Search Documents

By Walter Greaves

THIS paper describes a series of tests performed at the Hollinger mill during the past four years, in which both metal and rubber-lined pumps were used for pumping sand and slime. While conditions will not be the same at other mills, it is felt that the information gained from the tests should be of value to other operators and of assistance to them in selecting the most efficient size of pump and kind of lining for economical operation. For the successful operation of pumps with rubber linings there are certain conditions, which, if recognized at the outset, will save the operator a good deal of work and trouble. First is the necessity of keeping sharp pieces of steel, or anything that might cut the lining, out of the pumps. This can be effected by placing screens in the proper locations. Second is to recognize the fact that the rubber lining of the shell, and the rubber cover of the impeller, are subjected to very different conditions. The shell lining, :being at rest and well supported by the metal case, has a relatively easy job compared ? with the impeller covering, which is subjected to centrifugal force and has a tendency to tear itself away from the metal core. Also, the pulp travels through and past the impeller at a high velocity. These two factors, centrifugal force and velocity of the pulp, would appear to set a limit to the speed at which, for a given set of conditions, it is economical to run a rubber-covered impeller. Therefore, a pump should be large enough for the work to be done. To get the best mechanical efficiency, it must be operated somewhere near the limit of its capacity, but this may not give the best overall cost, because the saving in power, due to the high efficiency, may easily be lost through excessive wear on the lining. It would appear that this condition is more critical in a rubber-lined pump than in one lined with metal.

Jan 1, 1939

By A. S. Romaniuk

More than a decade ago, CANMET management recognized the need to make better use of existing technological information in mining and extractive metallurgy-two fields basic to the economic well-being of Canada. There were at that time no indexes or files dedicated to disseminating technical information for the many minerals mined and processed in Canada, including coal. CANMET, with the nation's largest research and library resources in the minerals field, was in a unique position to fill this need. Initial efforts were concentrated on building a mining file, beginning with identification of world sources of published information, development of a special thesaurus of terms for language control and adoption of a manual indexing/retrieval system. By early 1973, this file held 8,300 references, with source, abstract and keywords given for each reference. In mid-1973, operations were computerized. Software for indexing and retrieval by batch mode was written by CANMET staff to utilize the hardware facilities of EMR's Computer Science Centre. The resulting MINTEC file-one of the few files of technological information produced in Canada-is the basis for the national literature search service in mining offered by CANMET. Attention is now focussed on building a sister-file in extractive metallurgy using the system already developed. Published information sources have been identified and a thesaurus of terms is being compiled and tested. The software developed for CANMET's file-building operations has several features, including the selective dissemination of information and production from magnetic tape of photo ready copy for publication, as in a bi-monthly abstracts journal.

Jan 1, 1979

By Guangdong Institute of Resources Comprehensive Utilization, Y. H. Tang, H. X. Hu, T. S. Dong, Z. H. Zhang

"A world class rare metals ore deposit in Africa belongs to a massive granite type poly-metallic pyrochlore-niobium resource. Successful project development in realizing the resource is vital to Africa’s economy and pyrochlore processing technology.The ore properties are quite complex due to the presence of varieties of valuable minerals, fine dissemination and intimate association of minerals and the relative abundance of easy-floatable minerals. The separation of pyrochlore from zircon, calcite and mica is generally considered difficult. Whilst studies have previously been conducted by several independent institutions overseas, no satisfactory process has yet been developed to date for the ore deposit—possibly due to the process designed being too complex; high cost of regents; lower performance.Based on process mineralogy study and extensive testwork, the authors have in recent years developed a new technology—“De-slime—Iron-rejection—Zircon (with calcite) and Calcite reverse flotation—Pyrochlore flotation”. The flow-sheet is characterized by ?1prior removal of slimes and iron minerals; ?2 Zircon (with calcite) and Calcite reverse flotation; and ?3Pyrochlore flotation applying new type of chelating collector GYX3 developed by GZRINM in conjunction with selected regulators and depressants.The process involved in the new technology is simple to implement and facilitates stable operation; the flotation reagent regime is easily adaptable; the cost of main reagent is lower largely because it is easy to manufacture and is environmental friendly. Laboratory test results demonstrated that, for raw ore assaying 0.35% Nb2O5, 0.03% Ta2O5 and 0.45% ZrO2, pyrochlore concentrate grade of >35% Nb2O5 could be obtained with >74% recovery. Meanwhile, the Ta2O5 content in pyrochlore concentrate could be recycled, and ZrO2 recovery >50% could be achieved in zircon concentrate assaying ZrO2>63%—significantly improving the technical-economic indicator. These results were verified in pilot trials of 1.44t/d throughput. The paper presents the new technology in whole, summarizes the key factors affecting its performance and discusses in simple terms the mechanism of separation."

