Search Documents

By Claude A. Jr. Seger

Introduction This paper presents in detailed form the results of settling tests that were published in a few preliminary notes in the April 1949 issue of the Bulletin (p. 166). Carborel is the trade name for sodium carboxymethyl-cellulose and aluminium carboxymethyl-cellulose produced by the reaction of monochloroacetic acid on the alkali cellulose to form an ether. The water-soluble sodium carboxymethyl-cellulose has been known in Europe for several years as sodium cellulose glycolate and has been marketed under several trade names. These cellulose ethers, however, are relatively new in North America, where the name carboxymethyl-cellulose is often abbreviated to C.M.C., or they are referred to as cellulose gum. The particular grade of Carboxel used in the settling tests in the mill of Chesterville Mines, Limited, is the high-viscosity sodium carboxymethyl- cellulose known as Carboxel H.V. It is a white, fluffy powder and is hygroscopic, although not deliquescent. Carboxel solutions in water are colourless, odourless, and resistant to beat and light. They are stable to alkalies, but are precipitated by acids when the pH is reduced below 4.0, and also by solutions of soluble lead, iron, copper, aluminium, and chromium salts. Solutions of Carboxel exhibit the properties of hydrophilic colloids.

Jan 1, 1949

"IntroductionThe Chairman, in his speech to this body last year in Montreal, stated that the Dominion Coal Board looked to and depended upon the Bureau of Statistics for statistical material, and the Bureau does collect and publish monthly and annual data on coal. It may therefore be asked why an officer of the Dominion Coal Board should prepare and give a talk on statistics.I would explain that it has been our experience in the Board that, since the supply and consumption of coal in Canada is subject to a seasonal ebb and flow, it can be more profitably studied on the basis of a twelve-month period ending on March 31st than of a calendar year, since the end of March does represent a fairly stable end point in this ebb and flow. The figures are not prepared or published by the Bureau on that basis and it has therefore been thought that a presentation on this fiscal-year period would be of interest. The Bureau of Statistics has agreed that this may be valuable and all the data here presented are based on the reports secured from various sources by the Mining, Metallurgical and Chemical Division, Dominion Bureau of Statistics. The only contribution by either myself or the staff of the Dominion Coal Board has been the tabulation in a different twelve month period, and the comments upon the picture presented.It should be noted that the data for the month of March, 1950, are not available in all cases and consequently the figures for that year contain an estimate for this month."

Jan 1, 1950

By A. A. el-Geassy, A. A. el-Tawil, Hesham M. Ahmed, Bo Bjorkman

The Iron and steel industry is one of the most intensive energy consuming processes. The majority of iron making processes is now directed towards the uses of fossil-based energy sources like coke, coal and oil. Recently, emphasis has been paid to replace part of fossil- based energy sources with renewable biomass-derived reducing agents. In the present work, the possibility of the effective use of woody biomass in carbon-iron oxide composites was investigated. Wood powder was carbonized in N2 atmosphere at 300 up to 450oC. The carbon content in the produced bio-char increased with temperature. The porosity of the char arises from maintaining the cellular structure inherent in wood biomass increases with temperature. The reduction behavior of four iron oxide-bio char composites having different fixed carbon content were carried out non-isothermally up to 1200oC in Ar atmosphere using thermogravimetric anlyser (TGA). Quadruple mass spectroscopy (QMS) was also adopted to measure the CO, CO2 concentrations in the off gases resulted during reduction process. The effect of volatile matter on the reduction of iron oxide was intensively studied. The different phases developed in the reduced product were identified by X-ray diffraction (XRD). The reduction of composites was found to proceed in a stepwise manner (Fe2O3?Fe3O4?FexO?Fe).

Jan 1, 2015

By P. Amelunxen

It is well-known that the particle breakage mode that occurs in a semi-autogenous mill is significantly different from that which occurs in a ball mill, enough so to warrant very different lab scale breakage tests and scale-up models. This phenomenon, at the plant scale, leads to changing process constraints depending on the particular properties of the ore. For example, hard or coarse ores might bottleneck the SAG/AG mill throughput, while the ball mills might constrain throughput when milling soft or fine ores. Because the power draw of a ball mill is fairly constant compared to that of a SAG/AG mill, periods of SAG/AG mill bottlenecks lead to increased ball mill circuit specific energy consumption and a finer grinding circuit product size, which together constitute a loss of efficiency of the overall process. Because HPGR circuit throughput is less sensitive to changes in ore hardness, this situation is less common or severe in those circuits. Furthermore, the ball mills are somewhat decoupled from the upstream crushing circuits through the use of surge bins, which also helps to mitigate this effect. As a result, ore hardness variability constitutes a significant cost penalty that should be applied to SAG mill/ball mill/pebble crusher SABC circuits when evaluating the relative economics of different grinding circuit configurations. Nevertheless, the issue is by-and-large ignored, because most current HPGR trade-off studies are based on averaged ore hardness parameters. This paper provides an estimate of the magnitude of this penalty for a typical operation by using Monte Carlo simulation methods and plant data from Freeport-McMoRan?s autogenous, semi-autogenous, and HPGR-based comminution circuits. A case study from an in-house 96K t/d sulphide project is presented to illustrate the concept. It was found that by including variability effects, the trade-off NPV of the HPGR circuit over that of the SAG mill circuit increases to $84 million from negative $33 million, effectively reversing the original decision of selecting a SAG mill circuit for the fixed hardness case.

