Search Documents

By N. Novikov, M. Jastrzebski, N. Kryzhanovskaya, D. Shevchenko, I. Kapran, N. V. Novikov, T. Koehler, B. Zaporozhets

"The PFK FeNi Smelter was re-commissioned by Solway Resources in 2002, ending a long period of economic decline in the adjacent town. In 2009 Hatch was retained to design, supply and install a custom furnace crucible that would accommodate a capacity increase from 34 MW to 40 MW and increase campaign life through binding and cooling technologies, as part of ongoing improvement efforts. The involvement of PFK personnel was critical to the successful integration of the new furnace technology with the existing process and operational practice. The furnace upgrade project was completed in 18 months during 2010 – 2011. Since start-up, the furnace has exceeded production expectations, operating successfully at 42 MW.INTRODUCTIONAfter ceasing operations in the 1990’s, the Pobuzhsky Ferronickel Combine (PFK), located in central Ukraine, was stripped of useful equipment and deteriorated while dormant. The surrounding town experienced a period of economic decline throughout the 1990’s. Solway Industries purchased the complex in 2002 and began a systematic incremental program to re-commission the smelter using both local expertise and specialists from other parts of the former Soviet Union. This led to the re-birth of PFK as a successful toll-smelting complex, and a renaissance for the surrounding economy.As part of the continuing improvement program, PFK approached Hatch in 2009 to study the possibility of a capacity expansion from 34 MW to 40 MW. It was decided, based on the results of the study, to design and install a custom furnace crucible integrating the unique PFK FeNi process with modern Hatch furnace technology. This novel approach had many benefits, including: maximum re-use of existing furnace components (off-gas, feed equipment and transformers), minimal impact on upstream and downstream equipment and building structure, and the retention of a familiar operating regime. The latter was a key factor in the success of the project, as it allowed the extensive operating expertise of the PFK staff to remain highly relevant to the upgraded furnace. This led to minimized capital investment, a rapid start-up and no significant operational challenges switching over to the new equipment incorporating Hatch furnace technology."

Jan 1, 2012

By A. McLean, W. Q. Chen, W. Yan, M. Barati, Y. D. Yang

In order to maximally remove the harmful impurities phosphorus and reduce the loss of valuable elements from Si-based alloy for production of solar-grade silicon, thermodynamic properties of the Si-based alloy were studied. In this work a new model, the Molecular Interaction Volume Model (MIVM) derived from statistical thermodynamics, was successfully used in the Si-based and Si-Fe-based alloy. The calculation started from binary Si-Fe, Si-P and Fe-P systems, then the thermodynamic parameters of ternary systems could be derived based sub-binary systems. Using the activity coefficients of the elements in the Si-based alloys and the saturated vapor pressure of the pure substance of the components, mass fraction of P during vapor-liquid equilibrium can be calculated. The calculated thermodynamic parameters were compared with experimental data available in different publications, and it is found that the thermodynamic parameters calculated using MIVM model are in good agreement with the measured results. The calculated result shows that the mass fraction of phosphorus during vapor-liquid equilibrium of Si-Fe-P melt increases with the increasing phosphorus content and decreasing temperature. This is an important direction for experimental practice in vacuum or low-pressure EML refining of ferrosilicon for potential production of solar-grade silicon without significant vaporization loss of valuable element.

