Search Documents

By Navid Bahrani

Overview ? Case history of footwall slab failure ? Procedure used to build a finite element model ?? Pre- and post- mining topography ?? Slab geometry ?? Excavation stages ?? Input parameters ? Finite element modelling results ?? Unloading-induced displacements (magnitudes & directions) ?? Calibration of overall model using measured prism displacements ?? Shear stresses and displacements along the base of slab ?? Factors of safety at different stages ?? Effectiveness of rock bolts ?? Staged or unstaged model? ? Conclusion

May 1, 2008

By Paul Ransom

Sullivan Production and Present Value ? Mined 150 million tonnes ? 6.0% Pb, 5.5% Zn, 2 opt Ag, + Sn, Cd, In ? May 2006 Value + US$43 Billion ? 50% of metal from first 37% (55MT) of tons ? True original size ~ 110-120 Mt @ 17%Pb+Zn ? 30MT unconsolidated fill + HW cave

May 1, 2006

By P. D. Soares, H. R. Bullis, R. A. Hureau

"Echo Bay's Lupin Operation has produced more than 2.15 million ounces of gold since start-up in 1982. The mining method used to the£ present time has been longhole open stoping using trackless equipment. Because direct measurement of the open stopes has not been possible until recently determining the exact quantity of unplanned dilution in previously mined stopes has not been possible. Estimates of dilution hove been mode using comparisons between production tons and grades against ore reserve tons and grades.This paper discusses tracking of grade and tonnage measurements from reserve estimation through production. Comparisons between estimated and actual tons and grade are presented~ along with a brief description of methods used at the Lupin operation to control dilution."

Jan 1, 1994

By Ramesh Subramanian

Overview Background / History Undergraduate Programs Mining Engineering Chemical Engineering Mechanical Engineering Graduate Programs and Research Student Enrolment (2002 -) Future Plans

Oct 1, 2010

By X. X. Wu, Q. Zhang, R. H. Fan, Y. J. Feng, J. D. Liu, P. Z. Zhao

In the present study, AA6016 automotive sheets with different grain size were fabricated through changing fabricating parameters, and the effects of grain size on the bendability were studied by bending test and optical microscopy. The results showed that the sheet with coarse grains exhibited poor bendability, and some micro-cracks were revealed at the surface of the bending samples. While the sheet with fine grains exhibited good bendability, and the bending samples showed smooth surface. Shear bands on the cross section of bending samples were observed. It was found that samples with coarse grains had more shear bands. These shear bands distributed in bundles, which facilitated the formation of continuous neckings and micro-cracks. However samples with fine grains had less shear bands, which distributed uniformly. The decrease of grain size could not only hinder the formation of shear bands, but also improve the homogeneity of its distribution during bending. On the other hand, refining grains could increase the amount of grain boundaries, which impede the propagation of shear bands. Hence the decrease of grain size could hinder the formation of continuous neckings and micro-cracks during bending, resulting in the significant improvement of the bendability.

Jan 1, 2015

By Nathan Ferdinands

Outline Overview of Site and Partners ?MeanduMine ?Thiess?GroundProbe Technology ?Work Area Monitor (WAM) ?Software control ?Alarms MeanduMine King2East pit failures ?Background, and Northern Failure ?Southern Failure Recovery and conclusion

