Search Documents

By James A. Deeks

"Motor failures and equipment bearing failures are responsible for reduced productivity.With the introduction of computers and data acquisition systems, users are now able to monitor, report and trend deteriorating conditions and take corrective action before a critical shutdown occurs.This paper discusses the monitoring and trend analysis of' motors, and motor and equipment bearings. With today's digital electronics technology users are now able to monitor their equipment, detect deteriorating or abnormal conditions quickly, alarm the condition locally and or remotely, and decide if immediate corrective action is necessary or if it can be delayed until the end of a work Shift. All of this can be done long before any damage is done to the equipment.Monitoring Trend AnalysisIt is no longer necessary to compromise in selecting products, since state-of-the-art designs allow the adjustment in such small increments that the users are able to detect minute changes in a system's performance.Monitoring and trending of motors and equipment bearings is now available in economical packages which can be expanded as a system grows. Simply select the information you need, set the parameters, choose the scan time, and decide on the degree of reporting.Buffer storage of short-term monitoring of a number of analogue channels permit the user to view the recent history of motor data such as: motor average load, unbalance, motor current, ground fault, reserve thermal capacity, plus all of the settings of the protective device.A decision can be made to freeze the stored information after the motor stops or after the motor starts. Then the user is able to recall the conditions and diagnose the performance and the cause of the abnormal condition. Typical scan times range from ¼ second to 5 seconds ."

Jan 1, 1992

By E. S. Moore

In the townships of Genoa and Marion, Subdury Mining Division, Ontario, there is a group of twenty-three mining claims known as the Jefferson claims. They are controlled by the Jefferson Mining Corporation and they were staked in 1908 by W. E. Smith, formerly of Sudbury, Ontario, and now of Smith & Reitz, a law firm of Minneapolis, Minnesota. These claims were staked for iron ore and in 1910 about 4000 feet of diamond-drilling was done on them. During the drilling operations galena and sphalerite ~were found in the iron formation in cores from holes, Nos. 2 and 3, claim W. D. 717, Genoa township. This discovery lead to a search for galena and sphalerite in the vicinity and a streak of rock containing these minerals was found in the iron formation a short distance to the east of. the drill holes. A shaft was sunk on this outcrop in 1912 to a depth of 8 feet and bottomed in an attractive lens of galena. Stripping revealed other small exposures of galena and sphalerite in the iron formation.

Jan 1, 1926

By Y. Zedan

Cutting fluids play important roles during machining, including the reduction of friction and temperature. Using a cutting fluid, however, degrades the quality of the environment and increases machining costs. The aim of the present research work is to study the effect of cutting fluids and their interactions with cutting parameters on the quality of holes during the drilling of 6061-T6 aluminum alloys. The lubrication types and modes investigated are dry machining, flood lubricant machining and minimum quantity lubrication machining (MQL), while the part quality criteria include the surface finish, the dimensional accuracy, and burr forms and sizes. A scanning electron microscope (SEM) was used to investigate the formation of built-up edges (BUE) in the drill flutes as well as the surface texture of drilled holes. It was found that dry machining and MQL machining can produce parts having quality levels comparable to those obtained in wet machining, when using the optimal cutting conditions.

Jan 1, 2011

By Matt Schuett

Antamina Mine Facts • Surface Water Design Principles • Drainage Areas • SEDCAD Modeling • Impacted Runoff Collection • Clean Runoff Collection • System Flexibility • Outfall Construction

