Search Documents

By M. E. Moraes Castanho de Almeida, A. Ribeiro Cotri

Recovery of cobalt to produce high grade cobalt sulfate from cobalt concentrate by leaching and solvent extraction was investigated. The PLS typically contains Co 10g/l, Mg 2g/l, Fe < 10ppm, Mn < 200ppm, insolubles <100ppm and is extracted with 20wt% Cyanex??272. The typical strip solution contains Co 60g/l, Mg 0.03g/l, and was sent to the current process for the production of cobalt sulfate heptahydrate. The cobalt yield of the plant with two extraction steps was 92%, with three steps was 97% and with four steps 99%. The extraction stage used the concept of "scrubbing" in a countercurrent system. In the first stage of extraction pH was 4.8, and in the last stage of extraction pH 5.5 to promote the exchange of magnesium in the organic with cobalt contained in the PLS. Following the extraction, when using two scrubbing stages, Co/Mg selectivity between of 2,000-3,000 was obtained, and with three scrubbing stages, selectivity was greater than 6,000. The desired selectivity was reached when using a scrubbing configuration with O/A ratio of 10:1. The typical cobalt sulfate heptahydrate had the following composition: Co 20wt%, Mg < 0.01wt%, Fe < 5ppm, Mn < 0.01wt%, Cu < 0.01wt%, Zn < 0.01wt%.

Jan 1, 2014

By Fridrik J. Kristjansson, Stephen R. Hicock

"Three varieties of till are recognized in the Beardmore-Geraldton area: local lodgement till, nonlocal carbonate till, and local supraglacial till. The local lodgement till unit is examined in detail for the first time in this paper. It is the best potential overburden exploration medium for gold and other metals because its particles were locally-derived and deposited subglacially, probably within a few kilometres downglacier (southwestward) from their sources, and have not been diluted by distantly-derived glacialdebris. Both local tills are richer in gold and other metals, relative to nonlocal carbonate till. Local lodgement till rests on bedrock and was encountered frequently at or near the surface in thin drift/bedrock terrain (a widespread terrain type within the west half of the study area), and commonly at the base of boreholes in thick till terrain.INTRODUCTIONDrift prospecting in areas of glaciated terrain has been well documented (in a variety of journal publications and symposium volumes; e.g . Strobel and Faure 1987; MacDonald and Mills 1988) and has proven valuable especially where overburden thicknesses hinder traditional exploration techniques. Drift prospecting techniques may well prove valuable in the Beardmore Geraldton area. This applies especially to the Wildgoose Lake Turkey Lake area where a thick and laterally extensive sheet of nonlocal carbonate till has impeded conventional mineral exploration programs (Fig. I; note the lack of gold occurrences around Wildgoose Lake).Till in .particular has been cited as the best prospecting medium among the various types of glacial sediment (e.g. Shilts 1984). Three end member till varieties are recognized in the study area: (I) local lodgement till which rests directly on bedrock; (2) non local carbonate till; and (3) local supraglacial till which occurs predominatly within, or just downglacier of, upland areas where it commonly mantles the other till varieties. Previous authors have documented how the non local carbonate till hinders gold exploration (Geddes and Kristjansson 1986; Karrow and Geddes 1987; Kristjansson 1986; Hicock 1986, 1987a, b, 1988; Kristjansson and Thorieifson 1987; Thorleifson and Kristjansson 1987, 1988a, b) and why the local supraglacial till may be a good unit for prospecting (Hicock 1986). One detailed surficial geology map sheet of the area has been published (Kristjansson et al., 1988) and others are in preparation. Closs and Sado (1981) reported on the geochemistry of soils and glacial sediments in the west half of the study area. This paper documents the local lodgement till unit and demonstrates why it is the best overburden unit to use for drift prospecting."

