Search Documents

By Todd Kennedy, Kurt Tischler

"This paper presents the field experience of Siemens with regard to Gearless Drives in the mining industry … We consider the elapsed production hours of Siemens Gearless Drives to be extensive enough to provide a reliable estimation of availability calculated on the basis of data representing repair time, downtime, and operating time. The users of Siemens Gearless Drives confirm an availability of more than 98% after exclusion of some major issues. The paper addresses all of these major issues of Siemens Gearless Drives, describes successfully applied corrective measures, explains the influences on the design of the drives, and lists the downtimes associated with each of these issues. INTRODUCTIONThe first Siemens Gearless Drive in mining began operation in 1980 and was installed on an iron ore grinding mill. As of September 2011, 40 Siemens Gearless Drives will have accumulated 136,000 machine days of operating time. According to pure rules of statistical analysis, this accumulated operating time may be too low to be used for a sample of field data to provide precise statistical values of availability, however we consider it large enough to provide indicative values of worthwhile consideration. This paper deduces the availability statistics of Siemens Gearless Drives in the mining industry from information received from end users and factors in all major issues that Siemens has experienced with our Gearless Mill drives. This paper does not consider Gearless Drives in other industries such as the cement industry. The cement plants, especially in the northern hemisphere, interrupt production for several months in the winter. This lengthy downtime is used to maintain the complete plant including the mills, their motors and their drives. The mining industry has more stringent and higher production requirements. In the mining industry, production must run 24 hours per day, 365 days a year."

Jan 1, 2012

By Peter J. Franklin

"Short-term mine planning of open pits is an activity that has historically been carried out by hand. Typically, the use of computers has played little part in this type of mine planning. This paper describes the objectives and the procedures involved in short-term mine planning, comments on the type of computer systems available, and describes in detail a computer-aided short-term planning and scheduling system known as STEPS.IntroductionThe mine planning department of any o pen-pit mining operation performs a wide variety of different tasks. However, their primary concern is the preparation of detailed long-and short-term mine plans. These mine plan s will define the long-term operating strategies and definitive everyday working plan s for the ongoing development of the open pit.In this day and age, when operating costs have spiralled upwards due to inflation , and product revenues have decreased due to depressed economies and poor markets, it is vitally important for all aspects of the mining operation, including mine planning, to be efficient and cost effective.There are numerous options available for planning engineers when generating a mine plan. A cost effective mine plan must investigate all these options and select the optimum. When using manual planning techniques, it is often impossible to evaluate all the available options. To do this, and to produce an optimum mine plan, a computer is required.This paper discusses mine planning, with emphasis toward the short-term plan and comments on how the processes may be computerized. It also describes in detail, a computer software system called STEPS, which has been designed as an interactive graphics, computer-aided short -term mine planning and scheduling tool."

Jan 1, 1985

By M. Somppi, Z. Yamak

"Gold producers invest significant effort in mining, processing, and creating an intermediate gold doré product. Nonetheless, equal effort should be extended to the final handling and processing of the doré bar, and managing the high-purity gold produced at the fine-gold toll refiner. This detailed attention to bullion handling and refining provides rigor and confidence that the mine site is achieving, through fair and controlled methodology, the most appropriate value for the final product. With the above in mind, the following study explores the importance of preparing a set of site best-practices for bullion handling and specifically, detailing the peculiarities of sampling methodologies and the impact on assays.INTRODUCTION Gold and silver handling practices are common place at mine sites and refineries. The practices include but are not limited to smelting, ingot casting, weighing practices, and secure transportation. Proper handling and processing of the bullion material ensures that the mine site is achieving the true value of the final product. Various handling aspects can critically impact the perceived value of the bullion. A few of these particulars include weight tracking, scale recertification and calibration, refining and melting practices, melt temperature measurement, sampling, pouring, bar cleaning, furnace technology and crucible selection, and assaying. Nevertheless, this report discusses and focuses on the importance of proper sampling and molten-metal temperature measurement and their potential impact on the final doré bar value. Refining or re-melting operations achieve a proper measure of the precious metal content of its bullion when the sample accurately represents the whole bar. At first this task appears seemly straightforward, however, taking a representative sample can be challenging and is also one of the most important tasks for valuing gold during the settlement stage at the precious metal refinery. Various bullion sampling methodologies exist; including: dip sampling, granulation, drilling, cutting, and vacuum pin sampling. The Royal Canadian Mint (2009) indicated in their technical review of refinery operations that pin sampling is one of the best methods for cases where representative sampling and accuracy are required, e.g. to determine the payable metal content. Pin sampling consists of inserting a sealed glass vacuum tube (Figure 1) into the molten metal; when the molten metal contacts a purposely-designed weak portion of the glass, the seal breaks and the metal is suctioned into the hollow centre (Figure 2)."

