Search Documents

By R. P. Taylor

"This paper covers the development of the property to its present production level of20,000 tonnes per day from the Valley Mine. It will also review the analysis of various case studies for the expansion of the project to its full potential, and discuss the impact of the recent structural change in the copper market on the development of a large low-grade deposit such as Valley.IntroductionIn 1964 Cominco participated, along with a number of other companies and individuals, in the formation of Valley Copper Mines Ltd. This company was formed in order to facilitate exploration on a large number of mineral claims held by these parties in British Columbia's Highland Valley, approximately 400 km northeast of Vancouver (Fig. I). Cominco 's ownership of Valley Copper was gradually increased over the years bot h through shares gained for exploration expenditures and through shares purchased on the open market. By the mid- 1970sCominco' s interest in Valley Copper exceeded 80%.ExplorationExploration from 1964 to 1969 led to the discovery of a massive porphyry copper depo sit now known as the Valley orebody. A claim boundary divided the deposit with 80% of it on Valley Copper claims and 20070 on claims held by Bethlehem Copper which was already mining adjacent copper orebodies. During the period when the Valley ore body was discovered, exploration by other companies resulted in the discovery of the large Lornex and Highrnont deposits nearby. The stage was now set for the Highland Valley to become an important copper-producing area (Fig. 2)."

Jan 1, 1986

By R. Kamguem

The surface of a mechanical part plays an important role in determining performance in service. The presence of scratches left by the cutting or tearing of the material on the surface of the workpiece supports the concentration of stress and strain. This article presents the experimental study for high speed milling of the aluminum alloy 7075-T6, using cutting tools different by the nose radius and coatings (TiCN, TiAIN, TiCN + A12O3 + TiN). A multi levels factorial design of experiment (DOE) and statistical analysis was used. The roughness parameters investigated are Ra, Ra, Rv, Rc, Rsm, and Rk. The results show that the feed rate, the types of coatings and the geometry of the cutting tools have the most significant impact on the surface roughness profil. Surface finish charts according to feeds and cutting speeds were established for each tool tested.

Jan 1, 2011

By G Anders

The effectiveness of two types of powder used in long-wall slashing was compared. The evaluation of the results can serve as a good example of how the application of statistical methods to underground test data can help to minimize the number of tests to be carried out. The conclusions are stated concisely, including a definite assessment of the reliability of the tests. Introduction AN assignment at the Algom Nordic mine called for a performance comparison between 70 per cent Cilgel B and 75 per cent Dygel in longwall stope slashing, particularly taking into account, in both cases, the build-up of bootlegs as dependent on hole deviation. Stopes were usually 8 to 10 ft. high and inclined at about 17 degrees. Starting from a raise, they were widened by consecutive longwall slashes to 60 ft., and, al-lowing for drift pillars, were approximately 300 ft. in length along the incline.

Jan 1, 1964

By T. Maruyama

Tamano Refinery started its operation in 1972 with the cathode production capacity of 84,000 tons per year. After several expansions, the production capacity increased to 228,000 tons per year in 2001. In this paper, we are introducing our next expansion projects starting October 2006. The project expands the production capacity of cathode from 228,000 tons to 260,000 tons per year. The main modification of this project is the conversion to the ISA process and the installation of additional seventy-two cells in the No.2 Tankhouse. The No.1 Tankhouse remains the same, using the conventional process. Half of our starting sheet cells are converted to commercial cells. The other expansions are to enlarge our purification plant. And the incidental facilities are enlarged, for example, circulation tanks, heat exchangers, filtration system, etc. Finally, this paper describes those improvements to our refinery performance and preparing for future expansions.

Jan 1, 2007

By J. Schmidt

Cold drawing of copper wire rod is usually combined with an in-line annealing process to adjust the ductile microstructure of the wire again. One important key factor for successful annealing is the quality of the copper itself. Rod producers can check the recrystallization behaviour of the rod by different methods: chemical analysis, Spiral Elongation Test (SEN) as well as the Rapid Elongation Test (AR) are some examples of common testing methods. The comparison of the results of these methods does not always show sufficient correlations. The paper introduces firstly the SEN and AR-Tests and their different approaches to the mentioned task. The second step is to compare some results of the SEN-Test with the results of the AR-Test and identify causes of deviations. Thirdly, the effect of pre-annealing is discussed, which is especially common for wire rod with diameters of more than 8 mm.

