Search Documents

The paper deals with the taking of soundings in connection with coal mining operations under part of the Pacific Ocean adjoining John Darling Colliery.INTRODUCTIONIn the early days of mining in the Newcastle District there did not appear to be any definite law specifying the limits to which mine workings, other than certain borings, could extend under tidal waters.As time went on, a figure of 120 ft. was fixed as the minimum thickness of strata between the roof of the seam and the sea bottom; beyond this mining operations are disallowed. The laws relating to working coal under tidal waters are as follow:-The minimum width of pillars to be left shall be eight (8) yards and the maximum width of bords or other excavations shall be six (6) yards, but the lessee may at his discretion increase the minimum width of the pillars or decrease the maximum width of the bordsor other excavations so as to increase the general safety.The eight (8) yard pillars shall be left unwrought.In on-road of every pair of Winning-off or leading headings, a bore shall be kept going ten (10) feet in advance for the purpose of foretelling the presence of any fissure, wash-out, open joint, fault, dyke, or otherwise, and all winning-off headings shall be driven atleast one hundred (100) yards in advance of the working bords.The most accurate and trustworthy information shall be obtained by the lessee not only' of the depth and character of the ocean bed, river, lake, or estuary deposit, but also of the strata overlying the coal seam.When working under the ocean, strata shall be bored through and proved a minimum thickness of thirty (30) feet at the face of the leading headings or levels immediately such headings or levels are under the ocean, and...

Jan 1, 1947

By H Aral, L Malishev

The carbothermic chlorination of titaniferous materials such as rutile, synthetic rutile (SR), upgraded slag and ilmenite in a fluidised bed is an established commercial process. In this work, ilmenite sourced from the Murray Basin area of South Eastern Australia was chlorinated and an assessment of the chlorination characteristics of the ilmenite, in terms of pre-treatment, type of reductant and reaction time was made. Selective chlorination of Murray Basin ilmenite to remove Fe and Mn was achieved in this work. A synthetic rutile sample containing around 93 per cent TiO2, one per cent Fe2O3 and 0.5 per cent MgO was produced at a chlorination temperature of 1000¦C with around 25 per cent loss of Ti as TiCl4. Raising the reductant to ilmenite ratio in the chlorination reactions increased the amount of Ti chlorinated. However, complete chlorination of Murray Basin ilmenite to produce FeCl3 and TiCl4, was not achieved under the conditions used in this work. Pre-oxidation of Murray Basin ilmenite before chlorination had little affect on its reactivity, compared with æas receivedÆ ilmenite. In contrast weathered West Coast ilmenite chlorinated appreciably better than West Coast primary ilmenite, in terms of bed residues remaining and amounts of elements removed. The presence of large amounts of Mg and chrome spinel grains in the Murray Basin ilmenite used in this study are likely to make it difficult to chlorinate directly in a commercial chlorinator. However, this is not to say these ilmenites will be unsuitable for chlorination applications. Further work is needed in the separation of Mg and chrome spinel grains from Murray Basin ilmenites and the products resulting from these tests could then be assessed in terms of chlorination performance, so that further processing options can be explored.

Jan 1, 2000

Existing production facilities are constantly looking at ways to increase capacity. Many recent solutions have focused on the implementation of capital and infrastructure projects. It is accepted that capital expansions are frequently necessary for production gains; however, in many cases existing assets have the potential to deliver substantially better throughput than they are currently achieving. By focusing on automation of production control systems, production reporting and business processes substantial gains can be achieved utilising existing assets. This potential can be realised quickly and has been proven across several sites and industries. In the Pilbara region of Western Australia throughput gains of between two per cent and 25 per cent (translating to millions of tonnes per annum) have been achieved from existing assets using the methodologies discussed. The improvement process involves evaluating the entire production chain from the time the ore arrives at the plant to the time it is dispatched. A technical evaluation of the performance of the control system and plant automation interfaces to upstream and downstream processes is conducted. The relationship of these processes to the business systems and the human interface to the systems is reviewed to ensure a complete picture of the system is understood. Technical evaluation targets include: individual equipment operation, the engineering level of control systems, feed controls, etc; managing recirculating loads, surge capacities, dynamic inventories as well as management of in-feed systems and integration into yard and out-feed systems; and communication flow between control and other systems, data alignment between rail and shipping schedules, yard systems, sales systems and maintenance systems including such fundamentals as truck dispatch links to plant control. In parallel with the technical evaluation, business system evaluation takes place, including analysis of the operational systems, methods and personnel.

