing growth in Belgium and in the Netherlands. A typical excavation (16 m depth), realized with CSM (Cutter Soil Mix) panels, is shown in Fig. 1. For temporary applications, the questions related to the mechanical characteristics of the material, its permeability and its adherence with steel have been investigated with success within the framework of the BBRI Soil Mix project (2009- 2013) (see Denies et al. 2012 for more details). The durability of the soil mix material remains a complex topic while permanent applications are more and more observed in practice. In order to define an obvious design approach, it was necessary to clarify the potential functions of soil mix walls and to establish the requirements related to their design and construction. The BBRI (in Belgium) and SBRCURnet (in the Netherlands) have therefore worked together to publish guidelines in the form of a handbook titled ‘Soil Mix Walls’ (publication foreseen in 2015). In this handbook, a methodology is proposed for the design of the soil mix walls for which the interaction between steel and soil mix can possibly be taken into account dependent upon the application. Each potential function of the soil mix wall is described (e.g. earth retaining wall, cut-off wall, etc.) and the temporary or permanent character of the application is always considered."

Jan 1, 2015

By A. Felipe Uribe-Henao, Camilo Ballesteros, Luis G. Arboleda-Monsalve, David G. Zapata-Medina

Conventional excavation analysis based on total or effective stress methods can result in inaccurate estimation of ground movements when impervious soil conditions or rapid excavation sequences are not found in the excavation (i.e., assumption of undrained response is not valid). The influence of excavation rate, hydraulic conductivity, and excavation geometry on the fully coupled solid-fluid behavior of a braced excavation in cohesive soils are studied parametrically using PLAXIS2D. The coupled excavation analysis is performed using the Hypoplasticity clay model to reproduce the constitutive behavior of soil and the poro-elasticity Biot’s theory to account for changes in pore water pressure due to deformations in the soil skeleton. Results obtained from the parametric studies indicate that excavation rates to hydraulic conductivity ratios, ER/k, smaller than 0.1 and larger than 104 can be used as limits for drained and undrained analyses, respectively. In practical applications, undrained and partially drained excavation analysis with ER/k larger than 102 resulted in a similar ground deformation. However, smaller ER/k ratios demand fully coupled solid-fluid analysis. An analytical method aimed at predicting excess pore water pressures and determining the required type of analysis associated with soil and excavation conditions, e.g., drained, partially drained, and undrained analysis, is proposed herein to accurately estimate the ground movements induced by the excavation.

By Mai Yuanjian

The stabilization effect in large excavation slope with vacuum wellpoints system during construction of a dry dock located in Guangzhou is introduced in this paper. In-situ observations indicate that the effect of wellpoints for decreasing seepage in slope is remarkable even though the muddy sitty clay in it has poor permeability and the slope can remain its stability well. Meanwhile, a non-linear partial defferential equation has been set up to the whole unsteady seepage process as water level in the foundation pit excavated under water goes down to the bottom and so does the seepage in slope due to dewater by vacuum wellpoints system at the same time. And the finite-defference method has been used to solve the equation mentioned above, which differes from conventional wqy where the equation will be linearized firstly. Since the water heads in slope with wellpoints dewatering are more variable, it is necessary to keep non-linear. The calculation results are in good accordance with observation. Vacuum wellpoinnts for slope stabilization in this work is successful.

Jan 1, 1991

By Yahia M. Al-Smadi

Effect of lateral loading against existing sheet pile wall and distribution of gravity loading due to various number of construction loading scenarios were studied. The objective of this effort was to determine the loading case that permits the contractor to utilize a 400 ton crane at the specified location with the existing limitation imposed on site. Staged analysis was determined as the methodology that will more accurately predict the exiting and additional stress due to the impose crane loading. A reliable and robust analysis (ANSYS) software was used to complete both 2D and 3D finite element model and analysis. Analysis model parameters such as material properties, non-linear behavior of the soil, and meshing are presented and discussed. At the conclusion specific range of crane operation and pick weights operating on existing concrete mat supported on top of an existing tunnel was reviewed and deemed acceptable.

