Search Documents

By F. Richards

"The property of the Cariboo Gold Quartz Mining Company; Limited; is in the Wells-Barkerville district of Cariboo mining division. It consists of a group of 106 Crown granted mineral claims and fractions; and extends for over 6 miles along what is termed the Barkerville gold belt. The main portal and mine camp are half a mile south of Wells; which lies at the northeast end of Jack of Clubs lake and is reached by a 55-mile motor road from Quesnel; the northern terminus of the Pacific Great Eastern railway.Gold-bearing quartz veins were discovered on the surface in various parts of the property by different prospectors as far back as 1877, but the work that led to the formation of the present company was performed by Al Sanders in the year 1926. Sanders dug trenches and drove small adits on quartz veins containing gold above what is now known as the Sanders zone. Very little underground work has been done beneath the earliest known discovery-the B.C. vein. The Cariboo Gold Quartz Mining Company was formed in the autumn of 1926. The total production of gold from its beginning in 1933 to the end of 1944 has been as follows:"

Jan 1, 1954

By T. L. Tanton

"The New Helen mine is 12 miles east of Michipicoten harbour on lake Superior. It is 2 miles east of Wawa station, on the Algoma Central railway, with which it is connected by a spur line railway and a highway.The mine was discovered by Ben Boyer in 1898 during the gold rush near Wawa lake, Ontario. The original discovery was of solid hematite ore extending to a height of 100 feet on a hill rising abruptly on the east side of Boyer lake. The property was acquired by the Algoma Steel Corporation and mining was commenced in 1899. The first iron ore was shipped in 1900. The mine was operated until 1918 when the hematite became exhausted at a depth of 800 feet below Boyer Lake level.Drilling at the Helen mine, after 1910, revealed a large body of siderite both below and to the east of the hematite. By 1913, the body was known to be about 200 feet wide, 3,000 feet long, and at least 2,200 feet deep. In this there was estimated to be 100,000,000 tons of proved and probable siderite ore. An adit was driven into this body in 1917, and in 1918 work was suspended. In 1937 the Algoma Steel Corporation proceeded with the development of the New Helen mine by open-cut mining, and the beneficiation of the ore by sintering. Production commenced in 1939 and has since been maintained at the rate of approximately 500,000 tons a year.From 1900 to 1918, inclusive, the total production from the Helen mine was 2,823,369 tons of hematite ore and 51,930 tons of pyrite. From 1939 to the end of 1945 the total production from the New Helen mine was 3,921,455 gross tons of siderite ore.GEOLOGYThe Helen property is underlain by rocks of Precambrian age. For general description, and a statement on the structure of the iron deposits, the map-units are those shown in Fig. 1.The oldest rocks occur in a complex that lies north and south of an east-west trending zone, 1 ½ miles long and ¼ mile wide, in which the iron deposits occur. That part of the complex lying south of the iron deposits includes small masses of altered conglomerate and slate, and greenstones and pyroclastics. Other fairly abundant rocks are sericitic, chloritic, ottrelitic, and carbonatized schists of doubtful origin, and almost massive metamorphic rocks in which a development of carbonate, ottrelite, quartz, and other minerals has obscured a pre-existing schistose structure. Felsite and quartz porphyry are· prominently exposed south of the iron deposits."

Jan 1, 1954

By R. Burnette

Gold has been mined from a variety of deposit types that range in age from Archaean to Recent. The large variability in the geological settings of the gold deposits implies transport and concentration of gold by magnetic, hydrothermal and sedimentary processes. The factors that control the concentration of gold at certain sites and the grade estimation thereof remain major topics of debate. Due to the complex nature of the Witwatersrand Basin a mineralogical study, including mineralogical, petrographic and geochemical investigation was launched on TauTona Mine in order to characterize the various reef facies. The aim of the investigation was to determine if a correlation could be found between macroscopic characteristics of the reef, hanging wall and footwall, and the microscopic nature of the ore (especially gold grade). Petrograpgic and mineralogical results indicate that a correlation exist between gold, detrital and hydrothermal sulphides, uraninite, carbon, detrital heavyminerals and phyllosilicates. No correlation exist between gold and Mg, Fe or S. It appears that clast supported reef is of higher wade than matrix supported, but more work is suggested. No correlation exists between reef thickness and grade. The reef samples had the lowest phyllosilicate content compared to the hanging wall and footwall samples with pyrophyllite the most dominant. All of the correlations diagrams showed significant scatter and suggests a multi- factorial mineralization model. Gold distribution is also controlled by sedimentary features and thus it is not possible to select a single model for the formation and distribution of gold. It is evident that both sedimentary and hydrothermal factors influenced the mineralization and gold distribution on TauTona mine. It is thus essential that all related theories be incorporated in the development of a grade prediction model.