Nov 1, 2011

By A. Klingberg, M. Svensson, N. Smolko Schwarzmayr

"Removal of silicates and carbonates from sedimentary phosphate ores by the use of new synthetic collector/formulations was investigated in a comparative study with traditionally used collector systems as references. In the direct carbonate flotation the new formulations showed higher efficiency, contributed to an improved balance of P2O5 recovery and P2O5 enrichment in the recovered material. Efficiency of the new formulations containing synthetic surfactants was 1.5–2 times better than potassium salt of fatty acid sulfonate based formulations that are traditionally used for that purpose. The new formulations also provided up to 7% increase in P2O5 recovery at the same P2O5 grade. The new synthetic collectors for removal of silicates showed extremely good selectivity towards silica bearing minerals. The selectivity factor for the flotation tests when new formulations were used was 32–52 and for the flotation tests with the traditional collectors: 20–32. The ratio between distribution of an amount of silicates (as SiO2) and distribution of phosphate in the froth (waste) is defined as the selectivity factor. The new formulations provided more than 2% decrease of the amount of SiO2 at the same P2O5 recovery.INTRODUCTIONPopulation growth and decrease of arable land are the main reasons for constant increase of consumption of apatite (phosphate ore) in the fertilization field (Lannefors, Gorochovceva, Klingberg, Lima, & Gustafsson, 2015). Fertilizers play a key role for farmers to produce more with less land. The phosphate component of the fertilizer is vital for producing healthy and large amount of crop. As a result the demand for phosphate rock is growing.The largest producers of phosphate rock are the Unites States, Morocco, Tunisia, China, Russia, and Brazil. The term “phosphate ore” includes all phosphate-bearing minerals and rocks, but only two of them are of industrial interest: apatite (igneous origin) and sedimentary phosphate (Peres, Araujo, El-Shall, Zhang, & Abdel-Khalek, 2007). The majority of the world’s phosphate deposits are of the sedimentary type. There are two different types of sedimentary phosphates: siliceous and carbonaceous which are categorized based on gangue minerals (such as quartz, carbonates, mica, and clay)."

Jan 1, 2016

By G. R. MANSON

The Brisco Barite Mine lies 70 km south-southeast of Golden, British Columbia. Barile mineralization occurs in a northstriking brecciation zone within Ordovician-Silurian Beaver/ oot dolomites and quartzites. Brecciation was caused by faulting related to the Mount Forster-Steamboat Fault. The main barite vein occupies a fault zone and is up to 12 m wide and over 250 m long. It is light grey to white, fine grained and compact; BaSO4 content is 9/. 70 per cent. Production started in 1945 and has continued to the present. Barile originally was removed from an open pit; later, an adit, begun in 1957, reached more than 240 m along the vein, 15 m below the pit floor. Today ore is hoisted from a decline resting some 37 m below the pit floor.

Jan 1, 1984

By J. W. M. Porritt, K. C. Cheng

Knowledge of radon emanation rates from uranium-bearing rocks is essential to the design of mine ventilation systems for uranium mines. Measurements of equilibrium ratio between radon and its daughters in mine air are important for a better control of mine radiation conditions. The concentrations of radon and daughters were monitored at cut-and-fill stopes in the Beaverlodge Mine of Eldorado Nuclear Ltd. during all phases of the mining cycle. The radon emanation rates of ore and rock samples were measured at the laboratory and the results were compared with in-situ emanation tests in an isolated ore drift. Samples of backfill solution, backfill drainage and ground seepage water were measured [or radon and analyzed for radium and uranium. The results showed that discharges of backfill solution and daily shift-end blasts were the two major sources for a rapid release of radon gas in the ventilation air. Other mining operations, such as drilling, mucking, etc., contributed little effect on radon release to the mining environment. Radon emanation rates of the Beaverlodge are samples ranged from 13 x 10-18 to 600 X 10-18 Ci/cm2/ sec and that of waste rock samples from 0.54 x 10-18 to 13.4 X 10-18 Ci/cm2/sec. The in-situ emanation rate of mine walls with ore-to-rock ratios of 1 to 7 was 60 x 10-18 Ci/cm2/sec. The average equilibrium ratio of radon and its daughters in stapes was 32.6%. Under a normal ventilation condition, the average background levels of radon concentration in cut-and-fill stopes ranged from 13 to 80 pCi/L. The discharges of backfill solution during backfill operations at 100 tons solids per hour released approximately 1.8 x 106 pCi/min of radon and elevated radon concentration in stapes 2 to 5 times above the background levels.

