Search Documents

By N. A. Duke, R. L. Carpenter

Abstract - The West Meliadine area is underlain by structurally interleaved panels of mafic and minor ultramafic metavolcanic rocks and metasedimentary rocks that occur along the northern margin of the Neoarchean Rankin Inlet greenstone belt. Three structural and metamorphic domains are recognized: (1) the easterly Wesmeg domain; (2) the central Barracuda-Ridge domain; and (3) the westerly Peter Lake domain. The Wesmeg domain is characterized by a series of southeast-trending, north-dipping, foliation-parallel panels of greenschist facies mafic metavolcanic and metasedimentary rocks. The Barracuda-Ridge domain is comprised of greenschist to amphibolite facies mafic metavolcanic rocks that define an east-northeast-trending structural grain. The Peter Lake domain consists of amphibolite facies mafic metavolcanic rocks and minor metasedimentary rocks intruded by a monzonite pluton. West Meliadine hosts the economically significant Wesmeg gold deposits, as well as other important gold showings across the Barracuda-Ridge and Peter Lake domains. The geological setting of the Wesmeg gold deposits resembles that of a break or fault zone. The Pyke Break is a major geophysical discontinuity (>65-km strike length) and is the first-order structural control on gold mineralization at West Meliadine. It is several kilometers wide and characterized by polyphase deformation and shear zone development accompanied by lode-gold mineralization. In general, gold concentration is related to quartz and iron-carbonate veining, iron sulfides (mainly arsenopyrite and pyrrhotite), and accompanying silicate alteration minerals that overprint favorable chemical and structural traps late in the history of deformation.

Jan 1, 2004

By R. W. Boyle, W. Dyck

"Scientists throughout the world have observed radioactive disequilibrium in the uranium decay series. Radiometric and fluorometric determinations of U in plants from the Goldfields district and in sediments and rocks from the Beaverlodge district exhibit marked radioactive disequilibrium. The eU/U ratio in plants rooted in mineralized ground shifts from greater than unity to less than unity for those rooted in background soils. A similar shift is observed in the transition from rocks to stream sediments and to lake sediments in the Beaverlodge district.Results of a Rn-Ra-U survey of lake bottoms in the Key Lake district show that anomalous hydromorphic U from U mineralization is parallelled by anomalous Rn, even though there is much less Ra in the lake-bottom sediments than one would expect from the amount of U present. IntroductionDisequilibrium in the U decay series has been studied for many years and is observed in almost all surficial environments. Rosholt (1959) measured U, 234Pa, 23O'fh, 226Ra, 222Rn, and 210Pb in a large number of U ores and outlined six types of situations to explain disequilibrium. Davy (1974) outlines the geological significance of radioactive disequilibrium situations with respect to exploration. Levinson and Coetzee (1978) discuss possible mechanisms by which separations of parent and daughter elements are affected and suggest analytical pitfalls that may be encountered in the use of radiometric techniques when disequilibrium has occurred. Generally, it is the oxyphile and easily complexed parent 238U (with its associated isotopes 235 U and 234U) that is leached from rocks and soils at a faster rate than are the daughters, 230Th, 226Ra, 2loPb, and 206Pb. This mobilized U is adsorbed on sediments in streams and lakes, or enters groundwaters, where it is eventually precipitated under reducing conditions, occasionally in oregrade concentrations. This surface leaching and"

Jan 1, 1980

By J. Robison, H. Pieterse, C. C. Smith, M. Luque, S. Chipman

Phase change during pressure let down releases significant amounts of energy that must be controlled to avoid undo wear and tear on equipment. Hydrometallurgical slurries require flow control equipment (valves and tanks) made of expensive materials to withstand the abrasive, and often corrosive nature of the slurry. Presented is a model of the nozzle of a let-down choke which is designed to control the flow pattern that exits the choke (valve) as it enters the receiving tank. This model can be used to design chokes which allow for the dissipation of the energy released during pressure let down by spreading the stream over a significant portion of the slurry pool in the receiving tank to minimize wear on equipment near the nozzle exit and the bottom of the slurry tank. An example uses the model to choose the nozzle expansion (area) ratio to select the outlet slurry velocity and slurry expansion angle.

Jan 1, 2004

By J. Lipp

The lion share of lithium produced globally originates from South American salars. The standard operation for lithium production utilizes an array of evaporation ponds. This process consume vast areas and is either very slow when relying on solar evaporation - roughly 18 months of residence time; or with very high energy consumption since over 90% of initial water volume needs to be evaporated. A new technology, based on solvent extraction was developed. Results indicate a distribution coefficient up to 30, and selectivity greater than 1,000 towards Na extraction. The loaded solvent is stripped using a strong mineral acid, and the product solution is the lithium derivative of that stripping acid. Utilization of this new LiSXTM technology results in reducing the area needed for a commercial plant as well as reduces the residence time. In addition applying different stripping acids can diversify the product line of such facility.