Jan 1, 1989

By Jochen Petersen, Alison Lewis, Cledwyn Mangunda

Run-off and waste water streams high in dissolved metal content are generated in all mining operations. The metals pose a threat to life due to their persistent bio-accumulative toxic (PBT) characteristics. Hence, there is a need to treat mine waste water effectively. Lime precipitation is the technology of choice through which Fe, as the major metal species, is removed as Fe (III) oxyhydroxides with other metals co-precipitated and/or adsorbed. Sulphates are removed as gypsum or incorporated into the Fe phases. The resulting sludge has poor dewatering characteristics and is deposited in landfills, with an inherent risk of returning the Fe back into the water cycle through leaching. This study seeks to understand the mechanisms behind the formation of this sludge in terms of product quality. The relationship between process conditions and product characteristics has been investigated through exploring the effect of Fe (III) concentration on the precipitate product characteristics (particle size distribution (PSD), size, morphology and structure) and quality (in terms of filterability, settling ability, etc.) in a simplified system. Neutralisation of acidic synthetic aqueous Fe (III) sulphate streams containing 50, 400 and 800 mg/L Fe(III), respectively, was effected by mixing it in a continuous stirred tank reactor (CSTR) with dissolved calcium hydroxide for pH control at a residence time of 15 minutes. Precipitate samples analysed for morphology and PSD, using nanoSEM and Zetasizer respectively, showed a general decrease in PSD and zeta potential with increases in feed Fe (III) concentration. These results were used to infer the particle size enlargement mechanisms of Fe (III) oxyhydroxide precipitates under a given set of operating conditions. Preliminary product quality results indicate that a high concentration (800 mg/L) leads to the rapid formation of metastable precursors with poor product quality, whilst a low concentration (50 mg/L) leads to formation of thermodynamically more stable precipitates with good product quality. The approach demonstrates a potential route forward in terms of linking operating conditions to the attainment of desirable characteristics rather than specific precipitate phases which are difficult to identify.

Jan 1, 2016

By R. Chen, K. Xia

In deep mining activities, blasting induced compressive stress wave would be reflected as tensile wave at a free surface around the openings, which would facilitate the tensile failure of the deep rock since it is much weaker in tension than in compression. It is thus critical to understand the dynamic tensile failure of rocks subjected to static tension for deep rock engineering applications. A modified split Hopkinson pressure bar (SHPB) system is adopted to load Brazilian disc (BD) samples statically, and then exert dynamic load to the sample through stress wave generated by impact. The pulse shaper technique is used to generate a slowly rising stress wave and thus to facilitate the stress equilibrium of samples during each test. Five groups of Laurentian granite (with tensile strength of 12.8 MPa) BD samples under the pretension stress of 0 MPa, 2 MPa, 4 MPa, 8 MPa, and 10 MPa are tested under different loading rates. The result shows that the dynamic tensile strength of the rock decreases with the increase of pre-tension stress, which is easy to understand because pre-tension stress weakens the rock sample. It is also observed that under the same pre-tension stress, the dynamic tensile strength increases with the loading rate, revealing the so-called rate dependency that is common for engineering materials. Furthermore, it is found that the loading rate sensitivity of the rock increases with the increase of pre-tension stress. A qualitative explanation for this phenomenon is that more microcracks are generated and activated under higher pretension stress, resulting in a more viscous material. Based on the results, an empirical equation is proposed to fit the data and explain the dynamic tensile behaviour of rock under pre-tension stress. A physical model is used to simulate the dependency of the dynamic tensile strength of rock on the pre-tension stress and the loading rate, which is shown to be in good agreement with the experimental results.

Jan 1, 2015

By J. Currie, J. McManus, R. Chenier

"Cominco Copper Division&apos;s Valley Mine is located in the Highland Valley of British Columbia, approximately 275 km by air northeast of Vancouver. The nearest towns are Logan Lake, located IS km to the east and Ashcroft, located about 50 km to the northwest.Preproduction stripping of rock and overburden at the Valley Mine&apos;s Lake Zone Pit began in mid-1982 following a decision to discontinue mining in the adjacent Jersey Pit. Equipment and mining methods were carried over from the Bethlehem Copper operations which, with Valley Copper Mines, were merged into Cominco in December 1982.Blasting practices, as carried over from the Bethlehem pits, were designed to provide the fine fragmentation required to meet production requirements using the Bethlehem crusher. However, after mining the first few benches of the Lake Zone Pit, it became apparent that overblasting at the pit limits was causing a number of bench failures, as well as contributing to an over-all reduction of the material strength of the rock mass forming the southwest wall of the pit.With present ultimate pit plans calling for the southwest wall to be as high as 300 m, Valley staff realized that potential slope stability problems should be dealt with as early as possible. This philosophy would enable experimentation on phase pit walls in order to attain the optimum slope angle on the ultimate pit wall.As part of an over-a ll slope stability program, a controlled blasting program was initiated at the Lake Zone Pit in March 1983. In this program, Valley engineering and production staff worked together with Golder Associates in establishing design criteria and evaluating the results. This program resulted in a marked improvement in the soundness of pit walls while maintaining the required degree of fragmentation."

