Search Documents

By G. H. McKay

AT the Eagle mine, near Gilman, Colorado, where the Empire Zinc Company have installed an underground mill, transportation problems were comparatively simple. A railway siding on the Denver and Rio Grande railway is equipped with an unloading dock or platform at the portal of their service incline adit to the mill. This 18-degree incline is approximately 600 feet long from the unloading track to the head of the mill skipway. For the Big Missouri mill, upwards of 2,500 tons of material and equipment had to be trucked from tidewater at Stewart, B.C., a distance of 21 miles to the Big Missouri camp at elevation 2,800. From that point, this freight had to be moved either over or through the Big Missouri ridge, rising to elevation 3,450, to its final location 800 feet from the surface between elevations 2,150 and 2,350. Immediately after leaving the government dock at Stewart, the road crosses the International boundary line into Hyder, Alaska, and then follows a water grade for eleven miles along the lower stretches of the Salmon river. leaving the river, the road climbs for two miles before crossing back into British Columbia territory at Silver Heights, and then continues for another mile and a half to where the Big Missouri road branches off from the main road to the Premier mine. For a distance of four miles from the junction of the roads, the Missouri road is very narrow, with many sharp curves and with irregular up and down pitches and grades up to 25 per cent until it reaches the Summit. From there on, a fairly easy grade leads a mile and a half to the end of the road on Joker Plats. In winter, the last stretch of road is subject to heavy snow drifting, especially through a narrow funnel-shaped gulch, known as 'The Gap', where the snow may pile up to a depth of over twenty feet.

Jan 1, 1938

By A. Gauthier, J .. E. Muir, M. Cormier

Falconbridge's Lac Shortt gold deposit is located in Gand Township, some 25 km north-east of Desmaraisville, The deposit was outlined in i980 by a drilling program me conducted by Falconbridge Ltd. in a joint venture with Corporation Falconbridge Copper after three years of systematic exploration by Falconbridge Ltd. in the Desmaraisville area. The gold bearing structure had previously been drilled by three other exploration companies. As based on an underground development programme conducted by Corporation Falconbridge Copper, the "in-si tu" mineral inventory to a depth of 500 metres at a cut-off grade of 3.0 g/t is estimated at 1 937 605 tonnes at a grade of 6.4 g/t (uncut) and 6.0 g/t (cut). Regionally, the stratigraphy consists of thick sequences of volcanic and volcanosedimentary rocks intruded by numerous and voluminous mafic (gabbro), felsic (granodiorite, syenite) and anorthositic intrusions. Structurally, at least two fold sets and one major fault system (E-NE) are present. Minor fault systems oriented E-NE and N-NW also occur. Mine stratigraphy can be divided into 1) - the hangingwall; 2) - ore zone; 3) - footwall. Hanging wall rocks include: a) green lapilli and blocky tuff b) transition zone c) green mica crystal tuff and d) red dolomitic tuff. Ore zone rocks include: a) bleached mafic tuff b) barren carbonates, c) pyritic dolomitic tuff (?) and d) brick-red syenite. Footwall rocks include: a) magnetic lava (so-called diorite), b) mafic lapilli and blocky tuff and c) alkali basalt, Native gold is the only gold mineral so far identified and it occurs both as free grains in gangue and as micro-inclusions in pyrite. Two geochemical groups were identified in the main rock units: 1) Alkali-rich rocks cons is ting of the ore zone and foot wall rocks and 2) Subalkaline group consisting of the hanging wall rocks. Ore analysis also shows Ba, Sr, W, Zr, REE and F enrichment in the ore zone. Footwall rocks are enriched in Na20. Present geological and geochemical data do not permit a clear interpretation of the formation for the Lac Shortt gold deposit but suggest it is a volcanic-hosted stratabound type. The bulk of the mineralization is associated with an exhalative phase following alkalic, carbonic, hydrothermal activity and part of the mineralization is associated with a late intrusive phase.

