Search Documents

By R. Pakalnis, D. Tenney, B. Lang

"This paper describes three case histories whereby numerical methods were employed as a tool in the identification of potential instability. Simple two dimensional (PCBEM) and pseudo three-dimensional (BESOL, MINTAB) codes were employed to identify zones of induced stress which were subsequently related to extensometer, stress meter and observational data as the stope was excavated. The following case histories will be discussed. MacLellan Mine - sill pillar stability; Ruttan Mine-Hanging Wall Stability; and Detour Lake Mine-narrow vein mining.The MacLellan case history showed how modelling and instrumentation enabled mining to be conducted safely and under controlled conditions. MINTAB and PCBEM were employed to predict sill pillar failure. The sill pillar failure was associated, with an unloading of stress which was recorded by instrumentation (stress meter) and a decrease in the over-all rock mass strength. The yielded pillar, however, maintained its over-all configuration enabling access through the pillar.The Ruttan case history is an example of hangingwall and footwall design whereby the existence of adverse structure coupled with a zone of relaxation results in dilution. BESOL and PCBEM were employed to model a test stope and to verify the observations and measurements through instrumentation . Empirical methods of dilution estimates are employed to determine the level of walls lough with respect to the rock mass rating, stope dimensions and rate of excavation.The Detour Lake case history in an example of open stoping a narrow steeply dipping deposit. Stope dimensions are 135m in strike length, 47 m in vertical height with an average width (F/W to H/W) of3.6 m. Stress meters coupled with visual observations are related to modelled estimates of stress and dilution."

Jan 1, 1991

By E. Essadiqi, P. Poruks, D. Boyd, D. Emadi, I. Yakubtsov, T. Turi

This paper reviews the results of an extensive study of microstructures and mechanical properties in bainitic linepipe steels. The research was carried out as a collaborative project between Queen's, Stelco and CANMET. Basic studies of phase transformations and mechanical properties in these steels established important relationships between processing schedule and microstructure evolution, and between final microstructure and mechanical properties. The best combination of strength and toughness properties is obtained with a microstructure comprising a matrix of intragranularly-nucleated bainite (`acicular ferrite - AF') and small (~ 0.5 µm) dispersed particles of martensite (`M/A'). We describe this as a dual-phase AF+M/A microstructure. An experimental study on 15-mm thick plate determined the window of steel composition and processing parameters which gives the dual phase AF+M/A microstructure. The minimum strength and toughness properties for Grade 621 (X90) linepipe steel can be achieved by either a lean steel composition (0.04C-1.77Mn-0.04Cr¬0.32Mo-0.31Ni-0.29Cu-0.08Nb) with extreme processing parameters, or by a higher alloy composition (0.04C-2.07Mn-0.50Cr-0.51Mo-0.04Nb) with a more industrially realistic processing schedule. It is proposed how this approach could be extended to obtain higher strength linepipe grades.

Jan 1, 2005

By M. A. Upham

"Prairie Evaporites of the Province of Saskatchewan in a deep oil-well hole. Exploitation started in 1950 under a shroud of doubt that this huge reserve could be mined. It was fraught with almost insurmountable physical problems in penetrating the Prairie Evaporites. After 12 years of experimentation and development of new shaft-sinking methods, mining equipment and processes to treat the high-grade potash ore (sylvanite), a new era of high-risk resource development dawned in Saskatchewan.The development of 10 new mines opened up the largest known mineable potash reserves in the world and Canada became the second largest. producer of potash to supply domestic (U.S.A. and Canada) and overseas markets. A monumental program in marketing-devising new transportation systems and strategically locating warehouses-was developed in order to expeditiously service domestic and overseas customers. The year 1969/70 started a period of overcapacity and the problem of prorationing. As the market strengthened in 1974, the Saskatchewan Government applied the reserve tax to the industry. Then, they announced the setting up of a Crown corporation to acquire ownership by purchase of up to fifty per cent of the industry. During this time, potash was discovered in New Brunswick within 50 to 60 miles of a seaport, where two deposits have been explored by the same pioneers who started the potash development in Saskatchewan.With this background, the paper will examine various elements of the economics and marketing of Canadian potash."

