Search Documents

By J. A. Maritz

"The Hedley and Grant formulation for pillar strength has been widely adopted by the South Africa hard rock mining industry. Today, some forty year later, this formula still provides the foundation for pillar strength calculations when designing for stability and utilising pillars in mine layouts. Various mine specific back analyses were conducted to adjust the equation parameters based on underground observations of failed pillars and comparing to the pillar stresses calculated using numerical models. In all these instances, the influence of shear stresses was ignored. The key to more representative pillar strength estimation is a better understanding of the pillar loading environment.In this paper, special mining cases are evaluated and the existence of shear stresses on the pillar loading environment is illustrated. By revisiting some back analysis data for optimisation of the equation parameters, recommendations were made in respect of the influence of the shear stress component and on how this should be considered in determining the pillar strength.INTRODUCTIONCommon practice on flat dipping, shallow and intermediate depth ore deposits in the South African hard rock and coal mining industry is to exploit the mineral resource using a room-and-pillar layout. The design methodology is mainly based on a Factor of Safety (FoS) approach, where the strength of the pillar is compared to the effective load on the pillar. In these environments, FoS values of 1.6 are applied as it was found to correspond to a probability of failure in coal mines of 0.001. As discussed by Ryder and Jager (2002) page 279: “For lack of anything else more substantial, the figure of 1.6 is generally used in hard rock pillar design in South Africa”. Dependant on the designed purpose of the pillar, the FoS might be selected as high as 2.0 where long term stability is required. The factors directly influencing the FoS include the pillar height (which is linked to the mining height), effective pillar width, a rock-strength factor and extraction ratio."

Jan 1, 2015

By C. L. O?Brian

Note: The figures quoted and used herein have been collected and furnished by the Dominion Bureau of Statistics. Without the help and willing co-operation of the officials of the Burreau, this study would not have been possible. Introductory and General Coal has one unique quality that distinguishes it from other minerals, one that is too, often forgotten. This is the quality of ubiquity. No other single mineral supplies such a wide and varied range of human requirements nor, up to the present, is there any indication of a rival in this regard. There is, consequently, reason for individual study of each of the major portions of the overall market for coa1. The provision of heat for our homes is a necessity of life in our Northern climate and the largest single source of this heat is coal. It is intended to present here a factual survey of the use ?of coal in home heating throughout Canada and the effect of these requirements upon the production of coal and the development of this phase of the mineral industry. The coals used for house heating in Canada fall into two more or less distinct classes, the very low volatile fuels such as anthracite and including coke, and the bituminous coals, including the sub-bituminous and lignite types. The bituminous coals are, of course, consumed in very large quantity by industry and the railways and are the most important type both in tonnage and in respect to the area supplied. Canada consumes annually for all purposes some 4,400,000 tons of anthracite, 4,300,000 tons of coke exclusive of Petroleum coke, and some 40,000,000 tons of bituminous coals. This is a fair measure of the relative importance to the overall economy although it will be seen later that the concentration of the household use of anthracite and coke into one area does create a considerable problem.

Jan 1, 1951

By M. Roy, Y. Roux, R. McIvor

"La Compagnie Minière Québec Cartier at Port Cartier. Quebec, utilizes six parallel wet grinding open circuit ball mills to grind iron ore concentrate for the pellet making process. In an attempt to improve grinding efficiency, a mix of 605 25 mm (1 in.) and 405 38 mm (1 ½ in.) grinding balls was charged to mill D while the opposite mix was used in all the other mills. Because media costs were higher for mill D, it was necessary to find out if the smaller balls provided a net economic benefit. Therefore, a test program was undertaken to determine the relative efficiency of the charge in mill D compared to the other grinding mills. Mill F was chosen for comparative efficiency measurements.The first problem was to choose a suitable definition of grinding efficiency. In management's view, previous attempts to quantify milling performance using population balance modelling were ineffective because they were unable to relate breakage rate functions to grinding circuit economical in any meaningful way. Work index analysis was also not favoured because of a number of complicating effects, including the fineness of the feed and product streams and open circuit grinding.It was decided to adopt a recent innovative approach which had been successfully applied to closed-circuit ball milling. For ""functional performance analysis of ball milling"" (McIvor et al., 1990; McIvor et al., 1991), a size criterion is first chosen to define ""fines·' and ~'coarse particles"". In this case 45 microns (325 mesh) was chosen to distinguish fines from coarse material. The relative grinding efficiency of each ball mill environment would then be ~e cumulative grinding (disappearance) rate of coarse (plus 45 nucrons) material per kilowatt hour of energy applied to the coarse material in the mill, divided by the grindability (measured in the laboratory) of the coarse material in the mill feed.Because the disappearance rate of coarse particles is also the production rate of fines, the following equation can be written for the efficiency of the mill environment, Effe, as defined above:"