Jan 1, 2016

By M. Girard, C. Farsangi, N. Singh

"Canadian Royalties Inc. owns and exploits the Nunavik Nickel Project: a copper and nickel deposit in Nunavik, Québec. The nickel and copper concentrates are filtered by plate and frame filter presses, and are transported 100km north to Deception Bay by truck. As the site is situated in the far north, extreme weather can be detrimental to production: roads can close for significant periods of time, resulting in the concentrator using all its storage capacity. During the winter of 2017, this accounted for over 100 hours of unplanned mill downtime. Different solutions to this problem were evaluated and the most economically viable combination of solutions was determined to be the use of concentrate storage containers and upgrading the plate size of the existing nickel filter press. By satisfying new, increased utility requirements, the cycle times would not change, but produce 30% more filter cake. Simulations were developed to determine the number of concentrate containers needed in conjunction with the upgraded press to eliminate unplanned downtime due to road closures and secure production through the winter. This paper summarises these simulations, the commissioning and start-up of the upgraded filter press, container loading procedures, and how this was put together to achieve a record 2018 winter season with a 90 percent reduction in downtime. The payback period of the project was 4 months. A specialised side-tipping trailer emptied the containers during the fall of 2018.INTRODUCTION The Nunavik Nickel Project is a nickel/copper mining project located in Nunavik, Québec. The nickel and copper concentrates are stored in stock tanks after thickening and are then filtered by plate and frame filter presses at the concentrator before being transported 100km to the shipping port at Deception Bay by trucks. The region is prone to periods of extreme weather during the winter, with winds that can reach +100km/hr and blizzards that severely limit visibility. The roads to Deception Bay are often affected by this weather, causing closures that last an average of 18hrs and as long as 72hrs. Additionally, there is a 15% chance that road closures occur within 24hrs of the last event. This has been an issue for the concentrator team since start-up in 2013, causing unplanned mill downtime every winter (Table 1) due to filling concentrate storage capacity during prolonged closures of the roads to Deception Bay."

Jan 1, 2019

By D. -A Tremblay

Dynamic wetting spread factors and interfacial heat transfer coefficients were determined for aluminum droplets solidifying on copper substrates, The spread factors were determined from the droplet geometries while the heat transfer coefficients were obtained by solving inverse heat conduction problems, 1-D and 2-D heat transfer models are presented and the results they provided are compared, For the latter, a sensitivity analysis was also performed to determine the influence of thermophysical properties and boundary conditions. Experiments were alternatively carried out with three different gaseous atmospheres and the dynamic wetting spread factors were correlated to the interfacial heat transfer coefficients.

Jan 1, 2005

By A. W. Jolliffe

AEROPROSPECTING may be defined as the application of the air view to the search for mineral deposits. The term is suggested as a preferable alternative to either aerial prospecting (which may be confused with areal prospecting) or air prospecting. The air view may be obtained by visual observation from an aircraft or by examination of air photographs; each has its particular advantages and disadvantages. Aeroprospecting should be regarded only as an aid to, and not as a substitute for, accepted prospecting methods ( l ). The Precambrian region north of Great Slave lake consists of two well defined physiographic units, a feature first noted by J. T. Wilson (2). The boundary between these lies close to the north shore of the east arm of the lake and extends northwesterly near Spencer, Beniah, Carp, and Ghost lakes (Figure 1). South and west of this line, exposed bed-rock makes up the greater part of the land area; eskers are very rare, and overburden is largely limited to rock-walled valleys and depressions. North and east of the line, outcrops are rare or absent, eskers are abundant, and most of the surface consists of drumlin-like drift hills, elongated parallel to the direction of ice movement (Figure 2). Where this boundary passes through the area shown in Figure 1, it lies near the 1,200-foot contour and may mark the maximum extent of the lake or sea arm present in this vicinity toward the end of the Pleistocene period. For convenience, the first area may be called the 'bed-rock belt' and the other the 'drift belt'.

