Search Documents

By Ish Grewal

The ACACIA Reactor - Introduction What is it? The Acacia Reactor is a fluidized bed high intensity cyanide leaching system. Purpose for its existence? The Acacia Reactor was developed to treat high grade gold concentrates generated from primary gravity concentration systems. Why intensively cyanide leach a gravity concentrate? Current secondary upgrading processes, such as tabling, create significant losses of fine gold that is initially recovered in the primary gravity concentration units. Additional benefits include improved security and a reduction in health hazards associated with calcining.

May 1, 2002

By Fidelis T. Suorineni

The Ashanti mine, located in Obusai, Ghana, West Africa, has been in production for over 100 years, and is currently the second largest single gold producer in Africa. The mine covers a concession area of 434 square kilometers with four main ore types: the quartz vein type, disseminated sulphide type, supergene sulphides and transition ore, and granitoids stock works (visible gold and quartz veinlets). Various mining strategies and methods have been employed for the mining of the narrow-vein ore at Ashanti. In recent years, the mine owner: Ashanti Goldfields Company Ltd. has embarked on a mine-wide expansion program to boost production to a target of one million ounces per annum. With the rapid depletion of its high-grade ore, a suitable mining method was required to produce a high tonnage at low cost to meet production objectives. This paper discusses how the Ashanti mine applied Canada experiences in mining technology to boost production, and the impact that the differing geological settings between the two countries had on the stope performance at the Ashanti operations. Experience developed at the Ashanti mine led to innovative modifications for stope layout and design methods in relatively poor ground conditions.

Oct 1, 2001

By D. E. Keeley

Introduction Gunite is a mixture of sand and cement applied to any surface by being shot by compressed air through a nozzle, where it is wetted just before leaving the orifice. The mixture is transported through a hose from a machine called a 'cement-gun'(l). Guniting of rock surfaces has been standard practice at the Mcintyre Porcupine Mines, Limited, for several years. Where used on walls and backs of cross-cuts; shaft stations, and other rock openings, as an air seal, gunite has eliminated the necessity of constant scaling to keep rock from falling from these places, and, under worse conditions, it has been used in place of timber supports. This has been of definite help in reducing costs, promoting safety, and minimizing fire hazards. During the past year guniting has been quite extensively used here in the rock head-works of the new internal shaft, No. 12, sunk from the 3,875-foot level. Gunite is at present being applied to the stations of that shaft well below a mile from the surface. This paper describes the method of guniting as carried out at the McIntyre, and illustrates how, by the adoption of this process, mining problems connected with scaling and loose ground have been completely solved. It is hoped that the information presented may stimulate discussion and assist in the use of gunite in this and other mines. The guniting method of applying cement was first developed by Carl E. Akeley (2), Curator of the Field Museum, Chicago, in 1907, and was exhibited in New York at the Cement Show in 1910. The museum was located in one of the old World's Fair buildings, built of roughcast and in bad repair. Mr. Akeley, who was a man of inventive nature, set about devising means of applying cement to repair the walls. The cement-gun was the result. Mr. Akeley was a taxidermist of note, a sculptor, and also the inventor of the Akeley camera. In his work, he was in the habit of using fast setting materials to build up foundations for statues, etc.

Jan 1, 1934

By P. Bousquet

Acid mine drainage (AMD) is a serious environmental problem that preoccupies the Canadian mining industry. Considerable amounts of money are spent every year in an effort to prevent or reduce the acid mine drainage phenomenon. AMD occurs when sulphide minerals (e.g., pyrite) contained in rock are exposed to air and water and subsequently oxidize to produce low pH water. This acid effluent has the potential to mobilize any heavy metals contained in the rock. Coating the sulphide minerals with silicates is a new promising technology to reduce AMD. Pyrite is treated with a solution containing H2O2, sodium silicate and a buffering agent. H2O2 oxidizes a small part of pyrite producing ferric iron (Fe3+) ions. These ions subsequently react with the silicate ions to produce ferric hydroxide-silica that precipitates on the pyrite surface producing a passive coating. This silicate coating can protect the grains of pyrite from oxidation. This paper presents a series of experiments that confirm that silicate coating can considerably reduce AMD.