Jan 1, 1994

By J. D. Gillaspie, D. T. White

"Sulphuric acid atmospheric leaching of nickel saprolite / garnierite ores was proposed in the early twentieth century, prior to the development of the pressure acid leaching process for limonite ores. Sulphuric acid leaching with alkali addition for iron precipitation as jarosite has been considered periodically since the early 1970s, shortly after the development of the jarosite process for iron control in zinc refining. In the late 1990’s a series of flowsheets were proposed and tested involving simultaneous atmospheric leaching, iron precipitation and acid regeneration. These were considered particularly suited to sequential leaching of limonite and saprolite ores. A number of laterite sulphuric acid leaching processes utilising this chemistry have been put into commercial operation. Similar sequential leaching flow sheets involving precipitation of iron as goethite were also developed and piloted. This paper will firstly describe some of the important historical developments of both the jarosite and goethite processes. It will then provide descriptions of the commercialised processes involving alkali jarosite/alunite precipitation, with special emphasis on the downstream impurity removal requirements necessary for efficient recovery of nickel and cobalt from solution.INTRODUCTION This paper is a summary and extension of previous works with which the authors have been involved, on the subject of sulphuric acid leaching of nickel laterites (Adams, et al., 2004), (Liu H. , Gillaspie, Lewis, Neudorf, & Barnett, 2004), (White, Miller, & Napier, 2006), (White, 2009), (White & Gillaspie, 2013), (White & Gillaspie, 2015). Some of the historical developments of both the jarosite and goethite leaching-precipitation processes will be described, followed by a description of the commercialised sequential nickel laterite leaching processes, involving alkali jarosite/alunite precipitation and acid regeneration, with a comparison to the equivalent goethite based processes. These will include Jarosite Atmospheric Leaching (JAL), Goethite Atmospheric Leaching (GAL) and combined Pressure Acid Leaching – Atmospheric Leaching, termed EPAL®. There will also be an explanation of the downstream impurity removal requirements necessary for efficient recovery of nickel and cobalt from solution."

Jan 1, 2016

By Stephen Mcgibbon, Tim Twomey

"Abstract - The High-grade Zone (HGZ) was discovered 5000 ft (1520 m) below surface in the hangingwall of the existing orebody, 46 years after the Red Lake mine first went into production. The very rich ore of the HGZ is characterized by a remarkably abundant distribution of visible native gold. The location of this discovery challenged conventional wisdom at the time and its genesis has yet to be fully understood. Textural observations of ore within carbonate veins as well as crosscutting relationships suggest peak-metamorphic emplacement for at least some of the gold. Post-lamprophyre dike remobilization of gold is locally observed in the HGZ. Structure and dilatancy were the key elements for localizing ore at the Red Lake mine. Ore occurs where a fault trend intersected folded ultramafic volcanic rock that created a semi-permeable cap-rock to ore fluids ascending the "feeder" structure. This was enhanced by strong competency contrasts between the eastern ultramafic rocks, felsic volcanic rocks west of the HGZ, and the mafic volcanic host to ore - an exceptional environment for the development of protracted dilatant fluid pathways for gold deposition.Development in the HGZ began in February 2000 and reached commercial production on January 1, 2001 at a capital cost of US $53 million. December 2001 reserves are 1.9 million short tons (1.73 Mt) at an average cut and diluted grade of 2.05 ounces per ton gold (70.5 g/t) containing 3.8 million ounces of gold. The extremely rich ore presented a unique challenge in grade estimation for the Geology Department at the mine. The historic cutting factor was replaced by a statistical method as more data were collected from mining and mill reconciliation. The mine produced 503 000 ounces of gold in 2001. Exploration at the mine is targeting HGZ-type ore formation within basalts associated with the intersections of fluid pathways and folded ultramafic rocks, as well as other targets."