Jan 1, 1985

By B. B. Meadows

"The Minto-Chipman Strip Mining Reclamation Project was initiated to re-vegetate the spoil piles remaining from strip mining operations.All available information was studied by the team responsible, and areas being reclaimed in the U. S. were visited, Methods applicable to the N. B. Project were noted for future use.We have both surface and underground mining operations in New Brunswick, Both deface the natural landscape and reclamation varies in difficulty, Surface operation disturbances are the most difficult to correct.Some of the surface mining is carried out next to two main highways and the results are definite eyesores, With this in mind, it was decided to landscape the spoil ground next to the highways and plant “as is"" the ground remote from the public view.The landscaping entailed various degrees of bulldozing from complete levelling to contouring, smoothing and topping, Bulldozing is, of course, the most expensive part of any reclamation project.There are two phases to the planting program; experimental and operational--experimental both prior and, later, in conjunction with the operational planting.Initially in the experimental project, the pH and composition of the spoil was determined using a grid sampling system. Soil samples were tested in a laboratory at the University of New Brunswick."

Jan 1, 1970

By L. S. Jen

Canadian copper, nickel, zinc, lead and molybdenum mines are characterized by the mining of ores from which more than one metal is recovered. During the 1980s, approximately 15% of the gold, 25% of the zinc, 30% of the copper, 55% of the molybdenum, 80% of the silver and 90% of the lead produced from Canadian mines were produced as co-products and by-products of base metal mining operations. This trend is not expected to change significantly in the near future. The presence of co-products and by-products affects the level of production and the level of revenue from base metal mines in several ways: (I) in general, production of one base metal cannot be expanded or cut back without affecting the amount of production of another metal;(2) the commercial success of certain base metal mining operations depends on the substantial bonus revenues from co-products and by-products; (3) the quality and economic viability of many ore deposits are significantly improved by the presence of co-products and by-products; and (4) while coproduction is critical to the survival of some mines, bonus revenue from by-products can also be life saving to others during economic downturns. For these reasons, deposits with significant co-product or by-product values are likely to continue to be significant targets for exploration and for acquisition.

Jan 1, 1992

By H. P. Pew

THE Pembina oil field is in west-central Alberta, about 88 miles west-southwest of Edmonton. The field, about 35 miles long by T HE Pembina oil field is in west-central Alberta, about 88 miles west-southwest of Edmonton. The field, about 35 miles long by 85 miles wide, is the largest in Canada in areal extent, in the amount of oil in place and in the current producing rate. The discovery well was completed in the middle of 1953. The field has grown until its present area is 369,820 acres. There are 74 working interest owners in the field. Early in the producing history of the Pembina field a committee of operators was formed on a permanent basis. The Pembina Operators' Committee has established a permanent staff, which compiles and distributes pertinent field information on a regular basis to all participants. The Alberta Oil and Gas Conservation Board has dealt with field-wide problems primarily through this committee. Expansion of the field was rapid as shown by the number of wells completed -from 135

Jan 1, 1961

By O. Herstad, J. M. Toguri, K. Grjotheim

DURING the last three years, investigations on the aluminum reduction of magnesium-bearing compounds have been initiated at the Institute of Inorganic Chemistry, The Technical University of Norway. The results of these investigations are reported in this paper. Very little information exists in the literature on the reaction between magnesium compounds and metallic aluminum. The available information itself is conflicting, and, to clarify the existing discrepancy, the reactions between aluminum and magnesium oxide (MgO), caJcined dolomite (CaO . MgO) and olivine (Mg2SiO.) were studied. The logical approach for the study of these reactions between condensed states with the formation of a gaseous phase is, ( 1) the measurement of the equilibrium vapour pressure of the gas, in this case magnesium, associated with the respective reactions and, (2) the identification of the end products of the reaction in order to establish the re-action scheme.

Jan 1, 1962

By S. Borle

The microstructural features produced in friction stir welded AZ31, AZ80 and AZ91 alloys are examined when different welding parameters are applied. The microstructures primarily consist of a-Mg grains with a-Mg + Mg17A112 colonies, however melted films of Mg17A112 are produced in AZ91 alloy when high rotation speeds are applied. When the rotation speeds are slow, or the travel speeds are fast the Mg17A112 were incorporated into the stir zone, however they do not exhibit an elongated lamellar morphology associated with melted films. In the case of AZ80, the extruded base material contains a smaller fraction of Mg17A112 and few of these phases are observed in the stir zones. The results are explained based on the dissolution rate and melting temperatures of Mg17A112 controlling the overall morophology and fraction of phases in the stir zone.

