Search Documents

By Minghao Hu, Hongbo Zhao, Jun Wang, Wenqing Qin, Rui Liao, Central South University

"In the present work, X-ray diffraction (XRD) analysis, X-ray photoelectron spectroscopy (XPS) analysis and electrochemical analysis were carried out to investigate the intermediate species and electrochemical dissolution process of chalcopyrite in the presence of sulfur and iron oxidizing microorganisms. For bioleaching of chalcopyrite by the sulfur oxidizing microorganism Acidithiobacillus caldus, the redox potential was always lower than the appropriate value and chalcopyrite was mainly directly oxidized to polysulfide (Sn 2-), thus resulting in low copper extraction. As for bioleaching of chalcopyrite by the iron oxidizing microorganism Leptospirillum ferriphilum, chalcopyrite was mainly directly oxidized to polysulfide at the initial stage where redox potential was lower than the appropriate value and resulted in low dissolution rate. At the middle stage where redox potential was appropriate (about 350–480 mV vs. Ag/AgCl), chalcopyrite was mainly transformed to intermediate species of Cu2S rather than polysulfide, thus resulting in high dissolution rate. At the later stage where redox potential was higher than the appropriate value, chalcopyrite was mainly directly oxidized to polysulfide which caused the later passivation of chalcopyrite. Finally, a model of electrochemical dissolution process of chalcopyrite in the presence of sulfur and iron oxidizing microorganisms was provided.INTRODUCTIONBiohydrometallurgy is considered as one promising mineral processing technique in processing low grade ores due to the advantages of simplicity, low cost and eco-friendly. Chalcopyrite (CuFeS2) is the most abundant copper-bearing resource, accounting for appropriately 70% of the known reserves in the world, while is recalcitrant to bio-hydrometallurgy mainly due to the coated passivation layer (Klauber, 2008; Li, Kawashima, Li, Chandra, & Gerson, 2013). However, the detailed dissolution and passivation mechanisms of chalcopyrite bioleaching are still uncertain. The microorganisms assisting chalcopyrite dissolution can be mainly classified into three types, including mesophilic microorganisms (e.g., Acidithiobacillus ferrooxidans, Acidithiobacillus thiooxidans and Leptospirillum ferrooxidans), moderately thermophilic microorganisms (e.g., Acidithiobacillus caldus, Sulfobacillus thermosulfidooxidans and Leptospirillum ferriphilum), and extremely thermophilic microorganisms (e.g., Metallosphaera sedula, Sulfolobus sp., Acidianus sp., and Sulfurcoccus mirabilis). Moderately thermophilic microorganisms have a better prospect in the future industrial application of chalcopyrite bio-hydrometallurgy (Olson, Brierley, & Brierley, 2003; Rohwerder, Gehrke, Kinzler, & Sand, 2003). Hence, investigating the detailed dissolution and passivation mechanisms of chalcopyrite bioleaching by moderately thermophilic microorganisms is of important significance, which will provide essential information for promoting chalcopyrite bioleaching by moderately thermophilic microorganisms in laboratory or industrial plant."

Jan 1, 2016

By J. Shahabpour

"Many porphyry copper deposits of the Kerman copper province in central Iran are associated with a consistent structurally con-trolled main drainage pattern, which is shown in this paper to be a useful regional prospecting tool in the search for new deposits. The main drainage trends also generally allow the distiction of high-grade (>0.2% Cu) from low-grade (<0.2% Cu) deposits. Topographic maps1:50 000 or geologic maps 1:100 000 have been found suitable for identification of promising drainages.IntroductionTrends of the main drainage systems transecting the high-grade porphyry copper deposits of the Kerman Region in Iran coincide with Quaternary age regional faults and fractures. Observation of such drainage trends can expedite regional evaluation prior to field examination. Thirty deposits located in the Kerman Region (Fig. 1) have been studied to identify common features that can be used for exploration purposes, especially for the first stage of regional exploration. A variety of field criteria are available for subsequent rapid field checking prior to trenching and more costly methods such as drilling, etc.Characteristic geomorphic features have been considered as aids in mineral exploration by many authors (e.g., Faniran, 1971; Piotrovski and Lubkashov, 1976; Verstappen, 1983). Clark et al. (1967) indicated the relationship between geomorphology and the supergene enrichment of copper in Atacama Desert, Chile, and correlated three periods of supergene enrichment with three periods of pediment disection. Seeland (1978) used fluvial drainage patterns for uranium and hydrocarbon exploration in the Wind River basin, Wyoming. Postolenko and Konopleva (1973) used the reconstruction of ancient valley systems for exploration of gold placers"