Jan 1, 2018

By Y. -B. Kang

New databases are being developed to provide the capability to evaluate the suitability of present and potential new Mg alloys for automotive applications through cost-effective calculations. An extensive and complete thermodynamic database is being prepared for Mg alloys formed from among 25 present and potential alloying elements. The database is being developed by critical evaluation, modeling and optimization of available phase equilibrium and thermodynamic data. It contains model parameters giving the thermodynamic properties as functions of temperature and composition. Using the FactSage thermodynamic software, users can access the database to calculate the amounts and compositions of all phases at equilibrium at any temperature and composition or to calculate any phase diagram section in multicomponent alloys, to follow the course of equilibrium or non-equilibrium cooling, to calculate corresponding heat effects, etc. A database of densities and lattice parameters of Mg alloys and intermetallics (as functions of temperature and composition) is also being developed in order to permit the calculation of volume changes during cooling and phase transformations, c/a ratios of the hcp phase, etc.

Jan 1, 2006

By W. H. Hodgson, A. R. Preston

"Improved rail production techniques provide new options for the rail user. Steelmaking improvements offer tighter composition control, lower oxide and sulphide counts, greater control of segregates and freedom from hydrogen problem s. New ultrasonic, laser and eddy current equipment gives printout information on surf ace flatness, straightness and internal condition. These have come along at a time when dramatic changes have occurred on the rail heat treatment scene. Rails can now be deep hardened on or offline in ways which should eventually result in a complete rewrite of the world's specifications. Rails of simple composition can be produced in the hardness range 2801400 BHN as required. The rail user can choose the hardness within this range according to requirement without the necessity for any step changes in the process routes.It is suggested that this is the pattern f or the next decade.IntroductionRails have been the subject of very slow improvement over many years but developments gathered momentum in the early seventies. Recent improvements in quality and properties have provided dramatic increases in rail life under the more severe service situations. Rail profile grinding, lubrication and other track improvements have greatly added to expectations of even longer life. All of this, coupled to even newer mill heat treatment developments, tilt both technical and economic advantages away from tradition to the point where specifications will need to be rewritten so that railroads can take full advantage of these new products."

Jan 1, 1988

By T. Gerritsen, R. MacRosty, R. Pula

For several years Hatch has been installing fibre optic temperature sensors on the copper cooling elements of smelting furnaces to improve monitoring capabilities in critical locations. The metal/matte tapblock is a key area to monitor in the furnace as it undergoes severe wear from the molten material repeatedly drained through it. The high wear rate around the tapblock means downtime is necessary to perform refractory repairs. A good understanding of the tapblock condition allows the operation to maximize safety and production; consequently the metal/matte tapblocks have been the focus of this study. Fibre optic technology allows the installation of numerous sensors in locations that are very sensitive to refractory thickness, thereby providing information previously unavailable with traditional measurements. The transient nature of the thermal response to tapping and the three-dimensional geometry of the tapblock confound the interpretation of refractory thickness from temperature measurements. This paper focuses on the analysis of both plant data and thermal modelling simulations and details the progress made in relating the temperature measurements to the refractory thickness in front of the copper tapblock.

Jan 1, 2014

By George R. Pratt

Although the title of this paper focuses attention to the Winnipeg coal market the following remarks should be considered applicable not only to conditions in Winnipeg but to the whole western coal industry. Technical descriptions of coal and coal-burning have been omitted. These details are already covered in other numerous publications. In discussing a market the first consideration must be the product which is required to be sold. The class, quality and price at the point of origin must be taken into account and therefore this feature will be discussed before proceeding to outline conditions in the Winnipeg local market. The writer thinks of coal as a manufactured article, not, as it is generally considered, a fuel to be dug from the ground and dumped into the consumer's bin. The work of manufacturing must be considered in detail:- 1. Consider first the coal as it is in the ground: (a) What is its fuel value? (b) Where is its market? © With what will it be in competition? 2. Consider secondly: (a) What it will cost to mine the coal. (b) What has to be done to prepare the coal for market after it is mined. This must be considered in conjunction with the answer to question 1 ©. 3. Thirdly, consider the method of business to be adopted by the producer:- (a) Is it proposed to build a market on price? Or (b) On quality?