Jan 1, 2011

By J. Janzen

The cost to supply ventilation may exceed 40% of the total mine energy cost for underground mines and is often higher for deeper mines. The goal of Ventilation-on-Demand (VOD) is to ensure that the required quantity and quality of air is supplied to underground mining crews and diesel equipment at the least energy expenditure (minimum cost). A VOD system may include control of surface fans (Supply & Exhaust), underground booster fans, auxiliary fans and automated regulators/dampers to regulate the flow of air with more control elements providing more value. Strategically located Air monitoring stations measure air quantity and quality and provide feed-back enabling control. The modular design involving controls, intelligent instrument and intelligent motor control centres coupled with a communication network allows the quick installation, commissioning and expansion of the system as the mine develops. The result is a very robust, flexible system while reducing maintenance costs and spare parts. This paper discusses the impact of sensors, installation and commissioning on advanced controls and provides solutions for in-field applications.

Aug 1, 2013

By E. Dernedde

A few studies have suggested that the rate of adsorption of hydrogen fluoride on smelter grade alumina is determined by kinetic factors. However, no performance equation for dry scrubbers has appeared in the literature so far. Experimental data from a pilot dry scrubber with co-current flow were compared with results of kinetic models of adsorption, film diffusion and pore diffusion. The pore diffusion model was deemed the most appropriate. It was transformed into a performance equation for steady-state operations of dry scrubbers by the inclusion of the alumina recirculation. Operating results of industrial dry scrubbers with co-current flow were successfully evaluated by means of the performance equation. The average fluoride content of the alumina was also estimated by using the pore diffusion model.

Jan 1, 2011

Mining Equipment Challenges Equipment Availability Unplanned downtime Maintenance Costs Secondary damage and catastrophic failures (T282 $750k) Emergency work is 4x the cost of planned work Inspections Troubleshooting time Incorrect repairs (parts, labor, lost production) Equipment Life Mis-operation of equipment

May 1, 2013

By Hamidreza Soltanzadeh

The injection of CO2 into a reservoir or aquifer can potentially result in deformation, induced fracturing and fault reactivation in the injection zone and/or the rocks that surround it. This paper reviews the data collection and geomechanical analyses performed to assess these potential hazards for the Heartland Area Redwater Project (HARP), in which CO2 sequestration is being considered in a carbonate (Leduc Formation) reef. A three-dimensional mechanical earth model (3D MEM) was developed using available geophysical log data from several wells. The geomechanical response to CO2 injection was studied using a finite element numerical model based on the 3D MEM and pore pressure distributions predicted using a reservoir simulator. The modeling results suggest that the potential for induced fracturing and fault reactivation is low and the maximum predicted ground surface heave is less than 2 cm. Sensitivity analyses conducted with a 2D geomechanical model that was extracted from the 3D model confirm that this conclusion holds true even when a reasonable measure of uncertainty in rock mechanical properties, ambient pore pressures and horizontal stress magnitudes is accounted for.

Jun 1, 2012

By F. Chiesa, Jeremy Carignan, B. Duchesne, D. Levasseur

"Aluminium A206 (AlCu4) is one of the strongest aluminium casting alloys with tensile properties approaching those of ferritic ductile iron. If the specification on the silicon content (< 0.05%) is easy to achieve during alloy ingot production, it is not the case in a foundry, where returns are used which are not perfectly cleaned from the silicate containing molding sand (Olivine). In alloy A206, the Si content is controlled in order to avoid the formation of a low melting point intermetallic phase (such as phase Q Al5Cu2Si6Mg2); these phases will melt during the solutionizing heat treatment to which alloy A206 must be subjected to develop its outstanding mechanical properties. This incipient melting may deteriorate the mechanical properties of Alloy A206 if the solutionizing treatment is applied at the standard temperature of 530°C.In the present study, a lower temperature solutionizing (520°C) was applied to a high Si content 206 alloy in order to reduce or eliminate the possible incipient melting. This was carried out on a complex shape industrial casting weighing 14 kg (31 lb) and 560x410x250 mm (22x16x10”) in size poured in aluminum 206 with a high silicon content (0.22% vs 0.05% max for alloy A206). Twenty ASTM E8 subsize tensile specimens were excised from two locations in the casting in order to compare the tensile properties for the two solutionizing temperature used (530 and 520°C). Optical and SEM microscopy allowed to investigate the causes of the differences in the properties observed between the 2 zones of the casting studied for 3 different heat treatments. INTRODUCTIONIn spite of their “textbook” outstanding mechanical properties (Up to twice the strength and elongation of the widely used A356 alloy), aluminum-copper alloys of the 2xx series are seldom used because of their propensity for hot tearing [Li, 2011], the segregation of copper [Cho, 2003], and their sensitivity to stress corrosion cracking [Jean, 2009, p. 113)]. Also, because of their wide freezing range and high thermal conductivity, a wide mushy zone makes feeding difficult, unless strong temperature gradients are created by liberal use of chills and risers in the critical zones of the part. Because they are prone to hot tearing, grain refining of Al-Cu alloys is particularly important, titanium playing a major role in the process [Sigworth, 2003]; grain refining has also been shown to be beneficial to fatigue strength [Jean, 2009, p. 103]. The practical basis of foundry practices pertaining to these alloys is outlined in an AFS webinar [Weiss, 2014]."

