Search Documents

By D. R. Hatton

To obtain sufficient material on which to perform copper-molybdenum separation testwork a variability set of drill hole reject samples amounting to several tons was put together to include the different ore types proportions expected in the copper circuit. The samples were treated in a copper circuit pilot plant and enough mass of bulk concentrate was recovered to conduct copper moly separation tests in the laboratory. Tests consisted of stage flotation reactor (SFR) rougher pilot plant tests, conventional laboratory rougher, cleaner and 4 stage open circuit cleaner tests. The mineralogical liberation analysis of the feed and concentrate was used to model the effect of liberation on the grade-recovery relationship of the different samples. Mineral kinetic parameters for the various samples were determined by calibration to the test data. The copper concentrate results as simulated from previous studies on the same deposit were used to simulate the variability in head grade and throughput expected for the feed to the copper molybdenum separation circuit for each of the first 10 years of production. This variation in feed was then simulated through the separation circuit to obtain optimised molybdenum grade recovery curves to forecast the circuit production for each of the first 10 years. INTRODUCTION Incorporating Geometallurgy into the design for a copper molybdenum separation is especially challenging due to the low mass of final concentrate typically produced during testwork. This is due to the low molybdenum head grades and high overall molybdenum upgrading expected. With molybdenum head grades of around 300 ppm, 1 tonne of copper circuit feed is expected to produce around 300 g of molybdenum concentrate in the plant. In the laboratory however, this may end up only resulting in a few grams. Obtaining sufficient mass for laboratory testing therefore requires starting with a large initial sample and careful testwork planning to maximise the utilisation of this mass. A testwork program was designed to investigate the effect of ore variability on the copper molybdenum separation circuit (here after referred to as the molybdenum circuit). Composite samples were selected to represent the various ore types, copper content, moly content, pyrite content and clay contents expected in the copper circuit feed. These samples were run through a bulk copper pilot plant to create the feed for the molybdenum testwork. The molybdenum testwork consisted of rougher kinetic flotation tests, rougher cleaner kinetic tests, rougher cleaner kinetic tests with regrind, stage flotation reactor (SFR) pilot plant tests, open circuit cleaner tests. These tests were used to calibrate the ore kinetics in the IGS-FLEET model for simulation of the molybdenum circuit performance.

Jan 1, 2019

By F. Charette

The paper reviews the requirements of the instrumentation required to monitor mining excavations in a high stress environment, and the development plan to instrument the D-Bolt in such a fashion as to be able to follow the behaviour of the bolts in relationship to the ground movements and support performance. Recent field observations of D-Bolts under static and dynamic conditions are also presented. Also discussed is the assumed mechanical behaviour of the D-Bolt. D-Bolts are used in two (2) Canadian underground mines operating in high stress environments and tested in three (3) other operations.

Jun 1, 2012

By W. R. Tyson

Imperfections such as lack-of-fusion and undercut are inevitable in field welding of pipelines. Above a certain size, such defects must be removed or repaired. In the present state of the art, determination of allowable defect size is done by Engineering Critical Assessment (ECA). This requires measurement of toughness, and comparison of toughness with crack driving force. ECA methods used in current international pipeline standards will be reviewed and compared.

Jan 1, 2010

By L. G. Smith, C. A. Shook, W. H. W. Husband, W. Schriek

"The flow of slurries in pipelines is governed by many variables, and the study of the influence of each of these variables is difficult, if not impossible, in some cases. Many correlations are available which fit data within a given range. However, no one method is yet available to design a slurry pipeline for all desired conditions without at least some physical measurements on the slurry itself. For this reason, the slurry pipeline facilities at the Saskatchewan Research Council have been developed during the past 12 years and it is hoped that the development will continue until the process is thoroughly understood and test facilities are no longer necessary. This paper outlines methods currently used and under development at the Saskatchewan Research Council for measurement, control and study of the variables governing the flow of slurries."