Jan 1, 2015

By Timothy R. Eby

"The Wabush Mines project was formed in 1956 to develop a large iron ore property in Western Labrador. The town of Wabush along with the mining and concentrating facilities are located 640 air miles from Montreal, and 734 air miles from St. John's. The operation has been in production since late 1964.While mining and concentrating operations are located in Labrador, the pelletizing facilities are situated 275 miles south at Sept-Iles, Quebec. Dedicated in 1965, Wabush produces six million tons of high quality iron ore pellets annually. The company employs 1, 550 people at Wabush and the Pointe Noire plant at Sept-Iles.Wabush Mines is an unincorporated joint venture of three companies -The Steel Company of Canada, Dominion Foundries and Steel Ltd. and the remaining 58% by the Wabush Iron Co. Ltd. Wabush Iron Co. Ltd. is in turn owned by six companies: The Youngstown Sheet & Tube Company, Inland Steel Company, Interlake Inc., Wheeling Pittsburg Steel Company, Finsider International S.A. and Pickands Mather & Company which is also managing agent.The town of Wabush is set in a remote part of Northern Canada accessible only by rail and air transportation. But this in no way has hindered the growth and development of the area. Modern housing units, shopping facilities, airport and of course, recreational facilities are all patt of every day living amenities, an accepted aprt of southern communities, but quite unique for northern isolated mining localities."

Jan 1, 1978

By Daniel D. M. Adams

Over the last 100 years industry in general has been trying to advance the ability to maintain systems through management processes. Mining has looked to utilize onboard data systems in our mobile mining fleets to compliment these processes. Combining the two concepts build the concept that Rio Tinto refers to as asset health. These programs can generate a cost shift between $20,000 and $100,000 per piece of equipment annually. Even with the documented savings many operations struggle to justify the systems, why?

May 1, 2011

By E. R. Packer

"The mill of Anaconda Britannia Mines is located on the eastern shore of Howe Sound, approximately 32 miles north of Vancouver, British Columbia. The mill has a daily capacity of 3400 to 3500 tons and at the present is treating chalcopyrite-pyrite ore from which only the copper mineral is concentrated. For a clear conception of concentrate filtering and shipping practice at Britannia perhaps a bit of past history should be related.For many years the mill concentrated copper and zinc minerals and intermittently a pyrite concentrate was produced. It was general practice to ship copper concentrate by towed barge down Howe Sound, across Juan de Fuca Strait and thence down Puget Sound to Asarco's smelter at Tacoma, Washington. Zinc concentrate was loaded in hopper bottom rail gondolas spotted on rail barges and towed to rail heads in Vancouver, thence by rail to Anaconda Reduction Works in Great Falls, Montana. Most of the pyrite produced was shipped by ocean freighters to Japan and Taiwan with an occasional barge load of 2000 to 4000 tons to nearby customers in Vancouver and the state of Washington.In recent years, because of smelter shut-downs for one reason or another, mostly strikes, a considerable amount of copper concentrates has been shipped by ocean freight to Japan and in 1971 several lots were loaded in gondola cars and shipped by rail to the Anaconda smelter in Anaconda, Montana, because Asarco's smelter was forced by municipal and state anti-pollution laws to limit the amount of S02 emission from the smelter stacks. Zinc concentrate production was halted in the early part of 1Y70 because of zinc depletion in the ores and pyrite production was stopped in May, 1971, because of a lack of markets.Filter equipment in the Britannia mill consists of conventional disc vacuum filters and reciprocating vacuum pumps. The copper concentrate filter was installed in 1923 as a 6 x 8'6"" American disc type manufactured by United Filter Corporation, The zinc concentrate filter, now converted as a spare for copper concentrates, is also a 6 x 8'611 American disc manufactured by Traylor Engineering and Manufacturing Company and was installed the same year. Formerly, there were, in addition, two 4 x 6' disc filters for pyrite and two 6 x 6' disc filters to de-water bulk flotation concentrates ahead of the regrind mills. Installed vacuum pumps were two Ingersoll Rand 22"" x 811 and one 22"" x 9"". One of the smaller machines has since been scrapped.At the time of the writer's transfer to Britannia in 1965, the entire filter system was operating as a unit using two vacuum pumps and a common filtrate tank with a 2"" SRL filtrate pump for five operating filters. The regrind and pyrite filters were in continuous operation and the co11p('r concentrate filter alternated with the zinc concentrate filter because both copper and zinc concentrates were transp0rted to storage by the same conveyor belt."