Jan 1, 2011

By Franc R. Joubin, Donald H. James

"The Property of Rix Athabasca Uranium Mines Limited is in the Beaverlodge area of northwestern Saskatchewan. The mine is 7 miles by road north from the Lake Athabasca port of Bushell which is 250 miles north by aircraft or boat from railhead at Waterways, Alberta.The Rix property is a portion of the former DD 1 concession, obtained in 1949 from the government of Saskatchewan when private prospecting for uranium became permissible. The concession was prospected in detail during the 1950 and 1951 field seasons and a great many radioactive show-ings were discovered. Development and drilling were concentrated in two and later three of these areas, and by late 1952 enough ore had been indicated in the Leonard series and ""Smitty"" zone to justify underground development by adit-drift and shaft respectively.Four hundred feet of drift development on the Leonard No. 1 vein and the sinking of a two-level vertical shaft with related lateral development on the Smitty zone were completed in 1953. In April 1954 the Smitty section was placed in production at a rate averaging 100 tons per day, thereupon becoming the first privately owned post-war uranium producer in Canada. The ore is shipped for processing 12 miles by truck to the mill of Eldorado Mining and Refining Limited.Until recently all of the Company's production was drawn from the Smitty orebody. In April, 1955, ore production commenced from the faulted west extension of the Smitty structure, known as the Rix 62 zone, and from the Leonard No. 1 vein.The Smitty orebody (see Figure 2) is an intensely brecciated lenticular zone bordering both sides of the Smitty fault. The breccia areas are irregularly mineralized with pitchblende, very sparse galena, and pyrite in a gangue of feldspar, chlorite, calcite, and silica, all thoroughly soaked with fine-grained hematite to produce the locally-called ""red alteration"".Tenor of the ore currently being mined is classified information. The average grade estimated, prior to production, was 0.20 per cent (4.0 lbs.) U308 per ton."

Jan 1, 1949

By Amin Saravari, Jamal Jafari, Abbas Sam

"The fourth concentrate production plant includes the comminution systems and the medium-low intensity magnetic separators (LIMS). Based on different conditions, two types of materials are fed into the plant. Type A: 70% of mine ore and 30% of reject materials from magnetite plant and type B: 100% of mine ore. The goal of the present study was to increase the iron grade and the blain number with low sulfur content in final concentrate as the pellet feed. An appropriate pellet feed should have more than 67% of iron, less than 0.1% of sulfur and a Blain number of more than 1800 cm2/g. The Fe, S and Blain no. amounts for the present concentrate are 66.6%, 0.95%, and 500 cm2/g (feed type:A) and 67.8%, 2.3%, and 450 cm2/g (feed type: B), respectively. In this research, the plant improvement efficiency was evaluated by changing the feed particle size distribution and using the flotation system. Laboratory experiments were designed based on the three circuits:1) LIMS (Low Intensity Grinding Rolls) feed grinding-LIMS test-flotation test2) LIMS feed grinding-flotation test-LIMS test3) LIMS concentrate grinding-flotation testThe best results were obtained using the first circuit at the LIMS feed size (d80) of 132 ?m. The processing results using the circuit no. 1 (feed type: A), showed a LIMS concentrate with 69.8% of Fe and 0.36% of sulfur. In this case, the final concentrate (after flotation) with Fe grade of 70.3%, sulfur content of 0.07% and Blain no. of 1571 cm2/g were obtained. In case of the feed type of B, the LIMS concentrate with Fe grade of 68.7%, and sulfur grade of 1.6% was achieved. Also, the Fe and sulfur contents were 69.3%, and 0.4% respectively with a Blain number of 1112 cm2/g. According to the obtained results, it was suggested that a LIMS feed comminution along with a LIMS and flotation systems are necessary to achieve an appropriate iron and sulfur grades with an acceptable blain number. To reach a concentrate Blain number as a pelletizing feed, a High Pressure Grinding Rolls (HPGR) system at the end of the processing line was recommended."

