Search Documents

By P. J. Mackey, Elsie Kossatz

The small town of Bruce Mines lies a few miles east of Sault Ste. Marie, Ontario on the north shore of Lake Huron. This was the site of the first copper mine. This copper smelter used a reverberatory furnace, based on the Welsh process, and operated in the period of 1849 to 1850, when the plant was destroyed by fire. During the period of 1850 to about 1869, crushed and sorted ore was shipped to England and later to the United States. In 1869, a roastleach plant, based on the Henderson Process, was constructed at Bruce Mines and was operated until about 1872. This short article describes the early development of this historic operation. Although the rich copper ore found in the vicinity of Bruce Mines was known to the Indians, its discovery in or about 184 7 was credited to Mr. Keating, who named the area Bruce in honour of Lord Elgin (James Bruce), Canada's Governor General. In 1848, the property was acquired by the Montreal Mining Company for 40 000 pounds sterling and the company immediately sent a small party to investigate the deposit. The party sank a shaft on a lode within a hundred yards of the lake and also reported two adjacent lodes farther inland, which were left undeveloped until the turn of the century. Initially, the foundation of the headframe and hoist was built above the frost line and when the machinery was set in motion it collapsed. Eventually, the shaft was to reach a depth of 300 feet. By 1849, the property was well established and the small settlement consisted of 77 miners, 65 labourers, 4 boys, 11 tradesmen, including blacksmiths and carpenters, 2 mining captains, 1 engineer, 2 clerks and 1 superintendent. The community, including the workers' families, numbered about 250.

Jan 1, 1999

By E. E. Mueser

As Mr. Lundberg has already ably covered the theory of various methods of electrical prospecting, I shall confine my remarks to a consideration of the features which must obtain in an electrical prospecting method in order that it may be useful from a practical standpoint. These remarks I shall make with particular reference to the Elbof method. The successful application of all these methods rests, in the first place, upon the possibility of correlating theory, or empirically established facts, with the field data. Their practical usefulness, however, requires that the technique of making the field observations, and the procedure itself, be such that the method may be applied to large areas, under normal average conditions. The method, therefore, should not involve excessive preliminary labour costs to prepare the ground for actual prospecting work, nor should the prospecting work itself be so slow that its cost, when applied to extensive areas, becomes prohibitive. Moreover, it should be possible to apply the method even under difficult terrain conditions, such as rough topography and dense vegetation. It may be said of most of the methods referred to in the preceding paper, that, while they are interesting and theoretically sound, they fail to meet such practical requirements as I have outlined.

Jan 1, 1926

By E. R. Landry

This paper reviews the current state of electric furnace technology, with emphasis on some of the more recent developments. A large section of the paper is devoted to the use of increasingly high power inputs by arc furnace operators. Operating practices are then covered, including some of the newer techniques which have been tried.

Jan 1, 1967

By Yves Gagnon, Nicole Gauthier, Daniel Kelly, Michel Rocheleau

"The Larder Lake-Cadillac Tectonic Zone in Rouyn-Beauchastel area (a 20 km long segment) contains distinct lithotectonic units bounded by artastomosing or sub-parallel shear zones. The gold deposits in the area are located within highly strained portions of E-W striking shear zones. The ore-zones are structurally controlled disseminated and vein-type lodes. They are spatially related either to megascopic z-shaped folds which refold E-W shears, or to areas of intersection between E-W shear zones and late NE-striking faults. Several ore bodies are enclosed within ultramafic rock units or at their contacts with adjacent units. All the lenses are elongated down dip and distributed, both loterally and vertically, ""en echelon"" . The ore zones tend to decrease in size and number away from the hinge zone of the megascopic z-shaped folds.Two main styles of mineralization are recognized at the Astoria deposit and at for most of the deposits in the Rouyn-Beauchastel segments a discontinuous ""Carbonate Ore"" and a more continuous, albitic sulphide-bearing ""Flow Ore"" (terminology used at the Kerr Addison mine).The typical ""Carbonate Ore"" zones are found within strongly arbonatized blocks bounded by conjugate late NE or NNW-striking fralls. The carbonatized blocks display features characteristic of llrittle to brittle-ductile deformation developed in shear zone system. Vein systems in the ""Carbonate Ore"" occur within shear fractures(D R)tension fractures (T), or within brecciated rocks adjacent to NS llrilcing faults. The ""Carbonate Ore"" zones are displaced by numer IU lole E-W, NNE, NW and N-S faults.The ""Flow Ore"" zones are found within predominantly ductile portions of E-W shear zones. The sulphide mineralization is finely disseminated and regularly distributed within mylonitic foliation or associated with veins and veinlets sub-parallel or oblique to the mylonitic foliation, in which case the mineralization is coarser grained. The gold mineralization is a late Archean event postdating the formation of the penetrative fabric, and synchronous with the end of the dextral oblique-slip motion."