Jan 1, 2002

By P. Toscano

The objective of this investigation was to determine how the losses of nickel, copper and cobalt in fayalite slags could be controlled for nickel mattes with iron contents below 5 wt%. Laboratory-converting and slag-cleaning experiments were carried out at 1250°C. Several variables were investigated during and after converting to help minimize the amount of nickel and cobalt that reports to the slag. The variables used were oxygen concentration in the blast, coke breeze addition and nitrogen injection stirring. In all the experiments, slag and matte co-existed. Coke additions during converting have little effect on the losses of nickel, copper and cobalt. In fact, coke additions retard the converting process by consuming some of the oxygen injected. On the other hand, coke additions and nitrogen injection applied after converting was completed resulted in decreased slag losses.

Jan 1, 2004

By P. Toscano, T. A. Utigard

"The objective of this investigation was to determine how the losses of nickel, copper and cobalt in fayalite slags could be controlled for nickel mattes with iron contents below 5 wt%. Laboratory-converting and slag-cleaning experiments were carried out at 1250°C.Several variables were investigated during and after converting to help minimize the amount of nickel and cobalt that reports to the slag. The variables used were oxygen concentration in the blast, coke breeze addition and nitrogen injection stirring. In all the experiments, slag and matte co-existed.Coke additions during converting have little effect on the losses of nickel, copper and cobalt. In fact, coke additions retard the converting process by consuming some of the oxygen injected. On the other hand, coke additions and nitrogen injection applied after converting was completed resulted in decreased slag losses."

Jan 1, 2004

By A. P. Schissler

Mining has several characteristics, uncommon in other business sectors, which pose additional challenges to the implementation or design of IT and management systems that use the information. Understanding these characteristics would improve the chances of successfully importing new information technology and management techniques to mineral producers. The most important characteristics that should be understood are workplace issues, the industry’s dual nature of being a continuous construction project using cyclical factory processes, labour challenges, workplace culture, information availability, integrative data elements, and the current technical education of mining engineers. These characteristics were taken into account in two applications of information technology and systems design at operating companies. The research and consulting projects focused on the development of an IT-enabled performance management system at several underground metal mines in Canada and an integrated data warehouse for surface mines spread throughout the United States and Latin America.

Jan 1, 2006

By Michael W. Russnak

Productivity and operating expenses are everything when it comes to judging how well your mine and company are doing. Stakeholders are always looking at these numbers and trying to understand if productivity is improving, if operating costs are trending downward and what you are basing your decisions on. o make improvements you first need to understand how you are performing. If you can?t get this basic information, you will never improve. You will not be able to make simple decisions related to maintenance, operations or production. Forget about planning, as you will only be guessing based on the numbers some stakeholder or your executive wants to see. The problem miners run into is not that the data doesn?t exist; it does, but typically it?s raw, it?s everywhere and its volume is huge. Today there is more on-board computing capability in shovels than we had on our desktops three years ago. Add other mobile equipment, plant systems and multiple OEM vendors to the equation and the challenge is daunting.

May 1, 2007

By Tao Long

Recently, the great amount of funds has been invested in the reconstruction of damaged infrastructure and house of subsidence area of coal mine and mine reclamation. This is a benevolent and popular work, which is highly praised. However, because of complicated collapse area problems in China, especially the less integrated control research in the collapse area of metal mine, and the technological weakness, how to effectively control the subsidence area, restore landscape and ecological environment, and utilize the abandoned mine land, are major issue related to the mining area of sustainable development. The research situation about the formation of metal mine collapse area at home and abroad is reviewed, and then the effect of the collapse area on the mine safety and ecological environment, the existing technical problems and development direction are analyzed. Lastly, the technical measures of the collapse area control and cooperative underground mining is put forward.