Jan 1, 1972

By R. E. Jones

"INTRODUCTIONCominco Limited, one of the free world's largest producers of lead and zinc having majority ownership in Pine Point Mines Ltd., operates a mining and concentrating complex on the south shore of Great Slave Lake in the Northwest Territories. The mine was developed in 1963-64 and commenced operation late in 1964 with the direct shipping of high grade ore. The concentrator started production in November 1965 at a design throughput rate of 5,000 T.P.D.In 1968, the Company acquired the mining rights to a large ore body located to the east of the Pine Point claims and subsequently an expansion program at the concentrator raised the throughput rate to 8,000 T.P.D. The expansion included a third grinding circuit and additional flotation capacity. The flotation capacity took the form of a completely separate circuit from the existing flotation plant. In 1972, the zinc flotation circuits were modified to include two additional stages of cleaning. This change concluded the ""Pre-Consolidation Flotation"" circuit at Pine Point.In considering these modernization programs of the flotation section of the concentrator, the philosophy was to utilize the largest available machine having proven and modern technological changes. With the advent of the large capacity machines available in the late 1970's, it was considered a suitable time to revamp the entire flotation circuit at Pine Point in 1979. The Circuit Consolidation Project was developed to meet this requirement."

Jan 1, 1982

By D. M. Wyslouzil

"This paper was prepared for presentation at the 16th Canadian Mineral Processor's Annual Meeting, Ottawa, Ontario, Jan. 17 to Jan. 19, 1984.This paper gives an account of the development of treatment procedures for the differential flotation of refractory copper-zinc ores. Special references are made to the effectiveness of various zinc depressants and their combinations.Studies carried out on refractory copper-zinc ores demonstrated that conventional zinc depressants such as cyanide and zinc sulphate were not particularly effective when secondary copper minerals were present in the ore; the flotation activity of sphalerite was enhanced in the presence of cyanide.Among the various zinc depressants evaluated, the following depressant combinations were found most effective: Zn(OH) 2-S02 , 802-CaO, Na2S-Na2S03-S02, Na 2 S-S02 and Na 2S-S0rDS22.The practical application of any of these systems depends on the type of ore treated and other conditions such as pH, levels and points of collector and depressant additions.In this paper the effect of each depressant combination on different ores is described with reference to the selection of collectors."

Jan 1, 1984

By Chris Brown

"The Island Copper plant was designed and built by Fluor Utah Ltd, in conjunction with Utah design staff, Originally designed to treat 33,000 tons/day (t/d) of ore, the current average milling capability is 38,000 t/d (Nov'74). The first of six semi-autogenous grinding lines was brought on line in October 1971, startup of the remainder being governed by equipment delivery schedules.The summer of 1973 saw the start-up of an additional three ball mills, and attainment of the present production level. The current process flowsheet is shown in simplified form.CRUSHINGThe crushing circuit is relatively simple, comprising single stage crushing of the ore followed by screening to fine and coarse fractions.The crusher is a 54 x 74in. Allis Chalmers Superior Gyratory with a setting of 9-lOin., driven by a 500-hp motor. Trucks dump on three sides of a rectangular dump pocket. An 84in. x 20ft. link belt apron feeder draws crushed ore from a 250-ton surge bin below the crusher, discharging onto a 72in. wide inclined steel cord conveyor belt. A fixed splitter box at the conveyor discharge separates feed to two parallel Jeffreys 6 x 20ft. vibrating grizzlies for screening into +4in. and -4in. fractions. The fractions are collected on short reversible conveyors which feed the coarse and fine ore stacker conveyors. Trippers distribute ore to outside stockpiles adjacent to, and above, the concentrator grinding 'floor."