May 1, 2004

By Atsushi Sainoki

Blast vibration induced by mining activities, such as stope production blasts, could lead to the initiation of seismic events that inflict damage to mine openings. In this paper, the effect of stope production blasts on nearby fault is examined. First, validation of blast vibration attenuation is performed with a numerical model representing a single blast hole through comparison with that calculated from charge-weight scaling law derived from in-situ data. Subsequently, a mine-wide scale model with a fault parallel to a steeply dipping, tabular ore deposit that is mined out with sublevel stoping method is generated, and the stopes are extracted and backfilled with static analysis to simulate burst-prone conditions on the fault. Based on the stress states, dynamic analysis is performed, in which blast vibration is applied to grid points on a stope wall on the hanging wall side. This assumes 9 blast holes located close to the wall, and blast-induced particle velocities that consider the positional relationships between the assumed blast holes and the stope wall are applied. During the dynamic analysis, blast sequence is considered, and stress states and shear displacement on the faults are examined. It is found from results that, after a rise in normal stress on the fault due to compressive waves induced by the blasts, the normal stress decreases because of the reflection of the compressive waves on the fault. The reduction in the normal stress due to the reflected waves is found to be large enough to cause the fault to slip. The results also show that the level of normal stress eventually keeps decreasing with time as the blast sequence proceeds and that an increase in shear displacement on the fault is accompanied by a decrease in normal stress. This study clarifies the mechanism by which blast vibration causes the fault to slip. In addition, the simulation technique to apply blast vibration that takes into account blast sequence and the locations of blast holes to a stope wall is developed.

Aug 1, 2013

Caterpillar Inc The world's largest manufacturer of construction and mining equipment, diesel and natural gas engines and industrial gas turbines. Technology leader in logistics, construction, transportation, mining, forestry, energy and electric power generation.

Aug 1, 2013

By L. Chunpongtong

The Athabasca oil sands mineable resource is located in northeastern Alberta, Canada. In oil sands mining, the ore zone is regulated to have a minimum mining thickness of 3 m and a cutoff grade of 7 wt.%. The current algorithm that is widely used to flag ore zones and waste zones tends to overestimate oil reserves and causes low-grade ore to be processed. This paper presents the development of a more complex algorithm that is more representative of the actual oil found during operations and that can prevent low-grade ore from being sent for processing.

Jan 1, 2014

By A. A. Brant

"Improving geological and geophysical evaluation should serve to reduce the early-stage risk assessment and there-by contribute to exploration expenditure stimulation. The limitations of present-day methods are reviewed, particularly as to anomaly causes, depth penetration and quantitative physical interpretative abilities. Some of the problems now under study are discussed. Future developments expected include the treatment of quantitized geologic and geophysical data, as well as continuing attempts toward computerized interpretation."

Jan 1, 1967

By L Mariani, G. Mendoza-Suarez

In this investigation, TiH2 powders were coated with copper and nickel by electroless plating to delay hydrogen evolution. Copper-coated samples were found to have a mixed acicular (2D growth) and cauliflower (3D growth) morphology whereas the nickel-coated samples had a cauliflower morphology. Examinations of the coated powder cross-sections revealed that the coating thickness ranges from 0.2 µm to 4 µm. Uncoated areas on the powder surface and coating flakes unattached to TiH2 particles suggest poor adhesion between the coating and the substrate. The phase transformation undergone by the TiH2 during dehydrogenation was studied in samples taken at intermediary points in the heating cycles and examined by XRD. The findings reveal that as the powder is heated from room temperature to 800°C, it changes from TiH1.971 to Tiu and to aTi. Differential Thermal Analysis (DTA) was performed to study the effects of the coatings on the temperature of hydrogen release. It was found that increasing the number of plating iterations, and therefore the thickness of the coating, creates a significant shift in the temperature of gas release.

Jan 1, 2006

By R Chandramohan

Comminution is the science of size reduction of brittle materials. It is integral to mineral extraction and is one of the most energy intensive processes in the mining industry. There are a number of tests used to quantify the strength of ore, which are then used to size the AG / SAG mill in circuit design. The calculated energy utilized for breakage in these devices is based on the assumptions that the materials treated are of average shape and that the processing equipment is designed to break the ore as efficiently as possible under the given operating conditions. In drop weight tests, it was found that shape significantly influences the measured rock strength. Controlled experiments with variations in blends of rock shape show that mill throughput increases with the addition of weaker shaped rocks.