Jan 1, 1990

By W. A. Padgham, J. A. Brophy

About 85 % of the 350 tonnes of gold produced by 25 mines in the onhwe t Territories (NWT) since 1935 has come from the Yellowknife-area mines, Con and Giant , which exploit shear zones in Archean mafic volcanic of the Slave Structural Province. Four percent of the total production has been from Archean iron formation-hosted depo its, mainly from Lupin Mine, which today produces more gold than Con and Giant combined and has been primarily responsible for the increase of WT gold output from 5 to 12 tonne per year since 1981. The remaining gold ha been won from the following deposit typesall but the last being in Archean rock : sedimentary-volcanic contact depo its uch a Discovery and Salmita (10 %); turbidite-hosted quartz-vein depo its uch a Camlaren and Ptarmigan (1%); Proterozoic deposits such as Shear Lake and Fox (1#) . All but I% of WT gold has come from the Archean Slave Structural Pro ince, which is also the premiere exploration area for gold deposit types that have yet to be productive in the NWT. These types include stratabound gold in mafic and in felsic volcanic rocks (eg. , at Indin Lake and Courageous Lake, respectively) as well as gold in plutonic rocks (eg. Anialik Gnei Complex). Deposits similar to those in the Slave have al o been found in the Archean Ennadai Belt of the Churchill Structural Province. In the Cordillera. there is potential for placer gold and for gold associated with Cretaceou intrusions.

Jan 1, 1986

By M. Sukhram

This paper presents a technique to determine the direction of velocity in liquid aluminum (Al) by measuring the temperature distribution within a cylindrical rod while it is inserted into the flow. The heating pattern of the rod is a result of the interaction of the thermal fields of the rod with the liquid Al. This interaction freezes aluminum onto the cylinder in a characteristic pattern and as a result the temperature response within the rod also follows a distinctive heating pattern. Monitoring the temperature within the cylindrical rod as a function of spatial and temporal coordinates, the direction of velocity can be inferred. Experimental research work involving liquid Al was conducted at the University of Toronto using the Revolving Liquid Metal Tank (RLMT). The RLMT is a resistance furnace which can hold up to 50kg of liquid Al. In this RLMT tangential velocities up to 0.35m1s can be generated. Experimental data for different superheat and magnitude of velocity demonstrate that the sensor records different heating patterns under different fluid flow conditions. Using the transient temperature information, the direction of velocity of the molten Al flow field can be detected.

Jan 1, 2011

By H. H. Gardner

Introduction The Greenhill mine of West Canadian Collieries, Limited, is on the Alberta side of the Crowsnest pass, twelve miles from the Alberta British Columbia boundary-line. Here, five coal seams of Lower Cretaceous age are found in the Kootenay formation. They outcrop on the north and south slopes of the valley, with strike approximately N.30°W., paralleling the main range of the Rocky mountains, and dip about 40 deg. westward. Of the five seams, only two, designated No. 1 and No. 2, have been worked to date. On the West Canadian Collieries property, No. 1 seam ranges in thickness from thirty feet to nil. Generally, it has a hard, strong conglomerate roof. No. 2 seam is separated from No. 1 by forty-five feet of shales and sandstones. It has a thickness of eight to thirty feet.