Jan 1, 1975

By Ralph Harris, Xia Qi, Frank Komsic

"Gold cyanidation kinetics which are often limited in commercial operations by the rate of oxygen dissolution from gas bubbles into the slurry, are discussed. Emerging technologies for improving the rate of oxygen dissolution are compared and the gas efficiency, energy use and operating performance of inverted cones and a device based on a jet diffuser are examined. The effect of solids loading is also reviewed and a relationship between operating parameters and the kilograms oxygen dissolved per kilowatt-hour is presented.Inverted cones are shown to create slurry settling problems at high gas flow rates and surface tension lowering agents are shown not to greatly improve the overall rates of oxygen dissolution.The novel jet diffuser technology operates at a range of gas to liquid ratios that improves its energy use over conventional technology and the performance of a number of designs are discussed.Gas efficiencies as high as 35% were observed with the novel diffusers at 40 cm diffuser immersion and are expected to increase at greater immersions. Energy use of 1.8 kg 02 I kWh were estimated for prototype full size diffusers operating at 100 cm immersion. Energy use of 3.S kg 02 /kWh is conservatively expected at 600 cm immersion.IntroductionGold ExtractionGold that can not be recovered by gravity separation can be recovered by either the Merrill-Crow process or the newer carbon in pulp (CIP) or carbon in leach (CIL) processes 1. Reductions in operating costs and improvements in gold recovery are central mill operating strategies. The present paper examines the potential for improvement that can be achieved in the gold cyanidation step of gold recovery. This paper introduces a number of emerging technologies and provides a basis for comparison of the performance. It shows that the basis for comparison of a particular technology depends on the type of gold extraction circuit employed and the type of reactants employed."

Jan 1, 1996

By A. Himsley

"There is an ever-increasing demand these days for efficient methods of removing metals from solutions especially for selectively recovering a particular metal from a mixture of metals in solution.Up until the mid l 930's the only methods widely practiced for such separations involved precipitation techniques or electrolysis. Both these methods have limitations and indeed can only be used for certain metals.It is only within the last 40 years or so when synthetic ion exchange materials became available that chemists in industry and universities have been able to apply ion exchange techniques to a wide variety of separations that not only would be impossible by precipitation methods but which are now achieved with much greater efficiency.Ion Exchange TechniquesIon exchange is a unit process that can be applied using either liquid ion exchangers or solid resin particles. Liquid ion exchange - or solvent extraction as it is often referred to - is used in a number of special areas dictated mainly by the nature of the separation.On the other hand, ion exchange resins are much more widely used and consequently a great deal more is known about their application to a variety of metal separations.In both systems there is a loss of the ion exchange material which in the case of solvent extraction results in hydrocarbons going to waste. The ion exchange resin systems lose resin in the form of small particles, referred to as ""resin fines"", and these are insoluble.The loss of liquid ion exchanger is due to the fact that it is slightly soluble in water and consequently the loss is a function of the volume of liquid with which it comes into contact and is not related to the amount of metal processed."

Jan 1, 1975

By V. Coffin, T. Cienski

"(Figure 1) Reagentized pulp enters into the column at about 1/4 of the distance from the top. Inside the column it meets with a downward flowing stream of water and with an upward flowing mass of air bubbles. Flotation takes place in this counter current system while at the same time fine gangue particles are washed off the froth before it reaches the overflow lip at the top of the column. The main operating features of the column flotation are as follows:a) No moving parts. Solids are kept in suspention not by an agitating action of a propeller but by settling down against the rising air bubbles.b) Wash water. Spray pipes are installed a few inches below the froth surface and deliver required volume of water. The purpose of this water is twofold:(i) it keeps in balance the flow of material through the column and(ii) it washes rising froth in the froth layer as well as removes unwanted fines attached to the bubbles at the lower flotation section. As a result the concentrate produced is of higher purity than in the conventional flotation. Column is characterized by very high up-grading. However, even temporary disruption of wash water supply results in a drastic drop of concentrate grate.c) Flow balance. (Figure 2) For the correct operation volume of the underflow (tail) is larger than that of the feed. The difference is made up by the wash water. This difference called bias is predetermined and ranges from some 4 to 15 USGPM depending on the size of the unit and process requirements."