Jan 1, 2016

By D. J. Lloyd

"Bending is involved in the forming of many sheet parts and it is important to understand the phenomena involved. In this paper the basic equations describing bending on a global scale are compared with strain measurements of bent sheet. The development of strain on a local, microstructural scale is also investigated, as is the general aspects of plasticity and the failure process. It is shown that the global equations can be used to estimate the strains involved and the local strains can be attributed to various aspects of the plasticity. The bendability can be related to the fracture strain of the sheet and the ability of a sheet alloy to accommodate the necessary bending to form the part can be assessed.INTRODUCTION The ability of a sheet alloy to undergo bending without failure is an important capability in the forming of many parts and it is useful to be able to assess the bendability of an alloy during its development. The basic mechanics of bending were developed in the 1950s (Lubhan & Sachs, 1950; Hoffman & Sachs, 1953). When a sheet is bent the upper bend surface is in tension, the lower surface in compression and at some point within the sheet there is a plane of zero strain which is referred to as the neutral axis. For sheet exhibiting limited plasticity the neutral axis is static and occurs at the mid-point of the sheet thickness but for sheet exhibiting extensive plasticity the neutral axis progresses deeper in to the sheet as bending progresses. This results in two expressions for the maximum strain at the upper bend surface depending on the motion of the neutral axis. For Al alloys such as AA6111, AA6016 and the like extensive plasticity occurs and the neutral axis is expected to move during bending. However, very few studies have examined how the neutral axis motion and the strains develop, compared with the mechanics analysis. Geist and Parker (1984) used hardness measurements to investigate neutral axis motion but these experiments did not have the resolution necessary to compare the results with experiment but did indicate neutral axis motion. To understand the nature of plasticity and failure during bending it is important to know the extent of neutral axis motion, the scale of strain gradients developed through the sheet and the maximum strains occurring at the bend surface, finally comparing experimental results with the theoretical predictions. The influence of microstructure on the evolution of strain and failure can then be considered in the context of these parameters. Recently, bending in some automotive Al alloys has been reported mainly from the microstructural perspective (Lloyd, 2000, Lloyd et al., 2002, Mattei et al., 2013) and FEM studies have also investigated the development of plasticity under bending, demonstrating the tendency for strain localization (Becker, 1992, Shi et al., 2014)."

Jan 1, 2018

By W J. Riva

This paper reviews the coal mining operations of The Canmore Mines, Limited, at Canmore, Alberta, paying particular attention to the use of this coal by the metallurgical and chemical industries. The characteristics of the deposits are outlined, and the mining and processing methods used are discussed. Introduction M INING in the Cascade coal area of Alberta began form-ally in 1886 when the Canadian Anthracite Coal Company was granted its charter. Earlier operations had been confined to prospecting and family-type enterprises serving the market area within barging distance on the Bow river. From 1886 to 1964, seven mines were opened between Banff and Ribbon Creek; six of these have since been abandoned, leaving the B c 0 L. original tenant, under the name of The Canmore Mines, Limited, as the sole survivor. The town of Canmore, hub of the mining ventures, is located on the main line of the C.P.R. and on the Trans-Canada Highway, 67 rail miles west of Calgary and 57 4 miles east of Vancouver, as shown in Figure 1.