Jan 1, 1980

By Michel Dagbert

"In their paper, Marcotte and Boucher (2001) cast some new light on the old problem of 2D estimation of vein-type deposits with thickness and grade of intercepts. Using a theoretical approach, some extensive simulation experiments and the Walker Lake data, they show that the direct approach (interpolation of grade at points on a regular grid) gives better estimates of the true grade at those points than the indirect approach (interpolation of grade x thickness or accumulation and interpolation of thickness) when there is some positive correlation between grade and thickness and that this better performance increases with the correlation of grade and thickness as well as the variability of both variables.We would like to bring some reservations to that conclusion by showing that even if direct point grade estimates are better than indirect ones, it is not necessarily true for block estimates and in particular for the estimated grade of the whole orebody itself."

Jan 1, 2001

By R. S. Rogers

Abstract - Forensic geology in a mineral exploration context is concerned with geology and related technical matters as they pertain to legal cases involving exploration and evaluation of mineral properties. Such cases involve the possibility of outright scams that include falsification of data and information, as well as inappropriate application of various technical procedures. Experience in forensic geology in such cases emphasizes the need for systematic quality control procedures during routine exploration/appraisal and indicates the need for more attention to ‘target hardening’ (improving security in the chain of custody of samples and assay results). A number of ‘early warning signs’ that might suggest some form of tampering or falsification of information are listed. These measures will support the work of the "Qualified Persons" (geologists and engineers) entrusted with the scientific and technical aspects of mineral exploration, and facilitate the increased attention to regulatory oversight and enforcement of securities laws recommended in the report "Setting New Standards."

Jan 1, 1998

By Michel Dagbert

"In their paper, Marcotte and Boucher (2001) cast some new light on the old problem of 2D estimation of vein-type deposits with thickness and grade of intercepts. Using a theoretical approach, some extensive simulation experiments and the Walker Lake data, they show that the direct approach (interpolation of grade at points on a regular grid) gives better estimates of the true grade at those points than the indirect approach (interpolation of grade x thickness or accumulation and interpolation of thickness) when there is some positive correlation between grade and thickness and that this better performance increases with the correlation of grade and thickness as well as the variability of both variables.We would like to bring some reservations to that conclusion by showing that even if direct point grade estimates are better than indirect ones, it is not necessarily true for block estimates and in particular for the estimated grade of the whole orebody itself."

Jan 1, 2001

By Timothy W. Ellis

Gold-based materials have been a mainstay of the electronics and semiconductor industry since the physics was just a laboratory curiosity. Gold is the workhorse material in wire bond, flip chip and off wafer interconnections due to its corrosion resistance, ability to form metallurgical bonds by soldering or cold welding, and ease of fabrication. As the electronics and semiconductor industries grew, so did the use, of Gold in spite of the feature size reduction so elegantly demonstrated in Moore?s law. However, several revolutions in the Silicon miracle are threatening Gold?s place as the material of choice. Although cost is always an issue, the limitations are associated with the chemistry of Gold based alloys. Will Gold remain? Emerging requirements of bioelectronics, photonics and power requirements in conventional device represent new opportunities for Gold to shine. Additionally, as the world market demand for electronic, semiconducting, bio-electronic and photonic technology increases, given the right technology, Gold still can provide value proposition.

Oct 1, 2003

By Robert B. Parsons

"First down and four to go. In the game Of football, this is not a bad position to be in. However, in this game of political football, it means that there is still a long way to go. The government in Ottawa has concluded an important agreement with one producing province, and now has at least four more provinces to deal with-B. c., Saskatchewan, Nova Scotia and Newfoundland.On September 1, 1981, the federal and Alberta governments took a significant step forward in formulating an oil and gas policy for Alberta and the rest of Canada on signing a comprehensive five-year agreement that covers taxes, prices, incentives and other fiscal matters related to the production and marketing of oil and gas.This month, Tax Notes examines the main features of the agreement, and offers some eye-opening observations of what the new accord could mean for the future of the Canadian petroleum sector in particular and Canadian business in general."