Jan 1, 2014

By A. Sutherland Brown

"The ProblemMany science activities receive substantial funding from governments without much direct economic benefit accruing to state or individuals. In contrast, the search for knowledge has never been an acceptable so le justification of geoscience activity, perhaps because of its utility right from its inception. William Smith's geological activities were embraced because of their usefulness in building canals. Utility has been expected ever since.For decades it has been accepted at senior level s of government, without much understanding of the process, that geological surveys are necessary as a basis of resource evaluation and utilization. Recently, government treasury board s, staffed with economist s, have questioned these near axioms and in many cases the budget s of geological surveys have reflected their stone y-eyed appraisal s. Are government surveys necessary? Can their functions be reduced? Can some or all of their functions be privatized?Government geologists have been muted in trumpeting their successes outside their own ranks. Companies have been reluctant to give specific public feedback on the work of government surveys that have truly aided or guided them toward discovery. Lack of acknowledged linkages between survey work and discovery has dogged survey managers in budget reviews. Impoverished surveys cannot perform adequately so the circle is completed and the doubters' prophecy fulfilled. This is the genera l problem; British Columbia is the archetypical province."

Jan 1, 1986

By Neillm Alastair S.

"This paper looks at what has happened in the past decade in the rare earth industry, particularly for those companies outside China trying to develop alternative projects to the Chinese dominated supply chain. The rare earth industry has gone through a metamorphosis over the past decade. The industry was basically unknown outside China until overnight it became the next hot topic on the financial streets of Canada and Australia. Suddenly various junior miners shifted from uranium and other out-of-favor commodities to rare earths as funds were easy to access from an investment community that did not understand the complexities of the space. The initial funding was done on traditional junior mining metrics of grade and deposit size. This has morphed over time to:1) Lights versus heavies2) Making a concentrate3) The importance of separation4) Off-take agreementsAt the peak of the market frenzy certain flagship operations were built using the “Not Made in China” moniker. Unfortunately certain errors were made during implementation, which are finally coming to the surface and making the rest of the pack wondering what will happen next. A review and update of some of the mistakes made and lessons learned will be discussed.BACKGROUNDAbout ten years ago awareness started to form around the rare earth industry and various groups recognized that because of the closure of Molycorp, Mountain Pass, and the dominance of China, there was a risk of uncertainty of reliable supply. This was not news for those active in the industry like Rhodia (now Solvay), the Japanese, South Koreans and other key consumers but to others it was like a light went on and rare earths became the new “.com” trend for investment banks, investors and some mining companies looking for the next hot topic.In the late 1990’s Molycorp accounted for around 20-25% of the world’s supply of rare earths, mostly lights (La, Ce, Pr and Nd), with small amounts of heavies from other sources. Then environmental issues forced the closure of the operation at Mountain Pass. Within six months China had increased production to plug the gap in supply. Around that time China was developing a strategy to leverage their position in rare earths and implemented a series of regulations to increase the value added component of rare earths inside China."

Jan 1, 2016

By Ralph J. Holmes, David McCallum, Alan Roberts, Rolando Orense, University of Auckland, Tobias Krull, Tom Honeyands, Kenneth Williams

"The safe ocean transport of bulk commodities like iron ore, coal, nickel ore, manganese ore and bauxite by large bulk ships is vitally dependent on the stability of the cargo under the influence of wave induced ship motion. Safety standards are set by such bodies as the International Maritime Organisation (IMO) with recommended tests for the assessment of bulk commodities. Since the 1960s, the bulk cargo code (BC Code) commenced defining methods to determine the Transportable Moisture Limit (TML) for transportation of bulk commodities. By the latter part of the 1960s, three TML test methods were defined, namely the Flow Table, Proctor-Fagerberg and Penetration tests. All three tests were predominantly aimed at determining TML values for mineral concentrates.More recently, bulk commodity producers, Maritime Organisations and Port Authorities worldwide have been investigating whether commodity based TML methods better reflect realistic safe ship transportation than the current concentrate based TML test methods. In these investigations, the relationship between the mineralogical and particulate parameters of specific commodities with respect to cargo stability and moisture retention has provided insights into the development of tailored TML test methods. To this end, an AMIRA International project (P1097) undertaken by CSIRO, TUNRA Bulk Solids, the University of Newcastle and the University of Auckland assisted the IMO Technical Working group to investigate the relationship between iron ore fines characteristics and a new TML test specific for iron ore fines bulk cargoes.A review of the three standard concentrate based TML methods and characterisation studies of iron ore fines, as well as cyclic triaxial testing to determine liquefaction resistance, resulted in the development of a modified Proctor-Fagerberg method for determining the TML of iron ore fines. Of particular importance in determining TML is mineral composition, porosity, particle density and allowing time for moisture equilibration."