Jan 1, 1981

By P. Su

Friction stir spot welding of a range of Mg-alloys is investigated (AZ91, AZ31, AM50 and AM60). The peak temperatures during friction stir spot welding of all Mg-alloys are close to their solidus temperatures. Also, the apparent material viscosity of Mg-alloy sheet is lower than that when Al-alloy sheet material is spot welded. This is important since it means that the widths of the stir zones forming during spot welding of Mg-alloy sheet are smaller than those when Al-alloy sheet is welded (when identical welding parameter settings are applied). These lower apparent viscosity values must be taken into account during numerical modeling of the Mg-alloy spot welding process. The efficiency of energy utilization is very low when Mg-alloy sheet is spot welded and is of the same order as that when fabricating Al-alloy sheet. The energy generation contributions of the rotating pin and the tool shoulder are investigated. When the spot welding operation is carried out without the application of a dwell period, the contribution made by the rotating pin vis-à-vis energy generation is around 66%. The contribution made by the tool shoulder increases to about 65% when a dwell period of four seconds is incorporated during the spot welding operation. This increase results from a longer contact time between the tool shoulder and material within the stir zone, The failure load during overlap shear testing increases when the bonded area and the energy input increase during spot welding. Sample failure initiates from unbonded regions and from discontinuities at the edge of the stir zone. The formation tendency of discontinuities is increased when Mg-Alloy sheet is spot welded because of the limited deformation characteristics of the base material at lower temperatures.

Jan 1, 2006

By E. A. Rychkun

"For the last 700years of recorded economic history, man has been subjected to alternating inflationary and deflationary patterns. Through this period of time, a severe deflationary pattern has developed approximately every 55 years, creating 12recordable occurrences. Through the last two centuries, this severe deflationary phenomenon has come to be known as a depression. As these depressions have repeated themselves regularly, they are cyclic. This in turn leads to the question of whether the 13th cycle will also repeat itself in the form of a depression. As this cycle is now 51 years old, we must consider the possibility at about 1984.In analyzing a 700-year record of consumer prices in Southern England, the 55-year cycle appears to vary in shape and intensity. This varying phenomenon is due to the effect of longer cycles upon which each one ""rides "". Because each cycle effectively rides on the next largest, which in turn rides on the next largest and so on, the combined measured effect of all cycles together at any point in time is always unique. This means that anyone cycle can never repeat itself in an exact identical manner. The combined effect therefore is what we observe in the form of prices and, as cycles interact, variations in deflation are produced . The ""science"" of economics attempts to quantify and develop theory on situations which are never identical and hence can be conservatively classified as a useless predictive tool.This means that more unconventional approaches may be required to predict our economic future. In looking at previous depression cycles, it is possible to recognize similarities in human behaviour patterns and hence the resulting economic movements. These behaviour patterns create major events or influencing factors which set the scene for a major deflationary condition. The way in which these factors occur, however, is not predictable. As more and more of these similar events are identified in each cycle, we can increase our confidence on the probability of the last event occurring (a depression). By also unravelling the set of larger cycles, we can determine the potential combined effect at any point in the future.This paper presents a system of cycles ranging from 800 years to 3 years which appear to operate in our economic system. By so doing, a long-term projection into the next century can be made. Finally, the paper deals with the main controlling similarities within the depression cycle, to show that a comparison with our current cycle implies that a major deflationary collapse in the mid 1980's is virtualy inevitable."

Jan 1, 1980

By B. M. Das, F. Claridge, V. K. Garga

Coal, as well as a large part of other minerals in Canada, is produced by surface mining methods. This has resulted in short and long-term accumulation of waste rock in dumps. Two main problems arise from the flow of water through these dumps: stability of dumps and the impact on stream flows. In recent years, a number of mines have started placing waste rock in valleys for general disposal or far constructing mine access road ways. All these have created challenges in the following areas: effective design of dumps and flow-through dams; stability monitoring of the structures; environmental impacts downstream by way of increased amount of fines in suspension, sedimentation, and toxic substances; and long-term status of flow and flood. Similar situations also exist in many civil engineering structures. This paper discusses the status of rock drains and the immediate and future research needs.

Jan 1, 1990

Agenda ?Introduction ?Geology ?Mining ?Metallurgy ?Process, Layout ?Environmental Background ?Kinross Gold Corporation owns the Lobo-Marte gold property, located in Region III of northern Chile. ?The property is close to two other Kinross mines, Maricunga 50kmto the south and La Coipa 60km to the north, plus a regional office in Copiapo and district level operating synergies are expected. ?Lobo and Marte were discovered in the early 1980s and are intrusion-hosted, porphyry-type precious metal deposits, typical of the Maricunga District. ?The Marte open pit heap leach mine was in commercial production in late 1988, but was suspended in February 1992 as it did not meet forecasted production levels and recoveries. ?Kinross plans to recover ore from the Lobo and Marte deposits through an open-pit, heap leach47,000tonne per day operation.