Jan 1, 2007

By M. Huang

Electrodeless conductivity was employed to investigate the feasibility of continuous on-line monitoring of the free acidity of sulphate and/or chloride solutions of Cu and other base metals from various hydrometallurgical processes. These solutions were measured with both commercial and experimental electrodeless conductivity sensors from 15 to 250°C. It was confirmed that hydrogen ion has the greatest impact on conductivity by carrying the bulk of the current because it is the most mobile ion. In combination with a solution speciation analysis the conductivity sensor can be calibrated to account for the contribution of Cu electrolytes as well other dissolved salts allowing fast and accurate on-line measurement of free acid. The sensor was tested at both lab and pilot scale with very good performance. The average difference between the measured and the titrated acid concentration was less than 5%, which is excellent for industrial applications.

Jan 1, 2007

By O. -J. Siljan

"Refractory materials are an integral part of aluminium production. One special feature of aluminium making is the prominent role of sodium in all parts of the production process. This presence of sodium inflicts stresses on the refractory materials through reactions and may cause severe damages to the refractory linings. The present paper address possible reactions between sodium and refractories in anode bake furnaces, electrolytic pots and casting furnaces. The discussions presented in the paper points to the importance of selecting materials with excellent alkali resistance in all parts of the aluminium making process, although alkali resistance is not the sole parameter to determine refractory life-time. ""Acid"", i.e. silica-rich alumino-silicate refractories are shown to be the best materials for aluminium electrolysis cell potlinings, whereas high- alumina refractories based on minerals like andalusite seems to be the preferred choice for anode bake furnaces as well as cast house furnaces."

Jan 1, 2004

By T. Belem

In-stope backfill will cure under effective stress, which develops due to a combination of mechanical consolidation (free draining material) and ??chemical consolidation?? (self-desiccation mechanism). A good knowledge of all the drainage and consolidation characteristics of cemented paste backfill is crucial for a better design of underground backfilling sequencing. From many of the existing results and studies done by various authors, as well as the availability of some in-stope backfill pressure data measurements during and after filling, it is possible of developing a procedure of backfilling sequencing. Hence, the objective of this study is to provide a guide for underground backfilling sequencing in the view of preventing the development of excess pore pressure that will affect both the stability of the barricades and the strength development of the backfill. This will be possible by considering the interaction between consolidation/drainage rate, filling rate and binder hydration rate.

Aug 1, 2013

By A. Bauer

The correct application of large crater blasts in unfrozen tar sand is an effective means of resisting frost penetration during winter. This results in much higher productivity and considerably less down time with excavators during winter operations. The resulting flatter angle of repose of the highwall has readily been accommodated with slight modification to bucket-wheel excavator operating procedure. Other mining schemes call for large draglines to be located on top of the highwall, which can be as high as J80 feet. The question now arises as to the effect that blasting might have on the stability of such a situation in which the highwall includes potential planes of weakness. This paper applies blast vibration data from large-scale blasting in tar sand to the stability analysis for typical production situations likely to be encountered and indicates safe scaled distances to be employed between dragline and blast.

Jan 1, 1979

By J. E. Zajic, E. A. Sullivan, T. R. Jack

"The release of vanadium, iron, nickel and titanium from the cokes produced in the upgrading of Alberta oil sands bitumen has been assessed for simple chemical leaching processes. Flexicoker coke (Exxon Engineering and Research) has been found to be quite amenable to the recovery of vanadium as well as nickel, iron and some titanium by these techniques, whereas fluid coker coke (Syncrude) and delayed coker coke (Great Canadian Oil Sands) are relatively intractable under the mild conditions employed. The factors affecting the extent of vanadium release are discussed in terms of the surface area accessible, the wettability of the material, and the chemical and physical composition of the coke particles in each case.A novel biologically assisted heap leaching procedure for f1exicoker coke is also described, based on the growth of the chemolithotrophic bacteria, Thiobacillus thiooxidans A TCC 8085, on elemental sulphur added to the coke."