Jan 1, 1996

By Fred C. Delabbio

The successful implementation of a new technology in an underground production mine requires many challenges to be overcome. These challenges include mine hardening of new technology, mitigation of safety risks and hazards, mine operation support, and technology transfer to mine staff. In the end, the majority of these challenges relate to the human aspects of implementation. The approach selected to overcome these challenges must be customized and appropriate for each unique situation. This paper outlines the approach used to address these challenges as part of successful implementation and resulting demonstration of the hydrogen fuel cell locomotive at the Placer Dome (CLA) Limited, Campbell Mine. This technology demonstration at Campbell Mine is critical for determining technical, regulatory and implementation aspects to be incorporated into future fuel cell prototypes such as the LHD project.

May 1, 2003

By William Petruk, J. R. Schnarr

The behaviour of minerals during flotation of a fine-grained pyrite-rich base metal ore was investigated by studying the feeds. concentrate and tailings from every flotation cell in the mill of Brunswick Mining and Smelting Corp. Ltd. Bathurst. New Brunswick. The samples were analyzed for Zn, Pb, Cu. Fe, Ag. Sb, Sn, Bi, In. Hg, Mo and As. Mass balances were computed and recoveries of all metals from each cell. from each circuit and from the mill were calculated. The percentages of sphalerite. galena and chalcopyrite occurring as free grains in each product were determined with an image analyser, as were size analyses for free mineral grains and middling particles, and compared with screen analyses. The results show that the behaviour of minerals is defined much better by the recovery of free mineral grains than by the recovery of elements. The recovery of free sphalerite in the zinc circuit is 96 wt %, whereas Zn recovery from the same circuit is 88 wt %. the difference being due to unliberated sphalerite. The recovery of free sphalerite from the mill feed is 88 wt % and Zn 78 wt %. The recovery of free galenafrom the mill feed is 88 wt % and Pb 64 wt %. The recovery of free chalcopyrite is 75 wt % and Cu 45 wt %. Size analyses show that more sphalerite and chalcopyrite can be liberated by regrinding. but the galena is so fine grained that regrinding would not necessarily improve liberation. Silver occurs mainly in tetrahedrite and galena; the main loss in the tailings is due to large (+ 26 um) and small (-1 um} free and unliberated tetrahedrite grains.

Jan 1, 1981

By James A. Robertson

"The Pronto Mine located at the east end of Lake Lauzon, Long Township, some 12 miles east of Blind River is of historic note being the discovery locality and the first producing mine of the Elliot Lake uranium camp. Radioactive bedrock was discovered in 1949, a commercial deposit was verified in 1953 and production commenced in 1955. Production continued to April 1960: total tons milled 2,264,404 from which 4,643,835 pounds U,O, were recovered at a recovered grade of 2.05 pounds U3O8 per short ton.The orebody is in a bed of pyritic quartz pebble conglomerate at the base of the Matinenda Formation of the Elliot Lake Group of the Huronian Supergroup. The rocks strike east and dip 15 degrees to 20 degrees south and unconformably overlie Early Precambrian granite, the upper surface of which is marked by a regolith. Several diabase dykes cut the orebody which is also affected by albite, chlorite, and carbonate-rich alterations. To the south the orebody is cut by a fault. The orebody is 6to 10 feet but locally 10 to 15 feet thick, has a strike length of 3,500 feet and extends down dip for 3,600 feet to a depth of 1,000feet. Some 300,000 tons of ore grade mineralization remain in the deeper portion of the mine.IntroductionThe Pronto Mine, (Photo I) at the east end of Lake Lauzon in Long Township some 12 miles east of Blind River, is of particular interest as being the discovery site and the first producing mine of the Elliot Lake camp.Production at the Pronto Mine commenced in 1955 and continued until 1960 when the mill was converted to treat copper ore from the nearby Pater Mine at Spragge. A description of both mines, based on material provided by the mine staff, was given in the report on ""Geology of the Spragge Area"" (Robertson, 1970).As little study has been done on Pronto geology or petrology since mine closure, the earlier description of exploration and geology is essentially repeated, but shortened, here- the main change being that the stratigraphic terminology has been amended as recommended by the Federal-Provincial Committee on Huronian Stratigraphy (Robertson et al., 1969)."