Jan 1, 2012

The principles and utility of in-situ coal gasification are discussed, and a first field test conducted by the Alberta Research Council in 1976 near Forestburg, Alberta, is described. The test was carried out in a 12-ft subbituminous coal seam under 60 feet of cover. Within this seam, a 30 by 60-foot block , containing approximately 650 tons of coal, was delineated by four injection/production holes which were oriented to take advantage of the natural fracture system in the coal. Linkage between holes was established by reverse combustion and gasification was accomplished by injecting air into the ignited coal. No steam was injected but operating pressures were adjusted to utilize formation waters for partial carbon -steam gasification. The coal gasification runs lasted six weeks and gasified an estimated 900 tons of coal ,' during sustained periods of gasification, a fuel gas with heating values of between 110 and 150 Btu/scf was obtained. Plans are now being developed for excavating the test site and inspecting the subsurface cavities created by gasification.

Jan 1, 1977

By F. W. Gray

Ideal utilization of the heat energy in coal should theoretically be secured by supplying each atom of combustible material present with the exact quantity of oxygen necessary for complete combination. An intimate and equal admixture of the fuel particles with air is therefore to be sought. Coal, or the combustible substances of which coal is composed, may be used in solid or liquid or gaseous form. The use of coal in small particles intimately mixed with air is, in effect, a specification of coal in pulverized or dust form. There has been much important development of this manner of using coal, which may be instanced as the outstanding advance in the use of coal as a solid. The completeness and efficiency of combustion in a properly designed dust-fired furnace permits the use of locally available coals of inferior quality, and enables them to be used commercially instead of imported coals of better quality. That is to say, some grades of coal of low calorific value, that are not economically useable in lump form on grates, are useable in pulverised form, because of the more complete combustion thereby obtained, and the consequent more efficient results. In the case of coals that are unsuitable for steam-raising in grate-fired furnaces, because of clinker troubles, (arising usually from a combination of high sulphur content and low-temperature fusibility of the ash content) use in pulverised form has obvious advantages, and in addition gives the benefit of any heat units that are contributed by free sulphur in the coal.

Jan 1, 1924

By James R. Hein, Jane Reid, Robert W. Embley, Se-Won Chang, Randolph A. Koski

"Abstract - This is the first reported occurrence of an active hydrothermal field in an oceanic fracture zone setting. The hydrothermal field occurs in a pull-apart basin within the Blanco Fracture Zone (BFZ), which has four distinct mineral deposit types: (1) barite mounds and chimneys, (2) barite stockwork breccia, (3) silica-barite beds, and (4) silica, barite, and Fe-Mn oxyhydroxide in sediments. All deposit types contain minor amounts of sulfides. In barite stockwork, silica-barite beds, and mineralized sediment, Ba, Pb, Ag, S, Au, Zn, Cu, Hg, Tl, As, Mo, Sb, U, Cd, and Cu are enriched relative to unmineralized rocks and sediments of the BFZ. Fe and Mn are not enriched in the barite stockwork or silica-barite beds, but along with P, Co, and Mg are enriched in the mineralized sediments. Silver contents in deposits of the hydrothermal field range up to 86 ppm, gold to 0.7 ppm, zinc to 3.2%, copper to 0.8%, and barium to 22%.Mineralization occurred by diffuse, low to intermediate temperature (mostly <250°C) discharge of hydrothermal fluids through pillow lavas and ponds of mixed volcaniclastic and biosiliceous sediments. Bacterial mats were mineralized by silica, barite, and minor Fe hydroxides, or less commonly, by Mn oxyhydroxides. Pervasive mineralization of bacterial mats resulted in formation of silica- barite beds. Silica precipitated from hydrothermal fluids by conductive cooling and mixing with seawater. Sulfate, U, and rare earth elements (REEs) in barite were derived from seawater, whereas the REE content of hydrothermal silica deposits and mineralized sediments is associated with the aluminosilicate detrital fraction. Fe-, Zn-, Cu-, Pb-, and Hg-sulfide minerals, Ba in barite, and Eu in all mineralized deposits were derived from hydrothermal fluids. Manganese oxides and associated elements (Co, Sb, Mo, W, Cl, and Cu) and Fe oxides and associated elements (Be, B, P, and Mo) precipitated as the result of mixing of hydrothermal fluids with seawater."