Jan 1, 1980

By J. M. Ortiz, J. Haas, W. Kracht, G. Pamparana

This work explores the effect of ore hardness variability on the design of a solar photovoltaic system with battery storage and grid backup, to operate a semi-autogenous grinding mill (SAG). First, a case of two synthetic ore populations was studied, without any consideration of spatial distribution. The mean and variance of the ore hardness (measured in specific energy consumption) of both populations were subjected to a sensitivity analysis. The operation was evaluated with one and two stockpiles. The latter allows classifying according to ore hardness to adapt the SAG energy consumption to the solar cycle. The results show that using two stockpiles allows achieving a larger autonomy (i.e., fewer energy imports) at lower total costs, especially when the difference of mean hardness between the two populations is large. The difference in variance (between the two populations) has a smaller impact on the design recommendations. Second, a case study was performed considering the spatial distribution of geometallurgical units. Two cases were considered: (a) brownfield, when there is historical information of the actual variability of the ore hardness; and (b) greenfield, when the system design relies mainly on geometallurgical modeling. Brownfield and greenfield planning result in similar sizing recommendations of the solar power plant if precise drill cores are available. In this case, geometallurgical modeling is an effective tool for forecasting the energy demand necessary for designing the power plant. INTRODUCTION Solar energy can help make mining more sustainable (Moreno-Leiva et al., 2017). With falling battery costs, an autonomous solar supply is soon to become an economical alternative in many parts of the world, even in the presence of a larger power grid (Child et al., 2017). Although this, places with high solar radiation such as the Atacama Desert in Chile, nowadays show a large potential of incorporating solar energy as a supply of energy. Many of the Chilean copper mines are in this zone making it interesting to study their compatibility and potential of integrating this renewable source to their operation. The power demand in a copper mineral processing plant is determined by the main power loads in grinding and flotation, with grinding typically the largest power consumer, especially the semi-autogenous grinding (SAG) mills (Wei and Craig, 2009). In Chile, it corresponds on average the 50% of the electrical energy consumption (COCHILCO, 2013). Solar energy production is determined by the irradiance perceived into the solar photovoltaic (PV) panels (which varies through the geographic location) and several other climatic parameters such as the current season, humidity, temperature, altitude, and others (Molina et al., 2017). Also, solar energy is only generated during the sun hours, getting to a maximum generation at a certain peak hour during midday, and finally dropping to zero during the night. This shows a cyclic parabolic profile as shown in Figure 1. Due to the SAG mill operated continuously, the power supply always must be available. During the night, to continue supplying the energy, it is necessary to complement the solar power generation with a battery energy storage system (BESS), which will act as a power backup and a buffer. For the optimal sizing of this PV- BESS system, information of the demand profile is needed (Pamparana et al., 2017). In the case of the SAG mill operation, the resulting demand relates to the ore-hardness for a specific throughput and grind size (Morrell, 2004). Therefore, for a given throughput and target grind size, a harder ore would require more power, and variable hardness results in more variable demand and a subsequent need for larger energy storage (Bueno et al., 2015). Due to the ore-hardness variability and the operation of the mill, the power demand profile in inherently variable.