Jan 1, 1965

By W. B. Xie

The hardening behaviour and microstructure evolution of Cu-30Ni-30Mn alloys aged at 350 °C has been investigated utilizing optical microscope, scanning electron microscope, transmission electron microscopy and Vickers hardness tester. The results show that the discontinuous precipitation of NiMn phase results in a remarkably hardening effect in Cu-30Ni-30Mn alloy during aging at 350 °C. The maximum hardness (~494HV) is attained in the sample after aged for 48 h. The NiMn precipitates are ordered and have a face-centered tetragonal structure. The coherent orientation relationship between the NiMn precipitates and Cu matrix is (220)Matrix // (220)P, [1-1-2]Matrix // [1-1-2]P. In addition, there is a linear relationship between hardness and volume fraction of the discontinuous precipitation, which indicates that the hardness increment of Cu-Ni-Mn alloys aged at 350 °C is attributed to the microstructure characteristics of discontinuous precipitation. The high strength of discontinuous precipitation colony is caused by the formation of nanoscale NiMn precipitates with a lamellar structure in discontinuous precipitation. INTRODUCTION Cu-Ni-Mn alloys are attractive candidates for oil drilling, aerospace and energy applications due to their high elasticity, high strength and excellent corrosion resistance (Sun et al., 2009; Liu, Yang, Xia, Jiang, & Gui, 2016). The high strength of the Cu-Ni-Mn alloys is mainly attributed to the precipitation of NiMn phase (Shapiro, Tyler, & Lanam, 1974; Xie et al., 2015). The uniformly dispersed nanoprecipitates formed by continuous precipitation can impede dislocation movement, and thereby lead to a significant improvement in strength of traditional precipitation-strengthened alloys. However, it is reported that there are two precipitation types observed in Cu-Ni-Mn alloys, namely, continuous precipitation and discontinuous precipitation (Shapiro et al., 1974). The discontinuous cellular colony with a lamellar structure nucleates at grain boundaries, and progressively grows inward the grain on the process of discontinuous precipitation (Ng, Bettles, & Muddle, 2011). It is found that the discontinuous precipitation can occur in many Cu-based alloys, such as Cu-Ni- Mn alloy (Shapiro et al., 1974), Cu-Be alloy (Monzen, Hasegawa, & Watanabe, 2010) and Cu-Ni-Sn alloy (Zhao, & Notis, 1998). Many studies consider that the discontinuous precipitation results in a detrimental effect on hardness and strength, and the discontinuous precipitation occurring during aging treatment should be suppressed (Markandeya, Nagarjuna, & Sarma, 2004; Semboshi, Sato, Iwase, & Takasugi, 2016). The mechanical properties can also be improved by discontinuous precipitation in AZ91 magnesium alloy (Tamura, Kida, Suzuki, & Soda, 2009) and AM30 magnesium alloy (Saikawa et al., 2012). Jun (2017) found that the reduced interlamellar spacing of precipitate fibers in discontinuous cellular colony leads to a significant increase in hardness. Indeed, the strengthening contribution of discontinuous precipitation is similar to that of continuous precipitation in Cu-20Ni-20Mn alloy. Discontinuous precipitation of NiMn phase can provide a significant strengthening effect in Cu-Ni-Mn alloys.

Jan 1, 2019

By Lionel A. York

This paper outlines the type of water-bearing formations encountered in the Prairie Sediments and describes a method for effectively sealing these zones in order that shaft-sinking operations may be carried out with safety. Details are given of the procedure for carrying probe holes ahead of the shaft bottom. These probe or grout holes are employed for establishing a series of overlapping grout covers around the proposed shaft excavation to safeguard against large inflows of water during sinking. The pattern and length of grout covers cannot be standardized, and each cover needs to be specially designed to suit the varying ground conditions. In order to provide effective protection through the Prairie Sediments, the number of holes in any one cover would not be less than 8, and possibly as many as 64 would be required in certain zones. The length of covers would vary from 100 ft. to 250 ft. Emphasis is placed on the need for obtaining accurate geological and water information from exploratory holes, drilled in the shaft vicinity, in order to effectively plan all grout covers.

Jan 1, 1964

By Haofeng Xie, Lijun Peng, Xujun Mi, Xue Feng, Xiangqian Yin, Zhen Yang, Guojie Huang