Jan 1, 1945

By Guangdong Institute of Resources Comprehensive Utilization, Y. H. Tang, H. X. Hu, T. S. Dong, Z. H. Zhang

"A world class rare metals ore deposit in Africa belongs to a massive granite type poly-metallic pyrochlore-niobium resource. Successful project development in realizing the resource is vital to Africa’s economy and pyrochlore processing technology.The ore properties are quite complex due to the presence of varieties of valuable minerals, fine dissemination and intimate association of minerals and the relative abundance of easy-floatable minerals. The separation of pyrochlore from zircon, calcite and mica is generally considered difficult. Whilst studies have previously been conducted by several independent institutions overseas, no satisfactory process has yet been developed to date for the ore deposit—possibly due to the process designed being too complex; high cost of regents; lower performance.Based on process mineralogy study and extensive testwork, the authors have in recent years developed a new technology—“De-slime—Iron-rejection—Zircon (with calcite) and Calcite reverse flotation—Pyrochlore flotation”. The flow-sheet is characterized by ?1prior removal of slimes and iron minerals; ?2 Zircon (with calcite) and Calcite reverse flotation; and ?3Pyrochlore flotation applying new type of chelating collector GYX3 developed by GZRINM in conjunction with selected regulators and depressants.The process involved in the new technology is simple to implement and facilitates stable operation; the flotation reagent regime is easily adaptable; the cost of main reagent is lower largely because it is easy to manufacture and is environmental friendly. Laboratory test results demonstrated that, for raw ore assaying 0.35% Nb2O5, 0.03% Ta2O5 and 0.45% ZrO2, pyrochlore concentrate grade of >35% Nb2O5 could be obtained with >74% recovery. Meanwhile, the Ta2O5 content in pyrochlore concentrate could be recycled, and ZrO2 recovery >50% could be achieved in zircon concentrate assaying ZrO2>63%—significantly improving the technical-economic indicator. These results were verified in pilot trials of 1.44t/d throughput. The paper presents the new technology in whole, summarizes the key factors affecting its performance and discusses in simple terms the mechanism of separation."

Jan 1, 2016

By George R. Elliott

Introduction The pages that follow present a brief chronological survey of views which have been held, and of legislation enacted, for the regulation of the natural gas and oil industry in the Turner Valley field, especially as regards conservation of the natural gas. To provide a necessary background for an adequate understanding of the progress of events in western Canada, there is included also a compilation, from technical and legal authorities, of some of the more important measures which have been adopted for the regulation of the oil and gas fields of the United States, where these measures have had, or are likely to have, a bearing on the course of our domestic industry. Owing to exigencies of space, it has been possible to refer only to the most outstanding proposals and legislation, and to these in the briefest possible form. Although, so far as Canada is concerned, the data presented are restricted almost entirely to the Turner Valley field, it is the hope of the writer that the paper may prove of value for purposes of reference: for any similar gas and oil fields discovered in western Canada will certainly revive and intensify the problem of the proper steps to be taken for the conservation of the gas. Definition of 'Conservation The term conservation has been so misunderstood and misrepresented that, to many persons in Alberta, it means little more than closing-in wells. In the light of the definition of Charles E. Hughes, that 'True conservation of a raw material is its economical use', the subject of natural gas conservation is inseparably involved with the study of the function of the -gas and with the development of the principles of unit operation.