Jan 1, 1981

By G. W. Poling, E. M. Coelho

"Sedimentary phosphate ores make up approximately 87% of the world's known reserves and are generally more difficult to beneficiate than igneous ores. In almost all cases, desliming prior to flotation represents the major source of losses. Laboratory studies of selective desliming of sedimentary ores are presented. Some fundamental studies with pure mineral systems are also discussed. Selective desliming, especially using selective flocculation, gave the best performance. Possible industrial applications of this selective flocculation-flotation procedure are discussed.IntroductionPhosphate ores are a major source of raw materials used in inorganic fertilizers (which supply nitrogen, phosphorus and potassium). Approximately 96% of the total world production of phosphate is utilized in the fertilizer industry. Reserves and production data are available in the literature. Today deposits with grades as low as 4% P2O5 are exploited in a few cases. However, in some northern African deposits, ore grades are still as high as 33 - 35% P2O5. Hout pointed out in 1982 that approximately 200 million tonnes of phosphate ore were upgraded by flotation only.Although there is a large number of phosphate minerals (over 300, only those in the apatite series are important ore minerals in phosphate ores. The most common member in this series is fluorapatite – Ca5(PO4)3F. However, in sedimentary phosphate rocks, many different substituents occur in the apatite lattice. Carbonate-fluorapatite (or francolite) is one of the most common names used to describe sedimentary apatites. It can be represented by the empirical formula:"

Jan 1, 1986

By Ted J. Smith, Stephen E. Kesler

"Zonation patterns are welt developed in the mafic metavolcanic rocks that host epigenetic quartz-carbonate-gold vein mineralization at the Hollinger-McIntyre deposit. Carbonate alteration assemblages are strongly zoned about mineralization. Proceeding inward from background greenschist facies rocks to alteration envelopes enclosing individual veins, the following assemblages are observed:Assemblage I-quartz-albite-chlorite-epidote-actinolite-(calcite)Assemblage II-quartz-albite-chlorite-calcite-epidoteAssemblage III-quartz-ankerite-sericite-(chlorite-calcite)Assemblage IV-quartz-albite-ankerite-sericiteLithogeochemical zoning is equally well developed as variations in whole-rock abundances ofAs, Au, Ba, Rb, and Sb. As and Ba form the most useful zonation patterns, outlining individual ore zones as well as broader trends of mineralization.Gas chromatographic analyses of fluid inclusions in the quartz-carbonate veins indicate that the mineralizing fluid was an H20-C02 mixture. Locally, CH4-rich fluid inclusions are associated with graphitic and/or carbonaceous wallrocks. Fluid inclusions in ore-bearing veins have higher CO2 contents than those in non-ore veins. Extensive sampling and analyses of veins from the area surrounding the deposit reveals a well developed zonation of CO2 contents about the main zone of mineralization. Low CO2 levels (1-2 mole%) in veins are peripheral to the deposit and increase to over 12 mole% in mineralized zones.The observed zoning of the carbonate alteration assemblages is a result of the addition of CO2 to the wallrock, which is consistent with the zoning of CO2 in the fluid inclusions.The zoning patterns delineated in this study are useful in exploration both on a deposit scale and on the scale of individual ore zones."

Jan 1, 1985

By P. S. Daly

"The purpose of this paper is to describe the types of instrumentation used at Sherritt Gordon's Ruttan Mine to monitor the"" effects of mining. The aim of the monitoring program is to establish parameters to achieve a maximum ore recovery with minimum dilut ion in a safe environment.The copper-zinc Ruttan Mine is in northwestern Manitoba, approximately 760 km from Winnipeg (Fig . I) . Production commenced in 1973 from the open pit at the rate of 10,000 tons per day. Pit bottom lies 58 metres above the first mine level. Underground development has overlapped with open-pit mining throughout. The open pit was phased out in the latter part of 1980.Underground production began in early 1979. The mining method employed in the first lift is sub-level blasthole open stoping with delayed hydraulic filling. Large-diameter (6.5-in.) holes are being drilled in the crop stope area and are also planned for some other areas for vertical retreat mining into a slot. GeologyThe orebody consists of numerous sulphide lenses of variable size, geometry and geology . The lenses occur within volcanoclastic host rocks which exhibit a strong variability in intensity and type of alteration and structural characteristics. Stope design and sequencing were based on these complex geological factors."