Oct 1, 2010

By C. Patel, George H. Hope

"INTRODUCTIONThe Hemlo area is located in Northern Ontario, some 350 km east of Thunder Bay along highway 17. Hemlo is Canada's largest, recent discovery of gold ore. Three companies, Lac, Noranda, and Teck are currently developing mines and processing facilities in the area. A combined milling capacity of approximately 10,000 tonnes per day will ultimately be available in the area. The gold yield will be between 750,000 to 1,000,000 ozs. per year. This will slightly more than double Ontario's gold production but only represents 2.5% of the total world gold production.Lac Minerals Ltd. is substantially committed to the gold mining business. Lac currently operates four (4) gold mines and mills and produces 300,000 ozs. per year. Lac's Hemlo development will put the company in the position of number one gold producer in Canada.The Lac Hemlo ore body has an estimated reserve of 37 million tonnes at 6.2 g/t. The mining will take place at an initial rate of 3,000 t/d commencing in the first quarter of 1986. The mine and plant will be expanded to 6,000 t/d in 1988. At this capacity, Lac will be the largest producer in the Hemlo area.1. GEOLOGYThe orebody is divided into two (2) zones for mining purposes. The 'A' Zone is to the east and dips to the Northeast from surface to 300 m below surface. This zone has a strike length of 250 m to 300 m at an average width of 20 m. The upperpart of the zone will be mined by open pit and the remainder from underground. The 'B' Zone, to the north west of the 'A' Zone, although lined up is not necessarily an extension of 'A' Zone. 'B' Zone has a known strike length of 600 m and is open to depth and along the strike. It is over 70 m wide in the core. This zone holds most of the property's known reserves. 'C' Zone with narrow gold zones is under exploration in the south west portion of the property."

Jan 1, 1985

By Godfrey MacDonald

"The East West Caribou deposit with an underground mine, concentrator and ancillaries is located 30 km west of Bathurst, New Brunswick. The Restigouche deposit, an open pit mine is 30 km west of East West Caribou. The ore will be trucked from the Restigouche site to the East West Caribou minesite.History:The East West Caribou ore body was discovered in 1955 and the subsequent metallurgical programme focused on producing a bulk sulphide concentrate. However, in 1966 a Mr. P.G. Kihlstadt of Anaconda did float a Copper-Lead concentrate and a Zinc concentrate. He also reported that as the grind became finer the recoveries improved. In 1968 the Mines Branch in Ottawa produced a Lead concentrate of 30 percent at a 60.5 percent recovery and a 52 percent Zinc concentrate at an 83.4 percent recovery.Laboratory testwork proceed the 1988 start up of our current concentrator and underground mine facilities. The concentrator was designed to produce a Lead ""rich"" concentrate and a Zinc ""rich"" concentrate which were combined to make a marketable Bulk concentrate. In 1990 the operation was suspended because of declining base metal prices, increasing smelter treatment charges, increasing operating costs and operating difficulties.The 1997 operating plan is to produce a Lead concentrate and a Zinc concentrate.The Restigouche ore body was discovered in 1989. The subsequent testwork done at Lakefield Research recommended the production of a Copper, a Lead and a Zinc concentrate. The ore reserve could not support a stand alone concentrator so the project was put on hold.Laboratory testwork was carried out at Lakefield Research to confirm compatibility of the East West Caribou ore and the Restigouche ore in their processing."

Jan 1, 1997

By J. I. Mathis

"The failure that was utilized for developing this model was a double bench-scale failure, approximately 20 m in height, in the Misery pit at BHP Billiton’s EKATI mine site. The bench that failed was excavated in biotite schist. Due to previous problems with bench-scale toppling failures, this bench was excavated with a 70° inclined, 30 m deep preshear. Upon exposure, the wall was very clean with half-barrels commonly observed from the pre-shear operation.In August 2003, a bench failure of about 1000 t occurred in this pre-sheared biotite schist (Fig. 1). Upon examination it was noted that the foliation that paralleled and dipped at 70° into the face when excavated was approximately horizontal at the top of the failure (Fig. 2). While the failure mode itself appears complex, the failure was apparently driven by three factors:• a low-angle, low-frictional strength fault or discontinuity at the base of the failure area;• water either contributed meteorically from precipitation and/or from permafrost melt; and• foliation planes providing a viable toppling geometry once toe block motion began to occur.The above details are illustrated in Figure 3.After considerable thought and analysis, a model was postulated for the failure.It is thought that the entire failure had been triggered by displacement of a toe block (Fig. 4). This toe block is bounded on the back by foliation, the bottom by a low-angle, lowstrength fault, and the front by the bench face. Water pressures behind the bench face developed forces on the block as can be seen in Figure 5. These forces were sufficient to induce block motion. As can be seen in the relative shear strength diagram in Figure 6, only a small amount of water is necessary in the face to initiate block displacement. Note that in this figure, a simplistic piezometric pressure distribution was assumed."