Jan 1, 2001

By W. G. Jeffery

"The mining and mineral industries have been, and remain, a major component of the Canadian economy. There are approximately 560 producing mining establishments of which there are some 130 metal mines and an equal number of non-metal mines, the balance being quarries for stone, sand and gravel. For 17 metals and minerals, Canada ranks within the top five as a world producer. There are 29 metallurgical plants. Employment in mining, smelting and refining was about 150000 in 1990. Mineral production, including coal, is about $20 billion. Exports up to the metal stage amount to $15 billion providing a positive trade balance of some $10 billion.The producing industry has a wide diversity of products. The companies range from small single mining operations to large multinationals. In terms of technology the industry has always been in the forefront of cost-effective practice, either using home-grown innovation or freely importing technology from around the world,The Mining Industry Technology Council (MITEC) makes an annual survey of the exploration and R&D expenditures of the senior mining industry that is the mining companies that are involved in mineral production from their existing mines. It does not include those companies solely involved in exploration using funds raised through equity sales.Table 1 shows the actual R&D and exploration expenditures as a per cent of sales. R&D shows a rising trend since 1988although the drop in value of output due to lower prices must be recognized as contributing to the increase. The point about this compilation is that the mining industry re-invests some 4070 of its sales in both exploration and R&D in order to sustain itself. Exploration for the renewal of metal inventories for future mining is a process unique to mining. It is not classified as R&D, and the necessity for this investment goes unrecognized by those who state that the industry does not do enough R&D."

Jan 1, 1993

By K Byrne, W. Hawker

The average grade of copper concentrate is steadily declining, forcing the industry to turn to lower grade and metallurgically challenging orebodies. When faced with a low grade, challenging ore, mining companies are often forced to choose between high recovery at low grade or low recovery at high grade. Hydrometallurgical processing of copper concentrates using metathesis reactions, which replace iron with copper in copper-iron sulphide minerals and increase the copper to sulphur ratio in copper sulphide minerals, provide an opportunity to upgrade copper concentrates and potentially allow high copper recovery for a high grade concentrate. Factors such as concentrate mineralogy, reaction time and temperature, and the concentrations of copper, chloride and acid in solution are reported to affect the reaction extent and mineral phases formed by metathesis. In this paper, a copper concentrate has been studied over a wide range of conditions to investigate the influence of these key parameters on the extent of copper metathesis reactions and product phases formed. Solution and solid phases are assayed with the main mineral phases identified by Quantitative X-Ray Diffraction. INTRODUCTION The minerals present in copper deposits determine the prospective processing options either: pyrometallurgical or hydrometallurgical. For copper oxide ores, copper is typically present as oxides, carbonate, chlorides, silicates and sulphates. These minerals are readily solubilised in acid and are usually treated through hydrometallurgical processes. The typical process route for copper oxides is to leach copper into aqueous solution, purify and upgrade the solution phase through solvent extraction and then recover copper as metal by electrowinning (Davenport, King, Schlesinger, & Biswas, 2002). Copper sulphide deposits may contain a multitude of copper bearing minerals, including chalcopyrite, bornite, enargite, covellite, digenite and chalcocite. The copper ore grade and treatment options are affected by the mineral type and distribution. Sulphide ores are typically treated through comminution and mineral flotation to form concentrates, followed by pyrometallurgical smelting. Hydrometallurgy can also be used to process sulphides depending on the mineralogy and impurity levels (Davenport et al., 2002). The trend of decreasing copper grade with increasing impurity levels are common across the mining industry and pose future challenges to copper processing. This trend has prompted research into hydrometallurgical options for upgrading copper concentrates. One promising hydrometallurgical option is using metathesis reactions. Metathesis reactions, sometimes also called double replacement or displacement reactions, are chemical processes involving the exchange of bonds between two chemical compounds or species. In this case, the metathesis reactions involve copper in solution exchanging with cations in the solid sulphide concentrate. The driving force for copper sulphide metathesis is the relative affinity of the exchanging cation elements for sulphide. Based on sulphide precipitation diagrams, the expected order of affinity for sulphide should be Hg2+ > Ag+ > Cu+ > Cu2+ > Bi3+ > Cd2+ > Pb2+ > Sn2+ > Zn2+ > Co2+ > Ni2+ > Fe2+ > Mn2+ (Monhemius, 1977). Hence, copper metathesis reactions are capable of increasing copper content and removing impurities such as iron, nickel, zinc and lead from copper concentrates.