Jan 1, 2019

By M. M. Papic, G. M. Kimber

"Hat Creek coal was treated by the liquid solvent extraction process in a continuous plant at the U.K. National Coal Board Coal Research Establishment.Extraction levels of over 80 per cent dry-mineral-matter-free (dmmf) coal were achieved.Total light oil yield was around 47 per cent of the dmmf coal. The light oil was shown to be a good feedstock for secondary refining into gasoline, jet fuel and diesel fuel.In spite of the high mineral matter content of the coal the solid residue was successfully removed from the coal extract by filtration.IntroductionBritish Columbia Hydro (BCH) and the National Coal Board of Great Britain (NCB) undertook a joint project to test the Hat Creek coal from British Columbia in the NCB's coal liquefaction process designed to produce transport fuels and feedstocks for the chemical industry by the liquid solvent extraction of coal(1), In this process most of the coal is dissolved in an aromatic solvent and the residual solids consisting of mineral matter and undissolved coal are removed by filtration. The resultant coal extract solution is fed to a hydrocracker for conversion to light liquid products and a fraction suitable for recycling as solvent. The light liquid products can be converted to gasoline and diesel fuel in a secondary refining stage.The dissolution of the coal is effected by heat-treating a slurry at a temperature in the region of 400°C which causes some bonds in the coal to rupture with the formation of radicals(2,3). These radicals are stabilized by hydrogen transfer from the hydroaromatic groups in the solvent, resulting in a reduction in the molecular weight of the coal. In the absence of donor groups the radicals combine to form an insoluble high molecular weight product(4). From studies of the kinetics of these reactions it has been shown that the formation and stabilization of the radicals is rapid at temperatures around 400°C(2,3). The dissolution of the depolymerizing coal is, however, relatively slow and the need to ensure complete dissolution in order to achieve a high extraction restricts the selection of digestion time(5). Further, it is important that digests do not contain depolymerizing coal as it may re-form under the applied stress in the filter cake inhibiting flow through the bed and resulting in low filtration rates(6).Thus, in practice relatively long digestion times are generally required in order to ensure complete dissolution of the depolymerizing coal, while it is also important to avoid depletion of the hydrogen donor groups in the solvent which would lower the rate of hydrogen donation to the coal and thus reduce the extraction yield and adversely affect the filtration(7). Clearly it is desirable to optimize the digestion time and temperature with regard to the extraction yield and filtration properties.The precise control of the distribution of products from the hydro-cracker is important for the composition of the recycle process solvent. The principal functions of the solvent are to provide a source of donatable hydrogen and a vehicle for the dissolution of the depolymerizing coal. Hydrogen transfer from the solvent, achieved by the conversion of hydroaromatic to aromatic groups, stabilizes the radicals formed by thermal cleavage of some of the bonds in the coal resulting in a progressive reduction in the size of the coal molecules(8,9) and dissolution in the solvent. The combination of radicals would result in the formation of insoluble material and a reduced extraction yield of the coal(4). Thus to achieve a high extraction yield the solvent should contain sufficient hydrogen donor groups to prevent extensive radical combination. The composition of the solvent should also be controlled to allow dissolution of the depolymerizing coal and to prevent precipitation of this material during the subsequent processing of the coal digest and extract solution. The formation of a precipitate not only reduces the extraction yield of the coal and adve"

Jan 1, 1985

By R. D. Livingstone

"THE LETHBRIDGE COAL FIELD lies mainly .to the north and west of the city of Lethbridge. Mining carried on in this area for over eighty years until 1965. Before the building of a railway the coal was carried by bullock wagon to Montana for use in smelting, and for a while by river boat to Medicine Hat for railway use. The single, almost flat, worked seam is designated the ""Galt"" seam and is about 1.5 metres thick. It belongs to the Belly River formation and is under cover of 80 to 180 metres of weakly stratified sediments. A complex system of cross faults adds to the mining difficulties. Close timbering required in the entries and rooms reflected in a high timber cost and lower output per man shift. The coal is High Volatile"" C"" bituminous in rank with maximum gross calorific value of 11,200 Btu per pound and with a well defined cleavage. Roof conditions in the field range from very tender and very heavy on the south end of the field and west of the Oldman River to a more stable character to the north. Relatively speaking, the whole field would earn a rather tender rating and definitely so in relation to many U.S. fields. Floor conditions are characterized by a bentonitic type heaving in the south end of the field west of the Oldman river to a more stable situation in the north, which can tolerate shuttle car operation if kept drained. Water problems are minimal, except paralleling the Oldman River, where the seam dips below the river level. While vigilance is necessary to prevent accumulations of gas, the volume is rather limited. The seam was entered by shafts, except where small mines were located along the Oldman river banks and gained access by drifts. The coal seam was developed by driving either 3 or 4 Face entries 2 1/2 metres (8 ft) wide on 18-metre ( 60-ft) centres. Sets of dual butt entries driven at right angles to the Face entries completed development work. Normally rooms up to 8 metres wide were turned off the butt entries on up to 11 - metre centres. These were worked in groups of three to five, depending on the roof conditions, and normally advanced 60 m (200 ft). In some areas rooms had to be abandoned short of their objectives due to roof pressure, heaving floor and intermittent work."