Jan 1, 1925

By W. H. De Blois

Introduction In the contact process for ?the manufacture of sulphuric acid, sulphur dioxide gas - produced by the burning of sulphur or of sulphur-bearing ores, or as a by-product in the treatment of sulphide ores - is made to combine with the oxygen of the air to form sulphur trioxide, which then only requires the addition of water to form sulphuric acid. The substance, as for example platinum, causing this combination is usually referred to as a catalyst, a convenient term, in the definition and explanation of which many pages have been written. Catalysis is now a comparatively common means of effecting chemical combination, but if the question were raised here tonight as to what actually goes on when this apparently innocent third party unites the parties of the first and second . part, without itself being altered in any way, I am afraid even our most learned members would have to confess their inability to entirely explain the phenomenon; for although the subject is under investigation, there is still much to learn. The contact process, however, is one of the outstanding achievements in chemical engineering. ? From the standpoint of the difficulties involved and the time absorbed in their solution, it probably stands alone in the field of technical chemistry. In fact, the manufacture of sulphuric acid has, from the earliest days, been surrounded with problems which have interested the ablest chemists. The Chamber System Although this paper has particularly to deal with the contact process, it may not be amiss to refer briefly to the chamber system, which was, and still is, a most important factor in the sulphuric acid industry.

Jan 1, 1927

By L. M. Dwarkin

Strip mining in Western Canada, though of considerable importance, is a fairly recent development for many of the operators in the district. Adding to the difficulty of unfamiliarity is the fact that a great deal of the stripping is done on pitching seams, for which the engineering and economic principles of setting the most advantageous strip ratio are not readily apparent. The novelty of the operation combined with the complexity of the principles involved can easily lead to misconceptions as to the determination of the economic ratio. Definition of Strip Ration There are two commonly accepted meanings of the term strip ratio: (1) The ratio of feet of overburden to be stripped per foot of coal recoverable. (2) The ratio of cubic yards of overburden per cubic yard or ton of coal. The first definition is inapplicable to pitching seams so, throughout this paper, strip ratio will be taken as the ratio of cubic yards of overburden to be removed per cubic yard of coal recoverable. Economic Ratio In the case of flat seams, the strip ratio is fixed by existing natural conditions, and the magnitude of this ratio determines whether stripping is economically feasible. With pitching seams, however, the strip ratio is a variable. On the outcrop, there is usually some coal which can be obtained with little or no stripping. As the work is carried down the pitch of the coal seam, the proportion of overburden continually increases until a point is reached where it is no longer economical to continue the operation. The question immediately arises as to the location of this point, and this resolves into the problem of determining the most favourable strip ratio, or, to use the accepted term, the economic ratio.

Jan 1, 1949

By P. R. Brito-Parada, A. Norori-McCormac

Positron emission particle tracking (PEPT) has become an important tool for flotation research, as it is able to resolve directly the behaviour of particles in laboratory scale flotation vessels. The first applications of PEPT to flotation showed only the motion of an individual particle in the pulp and the froth, but nonetheless allowed interpretations of behaviour not previously possible. Since then, PEPT measurement and data analysis techniques have improved significantly and now ensure a high level of confidence in the particle behaviour obtained. In particular, statistical analysis of long-duration experiments allows time-averaged data to be collated, ensuring spatial accuracy and allowing rigorous comparison of different conditions. It will be shown that these PEPT techniques can be used to compare directly the effect of operating conditions and particle properties in a laboratory flotation system. Particle tracks will be illustrated, as well as analyses of particle speeds, average flow streamlines and occupancy that show marked differences in behaviour near the interface and impeller.

Jan 1, 2015

By R. A. Parra, Fuentes, C. Godoy, L. E. Arias, C. A. Toro, M. Marin, E. Balladares, V. Parra, G. Reyes, S. N. Torres, D. Sbarbaro