May 1, 2010

By H. Warren Newcomen, Dennis C. Martin

"This paper describes the investigation of a large, progressive slope failure on the southeast wall of the east pit at Highmont Mine, British Columbia Geotechnical investigation s consisted of geological and structural mapping, assessment of blasthole drilling records, review of rock core information, slope movement monitoring and back analysis of various possible failure modes. Climate records and mining history were also assessed to determine their relationship to slope movement .Analysis of movement monitoring records and geotechnical information indicates that the failure is deep seated. The upper portion of the failure surf ace occurs along clay filled discontinuities. The lower portion of the failure surf ace appears to occur through the highly altered rock mass. High groundwater pressures and mining at the toe of the slope are documented to have had a major influence on stability at various times during the failure. Stability analyses results are presented and possible remedial measures are discussed.IntroductionHighmont Mine is located near Logan Lake in the Highland Valley approximately 50 km southwest of Karnloops, British Columbia (Fig. I). Mining of the porphyry copper and molydenum ore bodies began in 1980. In May, 1983, when mining in the east pit had progressed to a depth of about 60 m (200 feet) , a failure (designated the Southeast Failure) began to develop in the southeast corner of the east pit. Subsequent mining to a depth of 110m (360 feet) was accompanied by frequent and substantial slope movements involving between 500000 and I 000 000 m3 of rock . The slope was monitored extensively to assess short-term movement trends for operational safety. Geological mapping, core logging and rock mechanics testing were used in conjunction with the long-term monitoring information to determine the failure mechanism, conduct stability analyses, assess the effects of instability on pit design and enable design and installation of remedial measures."

Jan 1, 1988

By A. M. Cann, C. I. Godwin

"The Kemess porphyry copper-molybdenum deposit occurs in the Intermontane Belt of north-central British Columbia. The deposit is in andesitic to basaltic flows and tuffs which may be correlated with the Savage Mountain Formation of the Upper Triassic Takla Group. Most known chalcopyrite and molybdenite is associated closely with a 500-m-diameter zone of intense quartz-sericite-pyrite alteration. A zone of supergene enrichment, up to 30 m thick, underlies a leached capping about 20 m thick. The age of mineralization and the surrounding granodiorite and quartz monzonite pluton is Early Jurassic. K-Ar and Rb-Sr analyses indicate that the mineralization and alteration is slightly younger (l82±6 Ma) than the granitic intrusion (KAr: about 205±6 Ma; Rb-Sr: 190±4 Ma). The low 87Sr/J6Sr initial ratio for the granodiorite is typical of plutons in the Intermontane Belt.IntroductionKemess is a medium to small porphyry copper-molybdenum deposit with significant gold and silver values (Pilcher and McDougall, 1976). This paper describes the lithologies and alteration at this property; geochronology by Rb-Sr and K-Ar methods defines the ages of mineralization and surrounding plutons to be Early Jurassic.The property, located in the Thutade Lake area of northcentral British Columbia (NTS Map 94E; lat. 57°04'N; long. 126°44'W), is about 425 km northwest of Prince George (Fig. 1). Closest road access is 35 km southeast of Kemess. Final access must be by float plane or helicopter. The British Columbia Railway right of way passes 70 km to the southwest of theproperty.A prominent gossan zone at Kemess was staked in 1967 by Kennco Explorations (Western) Ltd. following detection of geochemical anomalies during stream sampling the previous year. During 1968, 1969and 1971, Kennco completed 232 m of X-ray diamond drilling, conducted geological mapping and carried out geochemical sampling of silts and soils (Stevenson, 1969; B.C. Ministry of Energy, Mines and Petroleum Resources, G.E .M., 1969 and 1971). Getty Mines Ltd. optioned Kemess in 1975and 1976. They remapped the area and diamond drilled 12 BQ and NQ holes, totalling 2065 m (B.C. Ministry of Energy, Mines and Petroleum Resources, Expl. B.C., 1975)."