Jan 1, 2007

By F R. A Jorgensen, G W. Jensen

A pilot scale experimental investigation of the condensation of zinc vapour from smelter off-gases was performed in conjunction with a mathematical modelling study of the system. The work investigated the feasibility of using the high heat and mass transfer rates associated with a fluidised bed to condense zinc directly from smelter off-gases containing zinc vapour. Of particular interest was whether zinc would revert to zinc oxide during the process of condensation, and whether a zinc fog would form and be carried out of the condenser. A 0.1 m diameter fluidised bed condenser was mounted on the top of a 200 kVA DC electric arc furnace in which mixtures of vapours and gases were generated at 1150 - 1300¦C. The gas/vapour mixtures investigated included Zn/N2, Zn/N2/CO/CO2 and Zn/N2/H2/H2O. Greater than 90 per cent of the zinc was deposited on the zircon sand bed of the condenser, and there was no sign of zinc oxide formation, suggesting that the rate of heat transfer was faster than the reaction rate for zinc oxide formation. There was also no evidence that fog was being formed in the condenser. Using the methods of Kunii and Levenspeil (1991), a mathematical model was developed to predict the behaviour of the fluidised bed condenser. The model enabled the distribution of gas/vapour temperature and bed temperature to be determined as a function of distance from the condenser inlet. Similarly the partial pressure of zinc vapour in the gas mixture, and hence the mass transfer rate of zinc to the particles, was determined. Experimental data allowed validation of the predicted bed and gas/vapour temperatures.

Jan 1, 2000

Mispah form (FAO: Lithosol) soil contaminated with >380 000 mg kg-1 creosote was co-composted with sewage sludge and poultry manure for a period of 19 months. The soil was mixed in a ratio of 1:1 (v/v) with wood chips to improve aeration. The soil-wood chips mixture was then mixed in a ratio of four soil-wood chips mixture: one compost material (sewage sludge or poultry manure). Compost heaps were set up in triplicate on wood palettes overlaid with double layers of nylon straw bags. Control experiments, which contained the contaminated soil-wood chips mixture without sewage sludge or poultry manure were set up in triplicate. Moisture, temperature, pH, ash content, C:N ratio of the compost and the creosote concentration of the soil was monitored monthly. The concentration of selected creosote components in the soil was also determined at the end of the incubation period. Temperature was observed to rise to about 60¦C in the poultry manure and about 58¦C in the sewage sludge within two months of incubation, while temperature in the control fluctuated between 15¦C and 35¦C throughout the incubation period. Creosote concentration in the control was reduced by 17 per cent at the end of the incubation period while concentration of creosote in the sewage sludge and poultry manure compost was reduced by about 99 per cent. The percentage rate of creosote reduction in the poultry manure compost was initially lower than observed in the sewage sludge compost. However, the reduction rate became similar towards the end of the treatment period. The concentrations of selected creosote components were reduced by about 100 per cent within the same period. Respiration of compost microorganisms and counts of microbial populations showed that microbial activity correlated with reduction in creosote concentration.