Jan 1, 1984

By Paul B. Warrington

This paper presents a discussion of the factors affecting copper scrap markets, including such items as price levels, freight. grades of material, sources and packaging. Reference will also be made to the effective life and turn-around of the copper content of some products. Introduction IN TERMS OF SIZE, copper scrap is second only to ferrous scrap in tonnage recycled. However, in total value, it is second to none. For example, world scrap recovery during the preceding 4 years averaged just under 2,300,000 metric tons per annum, and at an average price of 70 ¢ a pound, this works out at a turnover of about $3.5 billion, which indicates that the copper scrap industry, or recycling as it is now becoming known , is a substantial one.

Jan 1, 1977

By Derek V. Ellis, Jack L. Littlepage

"Marine ecosystem effects ar1smg from the discharge of man-generated wastes to the sea can be schematized as: acute poisoning, chronic poisoning, enrichment, suffocation, temperature effects, salinity effects, toxin bio-concentration, changed production rates and changed species equilibria. A professionally designed site-specific monitoring program to check for such effects can not only safeguard the marine ecosystem from degradation, but it can also protect the industry involved from unanticipated remedial action after expensive construction has been undertaken. Monitoring programs should consist of three steps. Step 1 is an ecosystem survey which should be undertaken prior to final design of the discharge system and submission of applications for permission to discharge, because there can be considerable cost savings in obtaining information at an early stage in development. Step 2 involves location of the effluent field at the time of starting discharge, and analysing its dispersal behaviour. Step 3 consists of ecosystem monitoring with sampling stations and specific tests based on the accumulated prior information."

Jan 1, 1972

By J. R. Kadambi, J. Furlan, Kucukal E.

"Hydrocyclones are used in various industrial applications, including mineral processing and tailings management, to separate or classify solid particles and/or liquid droplets from multiphase feed. The fluid flow in a hydrocyclone (used in mineral processing) was investigated numerically and experimentally using particle-image velocimetry (PIV) and refractive index matching techniques. Two turbulence models were used in the calculations: the k–? model and the Reynolds stress model. Particle image velocimetry measurements were taken at various spatial locations along the cyclone. Computational results were validated globally using pressure and flow-rate readings at the boundaries, and locally by comparing the PIV velocity-vector maps and profiles.RÉSUMÉ On utilise les hydrocyclones dans diverses applications industrielles, dont la minéralurgie et la gestion des résidus, pour séparer les particules solides et/ou les gouttelettes liquides de l’alimentation polyphasée, ou pour les classifier. Une étude numérique et expérimentale sur l’écoulement des fluides dans un hydrocyclone (dont on se sert en minéralurgie) a été menée à l’aide des techniques de vélocimétrie par images de particules (PIV, de l’anglais particle image velocimetry) et d’appariement des indices de réfraction. Deux modèles de turbulence ont été utilisés dans ces calculs, à savoir le modèle de turbulence k–? et le modèle aux tensions de Reynolds (RSM, de l’anglais Reynolds stress model). La valeur de la PIV a été mesurée à diverses positions spatiales le long du cyclone. Les résultats de ces calculs ont été validés globalement à l’aide de relevés des pressions et du coefficient d’écoulement d’une extrémité à l’autre de l’hydrocyclone, et localement à des coordonnées spatiales spécifiques en comparant les cartes et les profils du vecteur vitesse PIV.INTRODUCTIONA hydrocyclone is a piece of equipment used to separate and/or classify solid particles or liquid droplets from liquid solid or liquid-liquid feed. Versatile in application, hydrocyclones have been widely used in industrial applications including the food, oil, power generation, chemical, and mineral processing industries. The first hydrocyclone was introduced in 1891 by Bretney to purify various liquids (Bretney, 1891). Hydrocyclones have a relatively simple design with no moving parts, which leads to an efficient separation process."