Jan 1, 1947

By Euler De Souza

"The uninterrupted operation of a ventilation system is critical to ensure the mine meets its scheduled production and, as important, is vital to the health and safety of all personnel working underground. Those operating the mine ventilation system must have fundamental engineering training in the art of fluid dynamics and have a good comprehension and control of the mine ventilation network. Ventilation management by untrained and inexperienced personnel may result in serious consequences when the system becomes ineffective. This paper shares observations and experiences pertinent to the occurrence of upset conditions as a result of the improper design and operation of mine ventilation systems. A series of real life case studies are presented to describe disruptions to mine ventilation systems and the gradual deterioration of system operational efficiencies leading to eventual failure. Special focus is given to mistakes made and on the resulting serious consequences. The case studies also demonstrate how each upset condition was resolved, permitting the mines to safely resume production activities.INTRODUCTIONThe ventilation of operating mines is a continuously changing and evolving system; upset conditions will occasionally occur, but should be promptly resolved in order for the system to function properly, according to design, and in compliance.Those designing, managing or operating the mine ventilation system must have pertinent training and have a good understanding of fundamental ventilation concepts to be able to devise and implement engineering solutions to day-to-day challenges. Realistically, the operator must also have extensive practical experience and be able to effectively apply operating procedures, design criteria and ‘best practices’. They must be able to, on a daily basis, evaluate the mine ventilation system, determine and locate any problems, understand the causes of each problem, find a solution, and promptly and efficiently correct those problems.Ten case studies are presented to demonstrate how fundamental design or operational mistakes can lead to adverse conditions or to catastrophic consequences, how detailed on-site engineering assessments can be employed and how simple, low cost, engineering solutions can be implemented to successfully resolve the issues and return the ventilation system to compliance, permitting the mines to safely resume production activities."

Jan 1, 2019

Mining companies around the globe have long struggled with the need to ensure that earth moving equipment is designed to be operated and maintained under all site conditions without causing harm to people. Incident and accident data from a range of sources clearly identify mining equipment related issues as major causal factors. One Australian source, the NSW Department of Primary Industries? International Mining Fatality Database Project Report (2008) noted that ?Approximately 77% of mining accidents resulting in a fatality have? involved equipment?. The largest number of fatalities were associated with trucks; the next with LHDs. Many of the technical advances in equipment design over the past few decades have not been matched by advances in the human factors design of mining equipment, resulting in a ?design vacuum? that must be filled prior to commissioning new equipment. This ?design vacuum? is generally filled by local dealers. They retrofit equipment according to customer requirements to mitigate risks that have not been designed out by the Original Equipment Manufacturer (OEM). Mining companies have been frustrated by lost time and additional costs associated with this need to retrofit ex-factory designs. Some companies have attempted to address the problem by negotiating company or site-wide ?solutions? to equipment designs, but this has not simplified or clarified the issue from the point of view of the equipment manufacturers. A number of mining companies operating in Australia first discussed the concept of a joint customer approach to improve the Human Factors design of earth moving equipment at the factory level in 2004. They agreed that a new approach to engaging with OEMs was needed; one that would define the ?Problem?, in other words, the basis of the risks, rather than dictate the ?Solution?. The Earth Moving Equipment Safety Round Table (EMESRT) was formally established in 2006 by six global mining companies to establish a process of engagement between Original Equipment Manufacturers (OEMs) and mining customers.