Jan 1, 1973

By S. M. Moon

Today, underground exploration is spotlighted as an infinitely developable area. For this purpose, many tunneling technologies were created. And until this very day, many techniques are being developed for more efficient underground movement. Although previous technologies have been developed and now being used in various forms like TMB, struck propulsion method and hydraulic propulsion method, it is hard to find a robot type exploring in small scale. But development of small scale underground exploration robot is a promising research subject for its usage in examination of soil, mineral, and subterranean resources, investigation of hazardous regions, and the military. So we developed a robot that can dig and move underground, inspired from the motion of earthworm and mole cricket. Earthworm and mole cricket dig the soil in the front and draw it off backward, so that they can move forward. We developed a mechanism that uses 2 rotating solid of revolution (bits) for pulverizing the firmly united soil in the front and put it inside the body. The bits rotate in the opposite direction of each other. While moving forward, the soil in the front moves along the spiral on the bit and is saved inside the body. The soil saved inside is taken out through an outlet in the back by a ventilation system. The ventilation system on the ground blows through a hosepipe connected to inner part of the robot and the air blows off the soil. The moving mechanism of exploring underground can be classified into 2 parts. One is to fix the blade link on the soil in a form of 4-bar link. The other one is to move forward rotating the whole link. When the blade link system for movement rotates a certain degree, one blade link is fixed, while the other one is folded in. When 2 blade links of different length rotate as it is, different torque is applied on each link. By the law of action and reaction, the link that has larger torque leads the rotation and movement.

Aug 1, 2013

By C. Sist, J. Shannon, J. Fossenier, J. F. Adams

With the cleanest and easiest to treat copper concentrates dwindling and becoming harder to find, electrorefineries must deal with the reality of higher impurity anodes. There are well-known strategies for managing nickel, bismuth, antimony, etc. using bleeds (Ni, Bi, Sb, As) or arsenic control (Bi, Sb) or hydrometallurgical add-on circuits (IX, MRT, SX for As, Bi, Sb). However, for integrated copper producers and those producing other base metals it is often worth considering a more holistic, global approach. This paper will discuss both the well-known strategies as well as some global strategies and the role that hydrometallurgy can play in them. Examples will include atmospheric and pressure leaching, selective precipitation and impurity recycling or fixation. INTRODUCTION In the electrorefining of copper, impure copper anodes are electrically corroded, and pure copper is deposited on cathodes by passing DC current through an acidic copper sulphate solution. The anode copper impurities either settle to the cell bottom as insoluble components (anode slimes) or remain in solution with minimal deposition at the cathodes when correct operating parameters are maintained. Consideration of impurities is important in all copper electrorefineries. A typical impure anode contains 98.5–99.5% copper (Schlesinger et al., 2011). Table 1 shows the range of impurities reported for all copper anodes in the 2007 survey of operating refineries (Moats et al., 2007). Also shown is an approximate “limit” of anode compositions within which the majority of refineries operate without additional impurity removal capacity (beyond conventional liberator/bleed circuits). The column is somewhat subjective and meant to be an approximation only since there are many factors that influence impurity deportments and refinery impurity tolerances. More recent world survey data from 2013 show the averages for all impurities trending upward from 2003 to 2013 (Moats et al., 2013). With a competitive market for good concentrate and more copper recycling from electronics (which contain high levels of impurities such as nickel, lead and antimony), this trend is expected to continue through the coming years. The traditional primary method of impurity control is refinery bleed through liberator cells which are employed in the vast majority of refineries (Moats et al., 2013). These are used to control copper (primary liberators), nickel, arsenic, antimony and bismuth (secondary and tertiary liberators). Other methods of impurity control include arsenic addition (upstream in the smelter deporting to anode or directly to electrolyte) to control antimony and bismuth (Kamath et al., 2003), ion exchange or molecular recognition technology (Hur et al., 2005; Navarro et al., 2012) for antimony and bismuth. Many refineries also operate nickel evaporators to remove nickel sulphate before recycling back acid. Some use, or are contemplating using, acid purification units to recycle acid and arsenic without nickel and making nickel carbonate (Kamath et al., 2003; Sheedy et al., 2006).