Jan 1, 1980

By H. N. Tran, D. Barham

"A systematic survey of the appropriate literature in terms of phase equilibria and possible reactions involving deposits in Municipal Solid Waste (MSW) incinerators are analyzed particularly with respect to the theoretical first melting points of typical ashes and the possible presence of a liquid phase at the temperature of ash-metal interface. Conclusions are drawn on the basis of the possible presence or absence of various metal chlorides and sulphates in such situations, and their effects on the problems of fouling and metal corrosion. From preliminary results, it would appear that ZnCl2 is unlikely to be present in any molten phase which causes corrosion because it evaporates rapidly from such liquids. It would also appear that PbCl2 and, by inference, ZnCl2 will sulphate at relatively low temperatures if the flue gas contains SO2 and O2.IntroductionMunicipal Solid Waste (MSW) incinerators produce fly ash which deposits on heat transfer surfaces throughout the furnace, leading to corrosion and loss of energy recovery efficiency. Despite a massive amount of research carried out on the subject of corrosion in MSW incinerators, the problem of corrosion of heat transfer metal is still with us, and no definite over-all cause and effect relationship has yet been identified. In order to make a contribution to the eventual solution of this problem, the authors have examined the problem from the beginning, using their knowledge of fouling and corrosion problems in black liquor recovery boilers as a starting point.The incineration of MSW has been used for many years to reduce the volume of material sent to landfill (ash volume compared to raw waste volume), and, in most cases, to recover energy at the same time by raising steam The steam may be ""low- or high pressure/ temperature"" depending on its end use. The higher the steam pressure and temperature, the greater seem to be the problems with corrosion of heat exchanger metal, presumably because the metal must withstand higher surface temperatures.The chemical and physical composition of MSW is extremely variable, not only on a regional basis, seasonal basis, and day-today basis, but also on a minute-by-minute basis, due to the inhomogeneity of MSW. This makes it extremely difficult to define cause and effect relationships, because both cause and effect are transient in nature."

Jan 1, 1991

By P. R. Geoffroy

Extensive and Intensive Prospecting As often pointed out, the search for new ore deposits may be carried on along two widely divergent lines. It may be either extensive or intensive. By extensive prospecting we mean a search for mineralized outcrops conducted over large and more or less virgin tracts of land, followed by a test of the practical value of any discovery made, the test being limited to the immediate vicinity of the outcrop. Extensive prospecting, was, in fact, the only policy known to the early prospectors. of the American continent and is still the rule in the remote sections of the Canadian Shield and in the African wilderness. It can be further characterized by the lack of emphasis placed on geological and other technical means as an aid to the search for ore. However, very little virgin ground is left, nowadays, for a man or a company to test their luck, and whatever is left is so remote from the necessary means of development that any new discovery will require considerable delay and expenditures to be amenable to profitable mining. On the other band, a great many of the favourable and still unexplored areas (and this is particularly true in Canada) are overburdened to such an extent that outcrops of bed-rock are extremely scarce and extensive prospecting is nearly impossible. Intensive prospecting, to the contrary, must be understood as a detailed search for ore carried on over limited areas in districts already known to be mineralized and covering regional structures whose relation to mineral deposits bas been estahlis.hed with a fair degree ot certainty. The search for deep-seated deposits in the vicinity of successful mines is a perfect example of intensive prospecting. As a matter of fact, the majority of the geologists employed by the mining industry are engaged in some kind of intensive prospecting.