Jan 1, 1981

By J. L. Bowlby

Introduction In the following discussion, boiler-feed and mine waters will be considered from the point of view of the problems arising from the chemical nature of the mineral and gaseous impurities they contain. The theories underlying some of these problems will be reviewed for the purpose of getting a clearer concept of the problems themselves. Certain terms of a chemical nature, necessary to the discussion, will be explained on the assumption that they are not generally familiar to mining engineers. Finally, an attempt will be made to correlate theory and practice, with the abject of establishing certain limits to factors relevant to the problems, and to show that these limits are justified by practical experience. The general problems occasioned by the presence of mineral and gaseous impurities in boiler-feed and mine waters are: (1) Scale formation and corrosion in boiler systems. (2) Corrosion of mine pumps and pump fittings. These will be discussed separately. Boiler Scale Typical analyses of waters available for use in steam power-plants are given in the accompanying Table (Table I). All analytical data are expressed in grains per Imperial gallon. The bicarbonates of calcium and magnesium in the raw waters are shown as normal carbonates in the Table. Substances in the first five rows constitute the encrusting solids. All the waters listed in Table I would be classified as 'very good' in the schedule of classification for boiler waters adopted by the American Association of Railway Chemists in 1887. In spite of this classification, however, the waters contain sufficient encrusting solids to cause serious scale trouble after prolonged evaporation.

Jan 1, 1934

By Peter Raziszewski

"A ball charge dynamics model is presented. Simulation results are compared with observed data showing good correlation. Based on the charge dynamics models, a liner wear model is presented along with some wear simulation results. Using the charge dynamics model with the liner wear model, it is possible to envision the predictions of mill power consumption as a function of liner wear. Further work is needed to validate the liner wear model.IntroductionFrom a process control point of view, industrial systems can be considered stationary or non-stationary. For example, the physical properties, such as geometric and/or material, of a system considered stationary do not change with time. However, this is not true for non-stationary systems such as those found in the mining industry where process dynamics are often violent with wear being an intrinsic process phenomenon.In this paper, a model for ball charge dynamics will be presented along with a description for liner wear. Simulation results for power draft prediction using the charge model will be compared with observed data. Further, liner wear results will also be presented."

Jan 1, 1997

By K. H. B. Wenzl

"Since the autumn of 1973, the world's attention was captured by the startling revelation that conventional energy supplies were not inexhaustible but were in fact quickly dwindling with future shortages imminent until lagging exploration and technology yielded additional energy sources to catch up with the spiralling increase in demand. This situation was precipitated by the Arab Oil Embargo and the resulting soaring cost of world crude oil.During the past few years there has been tremendous activity in the energy field which has had a direct impact on the Inca Metals Company Ontario Division operations. The company's reaction has been to establish an energy management program which will be described later in the paper. First, a brief description of the Inca Metals Company and the primary energy resources which are utilized will assist in putting the program into perspective.The Inca Metals Company, a unit of Inca Limited, is responsible for the production and sale of primary metals products worldwide. The company's operations in the Sudbury District include mines, ore concentrating plants, a Smelter, Nickel and Copper Refineries and an Iron Ore Recovery Plant. The Ontario Division also has a mine and concentrating plant in Shebandowan near Thunder Bay, and a metals refinery at Port Colborne. Inca is the largest producer of nickel in the non-communist world and is also a major producer of copper and platnium group metals."