Jan 1, 2019

By M. Thérien, M. Rémillard

"Data from two industrial plants are treated by mass balance package BILMAT. The first application concerned a base metals/precious metals (PM) producer and the second, implementation of a hydrocyclone for the recovery of iron chips in the granite industry. Also LOTUS 123 software can easily be adapted for laboratory test mass balances using an IBM-PC computer. INTRODUCTIONThe present paper deals with two different BILMAT program applications. The first application concerns a copper-zinc-gol d-sil Yer producer based in North-western Quebec and the second, concerns the iriplementation of a hydrocyclone for the recovery of iron chips in Quebec granite company.Afterwards, we deal with some LOTUS 123 software applications for laboratory test mass balances using an IBM-PC.1. Base metal and P.M. producerNoranda Inc, Mattagami division, which operates mines in North Western Quebec, produces copper and zinc concentrates from a sulphide ore. Small amounts of gold (0,34 g/t) and silver (20 g/tl are present. At the time of the study, only 30% of the silver content was recovered in the copper concentrate. The main objective of this study is, to evaluate the metallurgical behaviour of silver in the flotation circuits, to increase its recovery in the copper concentrate and therefore to improve its final economic value. It is then worthwhile to identify the silver bearing minerals and to determine the critical flotation stages where they are lost. The methodology proposed is based on the coupling of a mineralogical study and a detailed mass balance ca1cu1ation in the flotation circuit performed using the BILMAT mass balance package (1, 2, 3).The results are discussed with respect to the distribution of silver in the circuit. The recoveries obtained at the various separation stages for the minerals present in the ore are also discussed."

Jan 1, 1987

By A. Pawelczyk, D. Hreniak, E. Zych, W. Strek, K. Grabas, A. Ostrowski

"Mongolia is a country rich in rare earth resources. In the experiments carried out samples of the Mongolian ore were processed to obtain a lanthanide concentrate. The concentrate underwent hydrometallurgical processing. At the same time radioactive elements were removed. The lanthanides were obtained in the form of hydroxides that were further processed in order to get concentrated products. As a result cerium, lanthanum and neodymium-praseodymium concentrates were separated in the process. Also a concentrate of remaining elements: samarium, europium, gadolinium, terbium, dysprosium, holmium and erbium was obtained. INTRODUCTIONAccording to the assessment of the US Geological Survey, Mongolia possesses 16.77 % of the world total rare earth (RE) resources (Daly, 2011); that is the second largest RE reserve in the world, estimated to be 31 million tonnes in terms of rare earth oxides (REO). In the face of Chinese RE trade restrictions, Mongolia emerged as an important economical partner in mining and exploitation of these critical raw materials. This country is recognized as having more than five large RE deposits in the southern provinces. The most important are Lugeengol (Lugin Gol), Mushgia Khudag, Khotgor and Khalzan Buregtei (Eurasia, 2010). The Mongolian government has taken measures to facilitate western investments, nevertheless the country is economically dependent on China, the basic trading partner, particularly where exports are concerned.In the late 1970s Hydromet Kowary Enterprise, Poland, took up, along with the Wroclaw University of Technology, research and technological study on lanthanides recovery from raw materials of Vietnamese and Mongolian origin and from Indian monazite sands (Kowalczyk, 1990; Kowalczyk & Mazanek, 1987; 1990). For that purpose, a rare earth processing plant had been constructed with the capacity of about 10 t/year of hydroxide concentrate. The facility included several technological operations like grinding, flotation, hydroxide concentrate production in the hydrometallurgical processing, particular RE separation, and production of commercial products in form of CeO2, La2O3, Nd2O3, Pr2O3, and misch metal. Additionally work had been carried out in Kowary on the manufacture of yttrium and europium oxides of high purity, which were intended for color TV picture tube production in Poland."