Jan 1, 1985

By Laxman M. Amaratunga, Glen G. Hein

"Most mining operations utilize the tailings coarse fraction for backfilling while the fines have been traditionally disposed on surface in tailings ponds. Recently, paste fill has been developed which uses a fraction of the fine tailings (10-30% w/w of <45 µm) in the fill (Brummer and Moss, 1991). This development allows a mining company to use a portion of the fines for backfill, but still requires surface impoundment of the unused tailings. Reactive tailings have the added problem of generating acid after being oxidized in the presence of air and water. Treating acid mine drainage (AMO) from these ponds has proven to be a costly environmental problem and a long term liability.One practical method to reduce the environmental impacts associated with the tailings pond is to modify the physical and chemical prope1ties of the fine tailings so that they can be utilized in an environmentally safe manner. This was accomplished by agglomerating the tailings into pellets and using theses pellets as a coarse aggregate in a total tailings paste fill. This technology does not require any supplemental sand or gravel to be added to the fill.This paper presents the ongoing research into utilizing these tailings agglomerates as a coarse aggregate fraction, in order to create a total tailings paste fill which has supe1ior strength characteristics.IntroductionThe Canadian mining industry produces more than 500 million tonnes of tailings and waste rock annually. The waste rock is usually returned underground for use as rock fill in underground support with the tailings remaining to be disposed of in tailings ponds. Tailings consist of a coarse and fine fraction, and can be either reactive (acid generating) or non-reactive. In an effort to minimize tailings disposal, the coarse fraction has been used underground in backfill along with alluvial sands. This diversion of the coarse fraction, however still requires that the fine fraction be disposed of in tailings ponds. This disposal creates the potential for acid mine drainage (AMO), since in the presence of air and water, reactive sulphide tailings can generate acid. It is therefore an important goal in the mining industry to minimize the disposal of fine tailings into tailings ponds since the treatment of AMO is a costly and long-te1m environmental liability."

Jan 1, 1997

By J. X. Guo, A. Pindred, J. Moore

"Two modified centrifugal flotation cells (CFC), Q2 and Q3 models, have been developed for froth flotation. The operating mechanism of Q2 uses a rotating bowl to create a centrifugal force on the feeding slurry. Froth concentrate is collected on the central top of the cell and tailing is discharged along the top edge of the rotating bowl. The Q3 utilizes a vertical rotating feed pipe to introduce the feed slurry into a stationary flotation column cell. A centrifugal force is also created by a rotating pipe for the feeding slurry. Froth concentrate floats over the cell and tailing discharges through the bottom of the cell. The centrifugal force causes the flotation recovery of fine particles from CFC to be higher than from the conventional cell. The major operating variables of CFC are the rotating speed, air flow rate into feed slurry, and slurry feeding rate etc. Flotation tests have been carried out on synthetic mixtures of galena-silica and chalcopyrite-silica, as well as some natural base metal ore samples. Parallel tests were also conducted on a conventional flotation cell. The comparative test results demonstrated that both Q2 and Q3 have the advantage of higher recovery of finer than 10 µm mineral particles, which are very difficult for the conventional non-centrifugal flotation cell to recover. The grade-recovery curves produced from CFC are equivalent to or better than the conventional flotation cell. There is a potential in the future for the CFC to be employed in slime flotation.1. IntroductionA centrifugal flotation cell (CFC) was originally developed by Clean Earth Technologies [I] to separate oil from water and was subsequently applied in froth flotation. Figure 1 illustrates the design of the original CFC, in which a vertical feeding pipe is attached to the center part of a rotating drum and a stationary shell encloses it to direct the float froth and tailing discharge. The slurry flows down to the bottom of the spinning drum, gets in touch with a screen of air bubbles and then migrates outwards under the effect of centrifugal force. After the mineralized froth enters the rotating cell, it is pushed back to the inner surface. The overflowing froth is collected in the froth launder while the tailing slurry is discharged through orifices along the outer rim of the drum."