Jan 1, 2017

By T. R. Ellis

The valuation of mineral properties in the U.S. is only partially regulated. The regulations which have jurisdiction or impact appear to have such mainly as a consequence of unintended fallout, since the regulations were designed for other purposes. Court case history can also be important. The combined results are a mixture of bad and good, with important lessons to be learned. Since 1981, the Securities and Exchange Commission has prohibited U.S. listed companies from reporting quantitative estimates of mineralization and the value of mineralization, other than proven and probable reserves. This results in the minerals appraiser (valuator) working with a shortage of data in his everyday work, both on the subject property and in sales analysis. Between 1989 and 1995, all 50 states and essentially all federal agencies adopted the Uniform Standards of Professional Appraisal Practice (USPAP) for real property appraisals (valuations). The major national appraisal societies also require their members to abide by USPAP. A significant portion of minerals appraisals must now follow these standards. This paper will discuss the content of USPAP. It provides a very good framework for the valuation of a minerals property or a mine, both as real property and as a business. However, the credentialing standards for real property appraisers are now prohibitive for minerals appraisers.

Mar 1, 2002

By T. R. Ellis

"The valuation of mineral properties in the U.S. is only partially regulated. The regulations which have jurisdiction or impact appear to have such mainly as a consequence of unintended fallout, since the regulations were designed for other purposes. Court case history can also be important. The combined results are a mixture of bad and good, with important lessons to be learned.Since 1981, the Securities and ExchangeCommission has prohibited U.S. listed companies from reporting quantitative estimates of mineralization and the value of mineralization, other than proven and probable reserves. This results in the minerals appraiser (valuator) working with a shortage of data in his everyday work, both on the subject property and in sales analysis.Between 1989 and 1995, all 50 states and essentially all federal agencies adopted the Uniform Standards of Professional Appraisal Practice (USPAP) for real property appraisals (valuations). The major national appraisal societies also require their members to abide by USPAP. A significant portion of minerals appraisals must now follow these standards. This paper will discuss the content of USPAP. It provides a very good framework for the valuation of a minerals property or a mine, both as real property and as a business. However, the credentialing standards for real property appraisers are now prohibitive for minerals appraisers."

Jan 1, 2002

By M. H. Rana

"A survey of our knowledge in the field of rock mechanics is presented from the viewpoint of applications in the mining industry. Aspects of rock mechanics of special interest to the industry are enlarged upon, with emphasis on the avoidance of over-generalization. The relationship between fundamental and practical rock mechanics is discussed, and the need for cooperation between the university and industry to further our knowledge of -useful rock mechanics is emphasized. An attempt has been made to establish the scope of rock mechanics, as applied to problems in the mining industry. This is brought about by projecting rock mechanics as a tool to be intelligently used rather than magic, capable of producing ""miracles."" Continued education is important for individuals engaged in the application 0f rock mechanics in the mining industry. The scope of this education is discussed from a viewpoint of better communication between industry and the education and/or re-search establishments engaged in this work.Finally, the dangers of over-emphasis on rock mechanics are mentioned, but a justification of the in-vestment in rock mechanics programs in mines is also presented."

Jan 1, 1966

By G. W. Evatt

This paper presents the scientific framework underpinning the Resource Valuation and Optimisation Model (RVOM). The RVOM is a Real Options software package, which helps mine owners optimally plan their operations, understand their project risks, and make defensible valuations. This is achieved in the presence of both financial and physical uncertainty. The three key outputs from the RVOM are: Valuation, Optimal Decision and Probability of Decision, where a decision can include any combination of: normal operation, expanded operation, care and maintenance, and abandonment (and variants thereof). This paper presents a clear example of the RVOMs usage to a case-study gold mine.