May 1, 2009

By James E. Rider

"Fractures in mine hoist drumshafts are rare. We know of no previously reported attempts to repair a fractured drumshaft; any feasible method would involve welding and the associated problems of distortion, crack formation and strength.In June 1984, a fracture was discovered in the drumshaft of the production hoist in the Teck Corporation, Lamaque Division Mine at Val d'Or, Quebec. Delivery time on a new shaft would have been at least six months. The shaft was repaired in ten days and the total out -of-service time was four weeks.This paper describes why the shaft failed, how it was repaired, and the special alignment procedures employed during re-installation to minimize stresses in the repaired area.IntroductionThe performance of a mine hoist drumshaft is absolutely critical to mine operation. An inoperable drumshaft means no hoist, which in turn means no production or mine operation.Fractures in mine hoist drumshafts are rare. Previously when they have occurred, no one has seriously considered attempting a repair because of problems involved. Any feasible method would involve welding, which raises several major problems - namely, metallurgical, alignment, and strength.In July 1984 this very situation occurred at the Teck Corporation, Lamaque Division Mine in Val d'Or, Quebec.It was recognized that a new shaft would take at least 6 months' fabrication and delivery time. However, having had some experience at repairing broken shafts in other machines under similarly desperate circumstances, and after due consideration, it was concluded that by applying the correct techniques and engaging the right expertise, it would be possible to perform a repair and have the mine back in operation within a month.Thanks to outstanding efforts by all, the repair was accomplished in ten days and total out-of-service-time was only four weeks. The causes of the failure were determined and the calculated stress levels confirmed by strain gauge measurement during operation.The success of this project was achieved by adhering rigorously to fundamental management and engineering principles."

Jan 1, 1988

By James E. Rider

"Fractures in mine hoist drumshafts are rare. We know of no previously reported attempts to repair a fractured drumshaft; any feasible method would involve welding and the associated problems of distortion, crack formation and strength.In June 1984, a fracture was discovered in the drumshaft of the production hoist in the Teck Corporation, Lamaque Division Mine at Val d'Or, Quebec. Delivery time on a new shaft would have been at least six months. The shaft was repaired in ten days and the total out -of-service time was four weeks.This paper describes why the shaft failed, how it was repaired, and the special alignment procedures employed during re-installation to minimize stresses in the repaired area.IntroductionThe performance of a mine hoist drumshaft is absolutely critical to mine operation. An inoperable drumshaft means no hoist, which in turn means no production or mine operation.Fractures in mine hoist drumshafts are rare. Previously when they have occurred, no one has seriously considered attempting a repair because of problems involved. Any feasible method would involve welding, which raises several major problems - namely, metallurgical, alignment, and strength.In July 1984 this very situation occurred at the Teck Corporation, Lamaque Division Mine in Val d'Or, Quebec.It was recognized that a new shaft would take at least 6 months' fabrication and delivery time. However, having had some experience at repairing broken shafts in other machines under similarly desperate circumstances, and after due consideration, it was concluded that by applying the correct techniques and engaging the right expertise, it would be possible to perform a repair and have the mine back in operation within a month.Thanks to outstanding efforts by all, the repair was accomplished in ten days and total out-of-service-time was only four weeks. The causes of the failure were determined and the calculated stress levels confirmed by strain gauge measurement during operation.The success of this project was achieved by adhering rigorously to fundamental management and engineering principles."

Jan 1, 1988

By Mikael Ramström

The IREDES Special Interest Group (SIG) for Drill rigs has been active since its inception at MineExpo 2000, in Las Vegas USA. The SIG for drill rigs is responsible for the development of a IREDES Drill rig profile. This includes the exchange of production planning, performance and quality reporting data between various kinds of drill rigs and the databases used by the operating mine. During year 2001 a first draft of the drill rigs profile was jointly prepared by drill rig suppliers, mining companies and third party suppliers and reviewed during several SIG meetings. In mid 2002 the profile was released for prototyping projects and since then, feed back received from these projects has been used as input to the first official IREDES release. LKAB and Atlas Copco decided in 2002 to start an IREDES prototyping project using the Simba L6C production drill rig as target equipment. The goal was to verify the drill rig profile and identify possible problems prior to the official release. This was done by implementing the IREDES prototype version in the LKAB?s production planning system and Simba rig control system. The Simba rig control system was designed to handle drill plan and logging information coming from the mine planning system. In parallel to this the mine production system was adapted for drill plan export and logging data import on IREDES format. This paper presents the most recent results of this prototyping project. Result from late 2002 show that the basic architecture of the drill rig profile works and that a common language for data exchange, IREDES will be a central issue for future mine automation. As a result from this and other IREDES prototyping projects the official IREDES release will be available in 2003. Soon after that release IREDES compliant products can be expected. This will include drill rigs and mine production planning systems.

