Search Documents

By A. A. Millar

THE output of coal from the Province of Alberta reached its peak; in the year 1928, when 7,334,179 tons were produced. Following this, a steady decline was recorded, and in 1930 a low mark of 4,564, 290 tons was made. Since that time, however, the tendency has been upward, and this year (1937) 5,551,682 tons were produced, compared with 5,696, 375 tons in 1936 and 5,462,973 tons in 1935. The value of the output in 1937 was $14,434,969, against $14, 720,004 in 1936. The coals of Alberta have been classed under three heads, viz., domestic, sub-bituminous, and bituminous The domestic (or lignite) and the sub-bituminous coals are used chiefly for domestic purposes, with the possible exception of the smaller sizes and the output of the two stripping pits at Stereo and Coal Valley The bituminous output is used mainly by the railways, for locomotive purposes, which, in 1937, accounted for 80.6 per? cenr of the total sales of bituminous coal. A fair proportion is sold for stationary engine and steam purposes and, in 1937, 25,000 tons were used in making briquettes at plants operated by the Canmore Coal Company, Limited, and Brazeau Collieries, Limited. The International Coal & Coke Company, Limited, used 99,500 tons in their plant at Coleman, for making coke. The bulk of the 66,000 tons of coke produced was sold for use at the smelter at Trail, B.C.

Jan 1, 1938

By G. H. Charlewood, J. W. McBean

"One hundred years after being developed, the diamond drill is still an essential tool in mineral exploration. The basic principle is unchanged, but the technique has been revolutionized, particularly in the past fifteen years. The cost of core drilling has not kept pace with the rising cost of living. The price of machinery, supplies and labour in drilling has doubled and trebled since 1946. Some of the techniques which have made it possible to hold the price line are described."

Jan 1, 1967

By W C. Shakespeare

The Ontario Committee on Taxation is making a comprehensive study of taxation in the Province of Ontario, and in this connection has received representations concerning mining taxation from a number of interested parties. Some of the more important recommendations on mining taxation are reviewed in this article. Introduction FOLLOWING the appointment of the Federal Royal Commission on Taxation, the Ontario Government, effective in November, 1962, appointed the Ontario Committee on Taxation to review taxes and revenues available to the Province of Ontario and its local governments, to co-operate with the Royal Commission on Taxation and with any other bodies of enquiry appointed by other provincial governments, and to make such recommendations as it sees fit to the Prime Minister of Ontario and the Executive Council. The members of the Committee are: MR. L. J. SMITH, F.C.A., Toronto, (Chairman) MR. ERIC HARDY, Toronto DR. R. CRAIG MCIVOR, F.R.S.C., Hamilton MR. CARL A. POLLOCK, Kitchener MR. R. BREDIN STAPELLS, Q.C., and Toronto. Like its Federal counterpart, the Royal Commission on Taxation, the Ontario Committee has held public hearings, has received written

Jan 1, 1965

By A. G. Doll

The Bond low energy impact (crushing) work index test is specified to be performed on rock specimens between 50 mm and 75 mm in effective diameter. NQ-diameter drill core, frequently used in mineral exploration programs does not meet that specification, it being 45 mm diameter or less. This paper reports the effect of performing the impact test on contiguous sections of HQ diameter and NQ diameter core, exploring the hypothesis that the contiguous intervals give equivalent results in spite of the core diameter difference.