Jan 1, 2019

By Richard Q. Fox, Joe L. Pinson

This paper provides guidelines jo1• analyzing and selecting electric power demand controlled. Error calculations, load selections and timing criteria are identified as the three key functions which affect the suitability of a demand controller for any particular application. The advantages of simulating the demand control application on a computer are described, and applications of a demand controller to an iron ore concentrator and a copper refinery are shown. Finally, the paper studies the return on investment for a demand controller.

Jan 1, 1976

By Roy Sage

Overview ? History ? background to current programs ? Kyoto status ? Support for technology development ? Support for GHG reduction ? Sources of information History ? 1988 - Toronto Conference - The Changing Atmosphere ? Proposed target ? CO2 levels reduced to 20% of 1988 levels by the year 2005 ? 1992 - Canada signed Framework Convention on Climate Change at the UN Conference on Environment and Development in Rio de Janeiro in June 1992 ? Canada launched the National Action Plan on Climate Change ? Kyoto protocol adopted in principle in 1997

Nov 1, 2002

By G. L. Spence

Prevention of cuprous and cupric oxide formation on stored ETP copper rod is a major concern for copper rod and wire producers. During normal storage periods copper oxide layers can increase from less then 100 A to more then 1000 A exceeding ASTM specifications and discoloring the rod surface. Various types of corrosion inhibitors are tested and compared in effectiveness for prevention of copper oxide formation on stored copper rod. Aromatic triazole compounds are also compared to a non-azole containing compound.

Jan 1, 2007

By H. Ito, T. Takasu

A leaching process for recycling small car motor scraps dismantled from End- of - Life -Vehicles (ELV) was investigated using waste pickling acid in steel work. Steel parts of mortar scraps were leached by waste pickling acid and Cu wire was recovered as pure Cu in the process. Pickling acid solution after leaching could be recycled in an ordinary process for waste pickling acid solution. High grade FeSO4 agent could be produced using H2SO4 as a pickling solution.

Jan 1, 2004

By L. M. Guayacán-Carrillo, G. Armand, A. Noiret, D. Seyedi, S. Ghabezloo, J. Sulem

"The main purpose of this paper is to analyze the convergence measurements in a drift excavated in the Callovo-Oxfordian claystone. The drift axis is in the direction of the major principal horizontal stress whereas the stress state is quasi-isotropic in the drift’s section. The initial geometry of the drift being circular, the anisotropic character of the deformation is taken into account by assuming that the drift shape evolves in an elliptical shape. The convergence measurement data on six different points around the drift are analyzed to identify the main axes of the deformation ellipse, following the methodology proposed by Vu et al. (2013, Rock Mech Rock Eng, 46, 231-246). Then, using the semi-empirical law proposed by Sulem et al. (1987, Int J Rock Mech Min Sci, 24, 145–154), the convergence evolution is fitted independently for each axis of the ellipse. This method permits to distinguish two effects: the face advance effect and the time-dependent behavior of the ground. The results for the two directions of the ellipse axes show very close values for the parameters describing the time-dependent properties of the ground, the distance of influence of the face, and the extension of the decompressed zone around the gallery. Such model can provide valuable insights for predictions of the convergence evolution in the long-term. INTRODUCTIONDeep disposal of radioactive waste has been studied in France for more than two decades. The French National Radioactive Waste Management Agency (Andra) began in 2000 the construction of an Underground Research Laboratory (URL) with the main goal of demonstrating the feasibility of a geological repository in Callovo-Oxfordian claystone. Several research programs have taken place to improve the knowledge of the rock properties and its response to the excavation progress. The optimization of supports design for long-term behavior is an important point to develop. A network of experimental drifts has been constructed with variations on: excavation method, structure geometry, supports system and orientations with respect to in-situ principal stresses’ directions. In each drift different sections have been instrumented to monitor the convergence evolution and the rock deformation. Continuous monitoring of the excavated zone around the drifts revealed the development of a fractured zone (extensional and shear fractures) induced by the excavation. The extent of this fractured zone depends on both the drift orientation and the in-situ stress field (Armand et al., 2014). Indeed, the fractures distribution has an important influence on the convergence of the drifts."