Jan 1, 2012

By A. Chieregato, C. G. Oñate Salazar, D. Martinelli, D. Peila, M. Barbero

This paper is aimed to confirm the possibility to excavate fractured rock masses by using EPB shields, even in presence of relevant water tables. This verification is based on laboratory test experiences carried out at TUSC laboratory of Politecnico di Torino, where the natural material is tested in order to verify the suitability of a certain conditioning technique in particular conditions. This is due to the fact that every case should be studied apart from existing studies on a certain rock type, as other factors such as fragmentation of the rock mass, natural water content and porosity of the rock can considerably influence the final result of the conditioning process. The most important aspects that allow to consider the conditioning of fractured rock masses as suitable are: possibility to create a plastic paste that can transmit the pressure at the front in a effective way; reduce the permeability of the spoil material in order to reduce the possibility of water leakage inside the chamber and eventually in the tunnel; verify the consistency of the conditioned material for the extraction through the screw conveyors and the belt conveyors. For this research an argillitic schistose rock mass, with some quartzitic and calcareous inclusions, has been studied by using different level of conditioning in order to verify the suitability of an eventual EPB excavation through this formation.

Jan 1, 2015

By A. A. Rogozhin, E. G. Likhnikevich, S. I. Anufrieva, A. V. Kurkov

The Beloziminskoe deposit in Siberia is a large, potentially productive deposit of rare metals contained in ochreous apatite pyrochlore ores formed by weathering of a carbonatite. The ores are composed of pyrochlore, columbitized pyrochlore, monazite, apatite, magnetite, ferric and manganese hydroxide, titanic iron ore, zircon, hydromica, quartz, feldspar, and carbonates. A gravity-flotation enrichment flowsheet with application of cationic and anionic collectors has been developed. This flowsheet allows for obtaining a pyrochlore concentrate containing 44.3% Nb2O5 and 1.89% P2O5 with recovery of 55.83% Nb2O5 as well as an apatite concentrate containing 39.2% P2O5 and 1.05% TR2O3 with recovery of 62% P2O5 and 43.23% TR2O3 from ores containing 0.92% Nb2O5, 16.9% P2O5 and 0.6% TR2O3. Rare-earth concentrate containing 40% TR2O3 with recovery of approximately 10% TR2O3 was obtained at the same time. Major losses of valuable elements are related to slimes, which make up more than 50% of the ground ore. The niobium concentrate does not meet the phosphorus and radionuclide concentrations needed for the production of ferro-niobium. Acid leaching and sulfatization provided a high level of phosphorous and radionuclide removal. Conditions include hydrochloric acid pre-leaching at 75- 80°C with an 18% HCl solution for four hours and low-temperature sulfatization of acid-leached concentrate at 160-180°C for one hour followed by water leaching of the residue. The apatite concentrate could potentially be processed using nitric acid leaching. This technology is based on decomposition of apatite concentrate with 55-57% strength nitric acid with transfer of rare-earth metals into solution in the form of ammonium phosphate. This technology recovers a rare-earth concentrate containing 95% TR2O3 with extraction of 86%, and highly concentrated polynutrient fertilizer (ammophos) with phosphorus extraction of 95%. The completed research shows how complex multicomponent ores of residual soil may be processed for the extraction of niobium, phosphorus, and rare-earth products.

Jan 1, 2016

By G. Vibert Douglas

IN a previous paper by Douglas and Gillies (1), a simple field test was given for gold. Later work by the present writers, and by others who have kindly written to us, shows that the test is not as satisfactory as it was hoped. In many cases, the gold mirror is completely obscured by a dense precipitate which, up to the present, it has been found impossible to remove. After many attempts, we have temporarily given up the iodine test and have been working on a simple pyridine reaction based on the work of Putnam, Roberts, and Selchow (2): The ore to be tested is ground to a fine flour. Place half a gram of this powdered ore (an amount that will cover a Canadian ten-cent piece, not heaped) in a six-inch test-tube and add 5 c.c. of aqua regia. The aqua regia. should be made up on each occasion, using four parts of hydrochloric acid and one part of nitric acid, both concentrated. Shake the solution in the test-tube for about one minute and allow to settle until dear. The rime to settle may be 30 to 60 minutes. When dear, a drop of the solution is with-drawn with a fine, dean eye-dropper or capillary tube and placed on à small glass plate. A slide such as is used for mounting rock sections is suitable. Now place an equal sized drop of pyridine solution on the plate beside that of the aqua regia solution to be tested. The pyridine solution, containing nine volumes of hydrogen bromide to one volume of pyridine, can be made up in advance and carried in a glass-stoppered bottle. Join the two drops with a glass thread or fine, dean stick, and allow the merged drops to stand undisturbed. I t is well to place the slide on a piece of white paper so that the presence of the crystals which may form can be easily seen. The time for their formation will vary with the amount of gold present, but the slide should be allowed to stand for at least 30 minutes before negative results are reported. A hand lens of at !east ten magnifications is essential. If gold is present, minute red crystals will form around the margin of the drops as these drops slowly evaporate.