Jan 1, 2012

By Newell G. Alford

COAL companies are definitely becoming conscious of the need for better organization. Mechanized mining and the intricate preparation of coal have brought with them the demand for better trained and more highly skilled mining personnel. Refinement in coal mine management is increasing the demand for young graduate engineers to start in the lower grades of the reorganization and prepare themselves to meet rapidly increasing coal mining responsibilities. The interest is wide in scope and extends from self-helps, extension work, and management study at the mines to stimulation of interest in coal mining amongst undergraduate mining students, leading to their permanent employment after graduation. Data by the United States Bureau of Mines show the total annual value of coal production (bituminous and anthracite in the U.S.) through the past 22 years as being more than 38 per cent of the combined value of all ocher mineral industry products. Natural-gas production has gained rapidly on coal since 1916; petroleum exceeded coal beginning with 1934 (see Figure 1). For this 22-year period, the Committee on Student Interest in Coal Mining, in the A.I.M.E., made a survey of the mining schools in Canada and the United States to show the approximate absorption of young graduate mining engineers by the coal industry. In 1938, 232 mining engineers were graduated as compared with 42 in 1918 (a war year) and 180 in 1923. From 1923 to 1929 the graduates declined to another low of 90, but from there on there was a rapid annual increase in the graduating output, reaching a total of 232 in 1938 and continuing upward to a maximum of over 325 graduating this present month.

Jan 1, 1940

By Ye Chen, Jianhua Chen, Xianhao Long, Qingxia Liu, Zhenghe Xu

"It is crucial to understand the mechanism of the collector interacting with the mineral surface in the presence of water molecules, which could influence the relaxation and electronic properties of sulphide mineral surface due to the proximity effect for narrow band gap of semiconductors. The adsorptions of three typical collector molecules (xanthate, dithiocarbamate and dithiophosphate) on the sulphide mineral surfaces in the absence and presence of water molecule have been simulated by density-functional theory (DFT). The calculated results show that the adsorptions of collectors on clean mineral surface in vacuum are not in agreement with the observed flotation behaviours. The presence of water molecules has a great influence on the adsorption of collectors. The analysis of density of states of the mineral surface atom suggests that the adsorption of water molecules could influence the electronic properties of mineral surface and consequently influence the adsorption between the surface and the collector molecule.INTRODUCTIONIn the separation of multi-metal sulphide ores, the selectivity of a collector is a key factor for the efficient recovery of the aimed mineral. Xanthate, dithiocarbamate (DTC) and dithiophosphate (DTP) are the most common collectors used in the flotation of sulfide minerals. Generally, xanthate exhibits powerful collecting property but lack of selectivity. While dithiophosphate and dithiocarbamate show the good selectivity in the lead and copper sulphide mineral flotation. The mechanisms of these collectors interacting with the sulphide mineral had been attracted many attentions and several mechanism based on experimental results had been reported (Chander & Fuerstenau, 1974; Fuerstenau, 1990; Raju & Forsling, 1991; Crozier, 1991; Bradshaw, Cruywagen & O’Connor, 1995; Guler, Hicyilmaz, Gokagac & Emekci, 2006). However, the micro-mechanisms of the selectivity of these three thiol collectors on different sulphide mineral surfaces are not fully understood."

Jan 1, 2016

By K. J. Palmer, D. A. Silva

"Evaluating resources and reserves requires the reliable modelling of geological domains and their grades. “Multiple point statistics” simulation is a relatively new geostatistical method to generate complex, high-resolution geological models by extracting high-order spatial relations from training images. A method based on combining multiple training images is developed to obtain the correct amount of large-scale continuity and short-scale variability. A calibration process matches the geological spatial variability between the final realizations and the drillhole dataset. A case study with data from the Red Dog mine, Alaska, United States, shows an appropriate reproduction of short-scale variability along boundaries between geological units.RÉSUMÉ L’évaluation des ressources et des réserves exige une modélisation fiable des domaines géologiques et de leur teneur. La simulation par « statistique multipoint » est une méthode géostatistique relativement nouvelle pour générer des modèles géologiques complexes à haute résolution par l’extraction de relations spatiales d’ordre supérieur à partir d’images d’entraînement. Une méthode basée sur la combinaison de multiples images d’entraînement est développée afin d’obtenir la bonne quantité de continuité à grande échelle et de variabilité à petite échelle. Un processus d’étalonnage fait correspondre la variabilité géologique spatiale entre les réalisations finales et l’ensemble des données de forage. Une étude de cas avec des données de la mine Red Dog, Alaska, États-Unis, montre une reproduction adéquate de la variabilité à petite échelle le long des limites entre les unités géologiques."