Jan 1, 2016

By C. McLachlan, J. R. Donald

"Positioned at the forefront of the seafloor minerals industry, DeepGreen Resources is on track to becoming a leading producer of base and strategic metals obtained from vast high-grade seafloor polymetallic nodule deposits. DeepGreen believes the seafloor minerals industry is an opportunity for developing a more environmentally and societally attractive way to produce cleaner base and strategic metals. Polymetallic nodules contain nickel, manganese, copper, cobalt and other base and strategic metals. Polymetallic nodules represent an exceptional multi-metal-bearing resource, and no current metallurgical operation or flowsheet exists that can recover the primary metallic values while managing the distinct mineralogy. DeepGreen Resources is developing a new process to maximize the business outcomes consistent with the highest environmental standards, including targeting a near zero waste facility. The present paper discusses the history, context and driving forces of polymetallic nodule project development. An overview of DeepGreen?s Nauru Ocean Resources Inc. (NORI) project is presented along with a literature review of polymetallic nodule processing and the on-shore project development scope and plan at DeepGreen Resources is outlined.INTRODUCTION AND CONTEXT Polymetallic Nodules in the Clarion-Clipperton Zone Containing nickel, cobalt, copper and manganese, polymetallic nodules occur in most oceans of the world. The nodules lie on the seafloor sediment. The largest deposit in terms of nodule abundance and metal concentration occurs in the Clarion-Clipperton Zone (CCZ) on vast abyssal plains at a depth of 4,000 to 6,000 metres. The CCZ is located almost entirely in international waters as presented in Figure 1. It has been estimated that the CCZ contains (International Seabed Authority, 2010): •,>21 billion tonnes of nodules; •,>270 million tonnes of nickel; •,>6 billion tonnes of manganese; •,>234 million tonnes of copper; •,>46 million tonnes of cobalt. There are several active hypotheses for the mechanism of formation of the nodules including precipitation, hydrothermal decomposition of basaltic debris, and involvement of microorganisms. Nodules require a nucleus to start forming, which could be a piece of pumice, a shark tooth, old nodule piece, basalt debris or even microfossils like radiolaria and foraminifera. Nodules form concentrically with layers of iron and manganese hydroxides around a core. Although composed mainly of Mn, Fe, silicates and hydroxides, it is the significant content of Ni, Cu, Co, Zn and Rare Earth Elements (REE) that is generating the economic interest in harvesting these deposits. Nodules vary in size from micro-nodules to about 20 cm, the common size being two to eight centimeters. A typical polymetallic nodule and polished cross-section is presented in Figure 2."

Jan 1, 2017

By J. Baumbach, H. Bombach, M. Stelter

"Today technical electro-refining processes for copper exclusively use sulfuric acid, for silver refining nitric acid electrolytes are used. Sulfuric acid is characterized by very good chemical and electrochemical stability, good conductivity and low cost. The disadvantages of sulfuric acid are the precipitation of fine-grained cathodes with smooth surfaces only by using additives like glue, thiourea and chloride. In case of silver the electrolyte is electrochemical unstable and bears the risk of the formation of toxic NOx when pH is too low. A second disadvantage is the form of electrodeposition of silver as dendrites with their removal from the bottom of the Möbius cells.This paper reports the results concerning the application of an alternative electrolyte in copper and silver electro-refining. At first the electrolyte was characterized by the determination of current density potential curves. Electrolysis experiments were performed in laboratory scale using technical anodes for copper and synthetic anodes for silver. During the copper tests the solubility of contaminations from the anodes and the amount and chemical composition of the anode slimes were determined. Moreover the influence of current density, electrolyte temperature and the effect of several additives on the precipitation and chemical purity of the cathodes were investigated. In all experiments cell voltage as well as anodic and cathodic polarization was measured and current efficiency and specific energy consumption were calculated. A comparison with the results with those of tests using conventional sulfuric acid electrolyte shows the advantages and disadvantages of both systems, additionally the technical application chances and limitations for the new electrolyte. This electrolyte enables the precipitation of smooth copper cathodes with low silver and sulfur concentrations even at lower temperatures without any additive. For silver refining the electrodeposition of compact silver sheets is possible, that can be stripped comparable to those in copper electro-refining."