Jan 1, 1938

By K. MacMaster

"This paper deals with the history, development, present and future of the Employee Assistance Programs in place at the Inco Ltd. operations in Thompson, Manitoba. It should be noted that, although many similar programs exist in various industries and jurisdictions, these programs had to be fine-tuned to meet the needs of Inco employees, having in mind the helping professional resources available in Thompson and its geographic location. IntroductionIn the late 70s, many Canadian industries and the Canadian Labour Congress and their affiliates commenced discussions on the value of the Employee Assistance Program (E .A.P.) philosophy to both management and labour.In the contract signed between Inco Ltd., Manitoba Division and Local 6166, U.S.W .A. in 1981, a commitment was made to establish a joint E.A.P. for the hourly workforce in Thompson, Manitoba. With this background and sequence of events in mind, it is appropriate to explain the methodology and the steps that were taken for the implementation of the hourly program. Development of Hourly ProgramIt was agreed by the company and the union that the committee to develop the program should consist of equal numbers from both sides: three active union members plus an advisor representing the Union and three supervisory personnel plus an advisor representing the Company; in addition, a person familiar with E.A.P.s from the Alcoholism Foundation of Manitoba was to act as a facilitator. The Union appointed a social worker who was working as a counsellor for union members as their advisor , and the company appointed a staff employee who had worked voluntarily in the field of alcohol and drug abuse for many years. The makeup of the committee was extremely important in order to give credibility to the entire process. The makeup of the committee is shown in Table 1.The facilitator selected from the Alcoholism Foundation of Manitoba was well known in the community and highly respected in his profession."

Jan 1, 1989

By V. Polotski

This paper describes a platform for autonomous operations in open pit mining environments. A typical operation consists of: (1) Initial locomotion toward a remote worksite; (2) Pattern navigation within the worksite; (3) Worksite manipulations and (4) Return locomotion to the start location. The platform includes precise localization module based upon the fusion of odometry, inertial and GPS measurements. The guidance module starts from a set of way points specified on a GPSreferenced map and plans and executes the mission. A typical mission includes specified manipulative tasks along the navigation path. During motion execution the on-board system continuously verifies that the path is free of obstacles and that the hardware is not overloaded. Momentary losses of external positioning measurements does not adversely affect the performance, owing to the redundancy in position and heading estimation. A rehearsal phase follows planning and allows the supervisor to examine the kinematic behavior of the platform during motion, thus reducing the need for continuous monitoring during execution and providing protection against potential losses of communication.

May 1, 2003

By J. Smit, F. Parada, R. Parra, E. Balladares, M. P. Merino

"In this study, a two-step process was developed for recovering copper, molybdenum, zinc and iron (hematite). In the first step, grinded slags (-65 mesh) were sulphated with SO3 at 350-500ºC to form iron, copper and zinc sulphates. In the next step, the formed sulphates were decomposed to hematite, copper and zinc sulphates and oxysulphates at 700-750ºC. The generated SO3 was recirculated back to the sulphation step. The generated calcine in the decomposition step is leached with 25 gpl acid at 50ºC to dissolve the copper, zinc and molybdenum for further conventional separation and recovery. The hematite residue, of intense red color, can be used as pigment, in the ceramic industry or as pellet feed. The fine crystalline silica remains in the hematite residue."