In this paper, we report on the detection of spectral molecular emission of iron oxide (FeO) and copper oxide (CuxO) emitted by reactions occurring in a laboratory scale flash smelting process of pyrite (FeS2) as well as copper concentrate. The novelty of the technique is that, the molecular spectral emission sensing is achieved by using a low spectral resolution and low sensitive radiometer, enhanced with signal processing and matrix factorization techniques. The method was validated using a highly sensitive spectrometer, with a high spectral resolution; achieving a similar FeO spectral pattern as the one obtained after signal processing techniques over low resolution spectral signals. INTRODUCTION Visible-near infrared (VIS-NIR) spectroscopy is an optical contactless sensing technique commonly used to capture information about the emitted, absorbed, transmitted or scattered radiation in a physical or chemical process, with the presence or absence of an excitation light source such as a laser or a broad spectral band source. These techniques coupled with signal processing and machine learning algorithms, sometimes referred as chemometrics (Pisapia et al., 2018), can be found in processes such as: pharmaceutical (Kandpal et al., 2016); food (Coelho et al., 2016); combustion (Ballester & García-Armingol, 2010); siderurgy (Strakowski et al., 2014) industry, among others. In the extractive copper industry there are several technological developments using optical sensing techniques aimed to retrieve information about copper ore and concentrate mineralogical composition such as X-Ray Fluorescence, Qemscan® (Quantitative Evaluation of Minerals by Scanning Electron Microscopy) and X Ray Diffraction (XRD) analysis, however, because of the manual procedures to analyze the samples with these laboratory instrumentation, only discrete information during a daily based operation can be retrieved, making impossible for the operators to take decisions over the involved processes in real time. The aim of our research work presented here is to contribute with sensing and data analysis procedures based on VIS-NIR spectroscopy for the flash smelting process characterization, particularly in this paper, with the detection of FeO and CuxO molecular emissions in a laboratory scale setup.

Jan 1, 2019

By Sarah R. Hindle

Carbon capture and storage has jumped to the forefront of climate change mitigation efforts for its capacity to sequester large amounts of carbon. Mineral carbonation is one prominent option, mimicking and accelerating the natural weathering process of certain silicate minerals. This has the ability to produce stable carbonate minerals that can store carbon on geologic time scales with little to no risk of leakage. Commercialization of this process is ideally suited for integration into the proposed mining operations at the Turnagain Nickel site in Northern BC. This is due to the abundant supply of suitable ultramafic feedstock material, as well as the economic benefit of sharing costs while reducing net emissions and bringing value to otherwise valueless and costly waste rock. While studies have shown this process to be technologically viable on a laboratory scale, assessing the economic and financial viability of such a process on an industrial scale is necessary. An evaluation of the financial feasibility of integrating mineral carbonation into the mining cycle at Turnagain under a proposed cap-and-trade system is presented.

May 1, 2010

By Cesar Carrasco

Mine reconciliation is the art and science of comparing predictions and real-world outcomes with the intent of revealing the true quality of performance of models, planning, mining, and mineral processing. When mine reconciliation is conducted in a systematic, transparent and sustainable way it can play a central role in the governance of Mineral Resource and Mineral Reserve (MRMR) estimation and reporting. The core processes of modelling, planning, mining, and processing need to be transparent to be able to demonstrate that MRMR are reliable predictors of mine performance and value. Transparency is also necessary for mine technical staff to generate meaningful analyses, conclusions, and business improvement actions that demonstrably maximise value for all stakeholders. Most mines have some form of mine reconciliation practice, however because there is no agreed industry standard, and because mine reconciliation is difficult for a variety of reasons, it is often unsustained and/or ineffective at delivering the required transparency of performance. To deliver true governance of MRMR and business value, mine reconciliation must be sustainable. There are two categories of issues that combine to make mine reconciliation extremely difficult to sustain, these are technical, and people related. Technical issues include defining standard terms, accurately tracking material flows, data availability/adequacy/quality, calculation of key performance indicators and tolerance limits, analysis, and interpretation of results, understanding limitations of modelling techniques, and defining appropriate actions that can deliver value. These technical challenges are non-trivial, however compounding these are a range of people issues that include personal agendas, scepticism, lack of knowledge and experience, poor teamwork, absent leadership, toxic workplace culture, staff turnover, ineffective communication, siloed organisational structure, and lack of deliberate change management. All these problems can be solved with clarity of purpose, definition of the process of mine reconciliation, discipline in following the process, appropriate resourcing, and commitment to success across the entire organisation. Outlined in this paper is a management system that delivers sustainable mine reconciliation by addressing both the technical and people issues described above. This approach can deliver significant value for a mine and adds a robust, defensible governance over MRMR estimation and reporting.