Jan 1, 1978

By G. C. McKerrow

"Mr. G.C. McKerrow, Assistant Manager of Noranda Mines and formerly Smelter Superintendent attended the meeting to answer questions as to why smelters imposed penalties for too much zinc in a copper concentrate or too much copper in a zinc concentrate, etc.D.W. Bridges -Mattagami Lake MinesWhat limits do you set on zinc and lead in a copper concentrate?G.C. McKerrow - At Noranda, we allow 5% zinc free and charge 25 cents for every unit above that. For lead, it is 1% free and 25 cents per unit above that. Lead is a much more harmful impurity than zinc because it tends to recycle more in the smelter circuit and creates a greater health hazard in the plant.E. Thornton - Sullivan GroupWHat harm does fluorine do in the smelting process?G.C. McKerrow - Fluorine usually does not occur in harmful concentrations in non-ferrous smelters. Fluorides are present in exhaust gases in the aluminum and phosphate industries. If these fumes escape into the atmosphere, they may settle out on forage grasses in concentrations that are harmful to livestock.Thorton - Sullivan GroupI have asked this question other places and have been told that it is hard on brick linings and causes gold and silver to be lost up the stack.G.C. McKerrow - Almost any volatile constituent in a smelter charge will aid in carrying other metal values. To this extent it may be harmful.E. Thornton - Sullivan GroupMr. Tait mentioned before a smelter where they have a copper-tin ore and they pay for copper, tin, bismuth and silver but object strongly to indium in the concentrate. Why would this be?G.G. McKerrow - 1 can't see why indium would be a serious impurity. It does tend to concentrate in flu dusts and if you get enough of it you can recover it and sell it but I have never heard of anyone putting a penalty on it.Question - I once ran into a small copper mine in Peru that had cadmium in the copper concentrate but no zinc. The copper smelter charged a penalty for the cadmium. Why would this be?"

Jan 1, 1971

By Fathi Habashi

"A process is proposed for the treatment of phosphate rock for the recovery of uranium and the lanthanides. The process assures the production of phosphatic fertilizers without polluting the environment with radioactive material.IntroductionWhile many processes for uranium recovery from phosphoric acid produced by the H2S04 route are known and utilised commercially, little is known about uranium recovery from phosphoric acid produced by the HN03 route1. Advantages of the latter route are both the elimination of the gypsum disposal problem, and the possibility of radium disposal in a controlled way2. Further, the lanthanides originally present in the rock can be recovered if the nitric acid route is used; they will be mostly lost in the gypsum produced by the sulphuric acid route3. In the present work a scheme for the recovery of uranium and the lanthanides from phosphate rock without interfering with the normal route for fertiliser production is proposed using HN03 as a leaching agent. Attention was also given to uranium decay products and their separation so that they might not contaminate the fertiliser4. Further, an attempt was made to defluorinate the leach solution in order to upgrade the fertiliser and at the same time recover the fluorine5. Rapid analytical methods for the determination of uranium, radium, and lanthanides in phosphate rock were developed6,7."

Jan 1, 1997

By C. H. Dionne, J. A. Holmes, B. J. Huls

"Falconbridge Limited is presently developing flowsheet alternatives for implementation at the Strathcona Mill. The main thrust for change arises from the need to reject more pyrrhotite from the concentrate. To maintain appropriate levels of sulphur in the smelter concentrate, however, enhanced removal of non-sulphide gangue minerals must be realized. This could best be done in the Non-magnetics flotation circuit.Laboratory investigations were followed by an on-stream pilot test at Strathcona. The application of a column cleaner on the Non-magnetics concentrate resulted in significantly lower levels of fine gangue at equivalent sulphides recovery.This paper discusses the laboratory and pilot testing and results, with a focus on piloting. Also included is a discussion of the Strathcona Mill Flowsheet and the role of the Nonmagnetics flotation circuit.INTRODUCTIONFalconbridge Ltd. is currently developing means to reduce atmospheric sulphur dioxide emissions. One alternative is a reduction in the amount of pyrrhotite in Strathcona Mill concentrate, which reports to the smelter. Pyrrhotite in the Falconbridge ores contains an average of 39 percent sulphur and 0.64 percent nickel. By comparison, pentlandite contains an average of 33 percent sulphur and 34 percent nickel.A consequence of the rejection of pyrrhotite is a decrease in the sulphur assay in the remaining concentrate. This decrease causes downstream difficulties in the roasting process. Therefore, the content of non-sulphide gangue in the mill concentrate must also be reduced in order to maintain sulphur grades adequate for roasting. The resulting concentrate will have lower sulphur dioxide emissions while maintaining nickel production."