Jan 1, 2004

By D. Ingram

"PRIMARY DUST COLLECTOR A. 42,000 CFM James Howden Fan Z-6 Size 3650 Fan Dia 40"" HP 75It was found that the fan was not large enough to remove the air that was displaced by the trucks dumping. So it was removed and an enclosure was installed to isolate the gyro from the rest of the building.B. FANSJames Howden Fans Model RPM 3500 Series 357 FW HP 10These fans were installed when the first dust system was put into operation. It was found that the high RPM and extreme fan wear caused a major maintenance problem. These fans were replaced with Chicage Blowers Model SWS1 RPM 1180 Dia 36"".DRY CYCLONE COLLECTORS A.,Three four foot rubber lined cyclones. Four six foot rubber lined cyclones.All under flow. Water is controlled manually and gravity flows to a central sump box. From there it flows to the grinding circuit in the Mill.Cyclone under flow product runs between 100 and 200 tons of dust per 24 hours with a screen analysis 30% + 400.The cyclone under flow product is diluted to about 3 to 4%. Solids total gallonage approximately 400.B.,Elbair Wet Scrubber125 HP RPM 56042,000 CFM,Model PX861The Elbair collects the total product from the discharge. Of the Cyclone fans the under flaw goes to the Mill - the Elbair discharges stack goes to atmosphere.The Elbair wet scrubber had to be redesigned in order to keep it in service."

Jan 1, 1976

By P. W. Godbehere, B. W. Brooks

"This paper deals with the milling of slags from the Noranda Continuous Process, in the Horne Concentrator at Noranda, Quebec. The milling of copper slags, although novel in Canada, has been practiced in Japan, Finland and elsewhere for several years.In March 1973, the prototype Noranda Continuous Process furnace or ""reactor'' came on-stream, In this pyrometallurgical process (see Fig. 1), copper concentrates mixed with flux are smelted in a single furnace to form copper or a high grade copper matte, and slag. The conventional smelting processes of roasting, reverberatory smelting and converting have been incorporated in a single 17 ft. diameter by 70 ft. long steel cylindrical vessel (l, 2). The copper or matte is tapped from the bottom of the reactor into ladles and transferred to an anode furnace or to a converter. The slag is tapped into 40 ton capacity ladles, cooled, crushed, and conveyed to the concentrator. At the present time, the reactor is operated to produce matte. The matte slag* containing 4 - 6 per cent copper is milled using conventional ore dressing grinding and flotation equipment. A flotation concentrate assaying 35 - 40 per cent copper is recycled to the reactor. Crushing, conveying, grinding, flotation and tailing disposal equipment previously used for over 40 years for ore treatment has been modified to suit the requirements of slag milling. Slag milling is essentially the scavenger circuit of a pyrometallurgical process."