Jan 1, 1934

By L. H. Rajala, K. H. Singh

"This paper presents the results of a detailed feasibility study carried out to investigate whether a low-grade deep underground mine of Falconbridge Nickel Mines Ltd., closed since 1975, could be made more productive and profitable by the introduction of new mining technology. For this purpose, recent advances in mine design and development concepts, larger and better designed machines, such as hydraulic drills, high-pressure down-the-hole machines, LHDs, new blasting concepts, more efficient and improved stoping methods, and ground control technology were considered. Technical and economic analyses incorporated the latest computer-based techniques. The mine was reopened in 1979 and the paper concludes with an assessment of actual progress and performance compared with that planned and forecast.IntroductionThe East Mine orebody, located between the Falconbridge Mine and Inco's Cryderman Mine in the Sudbury District of Ontario, has been in production since 1956. From 1956 to 1978, about 5.6 million tons of ore had been mined from this ore zone. The ore body is low grade and was developed as a cut-and-fill operation. Due to high operating costs, the mine has been shut down several times during economic downturns. The latest closure was in 1975 due to a lower demand for metal.In 1978, investigations were initiated to assess the economic and technical feasibility of mining this ore using new developments in mining technology. In this study, consideration was given to the application of bulk mining methods with a potential for higher productivity, trackless development utilizing efficient LHD machines and hydraulic drills, new blasting and fragmentation concepts, and new ground control technology. Advanced computer techniques, such as finite element, for mine design and rate of return with discounted cash flow analyses for the economic comparison- of various mining options were utilized for a rapid and comprehensive assessment during the feasibility stage."

Jan 1, 1981

By T. R. Kostecki

"Instrumented rock bolts are effective tools for assessing the reinforcement and condition of immediate roofs; however, instrumentation can have relatively high costs, which can be justified by high reliability and repeatable and representative data measurements. The instrument’s durability and operational life are of great importance, along with accuracy, applicability, and usefulness. This paper develops reliability models for three instrumentation technologies used in slotted rebar, drawing data from studies at five underground coal mines. Three case studies demonstrate instrument applicability and usefulness. Finally, two types of instrumented rock bolts are used to determine the direction of bend and maximum bending strain. RÉSUMÉ Les boulons d’ancrage instrumentés sont des outils performants qui permettent d’évaluer la consolidation et la condition des toits immédiats. L’instrumentation peut cependant se révéler très onéreuse, des coûts qui se justifient par sa fiabilité élevée ainsi que par des mesures de données reproductibles et représentatives. La durabilité de l’instrument et sa durée de vie opérationnelle sont très importantes, de même que son exactitude, son applicabilité et son utilité. En s’appuyant sur des données issues d’études menées dans cinq mines de charbon souterraines, cet article développe des modèles de fiabilité pour trois technologies d’instrumentation utilisées pour des barres d’armature nervurées. Trois études de cas démontrent l’applicabilité de l’instrument et son utilité. Enfin, deux types de boulons d’ancrage instrumentés sont utilisés pour déterminer la direction de la flexion et la contrainte de flexion maximale.INTRODUCTION Using instrumented rock bolts to monitor strain changes in a rock bolt array allows engineers to understand the per-formance and effectiveness of the rock reinforcement system and the response of the rock mass to such support; however, instrumentation remains a niche solution for solving complex ground-control problems—particularly for underground coal mines, which is where they are needed most. From 2000 to 2016, fall-of-ground fatalities still accounted for an average of approximately 30% of the total annual underground coal mine fatalities in the United States alone (United States Department of Labor, 2018). These tools would also be useful for deep hard-rock mining conditions. The main reasons for the lack of widespread use are not only cost but also accuracy, applicability, implementation procedures, intrinsic permissibility, and reliability (Peng, 2015). As a result, measurements of coal mine roof behaviour using instrumented rock bolts are quite scarce, not widely published, or inadequately presented to provide a seamless understanding of a roof’s response to support."

