Search Documents

By Steve Piercey

Introduction ? VMS Deposits: The Target ? Key points for every belt: heat flow and extension. ? Good felsic rocks ? Good mafic rocks. ? Petrochemical assemblages. ? Summary Key Points Throughout ? Common themes: ? Heat ? driver of the hydrothermal system ? Extensional geodynamic setting ? conduits to focus fluid flux ? (e.g., Lesher et al., 1986; Swinden et al., 1991; Barrie et al., 1993; Lentz, 1998; Syme et al., 1999; Piercey et al., 2001, etc.) ? We must identify rocks, belts and tectonic environments that encompass these two criteria (among others but?) ? e.g., forearc rifts, intracontinental rifts, arc rifts, and back-arc basins.

Apr 1, 2005

By G. Mousavian, R. Bagheri, N. Dalili

Polypropylene (PP) and its composites have an increasing use in automobile and domestic industries. Since the published results on strain rate effect on yield behavior do not match, and there is a high attention paid for effect of nanometeric fillers on deformation behavior of composites, in this research the strain rate effect on yield behavior of PP and the effect of nanometeric fillers on deformation behavior of PP have been studied. Microscopic observations and tensile tests in different strain rates on neat PP samples and on samples filled with 5, 10 and 15 %wt have been used. A dramatic change in behavior for the modulus and post-yield slope curves when the strain rate is between 0.0433-0.05 s-1 has been observed. Microscopic observations on PP indicate a change in deformation mechanism from shear yield to crazing at the same strain rate that the change in behavior of curves occurs. It has been observed that in PP nanocomposites with higher amount of calcium carbonate, fracture in early stages of deformation occurs in lower strain rates. In other words for a fixed stain rate there is a critical filler percentage such that if the filler percentage is higher then early-stage fracture will occur. Similarly for a fixed filler percentage there is a critical strain rate and in higher strain rates early fracture will occur. The critical stain rate will decrease as the filler percentage increases and vice versa.

Jan 1, 2006

By Thomas J. Ferree

"IntroductionThe objective of this chapter is to provide important criteria relating to the operation and maintenance of spiral concentrators and Reichert cones, so that optimum performance can be achieved and maintained in a mill circuit. Little space will be devoted to the theory of the forces of separation or the technical details of the devices, as that in(ormation is available from other sources. The discussions in this chapter will be presented in a manner that should be interesting and useful to anyone who may be exposed to these methods of gravity separation. It is most important for the reader to understand that each application of the equipment should be considered on its own merit, as no two suites of minerals respond exactly alike in mineral processing circuits. The information herein should be useful as a guide toward increasing the metallurgical efficiency of the processes, irrespective of the type of minerals being concentrated.It is highly recommended that certain tools be made available to the personnel responsible for metallurgical performance of the spirals and cones; these include a set of standard type laboratory screens, a medium quality petrographic microscope, and a vanning plaque or gold pan. These devices, when used in conjunction with a basic understanding of the mill circuit, provide immediate knowledge on the characteristics of any sample in the mill circuit. The information gained by visual evaluation of sized fractions of products can solve many of the basic problems of mineral beneficiation, and at the same time increase the interest of the non-technical personnel associated with the plant operation. There are many problems associated with obtaining satisfactory performance from a mill operation. Many of the problems have to be solved using a technical approach. Some of the problems, however, can be solved with practical knowledge and common sense. It is hoped this chapter can provide a guide to both techniques."

Jan 1, 1989

By Peter Moon

THE mineral industry of Canada relies heavily upon the talent of its technical men. It is vital to the well-being of the industry that its supply of young, trained men be adequate. At the present time, the industry is acquiring only 200 new graduates a year. The shrinking supply is far below present and future requirements. Other industries and research organizations are competing for engineers and scientists. Dr. J. B. Mawdsley (1), Past-President of the Canadian Institute of Mining and Metallurgy, has recently outlined a program designed to attack the problem. Dr. J'. C. Sproule (2), another former President of the Institute, has stated that: "The need for selection of trainee material is commonly recognized, but little is done about it." The following paper contains a short discussion of occupational interests, and outlines research, using psychological knowledge and measuring techniques, aimed at the identification of desirable recruits for the mineral industry.