Jan 1, 2012

By W. D. Haley

The report of the Forestry Committee, presented to the recent Imperial Conference at London, is discouraging in its view of the future of timber resources and supplies. From a review of the forestry situation throughout the world, there is every likelihood that, thirty years from this, a shortage of the soft-woods will be severely felt. In the United States, only about one-third of the present forest area contains virgin timber. This will be cleared at the rate of five and a half million acres a year, so that in twenty-five years it will be about all gone. Canada has only about 27 per cent of her original forests left, and her virgin soft-wood will last but another half century. At the present time, the value of her lumber products is over $300,000,000 annually. During the summers of 1909 and 1910, the Government of Nova Scotia caused an examination to be made of the forest conditions in this Province. The reconnaissance, which was under the direction of Professor B. E. Fernow, of Toronto, involved an examination of the various soils, the rate of growth of the wood, and a general survey of the forest area. The importance to the Province of conserving its forest resources was clearly shown, and a number of recommendations were made, which; however, were never acted upon.

Jan 1, 1927

By Will S. Pettitt

Fracture Network Engineering (FNE) is the engineering design of rock mass disturbance through the use of advanced techniques to model fractured rock masses numerically, and then correlate field observations with simulated fractures generated within the models. Microseismic (MS) monitoring is a standard tool for evaluating the geometry and evolution of the fracture network induced during a hydraulic treatment, principally by source locating MS hypocenters and visualizing these with respect to the treatment volume and infrastructure (Figure 1). The integrated use of Synthetic Rock Mass (SRM) modeling of the hydrofracturing with Enhanced Microseismic Analysis (EMA) provides a feedback loop in which the SRM is constrained by the information provided by the MS data and the in-situ behavior of the fracture network is better understood, leading to informed decisions on future field operations. This paper discusses the technologies used in FNE and some of the developmental challenges we face in order to provide a more efficient and robust application of the approach. One particular challenge is the accurate representation of MS source data within the models (locations, magnitudes and mechanisms), and the ability to correlate these data effectively with field results. This challenge is being overcome by the development of more efficient numerical modeling algorithms, providing simulations in three dimensions at reservoir scale, combined with validation of these algorithms using laboratory and field case studies.

Jun 1, 2012

By G. Van Weert, O. Wang

ABSTRACT: When exposed to microwaves, rocks containing sulphides adsorb energy preferentially over barren gangue and quickly become warmer with minimal energy consumption. This effect makes subsequent machine sorting of ore from waste rocks or overburden possible using infrared sensing. This paper reports on the 2450 MHz microwave response of a variety of sulphide minerals by mesh size and spatial distribution, as they might occur in ore rocks. The implications for infrared ore sorting are discussed.

Jan 1, 2011

By G. Van Weert

ABSTRACT When exposed to microwaves, rocks containing sulphides adsorb energy preferentially over barren gangue and quickly become warmer with minimal energy consumption. This effect makes subsequent machine sorting of ore from waste rocks or overburden possible using infrared sensing. This paper reports on the 2450 MHz microwave response of a variety of sulphide minerals by mesh size and spatial distribution, as they might occur in ore rocks. The implications for infrared ore sorting are discussed.

Aug 1, 2011

By Y. Wang, S. Liu, K. Jiang

China is the world’s largest producer and consumer of non-ferrous metals. In recent years, significant progress has been made in research and commercial application of pressure leaching technology to produce some nonferrous metals. Research and development activities include a low-pressure, low-temperature leaching technology for complex copper concentrates, a hematite process to treat pressure leach solutions from zinc concentrates, and a pressure leaching - solvent extraction process for molybdenum and rhenium. Examples of commercial practices include a two-stage pressure leach technology in a zinc plant in Danxia, a direct leaching technology in a zinc plant in Zhuzhou, a high pressure acid leaching process for a nickel laterite project in RAMU, and a pressure leaching technology to treat arsenic sulfides in a plant in Guixi. The development of pressure leaching technology for the recovery of lead, vanadium, gallium, germanium, and precious metals in China will also be described in this paper.