Jan 1, 2004

Basicity(aO2−) has been known to affect the physicochemical properties of molten slags in the metallurgical processes. However, because of the impossibility of direct measurement of single-ion activity, various indirect measures such as capacity, redox equilibrium of transition metal ions, activity of basic oxides, and (theoretical) optical basicity have been proposed; but these basicity measures have been restricted within slag systems and the interaction between measuring elements and slag components has affected the quantitative estimation of slag basicity. Recently, since it was reported that solubility of noble metals in molten slags could be an indirect measure of basicity, the influence of slag basicity on the solubility of platinum and silver has been reported. The reaction mechanism of platinum dissolution into basic slags has been reported, whilst that in acidic slags has not (Nakamura and Sano, 1997; Sano and Nakamura, 1997; Nakamura et al, 1998). Richardson reported that the solubility of metals such as cupper, gold, silver, and lead in the CaO-SiO2-Al2O3 slag was presumably dependent on the atomic radius and the accommodation ability of the silicate network (Richardson, 1974). Swinbourne and You measured silver solubility in the Na2O-SiO2 slag over a wide range of oxygen partial pressure and suggested that silver would be present as both Ago and Ag0.5 in the slags (Swinbourne and You, 1999). For brevity, these previous works discussed the dissolution mechanism of silver into the slags based on the existence of silver as a neutral or molecular species. However, because the almost chemical reactions occurring in the slag are affected by the basicity, the reaction formula with O2- ion is required based on the ionic characteristics of the slag such as desulphurisation and dephosphorisation reactions as given in Equations 1 and 2, respectively.

Jan 1, 2000

By J G. Petrie, H von Blottnitz

The selection and design of process options to deliver outcomes consistent with sustainable development requires simultaneous consideration of multiple objectives, within a climate of uncertainty û including the environmental and social aspects of technology management in addition to the technical and economic aspects of such. An issue of particular relevance in primary metal production is the deportment of minor and trace components within orebodies, products and wastes and the implications of such deportment for eco-efficiency û in particular, the long-term environmental impact of solid waste management practices. The identification of opportunities to enhance recovery of valuable by-products and simultaneously improve the environmental acceptability of final waste output requires a clear understanding of the distribution of the relevant ore components, which results from the choice of processing route and unit operation efficiency. This is challenging, given that process streams generated during primary metal production are generally poorly characterised and the behaviour and deportment of trace to minor and trace components is not well understood. This paper demonstrates how current data gaps and inconsistencies can be systematically addressed through the meaningful reconciliation of empirical plant data with a fundamental understanding of the mechanisms and parameters influencing element behaviour and deportment during the formation and subsequent beneficiation of mineral ore deposits. On this basis, quantitative distribution data and a comprehensive and comprehensible inventory of unit process inputs and outputs as a function of ore compositions and processing technology options can be generated, which is consistent with early design stage information requirements, both in terms of detail and accuracy, ie is æfirst-orderÆ in nature. This predictive approach to element distribution during primary metal production provides decision-makers with key information in the early design stages of a project (in terms of developing processes within the context of sustainability), whilst simultaneously guiding further data collection and environmental impact prediction studies.

Jan 1, 2006

High-sulphidation (HS) gold, silver and/or copper deposits are generated in both the epithermal and the upper parts of the underlying porphyry environments over vertical intervals of up to 2 km. The HS deposits are generated in advanced argillic lithocaps, which are products of the absorption of acidic magmatic volatiles by voluminous groundwater systems. Mineralisation styles in HS systems reflect depth of formation as well as the interplay between structural, lithological and hydrothermal parameters. The deep parts of HS systems, at depths of >1000 m, are typified by disseminated copper¦gold mineralisation comprising digenite, chalcocite and covellite in pervasive advanced argillic as well as underlying sericitic alteration. In highly telescoped systems, suchmineralisation may overprint porphyry stocks and associatedquartz-veinlet stockworks. Intermediate levels of HS systems commonlycontain fault-controlled copper-gold mineralisation, typically as enargite in bodies of vuggy residual quartz, silicification and/or massive pyritic sulphide. The shallow parts of HS systems, at depths of The exploration focus is on four principal HS mineralisation styles: 1. copper (eg Chuquicamata, Monywa) or copper-gold (Wafi) in thedeep porphyry-hosted parts of systems preferably, in the case of thelatter, where supergene oxidation is limited and, hence, flotationmay be used for metal recovery,2. copper¦gold-bearing replacement mantos and pipes hosted bycarbonate wallrocks in the deep parts of systems (eg Bisbee),3. high-grade gold in late-stage veins or hydrothermal breccias thatoverprint the intermediate to shallow levels of systems (eg El Indio,Goldfield), and4. large, bulk-mineable gold deposits in the shallow parts of systemsthat were subjected to supergene oxidation, thereby permittingheap-leach treatment (eg Yanacocha, Pierina).To these preferred HS styles may be added the low-sulphidation veinor disseminated gold¦silver mineralisation that is commonplacealongside many HS systems (eg Victoria at Lepanto). * Originally published in the Proceedings of PACRIM æ99,published by The AusIMM.