Jan 1, 2010

By Filippo Maria Leoni, Gianluca Pianezze

"As part of the Southeast Louisiana (SELA) drainage program, designed to reduce flood damages in the City of New Orleans and surrounding parishes, the SELA-22 project entailed the construction of a concrete covered canal along Jefferson Ave. and Prytania Street. The scope of the required soil improvement was to replace the soil between two parallel lines of sheet piles with a soil-cement mass to eliminate under-seepage, thus creating a so called bottom plug, and provide structural support for the concrete box culvert. The U.S. Army Corps of Engineers (USACE), New Orleans District, selected the jet grouting technology for the construction of the bottom plug to a maximum depth of approximately 40 ft, and for a total length of approximately one mile. The specialty geotechnical contractor proposed to accomplish the task utilizing their proprietary and innovative elliptical bi-fluid jet grout technology which, by limiting the overlap between adjacent columns, allowed a reduction of the overall number of installations. Approximately 2,400 elliptical jet grout columns were installed in a very challenging environment, especially under a logistical point of view. This paper will summarize the main features of the project, focusing on the innovative technological solution adopted to maximize productivity and on the several challenges faced in such limited and complicated logistical conditions.INTRODUCTIONThe Southeast Louisiana (SELA) drainage program has been designed with the purpose of reducing flood damages in the City of New Orleans and surrounding parishes. This will be accomplished by constructing new pumping stations and better drainage canals throughout. The program was authorized in 1996 by the United States Congress and administered under a project cooperation agreement between the Sewerage and Water Board of New Orleans (SWBNO) and the USACE.Prompted by the severity of damages associated with rainfall flooding in southeast Louisiana, the SELA program consists of several individual project components. The proposed work is located on both the east and west banks of the Mississippi River in the Orleans and Jefferson Parishes, as well as in portion of St. Tammany Parish."

Jan 1, 2017

By George W. Little, John Councilman

"The selection, evaluation, and modification of contractor mix designs for self-hardening seepage barriers, completed by the slurry trench excavation method, can be one of the most critical and challenging tasks to ensure the cutoff wall meets the design performance criteria. Contractor mix designs should incorporate all available geotechnical data, including subsurface soil characteristics, groundwater information, and potential site contaminates. However, the pre-construction mix design can have limitations if subsurface data is limited or shows variability from initial investigations. Placement of the seepage barrier material needs to be evaluated during construction to identify in-situ performance. In one particular case study, the self-hardening cutoff wall mix design was evaluated over a one year period followed by a year and a half installation period, in which, a number of adjustments were made to the laboratory mix design during construction due to performance in the field. Installation for the selected mix was monitored on a real-time basis, using quality control data, as well as early strength and permeability results to determine if adjustments to the self-hardening mix were necessary. Evaluation of early results and relationships between strength and permeability were used to make adjustments prior to achieving the final test results for 28-day strength and permeability. Test results of the installed mix illustrated a direct correlation between strength and permeability. Achieving a minimum unconfined compressive strength was necessary to meet the minimum permeability of the seepage barrier. Other determinations conclude that the thorough development of a pre-construction mix design can have limitations even when all geotechnical data and site conditions are taken into account. Understanding early indicators and key strength and permeability relationships are necessary to determine seepage barrier performance and limitations.IntroductionThe evaluation of contractor mix designs for self-hardening seepage barriers was reviewed for one particular case study where a mix was developed using available geotechnical background information, including considerations for impacted groundwater. Following development of the laboratory mix design, the seepage barrier wall was installed over a one and a half year period, where the contractor mix design was evaluated and modified to accommodate field conditions affecting performance. The objective of the project was to cutoff and collect impacted groundwater and prevent the migration of contaminants to the creek running adjacent to the project. The self-hardening seepage barrier wall was installed using the slurry trench excavation method along 4700 ft of alignment and extended to depths ranging from 20 to 85 ft below ground surface, where it tied in with a low permeability stratum or competent bedrock."