Jan 1, 2015

By R. A. Payant, J. A. Finch

Under certain conditions of air and moisture, sulphide materials can spontaneously heat, or selfheat. The reaction mechanisms of self-heating are not well understood. Most previous work has involved pyrrhotite because it is the most reactive sulphide. The current work investigates the self-heating behavior of sulphide mixtures composed of sulphides other than pyrrhotite. The four studied sulphides were pyrite, chalcopyrite, sphalerite and galena. The rest-potential was measured for each. Binary mixtures formed as a 1 : 1 weight ratio were pyrite-galena, chalcopyrite-galena, pyrite-chalcopyrite and chalcopyrite-pyrite. The four sulphides and the binary mixtures were subjected to standard self-heating tests. The four individual sulphides did not self-heat. However, mixtures of pyrite-galena and chalcopyrite-galena with rest-potential difference (?E) >0.3 volts did self-heat while the mixtures of pyrite-chalcopyrite and chalcopyritesphalerite with rest-potential differences (?E) = 0.1 volts did not self-heat. The results demonstrate that when certain non self-heating sulphides are combined they can self-heat. A possible explanation based on galvanic interaction and formation of hydrogen sulphide as an intermediate product is discussed.

Jan 1, 2009

By R. P. van Hille, N. Mooruth

Remediation of acid rock drainage (ARD) was performed within a linear flow channel reactor (LFCR) via a floating sulphur biofilm (FSB). A full sulphur species material balance was conducted in order to characterize the sulphide oxidation. The reactor was able to achieve an 82% and 93% conversion of sulphide with a hydraulic residence time of 2 and 5 days respectively. 92% and 55.5% of the converted sulphide reported to the biofilm as sulphur for the 2 and 5 day residence times respectively. The mass transport limitations within the biofilm were identified via a dissolved oxygen gradient profiling system.

Jan 1, 2011

By P. Cheung, J. Gulyas, R. Clary

Over the past 50 years, the use of autoclaves in the metallurgical industry has evolved from final metal recovery (hydrogen reduction) and purification (sulphide precipitate oxidation) to treating whole ores and concentrates. Recent process developments, such as the use of autoclaves for laterite leaching, have necessitated higher temperature and pressure operations, which in turn have seen marked advancements in technology and manufacturing capabilities to keep in step with process demands. This paper will discuss the advances in technology in terms of design, materials and construction of autoclaves and liners, typical dip tube design and geometric layout. This paper will also address specific auxiliary equipment, such as acid and steam injection systems, and components, such as agitator seal systems.

Jan 1, 2004

By L. A. Mells

"A laboratory test program was initiated by the Department of Energy, Mines and Resources as part of the National Uranium Tailings Program to investigate the applicability of a radium selective ion exchange complexer for removing radium from Canadian uranium mining effluents. The test program was carried out by Melis Consulting Engineers Ltd. under contract to the Department of Supply and Services using the Saskatchewan Research Council facilities located in Saskatoon, Saskatchewan.The results of this work showed the ion exchange complexer, Dowex XFS 43230.00, to be efficient in removing radium from contaminated water of uranium mining operations with the ultimate loading capacity of the resin on one type of water treated being determined as approximately 1,600 Bq/cm3 of new resin. Although this resin has potential application for treatment of effluent streams in uranium operations it has been identified that the resin efficiency and capacity is directly related to the chemistry of the water being treated and site-specific testwork is required in order to establish reliable design data for full-scale operations.IntroductionThe possible applicability of a radium-selective ion exchange complexer for removing radium from Canadian uranium mining effluents had been identified and discussed as a possible alternative to present radium removal methods during a review of disposal technology options for the National Uranium Tailings Program of the Department of Energy, Mines and Resources(1). Work by other workers(2.3) had shown the complexer to be very efficient in removing radium from contaminated water. Also, plant trials on contaminated minewater at the Mt. Taylor uranium mine in New Mexico is reported to have shown the resin complexer to be efficient under plant operating conditions.As a result, a laboratory test program was initiated by the Department of Energy, Mines and Resources as part of the National Uranium Tailings Program to investigate the suitability of this resin for Canadian uranium mining effluents. The test program was carried out by Melis Consulting Engineers Ltd. (MCEL) under contract to the Department of Supply and Services using the Saskatchewan Research Council (SRC) facilities located in Saskatoon, Saskatchewan."