Jan 1, 2000

By P Townsend, F Russell

Palabora Mining Company operates an integrated open pit mine, concentrator, smelter and refinery complex located in the Northern Province of South Africa. The Palabora open pit went into production in 1966, mining 30 000 t/d to produce some 62 000 tpa of copper. With continuous modification and improvement, a mining rate of 82 000 t/d, producing up to 135 000 tpa of refined copper, has been achieved. While these improvements have also enabled the mine life to be nearly doubled, the open pit will reach the end of its economic life by 2003. The Palabora orebody is vertical and the reserve extends to a depth of 1800 m over an area of 700 m by 200 m. Studies to assess the economics of mining the orebody by underground means began in the mid-1980s. These studies indicated that block caving is the lowest cost underground mining method that would generate a suitable return. In March 1996, a decision was made to develop a 30 000 t/d block cave mine that will extend the life of the Palabora Mining Company by a further 20 years. In terms of the relatively high rock strength and the resultant coarse fragmentation that is expected at the drawpoint, the Palabora cave can be considered rather unique when compared to other block cave operations. This paper describes the project in broad terms and details the mining method, particularly with respect to the cavability of the orebody and the design features to deal with the coarse fragmentation. The project commenced in July 1996 and final development of the undercut and drawbells is scheduled for completion in November 2003. This paper describes the status of the project and planning as of April 2000.

Jan 1, 2000

Permian ultramafic and associated rocks form a belt in East Nelson and contain widespread, but minor, chromite and copper mineralisation and some mining was carried out last century. Since mining ceased, about 1910, little mapping of the belt has been carried out although its origin has been debated vigorously. Recently it has been inferred to form part of a ophiolite sequence, which has been tectonically disrupted to form a melange, and several 'plate -tectonic' models have been proposed. Mapping in the central part of the belt has shown that mTlanges are to the east of the ophiolite sequence. Faulting is widespread so that in anyone section part of the sequence may be absent. Some of the faulting is difficult to recognise and probably took place during or soon after the sequence accumulated. Other faulting is clearly of Cenozoic age and includes major NNE striking faults, with large horizontal displacement, and approximately east-west striking faults with almost entirely vertical movement. The writer agrees that 'plate tectonics' could provide an acceptable explanation for the origin of the ophiolite sequence but the models so far proposed do not take into account the nature and field relationships of the rock units present. Copper Mineralisation is largely controlled by the younger faults, particularly those striking about north-east, and is largely confined to the western part of the ultramafic rocks particularly where slivers of the volcanics of the adjacent Lee River Group are enclosed. Mineralisation, along NNE striking shear zones, has recently been found in the volcanics some distance from the ultramafic rocks. The chromite mineralization is in the form of primary layering in the basal part of the ultramafic belt although in places it has been concentrated into lenses probably during serpentinisation.