Jan 1, 2011

By E. Michelotti, M. Cardu

This paper presents the results of a new method that has been tested to recover metallic cobalt lost by diamond beads from rock cuttings. When dimension stones are cut using diamond wire saws, the beads become worn and, before the end of their cycle life, lose a certain amount of material; this material is prevalently made up of sintered metal and diamonds. The material is then washed away, together with rock debris, in a dilute pulp. In effect, this process involves the dispersion of economically valuable, but potentially polluting, materials (such as cobalt) that are used to confer indispensable technological features to the beads. This current research aims to develop a waste-processing pilot plant (High-gradient Magnetic Separator or HGMS) to recover metallic components from the pulp by means of a suitable separation. The research\u2019s purposes are two-fold: a. to remove the polluting components from the rock debris before their disposal and b. to start a recycling process of the valuable metals.

Jan 1, 2010

By J. Visman

"SummaryThis paper is presented as part of a programme to show the steps taken by industry and others interested in supplying a solid fuel of constant quality to 'satisfy a consuming market. The paper deals with the general principles underlying quality control in coal preparation plants, namely, constant quality and close adherance to acceptance limits. It also describes how control of ash content is ""generally hampered by the problem of coal sampling .and the long duration of the ash analysis and how these difficulties may be overcome.Quality control can be effected in several ways. Thorough blending wll reduce variations appreciably, except those of long trend. The latter can be detected by automatic sampling and quick ash analysis. At present, under favourable conditions, a system of half-hourly ash determinations with an accuracy of 0.5 to 1.0 per cent can be realized, to the effect that trends with a 'wave length' of more than two hours cu be eliminated within the limits of accuracy of the ash figures. The general solution of the problem is a combination of blending, accurate sampling, quick ash determination, and statistical analysis of the pattern of ash distribution.The use of statistical methods of analysis, such as the t test and F test, is •discussed at some length in order to emphasize the importance of the correct evaluation of observational data if there is to be confidence in the validity of test results.General ConsiderationsCOAL, as a fuel, is too cheap for a long haul across the country. The limiting distance depends on the price of the local competitive fuels, and, as the price depends to a great extent on quality, so does quality, to the same extent, command the market."

Jan 1, 1952

By I. Le May

"The assessment of integrity in plants is discussed, together with the codes that are being developed for in service evaluation of engineering fitness for service. The use of Risk Based Inspection is described and some examples are provided of the evaluation of in service components in which flaws have been detected. An example of the assessment of the structure of a mine processing facility is described, and application of Risk Based Inspection and plant assessment procedures to mines is discussed. Periodic assessment of large plants and components to determine their integrity for continued safe operation is becoming a more accepted approach than formerly when regular shutdowns were the normal practice. This is on the way to becoming the preferred procedure for petrochemical plants and power generating plants, and the same philosophy is appropriate for many mining operations. Both the American Petroleum Institute (API) and the American Society of Mechanical Engineers (ASME) have committees developing codes for the continued operation of equipment as distinct from the existing design codes. The philosophy is one of risk-based inspection, which can be on a purely qualitative basis or more quantitatively based.The purpose is to reduce the inspection of unnecessary and non-critical items and to concentrate on the most critical components, reducing costs and downtime and increasing safety. The approach differs from that considered by many maintenance engineers, in that defects that are identified during an integrity evaluation do not automatically cause a component or structure to be condemned or require that repairs are made right away. The seriousness of the defect must be considered and the safe operating life can be estimated before it becomes necessary to replace or repair the unit or component. This is no different from what is done today with passenger aircraft and, to an increasing extent, with pressure vessels, reactor vessels and similar components in the petrochemical and power generating industries."

Jan 1, 1998

By E. LaRocque

Denison Mines Limited has been processing uranium ore in the Elliot Lake area for the past 20 years. As the original concept of uranium processing has been modified somewhat over this period, the present paper will describe the current recovery practices at the Denison mill from crushing through concentrate drying and packing . Special emphasis will be placed on the leaching, ion exchange and precipitation sections of the process, with consideration being given to the entire circuit. Descriptions will be given of equipment now being used and control strategies will be discussed.