Jan 1, 1963

By P. Leo

Al-Mg-Si alloys are widely used as medium-strength structural materials; extrusion is the most common processing route. In the present hot deformation investigation of a 6060 alloy, the microstructure of the alloy has been analyzed in the as-cast state, after homogenization heat treatment and after hot deformation by tensile tests in the range 400-490°C and 10-4 to 10-2s-1 on both as cast and homogenized alloys. After deformation the microstructure of the as-cast alloy exhibited cavitation. The flow curves at the lowest test temperature T show a gradual softening after a stress peak, being more evident for the alloy deformed in the homogenized state in association with a high yield stress; at higher T a plateau is attained which is lower as T rises and strain rates decrease. For each fixed T, the ductility decreases as strain rate increases for the homogenized alloy whereas, for the as cast alloy, it rises with strain rate. Constitutive analysis gives Q = 240kJ1mol for the homogenized alloy in agreement with published values; this indicates a more rapid strength decline with rising T than Al, suitable for good hot workability along with the lack of cavitation.

Jan 1, 2011

By Pierre Bernard

Contents of the presentation ? Overview of Brunswick 12 Mine ? Brief description of the mine geology ? Summary of the current Mineral Reserves and Additional Mineral Resources ? Review of the ongoing mining remnants evaluation process, particularly emphasizing the integrated work between the mine geologists, the mine engineers and the metallurgists ? Challenges and opportunities to extend the mine life

Apr 1, 2005

By R. W. Lawrence, O. Lopez

Many gold deposits in the world have not been developed clue to the presence of copper and other base metals which can cause metallurgical and environmental challenges clue to the formation of base metal cyanide complexes. SART technology (sulphidization-acidification-recycle-thickening) can resolve these issues by recovering copper as a high grade sulphide concentrate, recycling the associated cyanide back to the gold leach, and eliminating the downstream environmental liabilities. Project economics can be improved substantially, leading to a positive re-evaluation of new and existing gold-copper projects. Some aspects of the design and operation of two recently commissioned SART plants will be discussed.

Jan 1, 2011

By Chuan-liu Wang

The bionic non-smooth surface has the characteristics of anti-wear, and reducing resistance. Based on bionic non-smooth surface?s characteristics, a bionic drill bit was developed. When the bionic drill bit is used, a bionic non-smooth surface forms on the crown of bionic drill bit. This surface can be used to extend the life of drill bit and improve drill efficiency. The bionic unit diameter and arrangement were researched in this paper to determine the optimal bionic non-smooth surface for further improving the life and efficiency of drill bit. Four bionic samples having the same structure size, materials and arrangement were designed and manufactured. After being sintered, the abrasion ratios of the four bionic samples were tested, and the results show that the abrasion ratio of Nos. 3 and 2 were similar (only 2% difference) and higher than that of No. 1 and 4. Therefore, the optimal diameter of bionic unit is 1.5 and 2.0 mm. Small diameter bionic drill bits were designed and manufactured, and tested in the laboratory. The results show that not all bionic structure bodies are better than normal diamond bits, except the bionic unit arranged in a reasonable range. When the angle was 24° and 30°, the arrangement of bionic unit were more reasonable, which shows the superiority of the bionic coupling bit.

Aug 1, 2013

By Mark Holdsworth

In 2002, Kennecott Utah Copper Copperton Concentrator installed an Expert Control system for optimization of their SAG and Ball milling circuits. The advanced process control has been well received and is utilized well over 95% of the time. In the years since, many lessons have been learned and many advances have been made. Improvements have produced millions of dollars of benefits and have included directly controlling feedrate with complex logic as opposed to using a bearing pressure controller, modifications to how sound is used for control, modifying logic for maximizing asset utilization and using advanced control for automating equipment restart.

Jan 1, 2012

By X. Cao

Friction stir processing (FSP) is used to produce wrought microstructures at the surface of sand-cast aerospace grade magnesium alloy ZE41A-T5. It is found that the microstructure is significantly refined in the stir zone and the flow arm. The stir zone is largely comprised of equiaxed magnesium grains of approximately 4.5 pm compared with about 50 µm in the base cast material. In the stir zone, however, abnormal growth of some grains is also observed. Vickers microindentation hardness tests indicated that the stir zone experiences some increases in hardness. Single surface passes with low distortion, lack of pores and cracks were successfully obtained indicating the great potential of the FSP technique for modifying, improving and repairing magnesium alloy castings. This will probably open new opportunities to apply magnesium alloys in aerospace industry.