Jan 1, 1977

Naturally occurring rutile contains approximately 96 per cent titanium dioxide (Ti02), whereas the product from the ilmenite reduction - aeration upgrading process, "sub- rutile", contains only about 92 per cent Ti02. Therefore, there is an-incentive to lift the quality of sub-rutile by removing transition metal impurities, in order to supply a more valuable and marketable product, particularly for the chloride-route pigment producers. Previous studies have shown that the sub- rutile residual iron content (of approximately 4 per cent) and residual manganese content (of approximately 1.5 per cent) are chemically bound within the titanium-oxygen mineral lattice, and are most difficult to remove by simple leaching methods. In attempts to improve their eventual removal, a simple process modification has been successfully investigated in laboratory scale trials. Transition metal sulphides have been formed in the reduced ilmenite by using a "sulphur-doping" technique during reduction (metallization) conducted at controlled temperatures. These compounds give rise to greatly enhanced dissolution of the unwanted transition metal constituents during the sub- sequent aeration and acid washing steps. Thus, the manganese content of the final sulphur- doped, reduced-aerated, acid washed product can be reduced by about 90 per cent to 0.2 per cent, and the iron content by about 70 per cent to less than 1.5 per cent, in comparison with those levels remaining after unmodified pro- cessing. Additions of sulphur as low as 2 per cent of the weight of the ilmenite have proven satisfactory. Preliminary studies reveal that the modified process is economically feasible. These results suggest that the sulphur content of the Collie coal char used in an unmodified reduction step must exert some influence on the eventual removal of iron and manganese during aeration and acid washing.

Jan 1, 1973

By T P. Hynes

Submarine tailings disposal is conceptually an attractive option for managing reactive mine wastes in coastal regions by virtue of reduced sulfide oxidation under a water cover and no infrastructure to maintain after mine closure. However, the lack of detailed knowledge of metal leaching, dispersal of fine tailings and biological impacts in the marine environment has led to no operating permits currently in effect in Canada. Detailed chemical and ecotoxicological assessments at two historic copper mine sites (Little Bay and Tilt Cove) in the north coast of Newfoundland with tailings disposed in an estuarine to shallow (=100 m) marine environment have demonstrated reduced reactivity of sulfidic tailings when submerged under water. Only non-acute toxicity is detected in biota inhabiting the immediate vicinity (A review of another historic shallow marine tailings operation in the southern tip of Vancouver Island (Jordon River) with a high-energy setting also reveals problems with unconfined tailings dispersal and temporal biological impacts. Documented studies at two deeper (140 - 360 m) marine tailings disposal operations at the northern tip of Vancouver Island (Island Copper) and northwestern coast of British Columbia (Kitsault) again illustrate imperfect predictions of tailings re-suspension and dispersal. At these sites, bioaccumulation of tailings-derived metals appears to be minimal. There is evidence of rapid re-colonisation of the tailings surface by benthos but of different species than the original population. Integrating these observations with reported metal fluxes and biological diversity associated with submarine hydrothermal vents, the risks and benefits of deep-sea (>1 km) tailings disposal are discussed. To determine if submarine tailings disposal in deep, confined basins on the seafloor is environmentally friendly, detailed multi-disciplinary research incorporating physical, chemical, biological and toxicological components will be indispensable.

Jan 1, 2003

The subject of octanes and knock in petrol engines is of general interest, not only to the engineers and chemists in the petroleum and automotive industries, but also to the motorist who wishes to see some light through the haze of propaganda regarding "super" petrols. A mixture of petrol vapour and air will explode when a spark is passed through it if it contains more than one and a half per cent. or less than six per cent. of petrol vapour by volume. In a petrol engine the mixture has to be within the explosive range before it will operate. When the spark is passed it 'ignites the petrol vapour-air mixture which burns with rapid but finite progress of the flame front 'through the unburnt gases in much the same manner that a charge of dynamite is consumed. The turbulence of the gases in the cylinder under normal operating conditions more than doubles the velocity of the flame front and enables the combustion to be completed by the end of the working (expansion) stroke:KNOCKIf the cylinder head 'is poorly designed or is covered with a deposit of carbon, it is possible for "hot spots" to develop, and these can ignite the mixture before the spark is passed. This pre-ignition gives rise to an engine knock but is accompanied by a dull thud rather than the ringing knock associated with the true "knocking" found in a petrol engine and attributed to the detonation of the mixture. Until a few years ago it was thought that this detonation was due to a shock wave produced by the rapid combustion of the mixture, and sufficiently intense to cause ignition of...