Jan 1, 1998

"At the May 15, 2006 and the May 1, 2007 Canadian Securities Administrators (CSA) Canadian Institute of Mining, Metallurgy and Petroleum (CIM) meetings in Vancouver and Montreal, CSA requested CIM consider certain issues arising out of the CSA review of Technical Reports and public disclosure, in general, regarding the practice of estimation and reporting of Mineral Resources and Mineral Reserves. The following is a summary of the issues raised by the CSA and the responses of the CIM.Preamble: At the May 15, 2006 and the May 1, 2007 Canadian Securities Administrators (CSA)-Canadian Institute of Mining, Metallurgy and Petroleum (CIM) meetings in Vancouver and Montreal, CSA requested CIM consider certain issues arising out of the CSA review of Technical Reports and public disclosure, in general, regarding the practice of estimation and reporting of Mineral Resources and Mineral Reserves. The following is a summary of the issues raised by the CSA and the responses of the CIM Reserve Definition and the CIM Estimation Best Practices Committees (the Committees). This information is intended to provide the Qualified Person (QP) with further guidance when estimating Mineral Resources and Mineral Reserves and in preparing a technical report written under National Instrument 43-101 (NI 43-101). Several members of the CIM Reserve Definition Committee, the CIM Estimation Best Practices Committee and some members of the Committee for Mineral Resources International Reporting Standards have reviewed these issues and provide the following commentary.Issue 1. - CSA requested CIM review and comment on the selection of an appropriate commodity price to be used in Mineral Resources and Mineral Reserves estimates.Commodity prices are used in the estimation of Mineral Resources and Mineral Reserves and in the economic analysis of a property. In times of rapidly changing commodity prices, or when prices are at the extreme ends of a commodity price cycle, the QP has a difficult job in selecting an appropriate commodity price.• The selection of appropriate technical variables, including commodity price, is clearly the responsibility of the Qualified Person (QP). The QP must describe the reasons for selecting these variables, including price, in the technical report.• The definition of a ""Mineral Resource"" contains the wording ""reasonable prospects for economic extraction,"" therefore, a QP must select economic parameters, including commodity price, that will result in an estimate of Mineral Resources and Mineral Reserves that have ""reasonable prospects for economic extraction""."

Jan 1, 2003

By S. Eckert, M. Reuter, O. Keplinger, D. Obiso, N. Shevchenko, M. Akashi

We report on laboratory experiments focusing on bubbling phenomena arising from gas injection through a top submerged lance (TSL) in a liquid metal layer. The objective of this study is to reveal the characteristics of the formation and behaviour of the particular bubbles at different gas flow rates and submergence depths of lance. Visualization was performed in the eutectic alloy GaInSn using X-ray radiography. Argon bubbles were injected through the injection positions at three different submergence depths. Essential parameters such as the bubble size, bubble shape, detachment frequency and the two- dimensional gas distribution in the flat vessel were obtained by image processing. The results show that the deep position of the submerged lance causes an asymmetric large-scale circulation inside the fluid vessel. Bubble detachment frequencies were calculated by Fast Fourier Transformation from fluctuations of the image intensity in the vicinity of the nozzle injection point. This frequency does not show strong variations with respect to changes of the gas flow rate and the submergence depth of the nozzle. An increasing gas flow rate results in an increasing two-dimensional projected bubble area and the occurrence of a significant number of small bubbles being trapped by the strong fluid flow in the liquid metal layer. INTRODUCTION The Top Submerged Lance (TSL) process has been an essential component of the metallurgical industry since the emergence of first concepts about 50 years ago (Floyd, 2005). The process, which is characterized by blowing reactive gas through the submerged lance into a liquid bath, was developed mainly for improving the tin smelting process and has been applied for waste treatment or the production of several metals such as copper, lead, nickel and zinc. The productivity of the reactor is determined mainly by the efficiency of the chemical reaction between the gas or solid particles and the liquid. To achieve a high efficiency requires good exchange between the gas-liquid phase and therefore a large interface area. The efficiency changes greatly with the number and size of bubbles injected from the nozzle and the extent of splashing on the free surface. The degree of turbulence in the bath plays a decisive role here. For the reason, the design of an efficient TSL process requires a profound knowledge of the fluid dynamics especially for complex multiphase flows.