Jan 1, 2018

By F. Tanaka

Copper losses to discard slag have long impacted on the profitability of copper smelters. Businesses based on the treatment of secondary materials have also revealed that copper losses are indices of precious-metals losses. Many custom smelters are thus required to obtain more reliable controls for reducing copper losses than ever before. Mitsubishi Materials Corp. has cooperated with academic research institutes in conducting research projects on the pyrometallurgical fundamentals of copper smelting systems, including mutual evaluation of magnetite behavior between synthetic and industrial slags. The state-of-the-art pyrometallurgy has subsequently been introduced to Naoshima smelter for controlling the Mitsubishi process. The revised controls function successfully and the operational results demonstrate that avoiding the discharge of solid magnetite from the S-furnace is quite effective to reduce copper losses. Magnetite behavior has been controlled over the Mitsubishi process so as to reduce copper losses while satisfying the needs of recycling businesses growing in Japan. In-situ estimation of magnetite behavior using the absorbed heat from the melts to cooling water will also be discussed.

Jan 1, 2007

By Stanley G. Butcher

"Introduction Many operators in western Canada, with a background in the minerals industry, talk of ""coal beneficiation"", whereas the coal industry generally uses the term ""coal preparation"" . The sophisticated cleaning circuits and thermal drying units found in western Canada makes the term beneficiation particularly appropriate. This chapter uses standard coal preparation terminology(l,2J and assumes general knowledge of coal preparation unit processes and equipment(3,4,5). The geologic setting and mining methods of western Canada, described elsewhere in this volume, present for preparation run-of-mine coals which have particular problems. As a result the cost of preparation is a higher proportion of the total minesite production costs than in other coal fields . Preparation requirements are determined by the types of coals being produced and the markets in which they are sold. Western Canadian coals have a low sulphur content and do not require cleaning on this account. Prepared coal from western Canada has to be shipped vast distances -to the Pacific Rim countries and Ontario in particular -and the savings in transport costs justify the high costs of preparation. Factors which dictate selection and operation of the preparation processes are: i) Market specifications and coal rank. ii) Size distribution of particles and particularly the liability of coal and refuse particles to degrade during handling and processing. iii) Quantity and characteristics of the associated refuse. iv) Washability characteristics (the distribution of particles by specific gravity within each size fraction). v) Surface characteristics of the fines. vi) Variability of the raw coal. Where the product (coal or discard) has a high fines content special consideration must be given to dewatering, the removal of surface moisture, to give acceptable handle ability characteristics. In the severe winter climate of the western foothills and mountains thermal drying is necessary to prevent freezing of washed coal in stockpiles and railcars."

Jan 1, 1985

By A. Mitura

The paper presents the initial investigation of possible energetic applications of chosen wastes from groups: 06, 03, 05 and 01, including coal slimes being secondary product of hard coal processing. These categories of wastes are catalogued according to the polish law, where 06 ? wastes from production, preparation, purchasing and application of products of non-organic chemistry; 03 ? wastes from wood processing and from plates and furniture, celluloid mass, paper and card board production; 13 ? oil wastes and wastes from liquid fuels; 01 ? wastes produced by searching, extracting, physical and chemical processing of ores and other mineral raw materials. The change of combustion heat value was evaluated in produced energetic mixtures containing these types of wastes together with the change of their individual components. All combinations of ingredients were taken into consideration giving 256 various mixtures, from which 36 were selected to investigation. This allowed the performance of statistical factor analysis. For such prepared materials the application of regressive method was proposed in purpose of calculating combustion heat value and then the comparison of empirically determined and theoretically calculated heat values was performed. The change of regressive coefficients can be determined by the nature of Hess law (eq. 1) what was investigated and the attempt of its explication and validation was done.

Aug 1, 2013

By Mario Gerards, Axel Wellendorf, Arulnesan Rajesh

"In times of increasing energy cost and global demand for improved machine technology, the optimization of industrial mineral processes in terms of efficiency and production cost is an important factor when choosing industrial equipment suppliers. Of course this applies for screening machines, feeders and distributers as well!Besides of the ability of a screening machine for being adjustable to changing requirements during the production process itself, it becomes more and more important to choose the correct screening machine type, peripheral equipment for arising screening tasks and to optimize the overall design of the screening machine starting at a very early stage.The different types of screening machines bring many advantages and disadvantages with them. The selection of the correct type of screening machine can improve the flow rate, energy, efficiency, yield, quality, output, availability and decrease the maintenance costs and structural steel work.The machine optimization has to be a consecutive process in which at any time results of simulation and “real-life measurement” are compared and the findings are implemented in machine development and design. As an example, it is possible to reduce machine weight and reinforce the steel structure of a screening machine at the same time, which enables the manufacturer to use smaller drives for the screen.This paper will present the methods ANSYS and 3D Solid Works used at RHEWUM GmbH for this way of optimizing machine design and construction and examples for results gained from this continuous improvement process."