Jan 1, 1951

Vatukoula, the Fijian equivalent of gold rock, is the name of the community embracing the gold mines owned and operated by Emperor Gold Mining Company Ltd., Loloma (Fiji) Gold Mines, N.L., and' Dolphin Mines Ltd. It is situated in the Tavua Goldfields approximately five miles from the northern coast of Viti Levu, the largest island of the Colony of Fiji.The climate is sub-tropical, there being a definite wet and dry season. The wet season is somewhat variable in length but usually extends from December to March, during which time most of the rainfall for the year is recorded.Although the average annual rainfall is 71 in., more than twice this amount has been recorded. Precipitation at the rate of 5 in. per hour is not uncommon and 15 in. of rain has been registered in 24 hours. The mining methods adopted, therefore, had to suit these wet conditions.The occurrence of gold in the Tavua area has been known since 1872, but it was not until 1932 that discoveries were made which led to the formation of the present operating companies. In 1934 the Emperor Gold Mining Company Ltd. commenced operations, followed in 1935 by the Loloma (Fiji) Gold Mines, N.L., and later by the Fiji Mines Development Ltd., now known as the Dolphin Mines Ltd. Up to the end of 1951 these three mines had produced 2,501,688 tons of ore from which 1,277,881 oz. of fine gold and 347,429oz. of silver were obtained, realizing in Fijian currency £13,025,153.The three mines are situated close togeth.er on contiguous mining leases, and, although under common management, are operated as separate en,tities. Since 1944 all the...

Jan 1, 1953

By D M. Aranha, A R. Cabral

Theories on the origin of the Itabira iron formation (itabirite) in Quadrilßtero Ferrffero (QF), as elsewhere in the world, are restricted by the apparent lack of adjoining volcanic units, severe syndeformational metamorphism and deep weathering. Besides the three types of iron formations at QF (siliceous, dolomitic and amphibolitic; Dorr, 1969) we include a fourth type initially described as ocherous, goethitic, limonitic or even yellow iron formation. Considering its high magnetite content, it has been described as yellow magnetite itabirite (Pires, 1979). It was reported as formed by the alteration of the dolomitic itabirite (Dorr, 1969) although the anomalous Al2O3 contents are high for normal weathered itabirite. The yellowish magnetitic itabirite occurs at the bottom of the Itabira Iron formation, along the contact with the Batatal schists, and at the top units of the Itabira, within the Gandarela Formation. Within the magnetitic itabirite at the Tamanduß iron ore mine there are metric zones, concordant to the bedding of pillow-like structures, exhibiting a porous core, surrounded by an intermediate, more granular zone with numerous, minute rounded cavities grading to an external, fine-grained zone with much less minute cavities. In the external portions of some pillows a breadcrust type structure, derived by quenching with the water can be observed. In some other zones, such as the Barreiro hill, an outer, vesicular, whitish yellow, 5 - 10 mm thick, band grades to an aphanitic, isotropic band. The vesicles are slightly flattened against the band surfaces. The existence of fragmental layers showing flowage and fragment alignment, kaolinitic laminas and vesicles filled with kaolinite at Barreiro Hill and Capitpo do Mato Mine represent mesoscopic structures, indicators of a possible volcanic origin. Chemical compositions of the magnetitic itabirite from a wide area in QF revealed a relatively high Al2O3 content, consistent with a volcanic origin.