Jan 1, 1985

By Neil Camarta

$6 Billion Dollar Education ?? Construction is like war ? you need a command and control organization ?? A strong Owner?s team is a must ?? Smaller is better ? break the project into bite size chunks ?? New technology is risky ? lots of construction and start-up risk ?? Safety can be successfully managed ?? Don?t expect contractors to ?work well together? ?? Never, ever let Mining Engineers run stuff than can catch fire

May 1, 2008

By J. Kabuya Mukendi, F. Brunet, J. Hadjigeorgiou, P. Matte, D. Leblanc, M. Grenon

La stabilité des bancs miniers est un élément important de la conception des fosses. Il n’y a pas de consensus sur les critères à utiliser pour évaluer la fiabilité des bancs miniers. Lors de la conception des fosses, la fiabilité des bancs miniers est analysée à l’aide d’un ou deux critères. L’objectif de cet article est d’analyser l’efficacité de la conception des bancs miniers de la fosse Tiriganiaq du projet minier Meliadine par rapport à des critères de fiabilité rencontrés dans la littérature et la pratique. L’article présente les similitudes et les différences entre les résultats obtenus pour les différents critères et propose une approche multicritère systématique pour évaluer la fiabilité des bancs miniers à l’aide de cartes de susceptibilité.

Jan 1, 2012

By James K. B. Booth

The natural crustal abundances of the principle metals of commerce are examined in relation to production and prices for each metal. Two factors, the abundance x price ratio (BP factor) and abundance/production (B/T factor) are listed for each metal. Ideally, for these desirable commercial metals, each factor should be a constant and the same for all metals; comparing the divergences for the full list of metals allows conclusions to be drawn on the relative degree of natural availability of each metal and the ease or difficulty of winning the metal from the earth's crust. Plotting the two factors for each metal over the past decade of steady industrial usage illustrates the anomalous position of copper and, to a lesser degree, molybdenum and it is concluded that over the long term the price of copper will continue to rise steeply. Possible future prices for copper are examined and a suggested preferred order of ranking of the metals as exploration targets would be copper, nickel, tin, zinc, silver, molybdenum and lead, for the near term, with molybdenum possibly increasing its ranking in the list within the next decade.

Jan 1, 1971

By Minerals Refining Company, Gerald Luttrell, Biao Li, Robert Bratton, Roe-Hoan Yoon, Stan Suboleski, Nikhil Gupta

Flotation is regarded as the best available method of upgrading coal and mineral fines in the mining industry. However, its efficiency deteriorates rapidly with decreasing particle size. Furthermore, ultrafine concentrates are difficult to be dewatered economically. Due to these technological problems, some operators are forced to discard at least part of the ultrafine materials to tailings (or refuse) ponds, causing significant losses of valuable resources and creating environmental concerns. To address these technological issues, a new separation process named hydrophobic-hydrophilic separation has been developed on the basis of the recent advances in the science of hydrophobic interactions. The results obtained to date show that the process can recover and dewater ultrafine particles simultaneously with high separation efficiencies. Following a series of extensive laboratory tests, the process has been scaled up to proof-of-concept and pilot-scale continuous tests. The results obtained with desliming cyclone overflows, screenbowl effluents, and by-zero coal flotation feeds can be cleaned to less than 4% ash and moisture with over 97% organic matter (or coal) recoveries. The results obtained with mineral fines also showed encouraging results.

Jan 1, 2016

The Autogenous milling of ores holds an increasing attraction as the focus moves towards reducing energy usage, both direct and embodied in grinding media. However, most of the early AG mills were converted to SAG for improved stability and increased throughput. This imposes a huge penalty in steel grinding media consumption. The LKAB iron ore operations in Sweden process highgrade magnetite through fully-autogenous milling lines to a final product P80 of about 45µm. The outcomes of P9O AMIRA research surveys, covering a wide range of mill fillings and throughputs and with different feed blends, are presented. Insights are provided on operational strategies, opportunities, the influence of feed size control and balancing the blend of competent gangue and softer magnetite. Areas of importance in the successful operation and control of energy-efficient autogenous circuits are highlighted.

Jan 1, 2012

By J D. McDonald

This paper outlines the function of the Safety and Compensation Division of the Mining Association of British Columbia. After a general discussion of safety and the safety program now being followed in B.C., the author goes on to describe the wide-ranging aspects of compensation payments and company assessment rates. Special attention is also given to the problem of silicosis in mining operations. In appendices to the paper, the experience rating plan of the mining industry is compared to that recently adopted for the construction industry. Introduction The Mining Association of British Columbia consists of fifty-five member companies, including virtually all the producing mines as well as the larger exploration, contracting and development companies. On completion of an extensive study of safety and compensation in the mining industry, the Mining Association of British Columbia instituted a Safety and Compensation Division in 1954. The director of the Safety and Compensation Division reports to the Executive Committee of the Association. There are two main functions of this Division. First is the prevenion of accidents by encouraging

Jan 1, 1965

By Tom Setterfield

Conclusions ?Canada is a prospective place to explore for IOCG deposits ?Time distribution of IOCG mineralization in Canada mimics that in the rest of the world ?Canada may have been the first country to start mining IOCG deposits ?Production from newly discovered IOCG deposits in Canada may start soon

May 1, 2006