Jan 1, 2016

By A. Boeing

Rock-breaker automation and remote operation improves the safety and efficiency of mining operations. This article presents an overview of the Rocklogic rock-breaker automation system architecture that provides collision avoidance, automated parking, and remote operation functionality. The system consists of a distributed computer control system that interfaces with sensors attached to the rock-breaker, the rock-breaker hydraulics, and the site infrastructure. We present results of an automated Transmin rockbreaker installed in a production environment at an underground Australian mine site. The system has been in production use for over 900 days during which there have been no reported collisions, and 100% adoption of the remote operation technology. As a result, Rocklogic has significantly improved the safety of rock-breaking operations and reduced the rock-breaking cycle time, thereby improving the sites overall throughput.

Aug 1, 2013

By A. G. Scobie

A spectrographic method for the determination of small amounts of gold and the platinum metals in ores has been developed. By means of this method, an assay of 0.001 ounce per ton on one assay ton samples is possible, and by seecrrographic adjustments the sensitivity may be increased to 0.0001 ounce per ton. All the prec10us metals may be determined from one spectrographic arcing with an accuracy of about 5 per cent average deviation from absolute values, and the complete analysis of an ore or similar product may be reported five or six hours after receipt of sample.

Jan 1, 1945

By J. Keith Haddock

"Introduction The Boundary Dam Mine is located 5 km south of the City of Estevan, Saskatchewan and is operated by Manitoba and Saskatchewan Coal Company Ltd., one of the Luscar companies. The entire production of 1.7 million tonnes per year is delivered to the Boundary Dam Generating Station of Saskatchewan Power Corporation. Geology There are basically two seams mined on the property, the main Estevan seam ranging in thickness from 3.0 m to 4.5 m with partings and the upper Roche Percee seam (roughly 15 m to 23 m above the Estevan) which ranges from 0.6 m to 2.0 m in thickness. Most of the reserves are concentrated in the Estevan seam, the Roche Percee only being mined whenever its thickness makes it economic to recover. The coal measures belong to the Ravenscrag Formation of Tertiary (Paleocene) Age. This formation is widespread in North Dakota and Montana and contains the lignite fields of North Dakota and subbituminous coals of Montana. The formation is gently tilted to the southeast at Boundary (0.5 degrees) and consists of weak sandstones, siltstones and silty mudstones. Reserves and Coal Quality The present minesite encompasses a coal reserve of approximately 50 million tonnes calculated to a maximum stripping depth of 37 metres or 20:1 mining ratio. The reserves form only a part of the total reserves in the Estevan area which are owned by the Saskatchewan Power Corporation. The coal being mined is classed as Lignite ""A"" and has the following specifications:"

Jan 1, 1985

By P. C. Santos-Munguía, F. Nava-Alonso, O. Alonso-González

"The gold recovery of a Mexican cyanidation plant, in Sonora, has been decreasing due to the increasing presence of gold tellurides. This work presents the results of different processes aimed to recover the remaining gold from the cyanidation tailings of the operation. The cyanidation in the mine is performed at 0.1 g/L NaCN and pH = 10.3, adjusted with lime. The treatments studied in the laboratory with these tailings were: cyanidation at higher cyanide concentration than that used in the plant, cyanidation with oxygen injection, cyanidation with oxygen and lead nitrate addition, and thiourea leaching. The results obtained with each of these treatments are presented and discussed with the final objective of proposing a method to recover the gold associated with tellurium.INTRODUCTION It has been demonstrated that gold telluride is refractory to the conventional cyanidation process and, for this reason, some alternative methods to recover precious metals from tellurides have been proposed. (Zhang et al., 2010). These include cyanidation with modified conditions or the use of non-cyanide leaching agents. This work presents the gold leaching results of tests performed with a sample of cyanidation tailings obtained from a Mexican deposit containing telluride species. The mine exploits a mesothermal deposit with a molar Te/Au ratio of 1, containing also lead, molybdenum, bismuth and tungsten. Gold is recovered from the ore by standard cyanidation, however, lately the gold recovery has decreased, likely due to the tellurium content of the ore. The sample used in this work was the cyanidation tailings of this deposit. It was treated in the plant by cyanide heap leaching (0.1 g/L NaCN, pH = 10.3 adjusted with lime). Some gold remained after the cyanidation and it was thought that this gold was associated with tellurium. The objective of this work was the recovery of the remaining gold from the tailings by an alternative process."