Jan 1, 2016

By Bill Paparis

The thirty year old wharf structures at the Port Authority of New York & New Jersey?s Port Elizabeth Marine Terminal are being modernized for the next generation of Post-Panamax container ships, which require deeper water and larger container cranes. The terminal operator is upgrading the wharf in order to remain competitive, now and into the future. The upgrade coincides with the Army Corps of Engineers? $733 million project to deepen the main shipping channel in New York Harbor. This paper focuses on the structural modifications to accommodate berth deepening and to support the heavier loads of the new cranes. An overview is provided of the design and actual construction, including typical problems encountered when combining new and existing structures. The wharf improvements included: ? Installation of a steel king pile/sheet pile cutoff wall along the face of the wharf to permit increasing the depth from ?12.2 m + 0.61 m to ?15.2 m + 0.61 m ( ?40 ft + 2 ft to ?50 ft + 2 ft) ? Removal of the existing crane rail support beams and installation of new piles and beams to support the increased crane loads ? Replacement of the existing timber fender system with a new system capable of resisting the berthing energy of a 152,000 MT displacement vessel, and having dedicated sections for berthing barges ? Replacing the existing overhead, landside crane electric feeder system with a waterside, cable reel trench system. The work included upgrading the transformer capacity at the terminal for increased crane power demands This paper provides a case history for port administrators, terminal operators, engineers, and shipping lines challenged with upgrading aging terminals.

Jan 1, 2013

By Nick M. Withers, Suthagarann Visvalingam, Cillian Mc Colgan

The level crossings removal project in Victoria is removing 75 level crossings across Melbourne to improve safety by separating trains from traffic, with other benefits such as reduced congestion, an upgraded road network, connected communities and support of urban regeneration. The level crossing at Station Street in Carrum forms part of the scope being delivered by the Southern Program Alliance (SPA), which is delivering level crossing removal works associated with the Frankston Train Line. At Station Street, a rail viaduct consisting of 19 spans and totalling approximately 545 m in length is under construction to remove the former level crossing. The viaduct consists of two parallel reinforced concrete Utrough girders and steel trough girders, one for each rail line. The foundations of the rail viaduct are founded on groups of Continuous Flight Auger (CFA) piles. The characterisation of geological units encountered at Carrum for the foundation design has been based on insitu testing and interpretation of test results from high strain dynamic pile testing (PDA) and Case Pile Wave Analysis Program (CAPWAP) from the Seaford Road Bridge, located approximately three kilometres South of Carrum, in similar ground conditions. By conducting pile load-deformation analyses based on pile testing significant savings were made for the client compared to the original design which was based on more traditional empirical correlations. This paper discusses the pile design methodology adopted using pile test data for this viaduct foundation. The results of this assessment are also compared to existing empirical correlations, and the limitations are discussed. The performance of the adopted pile design methodology using pile test data at Carrum rail viaduct is also discussed.

Nov 1, 2022

By Dan A. Brown

The foundations at the Huey P. Long Bridge in New Orleans presented special challenges for construction due to the requirements for very deep drilled shafts in the Mississippi River beneath the existing bridge structure. Drilled shafts were constructed to depths of approximately 200ft in alluvial soils using a rotator system with full-length segmental casing, and base grouted to improve axial resistance. This paper describes the design and construction of the work platform to provide access to the restricted-access site beneath the existing bridge, the approach used to construct the drilled shafts, and the results of a load test program to verify the axial resistance.

Jan 1, 2010

By Reinaldo J. Villa, Joshua C. Adams

The I-395/SR-836/I-95 reconstruction project is an $818-million design-build construction effort that includes construction of viaduct, segmental and signature bridges in Miami leading into Miami Beach in Florida. Based on the load testing performed during the design phase, the design-build team determined that conventional driven pile and drilled shaft foundations were not feasible for support of segmental and signature bridges. Due to the weak limestone formation and successful use of auger cast-in-place (ACIP) piles in the Downtown Miami area on commercial developments, ACIP piles were selected as a foundation system to support bridges. This is the first time in history where the bridges will be supported by ACIP pile foundations in an interstate highway in the State of Florida. The design build-team worked closely with the Florida Department of Transportation to develop requirements for the load test program. The paper will provide an overview of the geotechnical data collected, results of dynamic/bi-directional load testing performed on test piles, data collected, installation of piles, and lessons learned. The load test program included a total of fifteen test piles with dynamic, bi-directional, and lateral load testing on 30 and 36-inch diameter ACIP piles and instrumented with thermal integrity profiling wires.