Jan 1, 1979

By F. Habashi

Lead is an ancient metal, has been produced to-date from its ores exclusively by pyrometallurgical route. The process suffers from high operating cost and excessive pollution problems. Extensive research has been going on since the beginning of the twentieth century to find a non-polluting process for its production and a solution for its complex refining scheme. It has been assumed correctly that the hydrometallurgical route should be the most promising. Pilot plants have been constructed and operated for a reasonable periods, but no process has proved to be satisfactory. As a result, a number of smelters and refineries have been shut down. The present review analyses the situation and suggests that the best route to treat lead sulfide concentrates is by leaching with fluoroboric acid, HBF4, containing ferric fluoroborate, Fe(BF4)3, and electrolyzing the solution in a diaphragm cell - - a process recently invented by Italian metallurgists. In this process, any silver present in the concentrate remains in the residue together with elemental sulfur and can be recovered by known methods.

Jan 1, 2008

By Y. Nara, N. Aramaki, M. Maruyama

Evaluation of three dimensionally non-uniform strain distribution in rocks under various conditions such as in water or under freeze-thaw cycles is of significant importance to understand their complex deformations and fracturing mechanisms. For this purpose, we developed an image analysis method which can evaluate or “measure” the three dimensional (3-D) strain distribution in rocks. The proposed method utilizes the 3-D images of rock under initial and deformed configurations, which are obtained by some imaging techniques such as X-ray computed tomography (X-rayCT). In the proposed method, the obtained 3-D images are divided into multiple sub-regions of interest. For each sub-region, the strain is evaluated utilizing 3-D affine transform with unknown coefficients to be determined. In the first step, 3-D voxel level displacements at multiple representative points in each sub-region are computed by 3- D digital volume correlation technique between the comparison images and the initial-guess of the transform coefficients are obtained. In the second step, referring to the initial-guess of unknown transform coefficient, they were optimized in sub-voxel level by finding optimum digital volume correlation between the comparison images, which can evaluate the transform coefficients with higher precision. From the calculated transform coefficients, the strain was directly obtained through the spatial derivative of displacement based on affine transform. In this paper, along with the description of the proposed method, the evaluation of deformation in a lignite specimen due to immersion in water was presented as an application example. As the 3-D imaging technique, micro-focus X-rayCT was applied. The result showed that the induced dilatational strain field due to the initiation and extension of cracks in the specimen was clearly captured. Therefore, authors believe that the proposed method can be applicable to various problems in rock mechanics.

Jan 1, 2015

By P. Trudel, M. A. . Cloutier

This lithogeochemical study demonstrates that the Gilman and Blondeau Formations in the Chibougamau area belong to a subalkaline suite of tholeiitic affinity poor in potassium. The Gilman Formation is composed mostly of basalts, with subordinate andesites and rare dacites, while the Blondeau Formation comprises all lithologies of the basalt-andesite-dacite-rhyodacite-rhyolite ensemble. Both AFM and Harker variation diagrams show that all these rocks originated by differentiation from the same magma reservoir, and are related to one volcanic episode, This study did not, however, identify hydrothermal alteration zones useful for regional geochemical prospect ion.

Jan 1, 1984

By John R. Hayes, Kebbi A. Hughes, John Rowson, Peter E. R. Blanchard, Jeremiah C. Beam, Andrew P. Grosvenor, Arthur Situm

Uranium ore bodies contain elements within mineral phases that need to be disposed of responsibly. Solid waste can be placed in a tailings management facility (TMF) to contain the waste elements and limit interactions with the environment. It is important to understand how the chemistry of the tailings evolves throughout the lifetime of the operations that feed the TMF and after the site has been decommissioned. The objective of our collaboration with Orano Canada was to study how the tailings from the TMF located at McClean Lake, Saskatchewan change over time. This manuscript discusses our use of X-ray absorption spectroscopy (XAS) and X-ray microprobe to study the fate of Mo and Ca in the tailings. Mo is considered an element of concern (EOC) and it is necessary to determine if a stable solid Mo-bearing species forms. Thermodynamic modeling suggested that aqueous Mo would precipitate over time as powellite (CaMoO4). Comparing Mo K-edge XAS spectra from the solid tailings to the aqueous Mo concentration in the pore water showed that powellite did form and that this did result in a decrease in the aqueous Mo concentration over time. Further, it has been proposed that Ca2+(aq) can react with bicarbonate ions in the pore water and precipitate as calcium carbonate (e.g., CaCO3). This reaction would limit the aqueous bicarbonate present in the tailings that could react with uranyl ions to form soluble uranyl-carbonate complexes. We have identified several trace Ca-bearing species, including carbonates, in the tailings using XAS and X-ray microprobe.