The Cu/Al composite wires have been widely used in cable industry. Especially in the development of aerospace, the light weight character of wires is particularly important. The wires are fabricated by a drawing process and heat treatment. Mechanical and electrical properties are measured and analyzed. The bending behavior is studied by scanning electron microscope. INTRODUCTION Cu/Al composite is a typical bimetallic composite that has been used in plenty of fields such as automobile and aerospace. The composite has the advantages of excellent conductivity as well as low weight, which cannot be obtained from single copper or aluminum. Industrial products of Cu/Al composite include Cu/Al composite joints (Uscinowicz, R., 2013), Cu/Al bimetallic sheets (Li, X. et al., 2011), Cu/Al flat bar (Wu, Y. & Liu, X. & Xie, J., 2014) and CCA wires (Ahmed N., 1978). CCA wires refer to the composite wires that copper layer concentrically coated on the surface of aluminum core conductor, implementing solid combination of two metals on the interface and forming an integral. At present, the aircraft cable generally use copper or copper alloy conductor, which makes the wire in the aircraft occupy a considerable proportion due to the large density of copper. Therefore, the use of Cu/Al composite wires instead of copper wires for weight loss, is of great significance to the development of aerospace technology industry. Heat treatment is an indispensable procedure to improve plasticity during cold working process, which is of great importance to preparation of wires (Wang, Q. et al., 2008). During the heat treatment, the Intermetallic Compounds (IMCs) are inevitable formed at the contact area of Cu/Al due to the occurrence of diffusion (Lee, S. et al., 2012). According to the results of former researchers, kinds of IMCs were discovered. Antoine Gueydan (2014) identified the formation of three IMCs (Al2Cu, AlCu, and Al4Cu9) at the interface between copper and aluminum after thermal aging. IMCs have a significant effect to the properties of Cu/Al wires. Bending performance is a vital property for the actual application of wires. The brittle IMCs may create a stress concentration that can cause crack initiation during bending process. This work focus on the mechanical properties of Cu/Al composite wires after heat treatment. The effect of various annealing condition on mechanical and electrical properties are studied, in order to find the appropriate annealing conditions, which produce optimal combination properties of Cu/Al clad composite wires. Bending fracture of composite wires is discussed by morphology observation.

Jan 1, 2019

By Ernest Becker

Golder Associates provided overall radiological direction and assistance to the client in their interactions with the Canadian Nuclear Safety Commission and operational radiation protection services for the remediation of a calciner that had been used to process uranium. The project was somewhat unusual in that the radioactivity from within the calciner room was removed from the site and the cleaned steel recycled. The presence of yellowcake within the process equipment required stringent radiation protection measures. This project was completed successfully with minimal radiation exposures to the workers and the effective protection of the environment.

Aug 1, 2010

By Shigeomi Nishigaki

This paper presents quantitative indexes to evaluate operator?s bearing, difficulty in a task, and machine operability when an operator remotely controls a backhoe, and reports the use cases. The quantitative indexes would give her/him the opportunity to reflect on her/his works, and enable us to gain in-depth insight into the teleoperation, and furthermore give us with promising hints to improve it.

Aug 1, 2013

By P. M. Chapman

Risks to aquatic receiving environments from uranium mining and milling fall into three categories: physical (habitat change), chemical (e.g., uranium, selenium, total dissolved solids [TDS], metals including vanadium), and radiological. Although all categories of risk need to be managed, chemical risks are the most significant and are typically chronic rather than acute. For instance, selenium toxicity is primarily manifested as reproductive impairment due to maternal transfer, resulting in embryotoxicity and teratogenicity in egg-laying vertebrates. Risk is best assessed using a weight of evidence approach focused on ecosystem services. Risk management should be based on both risk assessment and adaptive monitoring.

Aug 1, 2010

By T. Loos

The Norddeutsche Affinerie operates an Outokumpu-Flash-Furnace as a smelting unit. The pyrometallurgical slag cleaning process is based on the slag reduction and settling in the electric furnace. Since 1972 when the slag cleaning furnace was built the throughput could be increased fourfold. However, an extensive optimisation effort is required in order to keep the copper loss low. A parameter study with a neuronal network model based on real process data was conducted to identify parameters impacting on the copper loss in the slag. It could be demonstrated that the main parameters responsible for copper loss in the final slag are fixed parameters of the flash furnace. For a better understanding of the copper loss in the electric furnace microscopic analyses of the slag structure and viscosity measurements were performed. Based on these results the reduction and settling of the copper containing droplets could be increased in both pilot plant studies and industrial scale. 4

Jan 1, 2007

By Lyle F. Smith

With the demand for larger diameter raises under all ground conditions and the increasing price of drill rods and operating costs, it was evident that there was a need for a raise borer with a variable-speed drive and fast-response torque limiting control. The raise boring machine described in this paper was developed after several years of market research and discussions with mine operators and construction contractors. This paper discusses the Ingersoll-Rand raise borers with the solid-state controlled DC motor drives. These machines have gained wide acceptance in the five-year period since being placed in operation and are designed to accommodate the range of raise diameters and lengths most required today.