Jan 1, 2015

By E. H. Henderson

MR. R. V. NEILY stated that he had at one time operated at Goldenville. The practice and results are much the same now as in the olden days. Inside plates were then found to be a source of trouble and had been removed. At the Libbey mine, Queen's county, the sulphides carried considerable gold, and $45.00 to $60.00 per ton had been recovered from the concentrates by roasting and chlorinating. Later, concentrates were treated with bromocyanide. Following that practice, a cyanide leaching plant was installed, which did not require concentration of the tailings. Cyanidation brought a recovery of around 95 per cent, with but $300 worth of plant. In Nova Scotia, the ore of each locality presents an individual problem of its own as to treatment required. Ma. W. B. Timm stated that, in the majority of Nova Scotia gold ores, more than 75 per cent of the gold content is free-milling and, naturally, stamps are most efficient for collecting and amalgamating this gold. In Ontario and the West, they had got away from stamps, and perhaps the main reason was that the supply of battery-men, who came from Nova Scotia, had died off. Ball-mills had been installed, which required smaller space and handled large tonnage, even though, as far as amalgamation goes, the stamps were probably more efficient. If concentration is to be done, ore from stamps is usually in better shape for recovery in passing over the tables, as there is no slime. With the ball-mill, flotation is necessary. The better practice, undoubtedly, is to take out what gold is possible before it is all smashed up, as in the ball-mill, though recent developments in the ball-mill make it possible to trap and take coarse gold directly from the mill. In this way, cyanidation is speeded-up, due to saving of the time the coarse gold would take before going into solution. PROFESSOR A. E. FLYNN found it unusual in these days to read anything in favour of the stamp mill, and thanked Mr. Henderson for the excellent paper in which he upholds the stamps and backs his opinion with facts from actual operations. For the typical Nova Scotia ore, containing coarse gold, stamps are un¬excelled. It used to be said that the virtue of stamps is that they brighten the gold for amalgamation. Although this saying is almost classical, it is not true, for gold is never brighter than in the native, untouched state. Any hammering that gold gets makes it more difficult to amalgamate.

Jan 1, 1935

By T. Crivits, I. Bellemans, V. Cnockaert, K. Verbeken

It is well known that slag foaming can significantly complicate copper smelting processes. This is especially true for unpredictable events that generate large amounts of slag foam during a small period of time. These events are here referred to as eruptions and are typical for certain types of liquid bath furnaces such as modern top submerged lance (TSL) furnaces. A few authors already made the link between over- oxidation of the slag phase and slag foaming. In this work, the mechanism is studied in more detail and explained using the smelter chemistry and the behaviour of dynamic foam formation. Finally, the most influential parameters on the foaming behaviour of the process are presented. INTRODUCTION Copper remains one of the most important metals used in our modern society. In 2017, the annual amount of copper produced worldwide was about 23.5 million metric tons. This makes copper the third most produced metal in the world after steel and aluminium. The majority of this copper was produced by copper smelting, about 19 million metric tons, both from primary concentrate and secondary feed material as reported in ICSG’s World Copper Factbook 2018. In the past, copper smelting was mainly performed using Flash smelting, a technology developed before 1949 (Kojo, Jokilaakso & Hanniala, 2000). Nowadays, this type of smelter is being complemented by other smelter types such as ISASMELT and Ausmelt technologies. These are two types op smelter furnaces, based on the concept of a top submerged lance (TSL) furnace. These two technologies were both commercialized around 1990 (Arthur & Hunt, 2005). It is estimated by Wang et al. (2016) that at this time, both flash and TSL smelters contribute equally to the total amount of annually smelted copper. Flash smelting stays the most important technology for extracting copper from primary sources. TSL furnaces, on the other hand, are more suited than Flash smelters for the recovery of copper from secondary materials. This is because of the different ways that the feed material is inserted in both furnaces. In Flash smelters, the ore and fluxes needs to be fine and completely dry in order to be able to blow the mixture inside the burner area of the furnace. The feed material for TSL smelters show less constrains concerning humidity and particle size. The material is dropped from the top inside the molten bath. As a result, a more complex and flexible feed stream can be processed using TSL smelting (Wood, Hoang & Hughes, 2017). This feature will become more important in the future as primary copper sources gets more scarce and the need for a fully sustainable material cycle increases.