Jan 1, 1986

By W. A. Haley

This paper discusses how a large wheel loader should be equipped, with particular attention paid to tires and tread life, and describes the several steps that can be taken to provide favorable working conditions and reduce over-all costs. A comparison is then made of wheel loader production and costs vs those of power shovels, and the present and possible future applications of the wheel loader are outlined.

Jan 1, 1969

By B. K. Gorain

"The Air-Metabisulfite (AMBS) process has been developed to treat complex copper, molybdenum and precious metals (gold, silver) bearing ores using brackish and sea water. This process was able to produce significantly better copper concentrate grades and higher recovery than possible using conventional lime and/or cyanide based processes for certain complex ores with high sulphide gangue minerals. The AMBS technology in now used commercially following a rigorous evaluation process emanating from laboratory curiosity to plant applications. In addition, many projects have embraced this technology at a feasibility level involving various complex ore bodies.This paper presents a summary of the findings from testing the AMBS technology on various ores types. Experiences gained from this successful development from bench to piloting and then to plant applications are also presented in this paper.INTRODUCTIONProcessing of sulphide copper, molybdenum and precious metal ores typically involves flotation of copper bearing minerals while depressing non-sulphide and other non-copper sulphide minerals such as pyrite, pyrrhotite and sometimes arsenopyrite. Though in many precious metal ores, the values are in these sulphide minerals as well. The conventional method employed in the industry to produce a saleable copper concentrate requires depression of these non-copper sulphide minerals using an alkaline pH above 9.5, though 10.5 to 11.5 is more common. Alkalinity is controlled by the addition of a pH modifier. Lime is normally employed as a pH modifier due to its relatively low cost; however, the costs associated with adding lime can be significant and the effectiveness of lime as a depressant could be drastically reduced when the process water supplied to the flotation circuit contains high level of dissolved salts. In some cases, a small amount of cyanide is used along with lime to depress non-copper sulphide minerals especially when its proportion to copper sulphide minerals in the ore is higher than three."

Jan 1, 2016

By P. T. Bloomer

Introduction Mining of the orebody of the Sullivan mine, which is owned and operated by the Consolidated Mining & Smelting Company of Canada, Limited, has reached a point where pillar extraction is rapidly becoming a major part of the operation. Very few of the larger pillars have been completely extracted; consequently, this paper contains much that is theory and expectation. Due to early mining methods and the physical characteristics of the Sullivan deposit, similar conditions may not exist in other older mines facing the problems of pillar extraction, but it is thought that the methods employed and those contemplated may be of general interest. History The Sullivan orebody, which is at Kimberley in the Fort Steele mining division of the East Kootenay district of British Columbia, was discovered in May, 1892, by Messrs. Sullivan, Smith, Cleaver, and Burchett. After passing through the hands of several owners the property was optioned in 1909, and purchased in 1910, by The Consolidated Mining and Smelting Company of Canada, Limited. Early mining was highly selective, the objective being a clean, high-grade silver-lead ore. By 1923 the difficulties of milling the very complex ore had been overcome and the first unit of a concentrator was completed with a capacity of 2,500 tons daily. Capacity was increased by stages to the present rate of 8,500 tons per day. Concentrates are shipped over the Canadian Pacific railway ? to the Company smelter at Tadanac, British Columbia, for final treatment. Approximately 45,000,000 tons of ore has been mined to date.