Jan 1, 2016

An Attractive Investment ?Near term low cost and secure PGM producer ?restricted supply legislated demand ?strong pipeline of resource development ?Building Canada?s largest undeveloped PGM-Cu resource ?All work (resource, reserves, DFS, EA) is NI43-101 compliant ?Strong balance sheet: over $8 m in cash with no debt

May 1, 2010

By Y. S. Sun, Northeastern University, W. B. Li, P. Gao, Z. Y. Zhang, J. W. Yu

"The boron-bearing iron concentrate was extracted from ludwigite ore by the process of magnetic-gravity separation. In order to fully utilize the refractory ore and meet the boron consumption of China, a novel process for separation of boron from iron in boron-bearing iron concentrate was proposed in this paper. In particular, laboratory scale experiments of improving boron reactivity were performed. Fine boron-bearing iron concentrate briquettes were reduced by bituminous coal completely at 1125 °C for 150 min. The effect of sodium carbonate, which was used as an additive in the roasting process, was investigated. The addition of sodium carbonate decreased the boron reactivity and facilitated the volatilization of boron. The influence of diverse cooling methods of the reduced samples on the boron reactivity was studied. The results indicated that boron reactivity could reach up to 80.76% when the reduced samples were cooled by rapid water quenching. In addition, the magnetic material containing 92.71 % Fe with a recovery of 95.11 % and boron-rich non-magnetic material containing 14.51% B2O3 with a recovery 88.85% could be obtained by low-intensity magnetic separation. The magnetic material and boron-rich non-magnetic material were good raw materials for steel-making and borax production, respectively.INTRODUCTION Ludwigite ore is abundant in Liaoning province of China, with 28.43 Mt B2O3 accounting for 57% of the boron resources of the country (Liu et al., 2006). However, it has not yet been utilized on an industrial scale due to its complex mineralogy and fine mineral dissemination (Wang, Wang, Ding, Ma & Xue, 2012). At present, boron-bearing iron concentrate and boron concentrate can be obtained from ludwigite ore using magnetic-gravity separation. The boron concentrate contains B2O3 12%~16%, which can be used as a high-quality raw material for the boron chemical industry after activated roasting, but the B2O3 content in the iron concentrate reaches up to 4%~6%. In order to further separate boron and iron from boron-bearing iron concentrate, a blast furnace and a solid pre-reduction followed by electric arc furnace melting have been proposed (Liu, Cui & Zhang, 1998; Wang et al., 2012). However, both of these two current routes face the same crucial problem that molten boron-rich slag has to be cooled slowly to obtain the alkali-dissolution activity of boron, which affects the yield of boron resource."

Jan 1, 2016

By V. P. Mehrotra, D. W. Fuerstenau, A. -Z. M. Abouzeid

The use of pulverized coal for electric power generation results in the production of vast amounts of fly ash. One potential use for waste fly ash is the production of pellets for lightweight aggregates. This paper is concerned with the role of the physical and chemical characteristics of two different fly ashes in governing their agglomeration or pelletization behavior and their strength characteristics. In batch balling experiments, fly ash pellet growth was found to be extremely sensitive to the amount of moisture added. One ash (Mohave) exhibits marked pozzolanic activity whereas the other (Jim Bridger) does not. The pozzolanic activity has a very pronounced effect on pellet growth kinetics, moisture requirements, and the effect of various additives on growth kinetics. Slow drying under ambient conditions produces strong pellets from Mohave ash whereas Jim Bridger ash pellets lacking in pozzolanic activity are weak. Rapid drying at high temperatures results in weak pellets because water necessary for hardening is driven out of the pellet. Steam curing enhances pellet strength. Locked-cycle pelletizing experiments exhibit expected oscillation in pellet production rates and attendant fluctuations in pellet green strength.