May 1, 2003

By D. B. Nazzer

"ANY DISCUSSION of energy today is incomplete without consideration of nuclear energy. In the Maritimes, with plentiful supplies of coal, with relatively easy availabilty of imported oil brought in to the deepwater terminals, with future sources of large supplies of oil and gas anticipated from under our neighbouring continental shelf, and with the Fundy tides, you may question why nuclear energy should be considered. What follows may not give you a specific answer to that question, but it may provide a basis for better understanding. Energy from the sun, from hydraulic sources and from combustion has been available to man from prehistoric times, for thousands of years, but the most sophisticated source of energy, the actual conversion of matter into energy by man, has been developed entirely within the last one-third century, since the discovery of fission in 1939, and the application to generation of electric power has all been done within a generation or less. The pressure of military needs during and after the second world war was largely responsible for the speed of initial development, by funding and focussing the effort needed to develop the basic technology, and in particular materials. The U.S. defence program yielded, for example, the large-scale isotope separation processes for fissile U'35 and for heavy water. The nuclear submarine program yielded zircaloy, a key structural material for the core of the Canadian Candu type reactor."

Jan 1, 1972

By John D. Lupton

This paper will discuss the benefits and advantages of using 3D survey data in stope analysis. Obtaining detailed 3D survey data of underground mine progress and production is a challenge. It is almost impossible to ?see? around corners, underneath overhangs, or deep into dark, dusty, humid underground voids. Thus, valuable ore can remain permanently encased in backfill. Without the benefit of 3D survey data, underground mines have the difficult task of meeting grade quotas without the benefit of knowing exactly what has been mined. Lack of this data usually results in unfavorable month end Reconciliation factors, where grades must be adjusted to match grades assessed by the Mill.

Apr 1, 2005

By Eric D. Monrad

Supply chain simulation modeling is taking on a more prominent role in mining project planning and decision making. Transportation costs for the supply chain can form a significant component of the overall cost to provide product to the end customer. In recent years, computing power has increased, simulation software has advanced, and simulation specialists have become even better equipped to provide sophisticated analysis and recommendations. This has led to a virtuous cycle of owners expecting and supporting data-driven analytics, which drives further advancement. This paper discusses developments in supply chain planning and two case studies from recent simulation modeling analyses.

May 1, 2013

By T Salman

The construction and use of the B.E.T. (gas adsorption) apparatus is described. Examples are given for the determination of large and small surface areas using nitrogen and krypton. Introduction A NY study of the milling of ores from crushing to grinding, classification, and concentration and finally dewatering of the products involves solid particles which are either in contact with a gas or a liquid phase. The surface area of the solid and its characteristics constitute important parameters in all mineral dressing operations. The success of any particular operation is dependent on the interaction of the surface of the solid particles with the gas or the liquid phase. Particle size and specific surface (surface area per unit weight) continue to be important parameters in the flotation research associated with the adsorption of collector molecules or ions on mineral particles, as in the early years of mineral dressing research (1). In order to understand the mechanism of the flotation process, it is essential that the surface properties of the adsorbent be known.

Jan 1, 1965

By T. Patching

"MINING operations at the Star Key Mine provided an example of a small-scale prairie-type coal mine that employed several interesting procedures and achieved good productivity with low capital expenditures. The mine was located about 11 miles north of the city of Edmonton, on the north side of the Sturgeon River valley. It opened in 1945 and operated until 1979. Output in the winters reached about 500 tons a day in the late 1940s, but in the spring and summer periods activity was usually limited to only servicing and development work. In the later years of the mine's life sales fell to less than 100 tons per day. Most of its output was bought for domestic use in furnaces and stoves so production of large sizes was desired. A modest market for stoker coal did exist for a time. Screenings (-5 / 8 in.) were sold to the city's power plant until it converted to natural gas and were also used for thawing frozen ground for work on pipelines. These markets were comparatively small and the small sizes did not command as high a price as did the larger sizes. However the extension of natural gas services to rural markets cut into the domestic heating market and finally led to closure of the mine. The coal was strong when freshly mined, but because of its high inherent moisture content, about 25%, it did not store well on surface but tended to disintegrate. It was of subbituminous Crank with a heating value of about 8000 Btu per pound and burned with a clean flame. The seam mined was in the Edmonton Formation, of Upper Cretaceous age, at a depth of 60 to 80 ft below the surface. The seam in the mine area was about 11 feet in thickness but thinned gradually to the north and south and split to the west (1). It was approximately horizontal but gentle rolls in the floor of several feet in height necessitated brushing in places to produce suitable haulage grades. The floor material was of bone and clay, overlying a thin layer of coal. Above the seam there were only a few feet of mudstones and weak sandy shales while the remainder of the overburden was clay and unconsolidated glacial till and surface soil. Because of the soft floor and weak roof material the miners usually left about a foot of coal in the floor to provide a firm working surface and about a foot of coal above the rooms and two feet of coal above the entries to provide a competent roof."