Oct 1, 2024

By Daniel Cluff

Frozen backfill for mining operations in permafrost must be delivered in such a state so as not to thermally impose on the host rock surrounding the filled stope. The placement process, the material strength demand, and the freezing time delay are the parameters that control the applicability of the method. A two-year research program was carried out in the field and using a laboratory-scale apparatus, designed to simulate a pour of frozen backfill, to study the mixing, thermal properties and segregation. The frozen rock and tailings must be at a below zero temperature and get fully wetted so the surfaces cause adherence of the particles to one another and enhance the solidification of the poured backfill. The results provided a recipe and a process for mix design for open stoping operations in cold regions. The testing evaluated the sensitivity of the test parameters that included the amount of water added in the mix, the temperare of water, the rockfill/tailings ratio, and the temperature of solid constituents.The paper presents the result of this environmentally friendly, innovative technology. The distribution of the materials and the mixing process are instrumental in achieving the properties required for open stoping applications.

Oct 1, 2010

By C. M. Campbell

THE dire effects of rapidly vanishing natural resources, widespread unemployment, and increased debt and taxation in recent years have challenged Canadians to produce a practical solution to these national economic problems. In more recent months, wars and rumours of war have indicated, among other things, the need for better control of our mineral wealth. The erection of a smelter on the lower mainland coast of British Columbia, treating all Western ores, and such ores as it will be found advisable to import, will make an important contribution toward a solution of these problems. It is believed that the ores tributary justify a smelter of major proportions. A stock-taking to confirm this can be made with reason-able accuracy in a short time, and this should be undertaken without delay. Enough general information is, however, available .in this paper to justify the technicians of the Department of Mines at Ottawa and of interested smelting companies making a preliminary study of the matter. THE DEFENCE ARGUMENT As a factor in rearmament, metals play a vital part. That rearmament is to continue on an increasing scale is indicated in Premier Chamberlain's address of October 3rd last, when he said: ?'For a long period now we have been engaged in this country in a great programme of rearmament which is daily increasing in pace and volume. let no one think because we have signed 'this agreement between the four powers at Munich we can afford to relax our efforts or call a halt in our armaments at this moment'. As matters stand, the facilities in British Columbia are entirely out of line with the strategic importance of this Province as the Western Front of Canada and the Empire. All our copper ores, and an appreciable part of our lead and zinc ores, are sent for treatment to Japan, United States, and Europe, while we import our iron and alloys. A treatment plant on this Coast would not only give us control of war metals and chemicals but it would provide an increased industrial and research population, badly needed in this area and of the greatest value in the case of war. This is where the mining industry can do its bit.

Jan 1, 1939

By D. Groenveld, M. Rozou

"Recent trends move towards automation, smart sensors, internet of things, powerful DCS, and more data. Are those trends already utilized in a real time production environment? Today operators still have to monitor several complex processes at the same time and predict their behavior based on an overwhelming amount of data available.The fact of the operator being overloaded and humans being unable to process multivariable problems shows the need of a tool merging essential data and providing consistent, sound decisions for long-term profitability.This paper shows a successful execution of ABB’s process improvement services in Aitik (Boliden SA), a copper mine located in Sweden. Soft sensors, fuzzy rule blocks and model predictive control were seamlessly integrated in the control system of the grinding area, resulting in proper control of mill loads and particle size without violation of any constraints.INTRODUCTIONDepending on the ore characteristics and the targeted plant capacity, the design of the grinding circuit may vary significantly. Typically, the circuit consists of several mills (rod, ball, SAG, AG) in series and/or parallel with a number of classifiers and sumps at appropriate locations. The goal of the grinding section is to reduce the ore particle size to a level that enables efficient separation between gangue and precious metals in the subsiding processing step. The trade-off between quality and quantity has to be made. It is also crucial to execute this process step at the lowest possible energy and grinding media consumption.An optimal grinding process controller must manage to maintain a given fresh feed level while keeping the product size within a given range without violating any constraints such as power, torque or load limits. To accomplish the aforementioned, it is necessary to manipulate the ore feed rate, water feed rate and the mill speed. The most significant disturbances adding another degree of complexity to this control problem are ore hardness and the amount of circulating load."