Jan 1, 1981

By Patrice Nadeau, Yuejun Zhang, Dan Chen, Liming Huang, Claude Gagnon

"The traditional Denver flotation cell is generally suitable to process material ranging approximately from 5 µm to 300 µm. For floating over 300 µm material, its efficiency is significantly getting lower mainly due to the difficulty to suspend coarse particles uniformly, which decreases the chances of particles to attach to bubbles and increases the chances of detachment.RTFT (Rio Tinto Fer et Titane) owns one of the world’s largest hemo-ilmenite deposits. Considering the whole processing technology, the ore is only crushed to -1180 µm. The crushed ore contains about 0.32% S and most of the sulfur is removed by rotary kilns in the ore preparation plant. In order to achieve a similar S reduction, without emitting SO2 into the air, an alternative technology by flotation was pursued.Laboratory and pilot scale-up tests showed that traditional Denver flotation cell could perfectly remove the sulfur from the material sizing 0-300 µm. For the coarser particle sizes, two different models of equipment were tested to improve flotation efficiency: HF (HydroFloat Separator) from Eriez and CLF from BGRIMM (Beijing General Research Institute of Mining and Metallurgy), China. The D6” HF, which is a device that combines flotation and gravity separation, demonstrated its ability to recover those very coarse particles. As compared to the Denver flotation cell, the modified 25 L CLF coarse particle flotation cell achieved better results at higher pulp solids percentage and with a shorter flowsheet."

Jan 1, 2016

By Gabriel Zarate

"Los Bronces had two ROM dump leach operations designated Leach I and Leach II. Leach I was commissioned in 1998 and stopped in 2014 due to the mine requirements. Leach II plant, commissioned in early 2002, was built to treat around 700 million tons of marginal ROM ore averaging 0.45 % total copper. The mineralogy of this material was estimated to be 70% chalcopyrite, 20% chalcocite/covellite and the balance oxides.The original electrowinning plant design capacity for copper production was nominal 19,500 tonnes per year at a current density of 276 A/m2 and a current efficiency of 92%. Presently, Los Bronces San Francisco plant typically operates at current densities between 390 and 440 A/m2, much higher than the average in the industry, with current efficiencies around 93% and a maximum copper cathodes production of 37,200 tonnes per year.In order to accomplish these achievements, a number of modifications in the process conditions, in the cell hardware and in the operational procedures have been implemented. In the first case, the specific flowrate, copper concentration and temperature of the electrolyte were modified to accommodate the operational requirements facilitating the increased current density. Associated with the cell hardware, a six cells expansion was added, upgraded equipotential inner cell busbars were installed and the cross section of the cathode hanger bars was enlarged for increased current carrying capacity. Documented operational procedures like short circuit detection and cathode weight control were improved.The modifications implemented and the results obtained are discussed in this paper.INTRODUCTIONLos Bronces Division of Anglo American Chile is located up in the Andes Mountains, northeast of Santiago. It had two cathode plants, Los Bronces at an altitude of 3500 meters above sea level (m.a.s.l.) commissioned in 1998 and closed in 2014 and San Francisco at an altitude of 2800 m.a.s.l. and in operation since 2002.The process is leaching run off mine (ROM) low grade copper sulphide ore in dumps. The mineralogy of this material was estimated to be 70% chalcopyrite, 20% chalcocite/covellite and the balance oxides. The average grade is 0.45% total copper (Cut).At Los Bronces dump, Leach I plant, the pregnant leach solution (PLS) was collected and stored in an underground reservoir. From there, it was fed to a solvent extraction plant with a series-parallel configuration in two extraction stages and one stripping stage. The electrolyte produced was fed to the electrowinning plant having 30 cells and 60 cathodes per cell. Maximum capacity of this plant was 12,000 tonnes per year (tpy)."

Jan 1, 2016

By D. A. Mackie, J. E. Rider

"Good belt conveyor design is the most often neglected detail in the engineering of a plant. This results in downtime from spills or jams and premature failure of equipment components. Careful layout and component selection will result in better operation, a cleaner plant and therefore lower maintenance costs.IntroductionDespite the availability of many excellent sources of data on conveyor design, such as the Conveyor Equipment Manufacturers' Association (CEMA) Manual, ""Belt Convyors for Bulk Materials"" , there continues to be repetitive errors made in design. Why? Certainly, there is no substitute for experience, but largely, classical errors in belt conveyor design is rather elementary and so the temptation to have the work done by relatively inexperienced designers is great. What that does is develop "" experienced"" designers who become incompetent through no fault of their own. It is hoped that this paper will supplement available design data, help those who are "" put into"" a design situation to better cope with their predicament, and ease the lives of plant maintenance personnel."