Jan 1, 1999

By J. Lu, J. B. Wiskel, D. G. Ivey, E. Niemi, H. Henein

Simulated TMCP using a Gleeble was undertaken to evaluate the effect of the austenite to ferrite cooling rate, coiling temperatures of either 400°C or 500°C and the magnitude of plastic deformation at the coiling temperature on the hardness of a Grade 483 (X70) steel. For comparable apparent cooling rates and deformation conditions, the hardness of the samples were independent of coiling temperature The application of a minimum compressive deformation > 8% was required to increase hardness at both simulated coiling temperatures of 400°C and 500°C. An increase in hardness was also observed with increased cooling times between 800°C and 500°C (i.e., slower cooling rates).

Jan 1, 2005

By R. T. Erskine

"The No. 6 orebody is located 6 miles from the main op.eration of Brunswick Mining and Smelting Corporation Limited and includes open-pit and primary gyratory crushing facilities. Ore is transferred by truck to the secondary crushing facility at the main plant. About 3,500 tons of ore per day are crushed to minus % in. and ground to 68 per cent minus 400 mesh in rod and ball mills for flotation feed. Conditioning and aeration precede rougher flotation, and four stages of cleaning bring concentrates to a grade of 42 per cent Pb + Zn + Cu. Middling products are reground and refloated in a secondary flotation circuit, producing a cleaner feed and a final tails product. Primary bulk concentrate is treated with sulphur dioxide and steam-heated to l 70°F and the majority of the gangue is floated off, leaving a product that assays 57 per cent combined Pb + Zn + Cu and is suitable for marketing. This material is thickened, filtered, dried and loaded into railway cars for shipment to the smelter. Reagent use on flotation is conventional, with many compromises in dosage required to maintain the recovery of lead and zinc in the most advantageous proportions. Many refinements in the flowsheet have been made since start-up in 1966, and more may be made as laboratory and plant testwork indicate possible improvements."

Jan 1, 1971

By V. Schwinn, P. Fluess, N. Cauderlier, J. Bauer

From a strategic and economic point of view, the development of fine grain high strength steels for long distance pipelines is intensified world wide to satisfy the demand for natural gas in the future.The project related property profiles based on strength, toughness, crack arrest and sometimes resistance against HIC at defined design temperatures require an effective structural refinement using advanced steelmaking and processing in the rolling mill. The microstructure of modern line pipe steels ranges from ferritic pearlitic to ferritic-bainitic and structures where bainite is the dominant component, possibly upgraded by secondary phases. This paper illustrates microstructures and properties of recent orders on line pipe steels both for onshore and offshore application using different processing routes in the plate mill. Examples will be given for SAWL 485 offshore grades, X65 HIC and X70 HIC onshore grades, respectively. Finally, production results of a recent X80 order will be presented.

Jan 1, 2005

By J. Stumper

The control of the distribution and movement of liquid water is crucial for increased reliability and durability of PEM fuel cells: whereas the proton exchange membrane requires a minimum amount of liquid water for optimum operation, water excess in the GDL will impede reactant gas access to the catalyst layer thereby reducing performance. In order to understand the relationships between water management on one hand and fuel cell performance and durability on the other, Ballard has been developing a number of minimally invasive techniques that can throw light on the role of liquid water for both cell performance and durability. This paper introduces a novel measurement method that can provide information about the amount and distribution of liquid water under operation. It is shown how the MEA Resistance and Electrode Diffusivity (MRED) method can be used to determine i) the amount of liquid water in the fuel cell, ii) the pure ohmic cell resistance and iii) the O2 -diffusivity of the cathode. Furthermore, through a combination of the MRED method with current mapping it is possible to determine spatially resolved MEA resistance profiles.