Jan 1, 2019

By G. R. Heffernan

"In the early 1970ssteelmakers worldwide were looking forward to many years of expansion and profitability. Huge government investments in Europe, the United Kingdom, Japan, Brazil, and Venezuela were committed in anticipation of growing market s based on long-term OECD forecasts. In 1973 the first OPEC oil shock occurred. Steel demand shrank. Restructuring became the buzz word of the day as billions of dollars in taxpayers&apos; money was poured into eliminating excess capacity and labour. In the United States, where government help was not available, inefficient companies went bankrupt; capacity was cut to 100 million tons from 155 million tons. The industry throughout the industrialized world shrank. By 1979the world economy seemed back on track and a modest degree of optimism could be detected in the international steel fraternity. Then came the second oil shock. By 1982 the industry was in the midst of another shakeout. More bankruptcies, more rationalization, and fewer jobs resulted. In Canada some well-known companies came close to the brink as low prices and high interest rates took their toll. In the light of the turmoil in the steel market over the past 20 years an attempt to forecast the trends through to 2001 is intimidating.However, there are good reasons to be optimistic today about both markets and technology.An economic super power is emerging in western Europe as 1992 draws near. The creation of a single market of 320 million well educated and economically ambitious people has major positive implications for steel demand. The mega projects of the channel tunnel, a European network of high speed railways, and the London docklands are the forerunners of greater things. Still to come is another $200 to $300 billion by the year 2001 in identifiable major projects for highways, railways, airports, water and sewage systems. Add to that the demands of an increasingly affluent population for automobiles, appliances and housing. On top of all that place large increasing demands for electric power and you have a potential beyond anything seen during the 1970s and 1980s. In 1988 the EEC steel industry operated at 90% and in 1989 at 92% of effective capacity. A surge in spot prices indicated that 92% was close to the ceiling. This pace moderated in early 1990 but any slack will probably be taken up rather quickly."

Jan 1, 1990

By J. Bensabat, B. Figueiredo, A. Niemi, J. Rutqvist, C. F. Tsang

"A hydro-mechanical model was developed to study the interaction between mechanical deformation and fluid flow in the fault zones during CO2 injection and storage at the Heletz site which was chosen as a test site for CO2 injection experiments in the framework of the EU-MUSTANG project. The potential reservoir for CO2 storage at the Heletz site consists of three sand layers separated by lowpermeability shale layers. The potential consequences caused by fault reactivation, focusing on the shortterm integrity of CO2 storage, are evaluated. The difference in the results obtained by considering the three-layer as an equivalent layer storage formation is analyzed.INTRODUCTIONLarge-scale storage of CO2 in deep underground reservoirs may cause considerable pore-pressure perturbation as well as flux migration and concern has been raised over whether shear slip displacements may be induced in nearby faults, as a consequence of their reactivation. A state-of-the-art review can be found in Rutqvist (2012), which describes the various possible effects resulting from CO2 injection into a deep sedimentary basin, including those involved in reservoir stress–strain changes, micro-seismicity, caprock sealing performance, and potential fault reactivation. Moreover, several studies have recently shown how CO2 injection may produce seismic events both on major faults (i.e., large faults with large initial shear offset) (Cappa & Rutqvist, 2011a, b, 2012), and on minor faults that might have gone undetected during the site characterization, e.g., faults less than 1 km long and without detected initial offset (Mazzoldi et al., 2012).The present paper is concerned with the Heletz formation which was chosen as a test site for CO2 injection experiments in the framework of the EU-MUSTANG project. The Heletz site located at the southern Mediterranean coastal plain of Israel and the structure is an anticline fold with a crest of about 4 km by 2 km. The structure is gently dipping to the east, truncated by a pinch-out line to the west and subdivided into a number of blocks by transversal normal faults with small displacements. The water table is located at 300 m below the land surface. An areal sketch of the site with the elevation of the caprock and the location of the borehole that has been chosen for the CO2 injection experiment is presented in Figure 1."

Jan 1, 2015

By A. Torkian

Copper mining operations have increased in Iran in the past decades due to price increases and potential for creating jobs in developing countries. Iran consists of many copper mines. The mining operations have a positive economic impact on the region, but may also be the cause of adverse environmental effects. Environmental aspects and the health impact of respirable particulates on the communities and agricultural production in the immediate vicinities have been under scrutiny by the regulatory agencies to ensure sustainable development. The impact of an open-pit mine on the air quality and extent of particulate pollutant dispersion in different directions and times is the focus of this paper. The results of the modeling have been validated through ambient air monitoring. Monitoring stations were installed in different areas within the mine unit operations and around it including background areas where PM10 values were 7 µg/m3. Outside the Complex, particulate concentrations were monitored in 9 different stations and up to 25 km distance. Modeling of point, area, and volume sources was conducted using a 9- year meteorological database. The results showed that particulate quantity decreases rapidly below local standard value of 150 µg/m3 at 2.5 km around the mine and the main pollution is due to the crusher and tailings dump areas. Model outputs were compared to the actual values measured by the air quality monitoring network including villages and crop fields. High overall correlation of about 76% was obtained for most of the locations but lower values were reported for more complex terrain in the region. Remedial actions recommended included road water spraying and better management practices to avoid overloading trucks.

Aug 1, 2013