Jan 1, 2019

By Ferri P. Hassani, Riadh Bouzaïene

"Selected methods of pressure loss predictions in horizontal slurry flow in pipelines are presented. For a given combination of flow velocity, solids concentration and particle size, the slurry and its flow conditions are described, and an appropriate method of pressure loss prediction is outlined. The wide range of conditions treated in this paper may be found in practice in areas varying from the hydraulic transport of low concentration slurries to dense-phase conveying of paste backfill in underground mines.IntroductionThe hydraulic conveying of solid particles in pipelines is a major component of the mining and mineral processing industry. Whether the objective is to transport ore to the processing plant or to make use of mill tailing as backfill material; the need for well designed, economical hydraulic conveying systems is recognized.The contribution of this paper is part of an on-going research program at McGill University involved in optimizing and developing techniques for total mine waste disposal. One of the main concerns in the conveying of solid-liquid mixtures is the prior knowledge of the pumping power input required. This energy requirement is directly proportional to the pressure losses incurred in the pipeline system. Understanding the sources of such pressure losses and predicting their magnitudes should enable the system designer to make informed decisions regarding the optimum mode of hydraulic transportation commensurate with the over-all requirements of the operation.This paper is an attempt to classify pressure loss prediction methods encountered in the literature for solid-liquid mixtures. In spite of the large number of publications spanning thirty years of research in the field of slurry transportation, it is sometimes difficult to correctly identify the appropriate methods applicable to a given situation. This is partly due to the inherent complexity of the mechanics of slurry flow and the ensuing uncertainty about the nature of the flow regime under investigation.Our approach is to use three fundamental parameters, namely: flow velocity, solids concentration and particle size (for solid particles with a given density) to characterize the slurry and the flow conditions, and to match them with an adequate pressure loss prediction method. For each combination of flow velocity, solids concentration and particle size, a description of the most likely prevalent flow conditions and some known methods of dealing with them will be presented. Qualitative definitions of ""high"" and ""low"" magnitudes of the aforementioned parameters will be given as a general guide to the classification scheme presented in this paper."

Jan 1, 1992

By Ben Cottrell

In this paper technical drilling is referred to as the process of collecting engineering and metallurgical parameters for subsequent mine design considerations. Throughout the development of a mineral exploration property there are various opportunities to ?piggy-back? technical drilling onto the routine exploration drilling process, helping to reduce future costs and delays associated with re-drilling and missing information. This article is written from the engineers and metallurgists point of view, to outline some best practices for exploration borehole planning and technical data collection requirements.

Aug 1, 2013

Presentation Overview ?WRDC Purpose and Activities ?Women in Trades, Technology and Operations (TTO) Occupations ?Factors in Successful Recruitment / Retention of women (VBNC) ?Recruitment and Retention Strategies ?Conclusion Women in Resource Development Committee (WRDC) ?Incorporated in 1999 as a Not for Profit Organization ?Based in Newfoundland and Labrador ?Works to Increase the Participation of Women in Natural Resource Industries ?Research (Using Gender-Based Analysis) ?Career Exploration Programs for Women and Girls ?Outreach and Advocacy ?Policy Development ?Public Awareness and Education ?Gender Sensitivity Training ?WRDC Educational Resource Centre