Jan 1, 1990

By Holly L. O. Huyck

Disseminated hypogene sulphide mineralization in the Lakeshore porphyry copper deposit (also called the Cyprus-Casa Grande deposit) of Arizona occurs in both a granodiorite stock and associated volcanic rocks. Structural development and vein paragenesis at Lakeshore are similar to other Laramide porphyry copper deposits of the southwestern U.S. Two major structural trends are present: intrusive contacts, copper-bearing potassic alteration veins and major post-mineralization Basin-and-Range type faults trend N-NW, whereas phyllic veins and secondary post-mineralization faults trend N-NE, and deep propylitic veins trend NE-ENE. Lithologic permeabilities, caused by fracturing in all rocks and by grain size distributions in volcanic rocks, controlled the distribution of copper mineralization. Differences in chemical compositions of host rocks did not affect are grade. Structural control, through density of chalcopyrite-rich veins, was the major control of are grade. Fracture density of other potassic vein types did not strongly affect grade. Within volcanic lithologies, permeability, as indicated by grain size distribution, provided a second-order, but significant, control of mineralization.

Jan 1, 1990

By T. M. Ahmed

Sherritt International Corporation experienced corrosion failures with the 316L stainless steel tubing in a high-pressure still condenser employed for ammonia recovery. A detailed failure analysis was conducted on the condenser tubing to determine the mode and the root cause of the failure. The analysis included both optical and scanning electron microscopy (SEM) of the inner and outer surfaces of the tube as well as characterization of the corrosion products using energy-dispersive X-ray spectroscopy (EDX). Results revealed that the corrosion attack was confined to the first ?100 mm of the tubing at the inlet where the tube was connected to the top tubesheet. The tube suffered both external stress-corrosion cracking (SCC) and crevice corrosion from the shell side (water side), and wall thinning of the inner surface (the tube side) due to erosion corrosion. It was evident that failure of one of the tubes occurred due to SCC that penetrated the whole wall thickness and resulted in a leak failure. Some prevention measures are proposed to avoid this type of corrosion attack in the future.

Jan 1, 2005

By W. W. Muir

"The Baker Mine used a 100-ton per day conventional cyanide leach mill located in northern British Columbia. A production decision was made in early 1980 and the mill was on fine in April 1981.Ore reserves had been estimated at 100,000 Ions averaging 0.9 oz gold per ton and 18 oz silver per ton . Mineralization consists of electrum (Au/Ag) and acanthite (Ag2S).This paper will review plant design and focus on some problems associated with start-up and early operation with the intention of assisting other mine operators by indicating potential problem areas.IntroductionThis paper will discuss operating strategies employed at Baker which improved over-all mill performance. Also included are some ideas which could be steps toward a more efficient operation in a similar setting.Actual dore production by mine life was 37,606 oz gold and 742,117 oz silver.Figure 1 illustrates the relative stability attained over the mine life. Metal recoveries for gold and silver were 92% and 85% respectively.Safety at Baker was of prime importance because of its remote location. Baker received the Mine Safety Association ""Small Mines Award "" in two of its three operating years. At shutdown in late 1983 the mill had operated for over 850 days without a lost-time accident."

Jan 1, 1985

By D. François-Bongareon

"In previous publications by the author, significant advances and generalizations of the theory of sampling of broken ores, prompted and confirmed by experimental results, have been presented. This paper shows how to implement these theoretical results in practice. The models to be used are reviewed, with a description of the various sampling parameters involved. Then the methodology for the experimental assessment of those parameters, including segregation factors, is described in simple and practical terms, along with the use of handy sampling protocol charts. Finally, the particularly important case of processing data from a sample-tree experiment is detailed, and examples of applications covering all situations and types of experiments are provided.IntroductionThe reliability of a sample of crushed material , i.e. the expected (average) deviation between its true grade and the true grade of the lot it comes from, mostly depends upon six factors:• the size (mass) of the sample (and to a minor extent, for small lots, the size of the lot);• the size of the rock particles (degree of comminution)• the nature of the mineralization at microscopic scale (i.e., within even the smallest particles);• the geological nature of the mineralization and mineral of interest;• the grade of the lot in the mineral of interest; and• in some cases, the state of segregation of the lot.In practice, one should first disregard segregation problems, and assess sample variability in the segregation-free case. Once the numerical parameters governing this variability have been assessed, then segregation factors can be assessed in turn. In the case of laboratory standard sample preparation procedures, segregation can usually be disregarded altogether."