Jan 1, 1991

By C. M. Campbell

IN 1902, a famous Canadian geologist made the following statement : ?'From what we know row of the iron-ore fields of the Province, we may feel that Ontario is assured of a great future as an iron-ore producing country. Judging from the extent of the territory over which the newly discovered ranges have been found, Ontario should in the not far distant future take her place as one of the chief iron producers in the world". In 1905, an official of the Department of Mines said: "In ten years Canada will have b:ecome a great metallurgical country. You will see an iron industry in this Dominion larger than in any country in the world. Canada will yet furnish the world with its iron supply. It will be the same with iron as with wheat. A decade from now Canada will outstrip all other countries in wheat growing. The production of iron at a cheaper rate than it can be made elsewhere will cause Canada to take a similar position as far as iron is concerned". In 1924, a former President of the Institute, in arguing his claim for inconceivable mineral wealth in this country, stated as a "certainty" that iron-ore deposits on the scale of the ones in Minnesota would be found "again and again" in the Canadian Precambrian. In 1930, a Minister of Mines announced that "The country surrounding Churchill holds large deposits of valuable iron and coal", and he stated that, at that place, 'We will have an industry in iron that will compare with Pittsburgh". These statements are definite promises, just as definite and important as the statement "I promise to pay" on a note, and they are not fulfilled by casually stating, as is the habit, that someday we will work our low-grade iron ores. Nor are they fulfilled by stating, as is often done, "Oh, So-and-So did not mean that ' . Due to their importance and to the prominent positions held by the men who made these statements, they were widely circulated throughout Canada. They were taken at their face value, and on the strength of them and many more of the same kind in regard to our other resources we have planned and built, at huge expense, provinces, governments, civil services, railways, and other equipment. The reserves that were to justify these expenditures have not appeared. There has not been a ton of iron ore mined in Canada for many years, and important commercial reserves are unknown. We have built the mill, but adequate ore is lacking.

Jan 1, 1937

By William Shaw

Conditional simulation is now an accepted tool for managing ore block design at a number of operating mines. It provides a way to consider the quality of data, local continuity and economic risk in defining ore and waste across the cut-off boundary. In addition a computer based system can ensure consistency in making decisions to meet multiple criteria such as cut-off grades, minimum ore-block size and contaminant grade limits. The development of a procedure for using multiple criteria allows ore blocks to be defined using alternative strategies depending on the specific production requirements. This has introduced the opportunity to define ore blocks for different destinations based on their material types and opens the way for geometallurgical modelling to be incorporated into grade control.

Oct 1, 2009

By X. Gu

Mining operations, especially surface coal mines, have great impacts on the local ecosystem and the environment. However, it has been a common practice in mine design that the economic evaluation considers only the operating and capital costs, while the costs incurred due to ecological damage are left out. Such practice underestimates the total cost of mining and ignores the difference in ecological impacts between different mine design alternatives. With growing interest in sustainable development, the mining industry is under increasing pressure to operate not only based on economic and engineering principles but also on principles of sustainability. Therefore, estimating ecological costs of mining and considering such costs in the mine design process is an important step towards reducing ecological impacts at the design stage. The objective of this paper is to quantify the ecological costs of open pit coal mining and to demonstrate the influence of such costs on the ultimate pit design. The ecological costs of mining are estimated based on the areas and types of land damaged by mining activities and the carbon emission from energy consumption. Four major components of ecological cost are identified, namely, lost value of direct eco-services, lost value of indirect eco-services, prevention and restoration costs, and the cost of carbon emission from energy consumption. Necessary equations are given for estimating these costs. An algorithm is described for ultimate pit optimization in coal deposits with near-horizontal coal seams. A case study is presented in which the ultimate pits with and without ecological costs are optimized and compared to show the influence of ecological costs on the pit design outcome.

Aug 1, 2013