Jan 1, 2007

By N. E. Nelson

"The Hidden Creek mine is about l~ miles north of the north end of Granby bay; a nearly landlocked body of water on the west side of Observatory inlet; 90 miles north of Prince Rupert; British Columbia.The main haulage way of the mine at 385 feet above sea-level has been driven north into the somewhat precipitous end of a north-south ridge that rises from the tide flats between the east and west forks of Hidden creek. The outcrops of the principal orebodies, two prominent bluffs of stained rocks and sulphides, were higher on the face of the ridge and extended from about 530 to 850 feet elevation. North from the bluff tops, the ridge comb rose gradually to about 1,200 feet elevation. The name of the discoverer and the date of discovery of the Hidden Creek orebodies are probably unknown, but the discoverer is believed to have been an Indian from one of the reservations along Observatory inlet. The deposit was brought to the attention of John Flewin, Government Agent at Post Simpson, near the beginning of the present century. Mr. M. K. Rodgers, developer of the Nickel Plate mine at Hedley, did the first organized work on the deposits. Next the Hidden Creek Copper Company prospected the property. Rodgers acquired the prospect a second time, did more work, and finally in 1910 optioned the property to the Granby Consolidated Mining, Smelting and Power Company, Limited, at that time operating at Phoenix and Grand Forks in the Boundary district of British Columbia. The optionees stepped up the development work and brought the property to production in 1914. The ores were direct smelted until 1924. In that year a mill was built. From 1930 until the end of the productive life of the properties in 1935, all of the ore was milled and the concentrate smelted. From March 17, 1914, until July 31, 1935, the production from the Hidden Creek mine was, in round numbers, 18,000,000 tons of 1.70 per cent copper ore and 6,000,000 tons of low grade dilution rock. The Hidden Creek mine ""died with its boots on"". During 1934 the average monthly production was 146,377 tons of 1.06 per cent copper ore. For 7 months of 1935 the average was 161,750 tons of 1.03 per cent ore, and for the final month, July 1935, the production was 156,950 tons."

Jan 1, 1954

By Zhiqing Zhang, Changyun Chen, Qing Liu, Lin Lin, Zhihong Jia, Guangjie Huang, Lipeng Ding

The effect of interrupted quenching (IQ) treatments on natural aging and bake hardening response of Al-Mg-Si alloy was investigated by hardness measurements, tensile test, differential scanning calorimetry (DSC) and transmission electron microscopy (TEM). The results show that interrupted quenching at 100oC could effectively suppress natural aging and improve bake hardening response. The optimized interrupted quenching treatment is 100oC for 45min, which gives the alloy a relatively low T4 temper strength and higher bake hardening response. The formation of highly dense cluster(2) during the interrupted quenching could be the reason for suppressing the natural aging and accelerating the precipitation of ß? phase during the paint bake treatment. In addition, interrupted quenching at higher temperature (170oC) results in unfavorable properties in both T4 temper and paint bake treatment. The formation of large precipitates is responsible for these undesired effects.

Jan 1, 2015

By K. Ebrahimi-Nasrabadi

The dependence between the extent of conversion of cryptocrystalline magnesite to caustic magnesia was studied experimentally in the temperature range of 400?1200 °C and for calcination times up to 8 h. A TGA?DTA analysis showed that decomposition begins at temperatures as low as 340 °C and is completed at 600 °C. Measurements of specific surface area (SSA), iodine adsorption number (IN), crystallite size, and loss on ignition were carried out to characterize the product quality. It was found that while all the parameters are dependent on the extent of calcination, densification of the product caused by grain coarsening affects their final values. As a consequence, SSA and IN went through a maximum with time. The study showed that high quality caustic calcined magnesia can be produced in a narrow range of temperature (600?650 °C) and time (1?4 h). Medium quality caustic calcined magnesia can be made within a wider range of parameters.

Aug 1, 2013

By H. Wotruba, L. von Ketelhodt, M. Kowalcyk, C. Kleine, M. Robben

Sensor-based sorting is a financially and technically viable technique that is operating with little or no water and relatively little power consumption. Sensor-based sorting has already proven its operational stability at two gold applications in South Africa. Sensor-based sorting cannot only turn waste dumps and diluted mining blocks into reserves. The implementation can also cause a decrease in specific operating costs of mill and mine when for example replacing selective mining by bulk mining methods with subsequent sorting. Successful installations, operational experience, test work data and flow sheet integration from mine-to-mill underline the impact and potential that sensor-based sorting can have on the gold mining and processing industry.

Jan 1, 2011

By S. A. Kenzap

Risk & Uncertainty ? Uncertainty about a situation can often indicate risk, which is the possibility of loss, damage, or any other undesirable event. Most people desire low risk, which would translate to a high probability of success, profit, or some form of gain. Risk = Likelihood x Consequence Risk is the possibility of loss, damage, or any other undesirable event.