Jan 1, 2016

By W. Díaz, R. A. Parra, L. E. Arias, C. A. Toro, M. Marin, E. Balladares, V. Parra, G. Reyes, S. N. Torres, D. Sbarbaro

This work presents visible-near infrared (VIS-NIR) spectroscopy measurements, and signal analytical techniques to characterize minerals and relevant pyrometallurgical process variables for the copper extractive industry. Data signal processing techniques such as baseline correction and numerical analysis are used to estimate the continuous and discontinuous spectral components. Such spectral components are used to estimate the process temperature, and patterns such as the integrated radiation. Also, metal combustion emissivity calculation are depicted. Our findings suggest that VIS-NIR spectroscopy may be a suitable technique to assess the process condition state, appearing as an interesting sensing alternative. INTRODUCTION Although the flash smelting process is one key stage in the copper extractive industry, representing about 40% of copper matte production worldwide (Cantallopts, 2017), few attention is dedicated to develop sensing solutions to assess process variables, such as mineralogical composition and temperature, in the feeding and bleeding stages, compared to the steel industry (Strakowski, et al., 2014). In this process and other industries, e.g. the thermoelectric power generation one, combustion and particularly the generated flame are the production chain’s heart. Since the flame is a highly radiative emitting process where chemical and physical transformations take place, many works had been dedicated to characterize the combustion state by sensing its radiation using optical and photonic technologies (Ballester & García-Armingol, 2010). In this context, this work aims to contribute with visible-near infrared (VIS-NIR) spectroscopy and pyrometry techniques to retrieve relevant information from a laboratory scale flash smelting process. On the other hand, since photonic instrumentation allow us to perform contactless measurements of emitted, absorbed, transmitted or scattered radiation, it appears as a suitable technique for sensing process properties in harsh environments, e.g. high temperature processes. One of these techniques is the Visible- Near Infrared (VIS-NIR) spectroscopy, which provides information about the spectral radiation intensity distribution, in this work, the emitted flame’s radiation. It is well known in combustion research that the spectral emission from a flame is composed by a black body continuous radiation background, molecular emissions, elemental emissions and additive noise features (Arias et al., 2011). To make sense of such information signal processing techniques are needed, here we propose to analyse the continuous and discontinuous spectral components separately.

Jan 1, 2019

By Robert B. Parsons

"No Canadian or his family is likely to escape the effects of proposals for pension reform tabled on October 9, 1986 by Finance Minster Michael Wilson. New tax rules are proposed for Registered Retirement Savings Plans (RRSPs), company pensions, and other forms of retirement plans. Draft legislation is expected to be released in the first half of 1987.IntroductionOver two years ago on February, 15, 1984, Mark Lalonde, then Finance Minister, tabled two White Papers. The first, Action Plan for Pension Reform, proposed improvements to the public pension system and increases in the minimum pension benefits standards to be mandated by the federal government. Since then changes have been made to the Old Age Security, Guaranteed Income Supplement and Canada Pension Plan programs. Also, benefits provided under pension plans subject to the federal Pension Benefits Standards Act have been improved significantly.The companion paper, Building Better Pensions f or Canadians, proposed to standardize and, in many cases, improve retirement savings through private plans by revising the tax rule s. The tax proposals in the Notice of Ways and Means released by Finance Minister Wilson on October 9. 1986 implement, with modifications, the tax treatment of retirement savings originally proposed in the May 1985 budget in response to that second paper."

Jan 1, 1987

By C. E. McCoy

This paper will discuss briefly loader shovel requirements and then present a detailed survey of electrical drive systems to meet these requirements. The survey in general will deal with the various electrical provisions for shovel drives, along with the advantages and disadvantages, and in particular will discuss the MG set and static D. C. drive systems. Also included will be some insight into the requirements for optimum electrical power at the shovels.

Jan 1, 1979

By Carol Odell

This paper was prepared as a brief for Prospectors and Developers Association of Canada (PDAC) to guide input at a series of round tables carried out by the Federal Government in response to the 38th Standing Committee on Foreign Affairs and International Trade (SCFAIT) report, on ?Mining in Developing Countries and Corporate Social Responsibility?. This document mandate is to provide background information, analysis and recommendations on the practice of Canadian exploration and mining companies abroad. This research was based on 11 case studies of Canadian companies which have experienced conflicts or controversies overseas. All case studies were assembled through an extensive literature review of publicly available documentation and communications with representatives of the mining companies to assist in deepening the insights into the drivers of the conflicts and the needs of Canadian companies in similar situations. The case studies include both exploration and mining operations. Our analysis begins with the identification of general and case specific drivers of conflict/controversy in each case study. Company names are kept confidential and only anonymous results are presented. We make ample use of simple flow charts and schematic diagrams to explain how contextual drivers and aggravators and company drivers and mitigators play varied and interrelated roles in conflicts. The diagrams also illustrate the cumulative analysis of drivers including the linkages among drivers/aggravators/mitigators across different domains (social, governance, NGO/media and company). Finally, we discuss needs of companies and propose recommendations for addressing social responsibility and human rights concerns.

May 1, 2007