Jan 1, 2004

By M. S. Greenfield, E. Cocchiarella, S. Chubbs

"At Dofasco sNo.4furnace a variation of the basic oxygen steelmaking process, Klockner Oxygen Bottom Maxhutte (K-OBM), is used to produce steel. Large amounts of hot gases and particulate are evolved during the oxygen blowing phase. A quencher and a venturi scrubber are used to collect over 99.5% of the particulate. In 1990, the authors investigated the effect of foamy slag on the particulate emissions from the furnace. The amount of lime added early in the oxygen blowing cycle was reduced, making the slag more viscous and foamy for a six minute period. Instantaneous particulate emissions were monitored throughout the blow by analyzing quencher and venturi scrubber water samples. Particulate emissions were reduced up to 59% during the foamy slag period.IntroductionThe reduction of the amount of waste generated or control of emissions at source is at the top of the ""3R"" hierarchy of waste management (Reduce, Reuse, Recycle). Process and operating practice changes are often the most economical ways to control emissions. At Dofasco, they investigated the effect of operating practice changes, specifically the formation of a foamy slag, on particulate emissions from steelmaking furnaces. They wanted to determine if a foamy slag changed the quantity and nature of the fume evolved from the K-OBM furnace over the oxygen blowing phase.The Basic Oxygen Steelmaking ProcessesThe basic oxygen steelmaking process (BOP) generates large quantities of very fine metal oxide fume during the production of steel. In this process, scrap steel and molten iron (hot metal) from blast furnaces are charged into a steelmaking furnace. Then pure oxygen is injected and a lime flux added . The oxygen reacts with carbon dissolved in the molten iron to form carbon monoxide. Oxygen lances can have secondary nozzles which introduce oxygen above the bath. This secondary oxygen, known as post-combustion, bums some of the carbon monoxide radiating the heat back to the bath. Particulate and gases rich in carbon monoxide are ejected from the furnace during the oxygen blowing phase and are collected by a gas cleaning system. Typically, more than 99.5010 of the particulate is scrubbed from the gases by high energy venturi scrubbers or electrostatic precipitators. The oxide sludge or dust collected may have elevated zinc and lead which is unsuitable for recycle to blast furnaces. Due to the presence of these undesirable elements, treatment and disposal of steelmaking oxide dust is difficult and costly."

Jan 1, 1993

By Desmond M. Levins, Reginald K. Ryan

"Removal of radium from uranium tailings would substantially lessen their environmental impact because it would eliminate, or greatly reduce, the hazards arising from radon emanation, leaching of radium, dust dispersal and gamma radiation. A process is described to extract radium from tailings by leaching in 3M Nael solution. The radium can be rapidly leached at ambient temperatures by either multi-stage contact in agitated vessels or washing on a tailings filter cake. Extraction efficiencies ranging from 80 to 94% have been measured for tailings derived from a number of Australian ores.Methods for radium recovery from the leach solution by precipitation, ion exchange and adsorption have been examined. Precipitation as barium/radium sulphate appears to be the most suitable approach. A possible flow diagram for the process is proposed which involves recycle of the saline leach liquor.IntroductionDisposal of mill tailings is the most contentious environmental issue facing the uranium mining industry. The conventional approach to managing tailings is to store them in a dam above ground. Attempts have been made to stabilize some tailings piles by physical or chemical methods. In a few cases, the tailings have been covered with earth and revegetated. However, most tailings piles from abandoned mills are in a neglected state and subject to the erosive and dispersive forces of nature. The cost of remedial action is high. The United States Department of Energy (DOE) has estimated that it will cost up to $130 million to rehabilitate abandoned mill sites in the U.S .A..Environmental authorities are now insisting that uranium mining companies improve their methods of tailings disposal. In the United States, the preferred approach is burial, either in mines or in specially excavated pits. Tailings retention systems as operated in Canada are regarded as storage facilities until an acceptable method of disposal is found. In Australia, the Fox Commission recommended that tailings from the Ranger project should be returned to the open-cut mine. Returning tailings to the mine has considerable merit, but it is not always a viable option. In many underground operations, it is not physically possible to fit all the tailings in the worked-out mine. In other cases, the groundwater hydrology of the mine may be unfavourable."

Jan 1, 1980