May 1, 2006

By Jaroslaw W. Drelich

Despite the success of DLVO and extended-DLVO models that have been developed for homogeneous and smooth surfaces, a vast majority of practical surfaces encountered in mineral ore beneficiation are typically rough at various scales; they are also typically heterogeneous. The interactions of gas bubbles with particles having rough and heterogeneous surfaces are much more complex than the commonly used DLVO or extended-DLVO models predict. The effects of surface roughness on flotation and colloidal interactions have been reported many times in the past, although a clear understanding of their origins has been lacking. To explain differences in colloidal interactions for spherical hydrophobic particles, a theoretical analysis of the interaction potential was carried out for a model rough particle interacting with a bubble surface in an electrolyte solution in this study. The attractive hydrophobic interaction potential was added to repulsive retarded van der Waals and repulsive electrical double layer interaction potentials. The rough microscopic particles were modeled as spheres decorated with nano-sized asperities. Parameters that reflect common flotation separation systems were selected for testing this theoretical model and computation of the energy barrier applicable to particle – flat bubble surface interactions. It was found that hydrophobic asperities with the height of only several nanometers can reduce the repulsive interaction energy by an order of magnitude. Theoretical analysis also reveals that surface coverage of microscopic particles by nano-sized asperities is important as well. The findings of this research suggest that manipulating and engineering the particle surface topography could lead to better control over flotation separation.

Jan 1, 2016

By F. P. Hassani, J. F. Boily, A. M. O. Mohamed, M. Hossein

The optimal geochemical parameters required to form ellringite in a lime-remediated site have been investigated with the use of thermodynamic modelling. The speciation of sulphate and 10 metals analyzed in samples of a mine tailing from northern Quebec was calculated with a computer model. The model also includes calcium, which would result from the addition of lime to the system. Two speciation calculations were done. The first one is a hypothetical speciation before the onset of precipitation and was used to devise the stability fields of minerals susceptible of forming in high pHs. The stability fields were determined by building activity ratio diagrams with sulphate, aluminum and calcium species concentrations for pHs ranging from 4 to 14. The investigation was carried out for a 25°C solution with an ionic strength less than 0.12. Thermodynamics predict that an optimal stability field for ettringite in the mine tailing samples containing 10-3 mol/L SO4-2,10-2 mol/L of AI(OH)4 requires at least 10-2mol/L of Ca+2 and a pH larger than 11.6. The sulphate contents of the mine tailing samples, however, limit the precipitation of ettringite and monosulphate could be an end-precipitate. The second speciation is in equilibrium with precipitates and provides information on the speciation of the residual metals. If ellringite could be precipitated as a stable form, it could serve as a sorptive agent for residual metals, and, due to its binding properties, consolidate tailings.

Jan 1, 1995

By J. Roth

"While not taking issue with the general thesis expressed in Dr. Ridge's analysis of the role of genetic concepts versus observational data in ore exploration (Ridge, 1983), the criticism could be offered that the author tends to slight the importance of conceptual (i.e. theoretical) models in mineral exploration.As a general rule, observational data in science lacks significance and utility without a theoretical construct to organize those observations. Theory in turn dictates what observations are made-and which ones are judged important. Thus, for example, prior to the elaboration-and acceptance- of the current model for volcanogenic base metal deposits, the structural aspect s of these deposits were most closely observed and studied by explorationists. The nature of the enclosing rocks and any attendant alteration was given minimal attention, and certainly didn't figure prominently as an exploration guide.Similarly, the importance of alteration features to exploration for porphyry copper-molybdenum deposits was only perceived when a theoretical model was developed to account for these aspects. Indeed, many of these porphyry copper deposits were regarded as epigenetic vein deposits by geologists of an earlier era observing and examining on a different physical scale-and with a different theoretical bias.In constructing and evaluating such conceptual models, explorationists primarily rely on observation data and proximate associations; speculative thoughts as to ultimate provenance or crustal evolution clearly play a subordinate role, as Dr. Ridge argues. This, however, should not obscure the fact that concepts and theories do indeed exert a major influence in mineral exploration."

Jan 1, 1983