Jan 1, 2016

By A. Ojaghi, A. R. Mohammadi

"The Marvast monazite deposit is located 35 kilometres south - southwest of Marvast in Yazd province of Iran. A representative sample weighing approximately 10 tons was prepared to study the amenability of the ore to physical beneficiation. The size fraction of +1000 µm was removed due to low monazite content and the –1000 µm size fraction was concentrated by the gravity-classification-magnetic methods. According to the results of sample characterization, the representative sample contains 220 ppm REO that is contained in monazite. It was concentrated to 41.5% REO by the above mentioned methods. The recovery of REO in the monazite concentrate was 41.5%.INTRODUCTIONRare earth elements are critical metals in many countries (Gupta, 2005; UK Geological Survey, 2011). Increasing application of these metals in hi-tech industries and price fluctuation caused by Chinese production policy has led other countries to focus on their local resources (UK Geological Survey, 2011). In this case, Iran is not an exception.REE mineralization in Iran is mainly located in the central zone. Regarding the exploration data, these deposits are divided into two categories. The first group is iron ore deposits in which the REE are carried by phosphate minerals. The other group is placer deposits where monazite is the major mineral of the deposit. The Marvast placer deposit is one of these types of deposit (Daliran, 1990; Mokhtari, 2008; Torab, &Lehmann, 2007; Alipour, 2014)."

Jan 1, 2016

By M. A. Rabah

This study aims to recover europium, yttrium metals, some valuable salts or oxides from the white powder (apatite) coating the inner surface of spent florescent lamps (SFLs). Pressure leaching using sulphuric/nitric acid successfully dissolved the metals of interest. Europium or yttrium metals were obtained by hydrogen reduction of their oxides. Addition of potassium thiocyanate converted the dissolved sulphates to thiocyanates. Selective separation of Eu and Y was then carried out by solvent extraction from the thiocyanate solution. The used solvent was trimethyl-benzylammonium chloride. N-trihutylphosphate in 1 M nitric acid was used to strip the metal loaded in the organic phase. Results showed that the quality of the cleaned glass tubes of the SFL met the standard requirement for the lamp manufacture. The white powder (WP) is composed of calcium sulphate 35.2%, phosphate 61.5% and oxides of europium and yttrium 1.65%wt. respectively. Autoclave digestion of the WP for 4 h at 120°C and 500 kPa in sulphuric acid/nitric acid mixture dissolved 96.4% of yttrium and 92.8% of europium. The conversion rate of sulphate to thiocyanate was favoured at low temperature. Stripping of Eu and Y from the loaded organic phase behaved in an opposite way. A metal separation factor of 9.4 was obtained. ate recovered europium and yttrium salts were selectively separated using ethyl alcohol or dilute nitric acid. Yttrium was very soluble while europium was not. Europium and yttrium metals were obtained by hydrogen gas reduction at 850°C and 1575°C respectively.

Jan 1, 2004

By C. Greimel

Modern roadheaders provide a safe and cost-effective, yet very flexible way of mechanical tunnel and roadway excavation. In the last years, SANDVIK Mining and Construction has developed a NEW ROADHEADER GENERATION, which incorporates new features, allowing significant improvements of underground excavation. Partial face cutting machines such as roadheaders excavate the desired profile by means of a cutter unit mounted on a swiveling boom. This flexible method for mechanical excavation makes the roadheader suitable for a large range of profile varieties and most rock characteristics. Over 1,250 roadheaders have been delivered since the 1960s from the Zeltweg plant of Sandvik Mining and Construction, with the current products ranging from the light-duty, 130kW MR220 machine, widely used in the tunneling and coal industry to the heaviest 300kW tunneling and hardrock mining roadheaders. Roadheaders are generally used in coal mine development, salt/potash mining as well as construction and hard rock mining. This paper describes the technology behind the succesful introduction of hard rock cutting with roadheaders, and aims to offer best practise operation experiences from various hard rock cutting sites.