Jan 1, 1978

By R. O. Loutfy, J. C. Withers

"Titanium powder is produced from a small fraction of sieved sponge, HDH of sponge or gas blown from a melt produced billet. Ore from foreign sources is chlorinated in a very high temperature fluid bed to make TiCl4, then vacuum distilled purified and then reduced to sponge by Kroll processing. Domestic ores of ilmenite or perovskite can be carbothermically reduced to Ti2OC which can be chlorinated at low temperatures of 250–400°C to produce TiCl4 which can be electrolyzed in a fused salt to Ti powder, or the Ti2OC used as an anode in electrolysis to produce Ti powder. The electrolysis process can be operated continuously to produce Ti powder at a lower cost than Kroll processed sponge including produce control size powder. Electrolysis processing was scaled up and operated at the commercial demonstration stage on a continued basis that verifies the potential of a low cost process to produce Ti powder.INTRODUCTIONTitanium and alloys of titanium powder have been elevated to strategic status resulting from a focus of producing meltless titanium components as well as a feed for additive manufacturing processing. However, the high cost of titanium powder has limited wide scale implementation of using titanium powder as a feed to any process to produce titanium components. Titanium powder free of alloying is available as sponge fines from the Kroll process as illustrated in Figure 1. Titanium alloy powder is much more expensive, also illustrated in Figure 1 produced from an alloy ingot or mil product as the feed and then transformed into powder by one of several melt form processes which accounts for the high cost of titanium alloy powder at approximately $60–150/lb. Ton lots of titanium alloy powder (i.e. Ti-6Al-4V) from one source is quoted at $120/lb. in the U.S. It appears that alloy powder production cost by current processing is not sensitive to volume."

Jan 1, 2016

By T. H. Wilson

In 1901, the Crow's Nest Pass Coal Company, Limited, began producing industrial coke in 212 beehive ovens at Michel colliery. By 1908, 486 ovens had been installed and in that year 147,623 tons of coke were produced. Coke manufacture has been continuous from 1901 until the present time (1946), with total production of 2,795,402 tons. At present writing, only 100 beehive ovens are operating and production is reduced to 1,800 tons per month, due to the shortage of suitable labour. These ovens are drawn by hand, on contract, and the workmen are exposed to considerable heat. A man draws three ovens in eight hours, thereby producing approximately 1072 tons of coke per day. In addition to the inefficient and costly method of drawing coke in beehive ovens, tremendous losses are experienced in the wastage of gas and tar, which are driven off into the atmosphere. Also, the yield of coke per ton of coal fed to the ovens is low as part 9f the carbon is utilized in producing heat to carbonize the remainder of the coal. A recovery of only 55 per cent of the carbon, as coke, is obtained. The coking process takes place from the top of the charge, which is 21/2 feet deep, downward to the floor. Six and a half tons of coal are charged and 3.6 tons of coke are drawn from the oven after 72 hours' carbonization. The beehive ovens using Michel coal produce a very hard and tough coke, large in size and of silvery appearance, which has served the requirements of both foundry and smelter for many years. In 1938, the Company made a careful study of coking processes with a view to introducing a more economical method than beehive ovens and one that would be less dependent on skilled labour, the supply of which was rapidly diminishing at that time. Various methods of by-product coking were investigated, and it was decided that the Curran-Knowles process offered the greatest possibilities because of the low capital investment in relation to output and also because the horizontal oven design was suitable for an expanding coal. Consequently, a test on Michel B seam coal, supervised by Mr. E. Burrough, of the Fuel Research Department, Ottawa, was run in the Curran-Knowles plant at West Frankfurt, III. The results of this test led to the construction of a ten-oven battery of 32 ft. 6 in. by 8 ft. 3 in. Curran-Knowles ovens at Michel, which were completed in November, 1939. This battery was built as an experimental unit, with provision for an additional ten ovens if the coke proved satisfactory for the market. In 1942, an expanding coke market led to the construction of a second battery of ten ovens, which were completed in April, 1943.