Jan 1, 2014

The following guidelines have been recommended by the Diamond Exploration Best Practices Committee established by the Canadian Institute of Mining, Metallurgy and Petroleum. These guidelines are applicable to public companies and their consultants reporting diamond exploration results. In respect of these guidelines, Diamond Exploration Results are results derived from the initial activities undertaken to investigate a diamond bearing prospect or deposit, to generate tonnage, grade and value estimates that cannot be classified as a Mineral Resource or Mineral Reserve. They do not address the earlier stage reporting of geophysical, geochemical or kimberlite indicator mineral results. Public reports of Diamond Exploration Results relating to mineralization not classified as Mineral Resource or Mineral Reserve must address the confidence limits of the result and contain sufficient information to allow a considered and balanced judgement of the significance of the results. The objective of these guidelines is to assist public companies and consultants in making appropriate disclosure of diamond exploration results by reporting in a manner which is: ??Uniform within the diamond exploration industry; ??Consistent with reporting from other industry sectors; ??Comprehensive; ??Unambiguous. The guidelines are not prescriptive. Materiality is the overriding principle that determines the information that should be disclosed. However, where a company or consultant deviates from the guidelines, the disclosure or technical report should state the extent to which the guidelines have not been followed, and the reasons for the deviation. The guidelines do not in any way replace jurisdictional reporting requirements (For example, the requirement for Canadian reporting issuers to comply with Canadian Securities Administrators National Instrument 43-101 by having technical disclosure endorsed by a Qualified Person as defined in that legislation).

May 1, 2003

"Since all gold mills must sooner or later be cleaned up for permanent shutdown it was felt that a record of what was done at one mill might be of some help to those who will have to do the same job in the future,In cleaning up the mill of Delnite Mines Limited, I had an advantage that most mill superintendents will not have in that I started up the mill and was there until it was shut down, It was also known for two years approximately when the shutdown would be and for a year almost the exact time. This, of course, made careful planning possible and enabled me to get advance information that wouldn't have been available had the shutdown come unexpectedly,Early in 1964 calculation of ore reserves and the known number of working places available indicated that the mine would run out of ore sometime in August or September but not later than October, The time of course would vary with the number of competent miners that could be retained until the shutdown. Since the mining method used exclusively on the ore then remaining was cut and fill, it was known that once mining operations ceased it would require at most two days to crush and grind the last of the ore.In March 1 964 I took samples of the concrete floor under the precipitation presses, in the flux room and furnace room of the refinery and from the assays obtained proved that there would be no profit in breaking up the concrete to recover the gold from it, Samples taken from the top half inch of the concrete floors assayed less than 0, 10 oz per ton,"

Jan 1, 1966

By M. E. Stutt, R. H. Rehder

"The mining industry is taking advantage of the increased performance resulting from the use of variable speed A C drives for large motors. This technology provides increased efficiency under the variable speed and torque requirements of such drives as mine hoists, conveyors, and air moving equipment. The technology does introduce voltage spikes on the voltage wave form that stress the insulation system to a greater degree than would occur with a constant voltage source. These voltage spikes must be considered in the design of the insulation system used for these motors.BackgroundHistorically the insulation systems for large AC motors were designed to withstand with reasonable life the voltage stresses of a 60 Hz constant sinusoidal voltage. One of the design tests is a voltage endurance test that requires the application of a 60 Hz voltage from conductor to ground equal to four to five times normal and establishing a time to failure. These higher than normal voltages accelerate the normal aging process by causing extensive partial discharge activity (corona) within the insulation system and the time to failure is a relative indication of insulation life.In addition to the voltage endurance test at 60 Hz, the individual coils are subjected to a surge voltage test to establish the withstand capability of the turn to turn insulation under switching surge conditions. The surge voltage is a fast rise time, 0.2 microsecond to crest value, voltage spike that can be caused by a circuit breaker or contactor closing operation. These voltage spikes can have a crest value of greater than 3.5 times the normal line to ground crest voltage of the normal 60 Hz power supply. The standard withstand test value is thus 3.5 times normal line to ground voltage. Because the voltage surges or spikes occur mainly during start and stop switching conditions, voltage endurance under these conditions has not been a major factor in insulation system design."