Sep 8, 2021

By David Wilshaw

Continuous Surface Wave (CSW) testing has been the “next big thing” in ground characterization for the last 25 years. The technique uses surface geophones to measure the speed at which Rayleigh waves (generated by a vibratory source) travel through the ground over a range of frequencies. The velocity at which surface waves travel through the ground is directly related to ground stiffness; the velocity of shorter wavelengths is influenced by the stiffness of shallower soil layers, while the velocity of longer wavelengths is influenced by the stiffness of deeper layers. Measuring the surface wave velocity over a range of frequencies, therefore, allows a stiffness / depth profile to be produced. Using the small-strain stiffness data measured by the CSW technique greatly improves the accuracy of simple limit state analyses; the data are also of sufficient quality for use in Finite Element modelling. Nonetheless, the technique has suffered from a perception of high cost, low productivity, and poor repeatability. An improved Advanced Continuous Surface Wave (ACSW) testing system has been developed by Ground Stiffness Surveys in the United Kingdom, has been deployed there commercially for several years, and is now available in the United States. ACSW uses an automated electronic control system that generates vibrations (from a purpose designed and manufactured portable seismic “shaker”) at different frequencies, measured across a 3m (10-foot) array of geophones, linked to a robust data acquisition and analysis software package. The range of applications in geologic and geotechnical site characterization includes rapid preliminary non-intrusive site assessments (utilizing published soil correlations); stiffness profiling to detect discrete layers (such as a variation in rockhead); average stiffness profiling for earthwork or ground improvement control testing, Working Platform stability assessments, foundation settlement analysis, rock quality and rippability assessments, and void detection.

Oct 1, 2022

By Ziyad Abunada, David O’Connor, Fei Jin, Abir Al-Tabbaa

"In-situ remediation of contaminated land with deep mixing can enable a multi-technique remedial strategy on the same site combining low permeability barriers, permeable reactive barriers, stabilisation/ solidification treatments as well as ground improvement, delivering significant advantages over alternative strategies. This was the core objective of Project SMiRT (Soil Mix Remediation Technology) which involved the execution of the largest research field trials in the UK to date to provide field validation for this technique. Around 800m3 of soil were treated on a contaminated site in Yorkshire in May 2011 with 6 different treatments, testing ~40 binder compositions and 10 different installation methodologies. Field monitoring, testing and coring activities at the site took place within the first 2 months after treatment and then again at 34 months after treatment. This paper presents an overview of the field activities to date and some 3-year results and assessment of a subset of the treated soil sections. Some good correlations are seen together with some clear differences between treatments. There is generally an observed consistency with depth, with the mixing effectiveness having a more profound effect than the binder composition or content, within the tested materials and ranges. These field trial activities are currently being used in the development of the full-scale commercial remedial strategy for the site.INTRODUCTION AND OVERVIEW OF PROJECT SMiRTWhile there are strong financial and environmental incentives to remediate and redevelop brownfield sites there are also barriers including fear of the unknown, regulatory control, delays, increased costs and the stigma associated with such sites. Hence the remediation process needs to be conducted in such a way to maximise the incentives and overcome the barriers, which is how deep mixing found its niche in the land remediation market. Soil mix technology is such a versatile technique that can perform a number of remediation treatments on the same site. These include low permeability in-ground barriers (cut-off walls), permeable reactive barriers (PRB), stabilisation/solidification (S/S) treatments, other additive related remediation, e.g. in-situ chemical oxidation and bioremediation, as well as soil amendments for greening and also ground improvement all on the same site (Al-Tabbaa et al, 2011). Placed in the context of alternative solutions, soil mix technology could potentially replace the five techniques shown in Figure 1, which would be required to deliver the same treatments mentioned above. Treatment trains strategy, where a combination of techniques in succession are used to both reduce the contamination levels and deal with residual contamination, is becoming common in land remediation and the use of one set of equipment to deliver this would bring about significant financial advantages. In addition, soil mix technology has many other advantages in terms of speed of implementation, elimination of exposure to contamination, elimination of off-site disposal and low cost. Soil mix technology for the remediation of contaminated land emerged in the UK in the mid 1980s and has since been employed in over 30 or so projects, which far exceeds its application to ground improvement for which only a handful of jobs have been carried out to date."

Jan 1, 2015

By Robert B. Bittner

The new gated dam on the Monongahela River at Braddock, Pennsylvania, was built for the US Army Corps of Engineers using an innovative ?In-the-Wet? technology. A key feature of this technology involves construction of the foundations through the water and later mating the completed structure or a shell of the structure to the pre-installed foundation. This paper presents a description of the structure, its foundation, construction sequence and design details required to successfully implement this technology.

Jan 1, 2013