Jan 1, 1977

By Peter Mitschke, Friedrich Rosenstock, Heinrich Meiler

"The development of the Centrifugal Mill jointly by Chamber of Mines (Johannesburg) and LURGI GMBH (Frankfurt) had been described by L. Kitschen e.al. during the 14th IMPC at Toronto in October 1982. Further investigations, using a 55 kW semi-industrial mill, installed at LURGI's Research Laboratories, were concentrated on efficiency and wear in grinding.The test results showed, that efficiency increases when increasing the ball load between 60 and 80 % by volume. Furthermore, the efficiency is increased by speeding up the mill, thus increasing the centrifugal force to up to 14 times the force of gravity. Applying these findings to grinding of a Canadian iron ore spiral concentrate, a saving in grinding power of 30 % was experienced, when comparing with ordinary wet ball milling.Investigations of several shapes of the grinding chamber cross section and linings and several types of materials showed, that no increase of liner or ball wear will occur compared to conventional ball mills when choosing suitable lining patterns. 1. DEVELOPMENT OF THE CENTRIPUGAL MILLThe centrifugal mill was developed with the aim of finding a grinding unit that can operate at a higher power concentration than the conventional tumbling mills.LURGI felt the necessity for such a mill in connection with a hydrometallurgical process developed at the beginning of the seventies, which incorporated an activating grinding step as one of the essential process features. At that time, the Chamber of Mines in Johannesburg was investigating possibilities of underground wet grinding and preconcentration of gold ores aiming at a decrease of mining costs by reducing the quantities, especially for mines operating at depths up to 3600 m, by changing over from rope hoisting to hydraulic transportation systems. After the Chamber of Mines had initiated the development work on its own, in 1974 a cooperation between the two organisations was started."

Jan 1, 1985

By G. Winkel

Safety conditions in industry have greatly improved over time. However, around the world, in Canada, and in each province or territory, people are still the victims of serious industrial accidents. The increasing safety of people at work then continues to be an imperative in industry today.<p> So how do we achieve a workplace where no one gets hurt? Well, in simple terms, folks need to be protected from unplanned exposures to equipment or energy sources that can do harm. If you think about it, all of our efforts in loss management and safety should then be directed toward avoiding these uncontrolled events. And it works! Our safety performance over the years has enjoyed tremendous improvement due to this support for loss management and safety. We now explore best practices toward achieving that next step in safety improvement.<p> As shown following, a large combination of loss management activities act together to support safety performance. Many of these activities are interrelated and some people have described them as the ?inputs? into an approach or program for achieving safety. Using this description, it follows that the ?outputs? of the program are some of the advertised measures of safety we see around us today, such as injury frequency rates. <p> It is asserted that a leadership focus to regularly measure safety and loss management activites (so-called ?inputs?), as a basis for taking supportive actions to ensure their effectiveness, is the basis for safety results (so-called ?outputs?) that consistently achieve high standards of excellence.<p> The concept of managing input activities, as enabled by effective measurements, can significantly act to transform our focus and priorities in the workplace. Supporting input activities like strategies, plans, or procedures with our best efforts will get us to our intended goals. Tracking outputs alone will not.<p> Safety and production have traditionally been cast as competing objectives. When both objectives are mutually supported and considered, however, people will invent ways of doing work that support both safety and production, and any other business parameter. When done right, innovation through meaningful involvement of affected people in the workplace will support safety excellence in a manner that in turn improves business efficiency overall.<p> For a workplace to be safe, it then requires everyone?s help and participation to make it happen, a collaborative effort by management, leaders, and frontline folks with the power and responsibility to take appropriate action at every level in the organization. In this way, everyone becomes a leader in safety.<p> The achievement of commitment to loss management input activities by folks in the workplace is the basis for attaining safety excellence. A workplace founded on commitment supports a safety culture with a vision for safe work performance at outstanding or world-class levels of achievement.<p> One may ask if injury incidents will be eliminated with this commitment and focus on workplace safety? Well, despite our best efforts in this area, there is never a guarantee that things can?t go wrong. We are simply not perfect. There remains in our workplace complexities and unanticipated risks that can have disastrous consequences if not managed at every moment. And when it goes wrong, we need to know we?ve truly tried our best, and now we have more to learn so we can get even better. <p> That?s the challenge represented by the safety imperative, a challenge to take safety performance that next step, a fulfillment of our commitment to the moral obligation we have to each other?s safety. It?s an effort that will continually raise the bar of world-class safety performance achievement for future generations. It?s a legacy we can be proud to be part of.