Jan 1, 2015

By W. M. Goodwin

The gold district of northwestern Quebec, though it has attracted such widespread attention during the past year, is still in the prospect stage throughout, and one must preface any remarks about it with the plain statement that its capacity to produce gold commercially is still subject to proof. However, this proof may be forthcoming any day, and from widely separated localities. Consequently it is of interest to note some of the features of the region and of the prospects now being developed. First I shall note the relation of this mining development to the province of Quebec and to the Dominion; then will follow a brief resume of the known geological facts; and finally I shall describe briefly some of the more advanced prospects developed during the past twelve-month. Those that have followed closely the fortunes of the new gold-field will find little that is new in what follows, but it may serve a useful purpose for others by bringing together scattered items of information and presenting them as a whole. GOLD MINING AND AGRICULTURE First let us consider the gold belt in its relation to the province of Quebec. Apart from the world-renowned asbestos camp south of the St. Lawrence, it is the only mineral development of major importance the province has experienced. It is the first important development in the province's vast area of Precambrian rocks, most of which remains as yet totally unexplored and unprospected. The relative importance of this first mining camp in northern Quebec cannot as yet be gauged, but it is bound to stimulate an active interest in the other mineral-bearing areas now known to exist, and in the vast unexplored spaces.

Jan 1, 1924

By Burns Sutherland

Although some mine hoisting systems incorporating steel wire ropes on drum hoists experience completely dependable performance on the hoist ropes for many years, other rope records illustrate an erratic behaviour pattern and, as such, become a source of concern to the operator. This paper describes the causes of the difficulties most commonly encountered and incorporates methods of providing preventative or corrective maintenance. When such a program is utilized wisely, within the allowable limits of shaft time available, it can be the means of avoiding many unforeseen circum-stances and of reducing operating costs, as well as rope costs, to a mini-mum.

Jan 1, 1970

By L Munholand, G. Soucy, P. Quintal

This work presents early results from the first study to optimize the hydrodynamics of a Plasma Lift Reactor (PLR). The PLR is designed to break down organic contaminants in aqueous solutions. New experimental results are presented for air/water tests and for plasma degradation of organic contaminants in Bayer liquor. In addition, a multiphase Computational Fluid Dynamics (CFD) model has been developed which predicts the hydrodynamic behavior in the PLR. These results of this work suggest the PLR is effective at reducing contaminants in the Bayer liquor and that the CFD model adequately describes the hydrodynamic flow.

Jan 1, 2005

By L. Li

ABSTRACT Stope backfilling is a common operation in many underground mines, which requires a barricade at the base of the stope near the drift entrance to retain the backfill in place. In this paper, the distribution of pore-water pressure in barricades made of waste rock is analyzed. An analytical solution is introduced and applied to estimate the pore-water pressure along the base and full height of the barricade. Results show that the analytical solution generally accurately predicts the distribution of pore-water pressure obtained from the numerical calculations, especially in the upstream part of the barricade, where it is most critical.

Jan 1, 2013

By M. W. Bartley

DURING the field season of 1938, the Ontario Department of Mines assigned a combined geological and geophysical survey patty to the investigation of the location, genesis, structural relationships, and economic possibilities of the hematite deposits at Steeprock lake. The investigation was carried out by detailed mapping of the rock exposures and a magneto-metric survey of the drift-covered portions of the area. This was supplemented during the winter of 1938-39 by further geophysical work conducted on the ice. Dr. A. A. Brant, of the Department of Physics, University of Toronto, was in charge of the geophysical work for the Department of Mines in the summer and for the Sterola Exploration Company in the winter. The writer supervised the geological examination. Scope of the Paper The present paper is an attempt to acquaint the members of the Institute with the structure and mode of occurrence of the deposits, since many people are of the erroneous opinion that they are analogous to the Mesaba and Michigan deposits. It is hoped that, from this discussion, they may be able to draw some conclusions of their own regarding the nature of the deposits, and the importance and future possibilities of the region.