Jan 1, 1993

By A. L. Mular

"IntroductionSince the mid -1960s, automatic control of grinding circuits has become the rule, to avoid losses attributable to frequent circuit upsets associated with uncontrolled disturbances such as ore hardness variations. Higher capital costs of grinding equipment and corresponding operating costs-especially with respect to energy consumption-are major factors that continue to stimulate interest in grinding control.Grinding circuit control strategies depend upon the control objectives defined by the processing plant and are subject to constraints such as: maintain final per cent solids within some range, do not transport steel ball s out of the discharge trunnion, or do not overflow or empty the pump box and so on. Constraints depend on the nature of equipment employed within the grinding circuit and may actually determine the characteristics of the control scheme. Typical control objectives are:1. Maintain final particle size at set point by ,a. manipulation of fresh feed rate with circulating load maintained by manipulation of pump box water addition rate, orb. manipulation of pump box water addition rate with circulating load maintained by manipulation of fresh feed rate, where the methodology utilized to accomplish either (a) or (b) is dependent upon equipment/circuit constraints such as the availability of a variable speed pump.2. Maintain circuit throughput at a maximum by,a. manipulation of fresh feed rate subject to constraints on final particle size and variables such as power draw, circulating load and mill overload.3. Maintain mill load at set point by a. manipulation of fresh feed rate subject to constraints such as on power draw.4. Maintain mill power draw at set point bya . manipulation of fresh feed rate subject to mill load constraints. Often, a grinding control objective is dictated by the recovery vs fineness-of-grind characteristic that exists for downstream separation circuits. When recovery is relatively insensitive to size, maximum throughput in the grinding circuit is advantageous.The purpose of this paper is to review control strategies for primary ball mill grinding circuits, rod mill/ball mill grinding circuits and semi-autogenous grinding mill circuits. Primary sensors employed are highlighted and modern trends are documented briefly."

Jan 1, 1989

By B. Burger, T. Bester, S. Deonarain, L. S. Schultz

"This paper details the process followed to raise drill and equip a 6.1 metre diameter vertical service shaft at Glencore’s Mindola Deeps project in Kitwe, Copperbelt Province, Zambia. The project scope comprises a shaft collar, bulk air intake, a pre-sink to -90 metres and raise drilling the shaft from surface to a final depth of 1,892 metres underground, in four separate lifts of approximately 475 metres each. Equipping of the shaft steelwork, headframe erection and commissioning the shaft for hoisting. In addition, the scope included the development of a decline down from 5430’ level underground to the new shaft position on 6205’ level. This paper will provide some insight into the successes and challenges encountered during execution of the shaft works to date and provide some learnings for future projects of a similar nature. INTRODUCTION The Mindola Mine is situated to the west of the city of Kitwe in the Copperbelt Province of the Republic of Zambia (Figure 1). The mine is owned and operated by Mopani Copper Mines Plc (MCM), whose shareholders are Glencore AG (73.1%), First Quantum (17.9%) and ZCCM Holdings Plc (10%).Productivity at the Mindola mine has been adversely affected because of significant ventilation and ore re-handling challenges, which are caused by the dilapidated infrastructure, and design of the existing vertical and sub vertical shaft system. In the circumstances, it was apparent that it was necessary to sink a new vertical shaft that would increase the volume of fresh air down the mine, improving the underground working environment and the current hoisting restrictions, resulting in an increase in productivity and efficiency. Because there were two existing levels ideally situated and perpendicular to one another and because a third level was in close proximity to that perpendicular and because the mine required a ramp down to shaft bottom in any event, consideration was given to raise drilling the shaft as opposed to using conventional blind sinking methodologies."

Jan 1, 2019