Oct 1, 2010

By D. W. Davis, P. Landais, L. J. Robb

Abstract -Nodules of carbonaceous matter have been observed in several Archaean peraluminous granites adjoining the gold- and uranium-bearing Witwatersrand Basin. These nodules, which resemble solid bitumen, usually replace uraninite or uranothorite and are paragenetically late. They show many similarities to kerogen seams and nodules associated with the conglomerate horizons in the Witwatersrand Basin, including composition, maturation, intimate association with uraninite, and a late paragenesis. U-Pb isotope ratios for granite-hosted and Witwatersrand kerogens define a single, albeit somewhat diffuse, Pb-loss discordia suggesting an upper intercept age of circa 2300 Ma. Carbon isotope analysis indicates lighter ?13C values for the granite-hosted nodules than for the sediment-hosted kerogen seams. Raman spectroscopy indicates that granite-hosted kerogen is more highly ordered than Witwatersrand seam kerogen. A model is presented which links the granitoid­ and sediment-hosted organic matter to an event of oil generation in the Witwatersrand Basin circa 2300 Ma ago. Light hydrocarbons migrated through the sediments and into underlying/adjacent granitic rocks, undergoing polymerization and accumulation in response to radiation accompanying the presence of high-uranium phases.

Jan 1, 1994

By H. Marquis

This paper is concerned with an analysis of a number of failures of large-size, hypervelocity light gas gun chambers and barrels. A brief description of the light gas gun principle and of the various types of guns is first given. The failures and the investigations carried out are then described in detail, with the failures divided into two groups. The first group comprises those failures caused by certain conditions to which the guns may be submitted, and includes, for example, severe local heating of the bore surface causing hardening and cracking of the steel. These conditions were accidental and steps were taken to prevent them. The remaining failures were due to faults in the material or in the heat-treatment, manufacturing or assembling procedures. Specific problems, such as hydrogen embrittlement, and the use of high strength gun barrels above their ductile-brittle transition temperature by preheating prior to firing, are briefly considered. Some interesting observations are also presented on the use of surface markings, and angles of fracture of large fragments, as an

Jan 1, 1962

By H. Tudeshki

A great amount of aggregate is utilized in civil engineering applications such as road construction, railway infrastructure, concrete production, etc. Igneous rocks are the preferred raw material due to their high strength and abrasion resistance. Rock quality assurance is a key factor and has great influence on the quality of constructions in civil engineering. One of the major problems encountered by both the producers and users of igneous aggregate rock is the fact that, with the passage of time, some specific rocks lose their strength, up to a complete loss of structure, i.e. disintegrate and degrade. This phenomenon has a great influence on the quality, strength and durability of aggregates. In the last decades, different methods and procedures such as the glycol test, the methylene blue dye test, as well as the Los Angeles test, have been introduced to distinguish rock properties, and to identify these problems. However, as these wet-chemical methods are time consuming, hard to perform, only to be applied to hand-piece samples, requiring special laboratory equipments, and are only possible to be accomplished under laboratory conditions, their application has always been severely limited. To address this widespread quality management problem of the quarry industry, a relatively quick, easy and user-friendly approach is necessary. It calls for a systematic solution with a device that can simply be used in the day-to-day routine of a mine for quality control of the quarry´s daily production. Our research is concentrated on developing a systematic method for early recognition and diagnosis of rock quality, in order to control and manage the quality of the quarry production in advance. Our new approach is based on two rock parameters: magnetic susceptibility and loss on ignition. The measurement of these parameters provides reliable information on the quality of the rock and allows the quality control process to be accomplished and performed at the borehole location. Our new approach has been assessed through extensive field and laboratory studies and has been implemented on the drill-cuttings of a basaltic andesite quarry. The results of the experiments are discussed in detail, including their impact on increasing resources and environmental protection.

Aug 1, 2013