Jan 1, 1948

By S. Flewelling, M. Scobie, G. R. Baiden

"SynopsisA feasibility study to develop a research program, the Mine Automation Plan (MAP), was recently completed. This was undertaken by a team comprised of Inco Ltd., Falconbridge Limited, the Canadian Centre for Automation and Robotics in Mining (CCARM) and the Centre for Resource Studies (CRS). The study was sponsored by PRECARN Associates, which is a consortium of thirty-six Canadian companies focussed on research and development in artificial intelligence and robotics. PRECARN Associates was formed in 1987 when a number of research proposals were funded in the fields of process control systems, robotics systems and intelligent engineering systems. In July 1991, PRECARN accepted the next round of proposals for research. The MAP project was one of the successful proposals, being awarded $100,000 for the development of a feasibility study defining a long-term R&D plan for underground hardrock mining automation.The development of the feasibility study started by addressing the fundamental structure of the mining process, and its relationship to the metallurgical process, over-all infrastructure support and management systems (Fig. I).Mining may be considered as comprising five subprocesses: (I) delineation; (2) development; (3) production; (4) backfilling; and (5) infrastructure support services. Within these subprocesses many applications for artificial intelligence and robotics exist. The mining process is dependent upon the interaction between the physical mining process and information. For example, the delineation process is dependent on geomechanical, geochemical and geophysical techniques to develop a model of the orebody based upon access to such data. This same relationship between the physical and information models holds true through the development, production, backfill and infrastructure support systems.The foundation for the MAP study has been the recent development by Inco Ltd. of an underground communications system (Fig. 2). The system has the ability to supply high bandwidth communications, over voice, data and video to mobile and stationary locations within the mining operation. It is seen to be the future backbone of a comprehensive, automated information system which should permit the application of the concept of Computer Integrated Manufacturing (CIM) to underground mining. CIM, through the automated flow of information, has been successful in integrating the engineering, production and various support groups in manufacturing."

Jan 1, 1994

By K. V. Lindell

Introduction This paper describes a recent innovation in the design and construction of mine headframes. A reinforced concrete headframe was built by using sliding forms. A concrete headframe of conventional design was originally considered, but investigation of this project showed that it was doubtful if the bearing strength of the soil was sufficient to support the great weight of a structure of this type. In addition, the slope and the fractured condition of the serpentine bed-rock did not permit satisfactory piling. A conventional steel headframe with storage bins was then designed, but, due to the steel situation, delivery promises were set back many months. The concrete headframe was again investigated, and a design was adopted incorporating a circular headframe lower in height than that first considered, with skips discharging into a smaller surge bin. The upper section of the shaft collar was strengthened to result in a stable structure which would be supported by bed-rock, as well as by the concrete and steel lining of the shaft itself.

Jan 1, 1948

By Jan Kvinge, Aina Opsal Bakke, Yanjun Li, Jan-Ove Løland, Svein Jørgensen

"Compound casting is a very attractive approach to reduce the weight of components for some specific applications while keep both the functional and the mechanical property requirements. In this work, Al-7Si-Mg alloy /copper compound castings were produced through a low pressure die casting process. To reduce the oxide present in the interface, flux coating of the copper pipes was tested. The interface layer formed between the two alloys was investigated using Optical Microscopy (OM), Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS). Vickers Micro-hardness was also measured across the interface. Results showed that the flux coating prevented the formation of the metallic bond between copper and aluminum. Instead, high concentrations of potassium, magnesium and fluoride, coinciding with formation of KMgF3 and MgF2, were detected in the interface. In the castings without surface treatment, a continuous metallurgical bond was achieved. In the bond layer, various Al-Cu intermetallic phases have been detected. In addition, formation of primary silicon particles in the reaction layer was observed in all castings. The mechanism for the formation of the intermetallic phases and the strength of the interface layer have been discussed.INTRODUCTION Recent development in the automotive industry has focused on producing lightweight components, which can reduce CO2 emission and increase the efficiency. Often, one material alone is not able to meet the requirements for a specific use. The need for lightweight bimetallic components has therefore increased. Aluminum-copper bimetallic components can be used in wires and bus bars where conductivity is an important factor (Lee, Bang, & Jung, 2005). Compared to Al-Cu alloys, Al-Cu bimetallic components can reduce both weight and cost without reducing electrical and thermal conductivity (Sheng, Yang, Xi, Lai, & Ye, 2011). A challenge is, however, that aluminum and copper have high affinity to each other, especially at elevated temperatures. This causes formation of brittle intermetallic phases with high electric resistance (Liu, Wang, Sui, Wang, & Wenjiang, 2016). In addition, both metals are subjected to oxide formation on the surface. Copper is especially exposed to oxidation at elevated temperatures (Pinnel, Tompkins, & Heath, 1979), while a thermodynamically stable oxide layer will spontaneously form on the aluminum surface (Papis, Loeffler, & Uggowitzer, 2009). Oxides are known to be passive substrates, which will reduce wettability and will thus prevent the formation of metallic bonding between aluminum and copper (Papis, Hallstedt, Löffler, & Uggowitzer, 2008)."