Jan 1, 2017

By P. A. Tichauer

Arbitration is a flexible method for dispute resolution that gives control to the disputing parties while still maintaining a clear and well-structured decision making process. It responds to the desires of the parties for a resolution that is fair, binding and enforceable and is guided more by pragmatism, efficiency, effectiveness and equality than by a need to comply with the legal procedures and practices of any single country or jurisdiction. Arbitration is particularly well suited for the resolution of disputes pertaining to international commercial agreements which are often present in the metallurgical sector. This paper provides a simplified outline of the features and advantages of arbitration as well as commentary regarding certain prerequisites in order for arbitration to be binding and enforceable.

Jan 1, 2015

Pilot plants for pressure hydrometallurgy represent special design and project execution challenges unique to the industry and to the pilot- and demonstration-scale. Pilot plant projects have different objectives and shorter timescales than commercial plant projects. Design considerations and strategies, and project execution methods that meet the special needs of pilot plant projects, are discussed. Specific guidance is given for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical process equipment, and for the selection of materials of construction for pilot-scale equipment. The balance between the need for process similarity with future commercial operations and the realities of pilot-scale equipment is also discussed.

Jan 1, 2004

By A. Scheltema Beduin, H. Oterdoom, A. Haaks, C. Kempe, A. Liedtke

The bath level measurement is applied in many furnaces to keep control of the level of slag and metal or matte inside. The BLM is used mainly in bath processes, and has not seen much evolution in its basic functionality. For a closed DC FeCr furnace, special demands based on the furnace design and extreme process conditions were considered for the design of a bath level measurement in order to collect valuable information about the furnace operation. This paper will describe these demands and the solutions for them, followed by some of the uses for the BLM in a closed FeCr furnace. Some of the future developments on the BLM conclude this presentation.

Jan 1, 2015

This paper describes results of an investigation of fracture during tube expansion of 5052 and 5754 aluminum seam-welded tubes to optimize the forming of aluminum tubes during hydroforming. The tubes were produced in laboratory by press forming of tubular blanks and pilot-scale high frequency induction welding. The effect of property mismatch between the weld and base metal has been investigated. The material work-hardening was obtained by roll forming of sheet blanks in the 0-temper and H32 temper condition. The results showed that a significant work-hardening can be present in aluminum tube without causing weld fracture during tube expansion. The work-hardening increases the yield-strength mismatch between base metal and weld. Annealing reduces the hardness of base metal leading to more uniform deformation during tube expansion. As a result the occurrence of weld fracture is reduced. The study showed significant deformation of the welds during tube expansion. Weld thinning can be as large as parent-material thinning before fracture. To avoid fracture at the weld joint, good formability and high yield strength of the weld is needed. FEM simulation showed that minimizing the width of the weld joint can reduce thinning of the weld.

Jan 1, 2004

By Donald S. Macdonald

"I AM thankful for this opportunity to address the Toronto Branch of The Canadian Institute of Mining and Metallurgy. The Members of your Institute can have a great influence on the direction in which the mineral policies of Canada will evolve, and to assure that optimum benefits from our country's vast mineral resources will accrue to the nation as a whole and to all its citizens. Today, I want to: (1) offer an outlook on the mineral industry for 1973; (2) talk briefly about the role of minerals in the total economy; and (3) outline some of our thinking with respect to a national minerals policy for Canada."

Jan 1, 1973

By B. Wasmund, M. Parravani, M. Jastrzebski, Z. Coull

"One of the main drivers of overall profitability of pyrometallurgical vessels is refractory lining campaign life. Increased economic pressure to improve vessel life requires innovative solutions to the problem of refractory cooling. Hatch has recently developed a high-intensity, waterless cooling system that bridges the performance gap between external shell cooling and internal water-cooled copper elements. External shell cooling has a limited effectiveness in protecting the refractory lining, because it is thermally insulated from the hotface of the lining by its thickness. This situation does not improve until the lining itself has become worn near the end of the campaign. The patented technology developed by Hatch overcomes this problem by positioning high-velocity air-cooling channels within the lining, closer to the hotface where the cooling benefits can be realized throughout the entire duration of the campaign. The current paper presents the development and application of Internal Air Cooling technology as well as results from the pilot campaign in an operating commercial vessel. Various adaptations for this novel, cost-effective and inherently safe system are also discussed."

Jan 1, 2015

By John Ratti

Building on Canadian Capabilities for Space Resource Missions: Space resource science and technology mission building blocks Canadian historical perspective Status and future pursuits It takes Canadian Teamwork to succeed in space exploration! Space resource science and technology building blocks: Orbiting / Delivery Elements Spacecraft Sensors Landed elements Roving / Mobility, Autonomy Sample acquisition and handling Sensors, GN&C Science Operations Partnerships: Government ? Industry Between Industry With Academia and Scientists

May 1, 2013