Jan 1, 2020

By The Mill Staff

Introduction The Hollinger cyanidation mill commenced operating in June, 1912, and 49,779,978 tons of solids had been discarded by the end of 1950. The present tailing disposal plant has been in operation since 1924 and holds 39,762,250 tons. The tailing disposal plant is on the property of Kayorum Gold Mines, Limited, about a mile and a quarter south of the mill. The area available for tailing covers 640 acres and is roughly l ¼ miles long by ¾ mile wide. Tailing was first deposited on the McKay veteran claims, l mile long by 1/2 mile wide, which were later included in the Kayorum property. This site sloped from northeast to southwest, the slope amounting to 106 feet between the northeast corner and the low land to the southwest. The low land was wet and a considerable area was covered with muskeg up to 17 feet deep. It was drained by a brook running across the property in a southwesterly direction. Later, when more ground was needed, the low-lying mining claims adjacent to the south and west boundaries were acquired to allow for the extension of the plant. This entailed some extra difficulties and expense that would not have been encountered had the whole of the present site been acquired with the original purchase. At the present time, the top of the tailing deposit stands at two elevations, but eventually the tailing deposited on the extension to the original plant will be raised to the same height as the older deposit. Previous to 1924, all of the tailing was deposited on Low land and in lakes near the mil1. Between 1924 and 1926 an increasing tonnage was sent to the McKay claims until, in 1926, all of it was being sent there. In 1936, the area of the deposit was extended and shortly afterwards all of the tailing was deposited on the new site.

Jan 1, 1951

Why A Friction Hoist? B EFORE discussing the equipment, it would be instructive to review the factors that influenced the management of Opemiska Cop-per Mines to purchase a friction hoist rather than a conventional double drum hoist. The mine required that 250 tons per hour be hoisted from a depth of 2,100 feet. They also specified that the top speed should not exceed 1800 feet per minute. Eight ton capacity skips in balance and a maxi-mum hoisting speed of 1725 feet per minute would meet the required <Output on a duty cycle as follows: Loading time Creep away from loading pocket Accelerate (at 2.5 ft/sec2) 10 seconds 5 seconds 11.5 seconds Full speed run Decelerate (at 2.5 ft/sec2) Creep into dump Cycle time Trips per hour Tons per hour 72 seconds 11.5 seconds 5 seconds 115 seconds 31 31x8 = 248

Jan 1, 1962

By F. J. Guevara

A two-dimensional mathematical model for fluid flow and heat transfer in a sixin- line electric smelting furnace was developed to study the effects of temperature on slag viscosity in both the liquid and mushy zones. The model focused on the fluid dynamics of the molten slag and the effects on the formation of a slag freeze layer on the hot face of the furnace wall. Previous experimental and mathematical work, carried out under Ra number of 109 and using a fluid with Pr number of 65, showed that it is possible to mathematically describe the freeze layer formation over a vertical wall using a fixed-grid model. The chemical composition of the slag was taken into account through its effect on the viscous activation energy as well the solidus and liquidus temperatures. The results show that the flow pattern is strongly modified in areas of high viscosity, in front of the cooling system and at the slag-matte and slag-calcine interfaces. The results are discussed in terms of heat flux over the refractories and their effects on cooling system design.

Jan 1, 2007