Jan 1, 1985

By A. Kobzhanov, S. Saparova, S. Brochot, D. A. Mango

KATCO (an ORANO Mining and Kazatomprom joint venture) is the largest in-situ leach uranium mining operation in the world, exploiting the Muyunkum and Tortkuduk uranium deposits in southern Kazakhstan. After extraction from the deposits, uranium is then transported via a hydraulic network to be purified in three processing plants located near these deposits. Within KATCO, with the support of ORANO Mining and CASPEO, in 2018 and 2019, a large project that had as its main objective to improve the uranium accounting system was implemented. The objective of this paper is to describe this project and all the changes that it entailed. At KATCO plants, a black-box approach was previously used for uranium accounting. However, it is recommended to use all the available measurements and to deploy a data reconciliation model (between well-fields and plant) as the reconciliation uncertainty is overall lower and it provides a more accurate uranium balance. During the deployment of this project, the rules and algorithms to generate the uranium accounting report, the associated flow diagrams (for uranium accounting), the streams, units of operation, stocks, reporting and Key Performance Indicators calculation rules were re-defined.

Jan 1, 2020

By Mark Rantapaa

Measurable improvements in throughput have been documented at Barrick Goldstrike due to increased ore fragmentation through efficient drilling and blasting techniques. A decrease in throughput at the Autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the Open Pit and Process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of actually improving throughput in future years, despite the projected harder ores. A series of tests were conducted to determine if adjustments to drilling and blasting could positively influence throughput. Better fragmentation and a subsequent increase in mill throughput were achieved through the use of: 1) Electronic caps for more precision and flexibility, as well as for allowing extremely fast shots. 2) Explosives with a higher velocity of detonation (VOD), to provide for improved shock energy. 3) Improved distribution of the explosives by decreasing pattern spacing. Early tests indicated a significant increase in throughput when processing identified harder ore. It is anticipated that the total process throughput (hard and soft ore) will increase by six tph in 2003 due to the improved fragmentation of the hard ore. Barrick Goldstrike?s D2M initiative includes roaster ?hard ore? (BWI >17), as well as autoclave ?hard ore? (BWI >15). Approximately six million tons of D2M material is expected be shot in 2003, a relatively small amount compared to the 150 million tons to be mined. The benefit of additional ounces produced should far outweigh the additional drilling and blasting costs.

May 1, 2003

By Simon Weixiao Sun

Conventionally, carbon steel has been the primary material for salt mine headframe construction, protected by specialty paint layers to prevent corrosion. These layers require meticulous QA/QC during fabrication and erection, and the top UV protection layer typically loses effectiveness after an average of 10 years, necessitating ongoing maintenance. As headframes age, significant structural repairs are often required. Alternatively, stainless steel can eliminate corrosion concerns, though its high initial cost has limited its use in headframe design. However, when factoring in long-term maintenance costs, a 'maintenance-free' stainless steel headframe can be an attractive option for stakeholders. This paper compares the structural performance and economic considerations of painted carbon steel and stainless steel headframes, including initial capital and long-term maintenance costs. Additionally, it explores a hybrid approach, strategically using carbon steel in low-contamination areas to reduce initial costs and significantly minimize future maintenance efforts.

May 4, 2025