Jan 1, 1939

By C. P. Moore, G. W. Taylor

Vertically dipping lenses of nickel-copper ore at Dumbarton Mines Limited are being mined by a modified blasthole stoping method. The principal access to the mine is provided by a 15-degree decline, which, in conjunction with the use of ramps and declines for secondary access, maximizes the accessibility and mobility of trackless mining equipment. Sublevels are driven in ore on 80-foot vertical intervals and subsequently the ore, ranging in thickness from 15 to 30 feet, is slashed to its limits by a procedure of face sampling and test holing. Two longhole drill jumbos are used to drill off 40-foot vertical slices above and below these levels. Following blasting, the ore falls by gravity to the 500-foot horizon, where it is removed from drawpoints by load-haul-dump units and transported by truck to the main orepass. The rock is crushed to minus 3-4 inches and conveyed to surface by a 30-inch-wide wire rope suspended conveyor. This is achieved in two flights, a lower one of 290 feet and a main flight of 2260 feet. All aspects of the mining operation are discussed in the paper, including ventilation, services and safety.

Jan 1, 1973

By P. R. La Pointe, J. Clark

"Studies have shown that the roof in coal mines is nearly twice as likely to fail at intersections as at entries due to enlarged roof spans, stress redistribution and other factors. However, the relative stability of intersections in a mine varies, and an improved understanding of what factors impact roof instability can lead to efficient, proactive mining practices that both enhance stability and mining efficiency.A study was undertaken at an underground longwall coal mine to develop a model to predict the stability at the intersections of entries and cross-cuts. The statistical analyses relied upon observational and measured data regarding the development of tension cracks, seepage, intersection geometry, mining practices, geological attributes and geomechanical factors at 783 intersections. Each intersection was given a NIOSH roof. Common data mining techniques, such as multivariate linear regression, multinomial logistic regression, decision trees and probabilistic neural nets, were considered and evaluated to establish correlations and associations between stability and the other variables. Two of the more successful techniques were Decision Trees and Multinomial Logistic Regression. The analyses showed that a number of factors impacted stability:• Overburden thickness (impact on stress concentration magnitudes)• Initial opening area (impact on stress concentration magnitudes)• Sulfur content (depositional environment & impact of mechanical properties, leaching effects)• Intersection type (impact on stress concentrations)• Gob distance (impact on stress concentrations)• Presence or proximity of a particular sandstone (impact on mechanical properties)• Roof bolt type and diameter (impact on reinforcement)Some factors showed no statistically significant relation to stability. These included:• Total area• Supported areaSeepage was a more problematic variable in assess. Seepage is associated with instability, but it is not clear whether seepage occurs as a consequence of instability, for example, through the creation of tension cracks, or whether the intersection has been excavated where water already exists and has degraded the rock prior to excavation, leading to greater instability.Seepage appears related to the geology of the roof rock mudstones, not the sandstones. Tension cracks in the intersections occur preferentially where the Sulfur content is below 0.9%. The Sulfur may relate to mechanical differences in the roof rock, and where the Sulfur is low, the roof is less stable, there are more tension cracks, and seepage is greater. This suggests that the weaker mudstones may be more prone the development of tension cracks, not because these rocks are more brittle, but possibly weaker.2-way and 3-way intersections appear to have less seepage than 4-way, although very few intersections overall have any seepage. This is similar to the roof stability, in which the 2-way and 3-way are more stable. 2-way and 3-way intersections have fewer-than-expected tension cracks, while 4-way have more than expected. These results suggest that four-way intersections are weaker and more prone to tension crack development, also suggesting that increased seepage results from weaker roof conditions, rather than the converse. Thus seepage appears to be mostly a consequence of instability rather than a cause and is higher where there are 4-way intersections, mudstone geology and external loading factors like depth of cover and proximity to gob that promotes crack development. The study also indicated that a better understanding of the mudrock facies could reduce uncertainty."