Jan 1, 2018

By L. Frost

"Since the late 1990s, increased prevalence of severe lung disease among US coal miners has been observed, particularly in central Appalachia where thin-seam mining is prevalent. While respirable silica exposures have been implicated in many cases, the available dust monitoring data from mines shows no explanatory trends. One possible factor could be differences in the relative toxicity of silica particles based on their surface condition. Previous research has indicated that particles with occluded surfaces (e.g., by a thin layer of clay) may be less toxic than those with non-occluded surfaces. However, this dust characteristic has not been investigated before now in central Appalachian mines. In the present study, 18 respirable dust samples from seven central Appalachian mines and two northern Appalachian mines were analyzed to assess the relative occurrence of surface-occluded silica. Results showed that the dust from central Appalachian mines actually had higher fractions of occluded silica, which may be due to extraction of large amounts of rock strata along with the coal. However, the central Appalachian mines also more silica particles overall (i.e., occluded + non-occluded) in terms of total number percentage of respirable particles.INTRODUCTIONResurgence of occupational lung disease among US coal miners, especially in the central Appalachian region, has been observed since the late 1990’s (Gibson, 2016; Zosky et al., 2016; Suarthana et al., 2011; Gamble et al., 2011; Antao et al., 2005; Attfield & Sexias, 1995). In addition to increased prevalence of simple Coal Workers’ Pneumoconiosis (CWP, or “black lung”), the prevalence of severe and rapidly progressive disease has risen dramatically (Almberg et al., 2018; Blackley et al., 2018a, 2018b, 2016, 2014; Graber et al., 2017; Cohen et al., 2016). While exposures to respirable silica have long been known to cause or play a role in diseases such as silicosis or progressive massive fibrosis (PMF), which is conventionally considered as the most advanced form of CWP, it is unclear whether silica is the only culprit in the recent outbreak of severe disease. Indeed, as disease rates have risen, both total respirable dust and silica concentrations generally appear to have declined since the late 1980s, based on regulatory monitoring data in the most affected mining districts (i.e., MSHA coal Districts 4, 5 and 12, which cover central WV, eastern KY and southwestern VA, and southern WV, respectively) (Figure 1). Of course, the latency of disease can vary and may be or more 10 years, but many of the most recent cases are likely to have resulted from exposures that occurred since the late 1980s."

Jan 1, 2019

This paper details a brief history of the Australian gold industry from the 1980s gold boom to the present day, highlighting an industry characterised by innovation in plant design and junior companies prepared to "have a go", in contrast to the conservatism of many larger mining companies. Design flexibility, the innovation of new processes, the preparedness to exchange "process know how" and technology singularly differentiated the gold industry from other sectors during the 1980s to the present. The introduction of two stage crushing, semi autogenous (SAG) milling, and pebble crushing, mill innovations, carbon in pulp (CIP) and carbon in leach (CIL) and the North Kalgoorlie screen etc were all exciting changes in the industry.