Jan 1, 2005

By Denis Blackburn

La Direction générale du développement de l?Industrie minérale (DGDIM) du ministère des Ressources naturelles et de la Faune (MRNF) du Québec tient un inventaire de toute l?activité minière sur le territoire. Cet inventaire s?est enrichi, au cours des dernières années, d?un grand nombre de projets dédiés au fer ou à des substances qui y sont associées (titane, vanadium, phosphate). Actuellement, cinq régions du Québec sont principalement touchées par la recrudescence de projets dédiés au fer : Fermont, Schefferville, Baie d?Ungava, Baie-James et Chibougamau. Fermont et Schefferville sont les régions les plus actives. Les infrastructures en place, telles que les routes, les chemins de fer, les ports, les lignes électriques et les municipalités, ont atteint, dans certains cas, leur capacité et de nouvelles infrastructures devront être construites pour satisfaire les besoins. À la Baie-James et sur le flanc ouest de la Baie d?Ungava, des projets d?exploration sont aussi en cours. Le manque d?infrastructure pourrait peser lourd sur le développement de projets miniers dans ces régions. Enfin, dans le secteur Chibougamau/Matagami et à quelques sites ailleurs au Québec, des projets d?exploration qui visent le vanadium, le titane ou le phosphate pourraient aussi fournir comme produit secondaire des concentrés de fer. Tous les projets, décrits dans cet article, sont situés sur le territoire du Plan Nord du gouvernement du Québec.

May 1, 2011

By D. H. Ryan, B. Abdul, M. Pernechele, E. Asselin

Hydrometallurgical processing of sulphide concentrates at medium temperature (150°C) produces residues, which contain valuable metals (Cu, Ni) as well as sulphur and iron bearing minerals and phases. The low solubility of iron during the medium temperature processing of sulphide ores can favour the formation of poorly crystalline, nano-scale iron oxide/oxyhydroxide phases. A better understanding of the formation and structure of these iron precipitates may elucidate key factors that would ultimately result in lower valuable metal losses and more stable leach residues. Residues from two medium temperature leach processes were characterized by Mössbauer Spectroscopy. Some portions of the Mössbauer Spectrum were suspected to be linked to jarosite but could not be positively identified as such. There was a broad range of disorder and substitution present in the material and solely attributing it to jarosite proved difficult. Various synthetic jarosites with Cu substitution were precipitated for Mössbauer analysis. These were then characterized by Quantitative X-Ray Diffraction (QXRD), Scanning Electron Microscopy (SEM), Inductively Coupled Plasma Mass Spectroscopy (ICP-MS) and Mössbauer Spectroscopy. The Mössbauer Spectra of the synthetic jarosites is compared with that of the residues from medium temperature (150°C) sulphide concentrate leaching.

Jan 1, 2014

By Garston Blackwell

Abstract - During geostatistical estimation of block grades, the kriging process produces a measure of error, the kriging variance or the kriging standard deviation. Estimation of the block error depends on the semi-variogram model for a deposit, which reflects fundamental characteristics of a deposit such as (1) nugget effect, (2) range of influence of grades, (3) different local spreads of data as a function of average grade (proportional effect), (4) nested structures, and (5) underlying anisotropies in the data; this model may be affected by sampling or assaying limitations, however. Because the kriging error incorporates so many features of both the deposit and data to be used for estimation, it may offer a substantial improvement on block classification over traditional procedures such as data density. Practice indicates that the relative kriging standard deviation (RKSD) is particularly useful for block classification in measured, indicated and inferred categories. Plots of RKSD in plan and section also can be used to demonstrate where extra drilling and sampling would be most advantageous for upgrading the class of some blocks. Moreover, the use of grade and RKSD filters can show where material near cut-off grade is poorly defined, indicating sampling target areas to improve block classification in the vicinity of the ore-waste boundary.

Jan 1, 1998