Jan 1, 2015

By F. Chiesa

Forty aluminium A356 castings were poured on a Low Pressure Permanent Mould industrial machine, 500x700mm in platen size. The 152mm wide casting comprised three steps, 25mm, 13mm, 6mm in thickness and a 2.5mm overflow which allowed to assess the thin wall capability of the process. The casting campaign, which produced 40 parts, allowed to test the influence of various production parameters including the time of application of the pressure in the crucible, artificial cooling of the mould and casting rate. The thermal history in the mould was recorded over the 40 cycles, which allowed to construct a reliable thermal model of the mould/casting assembly. The metallurgical quality of castings representative of the various conditions was assessed in the 25mm, 13mm and 6mm plates. This included measuring the level of microporosity, the dendrite fineness (DAS), along with the tensile properties in the T6 condition. The radiographic quality per ASTM E155 was also determined. Modelling filling and solidification allowed to verify the validity of the predictions based on available relationships relating microporosity, secondary dendrite arm spacing (DAS) and local tensile properties (Quality Index, Q) to the local thermal solidification parameters.

Jan 1, 2007

By D. Bernard

Over the last decades, the wrought aluminum casting industry has made significant progress with regards to process consistency by the introduction of new technologies in the field of liquid metal processing and casting. These technologies, combined with the application of best practices, have led to increases in productivity as well as better process performances and product quality. The competition in the addedvalue aluminum products (by opposition to P1020 production) is, however, very strong and involves players that did not hold a major role five years ago but who are now exerting a strong competitive pressure on our industry even sometimes from far abroad. There are still technical and technological challenges remaining in the different areas of aluminum casting production, amongst which metal pre-treatment, furnace operations, in-line treatment and casting hold a predominant influence. The comprehension of the contribution of each individual process step to the entire process chain is a key element and must be considered in future process optimisations. This paper presents the technological position of the casting industry and tries to highlight areas where further progress can be made.

Jan 1, 2006

By C. H. Knight

"THE OBSERVATIONS that follow are confined to simple wet cyclones such as the cylindro-conical unit developed by the Dutch States Mines and marketed in America under the trademark 'Dorr-Clone'. Energy to do the work comes from the inlet velocity of the feed slurry, which is usually pumped' to the unit by a centrifugal pump.Such cyclones are simply classifiers of enormous capacity and depend for their separating effect on differences in rates of particle settlement. These particle settling rates, of course, vary with particle size, particle density, particle shape, pulp viscosity, and pulp density.The dilution of the overflow product affects both pulp viscosity and pulp density. In most operations, the temperature and the composition of the liquid -hence its viscosity --are fixed, but both pulp viscosity and pulp density can be changed by changing pulp dilution.Since the separating effect depends on differences in rates of particle setting, a perfect split with 100 per cent of the particles coarser than a given size in the underflow and 100 per cent of the finer sizes in the overflow is not possible. Just how far the separation departs from this perfection can be calculated rather exactly from the following principles, which also apply to mechanical classifiers. In removing or settling out of the overflow product all particles up to a specified size, some of the finer particles must settle out simultaneously."

Jan 1, 1955

By T. Krumins, F. C. Ruff, M. Eichhorn, L. Zunti

Hatch Ltd. has recently completed a project to increase refractory gold ore processing capacity at Newmont Mining Corporation’s Twin Creeks facility. The objective of the project was to increase throughput by approximately 10% by adding a third autoclave feed pump to each of the two autoclave circuits. To minimize project capital cost, autoclave feed pumps from Newmont’s decommissioned Lone Tree facility were evaluated and found to be suitable for this new service. The existing pressure oxidation circuit was reviewed in a debottlenecking study to determine other upgrades required to facilitate the increased throughput. Interruption to operations was minimized with a detailed construction plan, supplemented with detailed 3D layout model sequencing studies. The focus of this paper is project development, multi-discipline design considerations, and implementation results.