Jan 1, 2011

By J. R. Donald, K. Scholey

"Nickel has been mined and processed from the Sudbury basin for over 100 years. During this period, the process has evolved into what is one of the largest and most complex mining and metallurgical facilities in the world. This paper will describe the geology and mining of the Sudbury basin as well as the Copper Cliff metallurgical flowsheet circa 2005, including:•,Clarabelle Mill,•,The flash smelting furnaces,•,The bulk converters,•,Matte casting, separation, and processing•,The carbonyl refineries•,Carbonyl residue processing•,Copper processing•,Sulphur productsThe challenges of today and the opportunities for the future are discussed."

Jan 1, 2005

By John N. Ludden, Maurice Rive, Hillar Pintson

"Quelques soixante-dix-sept plutons présents dans la Sous-Province de Pontiac et dans la partie centrale de la Sous-Province de I’Abitibi ont fait I ’objet d’une reconnaissance systématique. Ils ont été regroupes en huit suites plutoniques majeures et trois suites mineures à partir de critères géologiques et petro logiques. Parmi les suites majeures, quatre représentent I' activité intrusive la plus ancienne dans la région. L’une d' entre e/les est représentée par deux complexes anorthosito-gabbroi' ques lites et les trois autres comprennent les orthogneiss dioritiques a leucotonalitiques et les intrusions dons la composition varie de diurétique et granodioritique à leucotonalitique. Leur mise en place peut être pretectonique a syn ou tarditectonique; certains plutons sont synvolcaniques. Quelques data/ions U! Pb effectuées à propos de ces roches donnent des âges s' étalant entre 2 718 et 2 694 MA. Les données géochimiques indiquent la présence des deux lignées magmatiques, tholemique et calcoalcaline bien qu’il n'y ait aucune évidence de relations entre elles dans I' espace et dans le temps. Ces suites magmatiques différentes peuvent provenir soit d’une croute tholemique impliquée dans un processus de subduction soit directement du manteau.Les trois autres suites majeures comprenant des monzodiorites, des granodiorites et des monzonites ainsi que les deux suites mineures comprenant des syenites correspondent à un évènement intrusif plus jeunesse déroulant entre2 694 et2 680 MA. Ces roches sont syn, tarti a post tectoniques et sont enrichies en alcalins, Ba, Sr et terres rares legeres par rapport aux quatre suites précédentes. Leurs caractères chimiques prop res suggèrent qu' e/les proviennent d' une source différente par rapport à celle precedemment citee.La derniere suite plutonique majeure correspond a un monzogranite leucocrate, riche en pegmatite, également syn a tard tectonique, dont I' age n' est pas connu avec précision. ll représente le seul granite ""vrai"" de la région et dérive d’une anatexie soit des meta sédiments soit des granodiorites-tonalites plus anciennes. La troisième suite plutonique mineure correspond a quatre stocks de granodiorite porphyrique qui n’ont pas été étudiés en détail.ABSTRACTSevenly-sevenplutons have been identified in the east-centra/part of the Abitibi Subprovince and adjacent Pontiac Subprovince. These have been subdivided, on the basis of geological and petrological criteria, into eight major and three minor plutonic suite. Four of the major suite, which represent the oldest intrusive activity in the area, range in composition from dioritic-leucotonalitic orthogneisses to diorite-granodiorite/leucotonalite and include two layered anorthosite- gabbro complexes. Their time of emplacement ranges from pretectonic to syn-late-tectonic and some plutons are synvolcanic. U-Pb zircon ages for these rocks range from 2 718 to 2 694 Ma. Geochemical data indicate the presence of both calc-alkaline and tholeiitic magma series for these rocks although there is no evidence time and space relationships between the two. The different magma series also suggest the derivation of these rocks from two sources, either from subduced tholeiitic crust or directly from the mantle. Three major monzodiorite-granodiorite, monzonite, and two minor syenite suites comprise a younger inlrusive event ranging from 2 694 to 2 680 Ma in age. These rocks are syn-, late- to post-tectonica and, compared to the above four plutonic suites, are enriched in alkalis, Ba, Sr and light Rare Earth Elements.Their distinctive geochemistry suggests that these rocks were derived from a different source region than for the older plutonic suites. The remaining major plutonic suite consists of leucocratic, pegmatite-rich, monzogranite-granodiorite. These rocks are also syn- to late-tectonic but their ages are not known with precision. They are the only ""true"" granites in the area and were derived by the partial melting of either older"