Jan 1, 1995

By J. H. Curran

Agenda ? Challenges of developed world mining ? Software aids for creative and practical engineering ? Rocscience software philosophy ? Rocscience suite of geomechanics programs ? Case study ? design of de-stress slot Mining Challenges of the Developed World ? Dwindling reserves ? Great depths ? Strict operating and environmental regulations ? Competition from lower cost operations in developing countries

Apr 1, 2005

By Alain Tshilombo, Vijay Reddy, Chowdary Meenavilli, Kelvin Buban, Cory Kosinski, Sriraj Meenavilli, Siddhartha Tirumalaraju

The use of artificial intelligence (AI) for process optimization is expected to play an increasingly important role in the future of the mining industry. The objective of AI is to develop a data driven soft (virtual) sensor using historical data that can estimate unmeasurable characteristics of the process and provide appropriate recommendations during operation to optimize the process through continuous learning. The application of AI to a hydrometallurgical process was evaluated by Sherritt Technologies in coordination with NTWIST. Historical operating data obtained from the Ambatovy facility’s High Pressure Acid Leach (HPAL) circuit was used to develop models to predict autoclave discharge parameters based on operating conditions and ore mineralogy. The prediction models were developed in such a way to also allow the user to simulate and test different operating conditions. A second set of models (AI model) were developed based on the prediction models, economic data and operating constraints for a given process unit to identify optimal reagent and steam dosages across the HPAL circuit. The development of these models was significantly complex due to the dynamic and interactive nature of the HPAL process. Despite the complexity of the models, the models were able to predict, with accuracy, the relationship between ore composition, leach autoclaves retention time, acid addition and steam addition with metal extractions as well as levels of impurities in the autoclave discharge slurry. The study showed that AI has the potential to improve the overall operation of a facility through providing tools to assist with training, troubleshooting and process optimization. INTRODUCTION The Ambatovy project, located in Madagascar, is one of the world’s largest nickel and cobalt mining and processing operation, with a design capacity of 60.000 tonnes of nickel and 5,600 tonnes of cobalt per year (Collins et al., 2016). Commissioning and start-up of the Ambatovy mine and plant facilities were completed in 2012, with acid first introduced to the ore leach in March 2012. Commercial production (defined as 70% of design capacity) was achieved in January 2014 and the production level required to achieve financial completion (90% of design capacity for 90 days) was achieved in March 2015 (Valle et al., 2016). Figure 1 shows a simplified flowsheet of the hydrometallurgical pressure acid leach (PAL) process employed by Ambatovy.

Jan 1, 2019

By A. Navarra, Norman Toro, T. Marín, Fernando Ayala

The quantitative techniques to evaluate the enhancement of a particular unit operation should consider the corresponding changes to the adjacent unit operations. For example, the expansion of off gas handling capacity should consider the corresponding changes in converter cycle times, matte grade, and other operational parameters, that can provide the optimal system-wide benefit. In general, the upgrading of smelter equipment is risky due to the size of capital investment, as well as any unforeseen impacts on rest of the operations. However, this risk can be mitigated by applying the principles of Front End Loading (FEL) in the formulation of multiphase re-engineering projects. The initial phases of engineering are relatively inexpensive, and determine whether or not to pursue the subsequent phases that are comparatively more expensive. Each phase of engineering depends on increasingly detailed descriptions regarding the critical phenomena that can effect design decisions; the increasing levels of detail may result from numerical simulations, as well as laboratory and plant trials. The quantitative framework should be sufficiently flexible to accommodate these increasing levels of detail, regardless of the particular phenomena, so that it may evolve throughout the project. The current article describes the combined usage of mass balancing, thermochemistry and multiphysics, in the development of discrete event simulation (DES) and finite differences (FD). The incorporation of finite differences into a DES framework depends on adaptive time-stepping, to determine threshold-crossing times, e.g. when the matte temperature surpasses a critical level that necessitates the addition of cold charge. The hybridization of DES and FD is appropriate for multiphase smelter development projects, as it supports semi-continuous material flows, operational policies and scheduling, as well as unexpected events and trends, in increasing levels of detail. This type of framework will support the installation and tuning of modern control systems, including state-of-the art sensors and machine learning algorithms.

Jan 1, 2019