Oct 1, 2010

By D. D. Liu

This paper proposes a charge induction dust measurement method based on detrended fluctuation analysis (DFA) for use in coal mine environments, based upon electrostatic interference, dust properties, wind speed, particle size, moisture content and other factors. In this methods, sequence x(t) is first obtained through a dust concentration sensing probe, and then the cumulative deviation y(t) is calculated, and y(t) is divided into same lengths. Secondly, a first-order linear fit is used for data of each interval, and mean-square deviation filtered DFA was calculated for each interval. Finally, the dust mass concentration of the corresponding time is obtain by supplemented calibration coefficient and fitted the data point which is the mean and square root for all lengths of interval. Simulation and verification experiments showed that the charge induction dust measurement method based on DFA can reduce coal mine electrostatic interference effects with high accuracy. The design has been successfully applied to select areas.

Aug 1, 2013

By G. Bonnivard

"A complete laboratory process for the treatment of lateritic ores containing a high proportion of iron, as well as chrome and alumina, has been established. The ores treated originate from the tropical zones and result from superficial climatic alteration. According to recent estimates, the known reserves of such ores reach many billions of tons, thus representing huge potential reserves for the elements they contain.The process used is based on the alkaline roasting of pelletized ore in the presence of sodium carbonate. This treatment results in the separate recovery of pellets of upgraded iron ore, pure chrome oxide and hydrated alumina. The research described in the paper aims at determining the best experimental conditions for obtaining the highest extraction of the required oxide from this type of ore."

Jan 1, 1967

By Pierre Antoine Dhaiti, Gilbert Sergerie, Michel Dagbert, Jean-Maurice Brodeur

"Quality of iron ore is generally determined by several factors which can be correlated or independent. Among these f actors, we generally find per cent iron, silica, magnetite or hardness. Forecasting the short- and long-term fluctuations of these f actors in the future pit is an important feature of mine planning in these deposits. Computer simulation provides a realistic answer to these questions. It allows to generate values for the most important quality features of each shovel load with the proper correlations between them as well as between one load and the next being fully reproduced. Then different sampling schemes f or grade control or blending facilities can be examined on the simulated data. The mechanics of the simulation procedure and its potential applications are described in an example.IntroductionThe purpose of this paper is to illustrate the use of in-situ grade simulation in the planning o f the grade control in an iron ore min e. More precisely, given a production unit of given size, we need to know how many samples have to be collected in that unit so that we ca n recognize its grade with a reasonable precision. Conclusions that we would like to arrive at are of the type: with 4 blasthole samples we ca n get the iron grade of a 10,000 ton bloc k with less than a ± 2% Fe error 95% of the time.The approach t hat we take to solve this problem is simulation. We simulate the grade of samples and the grade of the block that contains these samples. We repeat the simulation for hundred s o f blocks. By comparing the sample grade with the block grade in each case, we determine the actual number o f blocks where the difference sample-bloc k is less than a given limit."

Jan 1, 1983

By M. M. Holgate

"Porosity neutron deflection scales can be derived more easily by cumulative correlation than by the conventional method of plotting corresponding points on a graph. The micro-log can be used as a porosity datum for the neutron log by transforming the permeability cut-off it shows to a porosity cut-off by a permeability-porosity function obtained from core analysis. Porosity footage values calculated in this manner from the neutron log are within 20 per cent of core analysis values."

Jan 1, 1960

By T. Grammatikopoulos, K. Gibbs, H. De Souza, C. Gunning

The mineralogy of any ore body is a key factor in defining ore zones and predicting minerals/metals behaviour during processing. The determination of forms of gold, defined as the different chemical states in which gold is encountered in ore deposits, is critical. The most commonly known form is that of gold minerals and alloys, while other forms of gold have been collectively described in the literature as submicroscopic gold (i.e., less than 1 µm in diameter). Gold mining operations generally deal with very low-grade ores, in the order of a few g/t, in which gold displays complex mineralogy. These difficulties complicate the mineralogical studies and pose challenges for processing and recovering the gold. A comprehensive understanding of the chemical forms of gold is necessary to define gold mineralization and optimize gold metallurgy. SGS Canada Inc. has been using QEMSCANTM and a Tescan automated SEM that are automated mineralogical techniques that provide vast amounts of data for microscopic Au. The data in conjunction with other physical and chemical methods provide a comprehensive delineation of the ore composition and behaviour.

Jan 1, 2011