Jan 1, 2014

By Xiang Li, Xibing Li

It is paramount that the stability of rock slopes be correctly accounted for under diverse operating and environmental conditions. Owing to different sources of uncertainty entailed in such stability problems, conventional deterministic approach through the calculation of a factor of safety (FOS) cannot reflect quantified uncertainties explicitly and sufficiently. Thus it is highly desirable to invoke the reliability approach to consider uncertainties in a systematic manner. Nowadays, the current design standards have an increasing tendency to ensure rock slope stability by pre-defining a target reliability index (or target probability of failure), viz., the reliability level of a rock slope is pre-set as a target to be satisfied. In such a situation and considering the fact that the FOS used as an indicator of slope performance still has a very wide acceptance, we focus on proposing an inverse-reliability-based methodology which aims at developing a two-fold indicator strategy, i.e., using the FOS and reliability together to deal with slope stability problems. The basic idea behind it is to utilize a so-called inverse first-order reliability method (IFORM) to directly calibrate the FOS provided the target reliability index has been given. In this way, the calibration scheme relating the FOS can be rationally done by not only incorporating uncertainties, but also satisfying a desired level of the prescribed reliability. Based on this, to make the IFORM computationally feasible and also reduce its computational cost, we introduce the response surface method (RSM) to generate a surrogate for the FOS-based limit state function (LSF), considering the lengthy and complicated form of the FOS in some recognized methods (e.g., within the framework of limit equilibrium). Distinguished from the existing RSMs that potential inadequacies may arise, we present an RSM based on a hybrid approach combining support vector machine (SVM; used as a regression technique) and uniform design (UD; pertaining to experimental design). Using a representative example of rock slope stability problem, we demonstrate the feasibility and validity of the developed methodology, during which the associated sensitivity study and further discussion are also performed. By dint of such a methodology, we can establish a link between the conventional deterministic approach and the reliability approach, where a logical and realistic framework is provided, for cases achieving the specified reliability, to assist in selecting the FOS which remains adequate for rock slope stability even in the face of uncertainty.

Jan 1, 2015

By A. O. Dufresne

A Step which, it is believed, will prove extremely beneficial to the Quebec asbestos-mining industry was taken during 1931, when the asbestos mine operators of the Province assembled to work out a uniform method of naming the products of their mines. The outcome of several meetings was the drawing-up of a classification which defined, limited, and designated anew the numerous grades of asbestos marketed. It entailed no drastic departure from the existing processes of grading, nor any revolutionary changes in methods of testing, but aimed rather to perfect existing methods. The classification proposed has been accepted by all operators in the Province, who, from January first of this year, began introducing the new nomenclature. Unless one is conversant with the properties and mode of occurrence of chrysotile asbestos, with the unique milling methods devised for its recovery, and with the history of the development of their technique, he may not readily understand the basis of the new classification. For information on these and other data concerning the industry, the reader is referred to a recent publication, Chrysotile Asbestos in (Canada, by James Gordon Ross, issued by the Mines. Branch of the Department of Mines, Ottawa. The object of this paper is to present briefly some of the phases in the evolution of the classification of Canadian chrysotile asbestos, in the hope that the recent effort to standardize the marketable products of one of Canada's most important non-metallic mineral industries will open a field for discussion, fruitful in new ideas and constructive suggestions. The necessity for the grading of asbestos results fundamentally from the fact that the price per ton depends on the length of fibre. At all times in the history of the industry, the very limited available supply of the longer grades, as well as the requirements of the trade, have caused relatively very high prices to be paid for fibre over half an inch in length, while for the shorter grades the price decreases rapidly, and at a rate which bears no proportionate relation to the length of fibre.

Jan 1, 1932