Sep 1, 2004

Project Schedule ?Construction 2005 ?2008 (3 years) ?Operations mid 2008 ?2020 (12 years) ?Closure 2020 ?2023 (3 years) ?Post-closure monitoring Victor Economic Facts ?$982 million investment; ?$110 million already invested in the Project; ?1100 person years of employment in construction; ?375 full time positions during operations;

May 1, 2006

By S. Felderhof, W. S. Vaughan

"Over the years, it has been increasingly difficult for the minerals industry to raise the necessary capital for its activities. To alleviate this phenomenon, complete transparency and capital market efficiency is needed. Since a company’s mineral resources and mineral reserves base is an essential component to obtaining capital, reporting these assets must also be transparent and efficient. This must occur, however, at an international level given that mineral industry operations, and its financing, are international. To achieve this, an international committee (i.e. Australia, Canada, South Africa, the United Kingdom and Europe, and the United States) was formed and has been developing standards for the reporting of mineral resources and mineral reserves.The effectiveness of these standards, however, depends on adoption by the required regulators. Unfortunately, these standards have not been recognized by the U.S. Securities and Exchange Commission (SEC). Instead, the SEC adheres to its old standard (Industry Guide 7), making it increasingly expensive and difficult for international mining companies to obtain capital in the United States. Compounding the problem is the SEC’s influence over the current work of the International Accounting Standards Board and the International Organization Organization of Securities Commissions. These organizations are in the process of standardizing international accounting practices and international securities rules and regulations. Their current position may prevent adoption of the industry-developed mineral resources and mineral reserves standards which are internationally recognized."

Jan 1, 2005

By A. Akerman, C. P. O’Connor, N. Vayenas

"Stereolithography is a well-known rapid prototyping technique in the manufacturing sector. Essentially, it is a three-dimensional printing process that produces plastic prototype parts from standard CAD files. At present, Canadian mining companies are not fully aware of the potential of rapid prototyping techniques (RPTs) for their production and mine design systems. Mining engineers and geologists attempt to visualize and understand the characteristics and layouts of orebodies on computer models, and in cases where it is decided to develop physical models, the process is time-consuming, based on simplified constructions. RPTs, such as stereolithography, can facilitate engineers and geologists to quickly, and with satisfactory accuracy, visualize sections of orebodies and evaluate alternative ore extraction techniques using 3D solid models.The research discussed in this paper is carried out by the Laurentian University Mining Automation Laboratory (LUMAL) in collaboration with Inco Limited and the Integrated Manufacturing Technologies Institute (IMTI) of the National Research Council of Canada. The main objective with this research is to evaluate the applicability of state-of-the-art RPTs to underground hard rock mining systems. RPTs can play a significant role in accelerating the design and development process of mining systems."

Jan 1, 2006

By G. Winkel

"Safety conditions in industry have greatly improved over time. However, around the world, in Canada, and in each province or territory, people are still the victims of serious industrial accidents. The increasing safety of people at work then continues to be an imperative in industry today. In addition to protecting people, safety has been shown to make good business sense in any industry.The road to safety improvement is built on establishing a culture of safety that forms the basis for how work gets done in a company. Most importantly, an effective safety culture is built on the full engagement and participation of workers and leaders alike, who share in a vision for safe work performance where “no one gets hurt” and “everyone is a leader in safety.”Let’s learn together on how we can make a safety culture happen. The resulting bias for safety will ultimately save lives, and fulfills our moral objective to strive for safety excellence. IntroductionWe have the good fortune of living in democratic countries where freedom and the value of human life are key beliefs. These beliefs translate into the moral obligations and laws that we value and uphold in our society and life today.A minesite or workplace is simply a necessary part of our society where people earn a living. It is a place where our moral obligations and laws equally apply, a place where human life is of ultimate importance and value. In the early years of industry, this value has not always been evident. Take this description of a tragic accident reported in a coal mine on December 8, 1879:“Oliver Thompson, shaftman, aged 35— While taking wooden partitions out of a ventilation shaft, he fell off the work platform a distance of 100 yards, there did not appear to be anything unusual to account for this accident.”"

Jan 1, 2004