Jan 1, 1990

By N. L. Richards

In manufacturing for the 21st century, the first company to market often leads the pack in product development and sales. In this respect, manufacturing processes play an important role in transforming “raw materials” into a product(s) for sale to a customer. Thus it can be seen that upfront modelling of a design concept, or modelling of manufacturing processes in a plant, can play an important role in effectively ensuring the overall design and manufacturing route is carried out in an expeditious manner. In the paper various scenarios are considered with respect to modelling the microstructure and/or process, in various manufacturing processes. Also considered are the effects of service condition on the manufactured product in terms of creep and fatigue.

Jan 1, 2010

By W. E. Davies

"This paper is the sequel to that on Developments in Sintering Efficiency delivered by Davies and Mitchell at the International Ore Dressing Congress, Stockholm, 1957. Attention is drawn to the fundamental concept of sintering as a heat transfer process, in which the ignition heat is continually transferred onward through the bed as a heat wave. By its passage, this heat initiates endothermic 'changes, such as carbonate decomposition, whose energy requirements are supplied by the combustion of the fuel contained in the bed.Ideally, the heat wave should be generated by the ignition hood followed by the pre-heating of the incoming air. The fuel content of the bed should be no more than the theoretical quantity needed to balance the endothermic changes. In practice, the heat wave is seriously short of energy and this is offset by excess fuel in the bed. As a result, sinter quality suffers, more return .fines are produced, and fuel is wasted, a loss of efficiency which could be avoided if the fundamentals of correct ignition were more widely appreciated.Sintering speed, otherwise heat wave velocity, is a function of the rate at which the incoming air acquires .heat from the cooling sinter and imparts it to the unburned feed below the combustion zone. It is thus a function of rate of air flow and so depends on bed permeability>. Ways of• improving and maintaining permeability at the maximum consistent with thorough sintering are discussed, particular reference being made to taconite concentrates. The possibilities of recrystallizing refractory ores into forms more amenable to physical concentration techniques by sintering are visualised, very little expenditure on heat energy being required when the process is operated near the ideal conditions."

Jan 1, 1960

By J. Peck, F. Brackebusch, M. Scobie

"A number of alternative strategies exist to improve narrow orebody stope productivity and safety through mechanization. Particular attention is given to one of these: the development of an in-stope mining machine. This paper summarizes those characteristics of vein orebodies in Canadian mines which are considered to govern such mining machine design. It then reviews past and current attempts to develop hardrock mining machines which could potentially be applicable to narrow stope widths.IntroductionSerious interest is mounting to exploit new technology in the development of methods and machinery to stope narrow, hardrock, orebodies. The motives relate not only to the foreseen need to maintain or reduce production costs, but also to considerations of manpower availability, safety, ground control, ore recovery and dilution. This also follows the demonstrated success of technology application in larger metal orebody stoping, where machine development has been seen to lead to improved productivity as well as the future prospects of continuous mining systems and eventual automation, e.g. ITH blasthole drill development and bulk mining. This paper deals in particular with machine design for ore fragmentation in narrow, hardrock orebodies. It is considered that such machine design closely interacts with the over-all stoping method design and that both require consideration in parallel to ensure success in mechanization."

Jan 1, 1990

By Luke Evans

What are Best Practices? What are Bad Practices? Who Uses Best Practices? Why Bother? Acceptability Guidelines Published Best Practices Published Bad Practices Additional Best Practices Some Best Practices for Low Grade Deposits Interpretation Guidelines Big Bear Gold Deposit Example Conclusions Questions

May 1, 2013

Overview n Why we audited the IRS n How we did it n What we discovered n What we learned n Where we are going next The unbroken chain of safety The Internal Responsibility System (IRS) The network of roles and relationships in a workplace, through which everyone works with mutual commitment to reduce or eliminate hazards.

May 1, 2003