Jan 1, 1947

By E. P. Evoy, A. W. Jolliffe

"The Uranium deposit of Gunnar Mines, Limited, is on the south shore of Crackingstone peninsula in the Beaverlodge area of northern Saskatchewan.The ore consists of disseminated pitchblende and uranophane in brecciated syenite, and forms a tubular or pipelike body, outcropping at the surface and plunging southward at about 45 degrees for a known length of1,400 feet (see Figure I). The upper portion is being removed by open-pit mining to a depth of 300 feet below adjacent Lake Athabasca. The remainder will require underground mining methods (see Figure 2).The property was staked in July, I 952, and the orebody was subsequently defined by about 70,000 feet of diamond drilling. A 1,250-ton mill was completed in 1955, and production commenced in September of that year with ore from the open-pit operation. The mill is presently being increased to 1,650 tons capacity, and a three-compartment vertical shaft is being sunk to 1,250 feet in preparation for underground mining.GeologyThe mine property is underlain by an assemblage of Precambrian metasediments known locally as paragneiss, granite-gneiss, and syenite. These lie on the southeast limb of a southwest-plunging anticline, strike about north 75 degrees east, and dip southward at about 45 degrees. Para- gneiss outcrops in the northwestern half of the claim group, and again on the islands south of St. Mary's Channel. The granite-gneiss lies conform-ably within the paragneiss and makes up the southeastern part of the property. The syenite forms an irregular, triangular-shaped mass within, and near the footwall of, the granite-gneiss band. Small lenticular bodies of mafic rocks are also present, the former being most prevalent in the paragneiss.The granite-gneiss is coarse to medium-grained, pink to grey, well foliated, and composed of feldspar (65 per cent), quartz (20 per cent), chlorite, and minor mica. The general concordance of its contacts with paragneiss and the absence of intrusive relationships along these, the presence of uniformly oriented inclusions of obviously sedimentary origin within the granite-gneiss, and the variation in colour and texture across the strike all strongly suggest that this member represents a granitized sedimentary rock."

Jan 1, 1949

By F. N. Smith

Corrosion was observed on the aluminum pressure plates and dress-caps that hold the glazing in place on a curtain-walled building, The multi-storey building in question is situated in the downtown area of a busy Canadian city, For aesthetic reasons, the original design required the dress-caps (which have L-shaped cross-sections) to be externally clad with thin copper sheet. Since the aluminum was in direct contact with the copper trim, galvanic corrosion developed that resulted in damage to the aluminum components, Soluble corrosion products washing off the copper trim may also have contributed to the accelerated corrosion of the aluminum, The aluminum pressure plates and dress-caps are being systematically replaced with components made of fibre-reinforced plastic. The outsides of these new components will be clad with thin copper sheet in order to preserve the original appearance of the building.

Jan 1, 2005

By D. R. BUDINSKI

Clinton Creek Mine in west-central Yukon produced 0.94 million tonnes of fibre from 15 million tonnes of asbestos ore between 1968 and 1978. The mine closed in 1978. The deposit lies along the margin of a medium sized ultramafic pluton that intrudes schistose and gneissic rocks of the Yukon Metamorphic Complex. Country rocks are metamorphic equivalents of a mixed sedimentary and volcanic assemblage deposited during Precambrian or early Paleozaic time. Movement along the north west-trending Tintina Fault System probably caused the fairly high meromorphic grade that altered the original rocks to schists and gneisses. The ultramafic pluton hosting Clinton Creek Mine is one of several bodies that were emplaced along a deep seated imbricate fault system parallel to the Tintina Trench. Most of rhe intrusions were hydrothermally altered to serpentinite, bur apparently only the one at Clinton Creek contains commercial quantities of asbestos. The Clinton Creek pluton was probably injecred slowly at relatively low temperatures into the crustal rocks as a "mush" that cooled gradually, allowing sufficient time for serpentinization and chrysotile fibre crystallizarion.

Jan 1, 1984