Jan 1, 1950

By S. McCarthy, K. E. Waters, A. Jordens

The beneficiation of rare earth (RE) element bearing minerals has become an active area of research as applications for these elements grow while the supply to non-Chinese consumers is restricted by export quotas. One of the most interesting beneficiation techniques for RE minerals is froth flotation as their unique chemistry suggests that collectors with a specific affinity for RE cations should be able to selectively recover these minerals. Existing literature, focusing mainly on bastnäsite flotation, identifies hydroxamic acids as excellent collectors for RE minerals. The high stability of hydroxamate-RE cation complexes is the explanation most often offered for the observed selectivity of these reagents in bastnäsite flotation however some research has also suggested that mineral solubility plays a crucial role in the success of hydroxamic acid flotation of RE minerals. This work investigates the interaction of allanite, a relatively insoluble RE-silicate mineral, with benzohydroxamic acid using zeta potential measurements and microflotation. The effects of Fe(III) and Fe(II) ions as potential activating ions (cations that form stable hydroxamate complexes) on benzohydroxamic adsorption to the allanite surface are investigated as a potential solution to promote hydroxamic acid adsorption. The results indicate that the optimum conditions for separation of allanite from quartz occur at pH 4 using FeCl2 as an activator for benzohydroxamic acid adsorption.

Jan 1, 2014

By C. Mills, A. O. Burt

"The paper examines the role of gravity concentration in both an historical context and within the modern mineral processing industry. It discusses the principles of the process on both a theoretical and practical level. The importance of more mineralogy and its effect on the choice of the wide range of equipment available is discussed. The paper concludes with a discussion on the relative merits of gravity concentration with other forms of processing.IntroductionIt is an unfortunate, albeit popular, misconception among otherwise enlightened engineers in the mineral processing industry that gravity concentration was a process developed in the dark ages, perfected in the middle ages, and abandoned in the modern ages.Gravity concentration was developed in the dark ages - long indeed before that. Agricolau: cited examples of gravity concentration, crude examples admittedly, being practiced over 3000 years ago. However, gravity concentration is not dead. Far from it. As recently as 1978 it was reported that the total mineral tonnage treated by this process in the United States was greater than that processed by flotation. Coal represents the bulk of the or e treated by gravity separation in the U.S.A., with iron ore representing a major portion of the balance."

Jan 1, 1985

By D. F. Malan

"This document highlights some of the topical problems associated with the design and support of deep tabular excavations in hard rock. The displacement discontinuity boundary element method has been used for at least five decades to analyse stress and displacement distributions around narrow width excavations with complex plan outlines. The assumption is made in most cases that the rock mass surrounding the excavation is perfectly elastic. Although this approach works well to minimise stress concentrations in practice, it has limitations as important parameters, such as the effect of mining rate, cannot be investigated. Recently, a limit equilibrium model has been studied as a means to enhance standard layout design exercises by including an interactive on-reef damage model. This approach can include explicit energy release dissipation computations. A second problem faced by engineers in the mining industry is the evaluation of pillar and remnant stress. The paper highlights two aspects namely the effect of element size in displacement discontinuity modeling on pillar stress and the difficulty to estimate the effect of total closure on the regeneration of stress in old mining areas. Regarding the support of the tabular excavations, current efforts are focussed on providing improved aerial coverage using hangingwall bolting and temporary nets. An unresolved issue is the installation of permanent mesh in low stoping width areas. INTRODUCTIONSince 1886, more than 50 000 tons of gold has been mined in the Witwatersrand Basin of South Africa (Hartnady, 2009). The nearby platinum mines also saw significant growth in recent years and more than 80% of the world’s platinum group metal reserves are contained in the Bushveld Complex of South Africa (Nell, 2004). Apart from the economic aspects, the mines served as an outstanding rock engineering “laboratory” for many decades owing to the deep, tabular nature of the excavations. The period from 1960 to 1980 was especially lucrative in terms of research and world-renowned researchers investigated the support and rockburst problems (e.g. see Cook et al., 1966; Salamon, 1968; Bienawski, 1973; Wagner, 1984). Many of the rock-related problems nevertheless persist up to the present day and this paper explores some of these problems and recent progress. The production of gold declined substantially in recent years (Hartnady, 2009) and well-directed rock engineering research can play a meaningful role to slow this trend. The objective of the document is to highlight critical areas requiring additional research and not to discuss the topics in detail. The reader is referred to the many references for additional information. The paper only focuses on three areas namely numerical modelling, pillar stress estimation and aerial support. Although these are diverse topics, it is included in one paper to illustrate the many unsolved and practical problems associated with deep tabular excavations."

Jan 1, 2015