Jan 1, 2005

By D Thornton, B Smith, S Demey

Mine to Mill (MTM) optimisation, a total systems approach to the reduction of energy and cost in mining and mineral processing operations, is well-established technology. However, successful applications of MTM optimisation have been largely confined to gold, copper and lead/zinc semi autogenous grinding (SAG) operations, where the goals of tweaking the blast design to increase fines and hence throughput through the mill have been relatively easy to meet. The application of MTM optimisation in a more demanding environment, like that of a multi-stage crushing and screening aggregate operation, was conceived as part of a Department of Energy (DOE) initiative in 2004, aiming to reduce the energy consumption in the US aggregates industry. Two quarries operated by the Luck Stone Corporation of Richmond, Virginia, were selected for the demonstration sites. Dealing with ore variability and a requirement to maintain a fixed feed size distribution to the tertiary plant, whilst still aiming to increase yields of saleable products, presented some unique challenges. Despite these variables, the implementation of the MTM approach at Luck StoneÆs aggregate plant in Pittsboro, North Carolina, has led to a tangible improvement in productivity, particularly in the primary and secondary plants. The successful outcome was dependent upon several key factors, including reliable blasting and processing models, careful analysis of the rock conditions and plant configuration, understanding and buy-in from the Luck Stone operations staff, excellent collaboration with Virginia Tech staff and students, and long-term monitoring made possible through comprehensive PLC logging. This paper presents a review of the work conducted at the Pittsboro quarry and highlights the key reasons behind the successful implementation of the MTM approach in a complex plant environment.

Jan 1, 2007

A broad zone of intra-plate volcanism occurs for some 3000 km along the E. Australian coastal regions, extending from far northern Queensland southwards to Tasmania, westwards to western Victoria, and into southeastern South Australia. The age range, taken over the whole region, extends from Eocene to Holocene. Wellman & McDougall (1974) recognised the occurrence of three distinct types of volcanic occurrences: (a) Lava field provinces, dominantly basaltic and commonly strongly undersaturated, but of variable size. Large lava fields are especially exemplified by the younger provinces in northern Queensland (e.g. Nulla, McBride), and western Victoria. (b) Central volcano provinces, in which a reasonably well defined volcanic edifice is discernable. Such provinces are built of mildly undersaturated to saturated mafic lavas, but are also characterised by felsic volcanism (and often substantial mafic and felsic intrusive phases). Examples are the Springsure-Minerva Hills province, the Tweed and Focal Peak Shields (southeastern Queensland to northeastern N.S.W.), and the Nandewars, Warrumbungles, and Canobolas volcanic centres (N.S.W.). (c) A single leucitite province in N.S.W. Wellman and McDougall (1974) were able to show that the central volcano provinces exhibit a remarkably regular southward age migration pattern, the calculated migration rate being 66 + 5 mm yr , and these authors interpreted this in terms of the northward passage of the Australian plate across a fixed 'hotspot' within the upper mantle. The leucitite province also fits this migration pattern. The lava field provinces apparently exhibit more erratic regional age distribution patterns, but Sutherland (1981) has interpreted the data in terms of a multiple 'hotspot' model. It is noted, however, that the youngest areas of volcanism (Pleistocene 1. Department of Geology and Mineralogy, University of Queensland, St. Lucia, Brisbane, Queensland

Jan 1, 1987

The results expected from a longwall face can best be estimated from the ideal production rate, determined by the capacity of the equipment and the conditions in which it is installed, the effective operating hours, and the utilisation.The effective operating hours are determined by a number of scheduling factors which include the proportion of manned time to calendar time, the effective shift factor (effective time to manned time) and the move times.Analysis of the results achieved on the last 121 completed longwall panels in Australia (1984 onwards) shows a significant trend between 'actual tonnes/manned hour' and 'ideal production rate' (the measure of the capacity of the installation).Using 1982 'state of the art' longwall equipment, (the average in use in the seven year period), it should be possible to produce around 2.7M tonne/year ROM from a mine with one longwall. Few mines are achieving this.A review of production scheduling factors and general natural hazards affecting some mines suggests three things.1. Whilst some increase in average effective hours has followed the CIT decision, further improvement is possible at many installations.2. Many mines subject to general natural hazards, such as high gas make and high general stress, have found effective solutions and achieve the same utilisation as the overall average.3. A small number of faces within such mines have been severely affected, some less so. The most severe effects of natural hazards appear to be very site specific. This emphasises the need for detailed investigation of the causes, and development of means of predicting their presence. Only then can either satisfactory technical solutions be found to overcome the problems or prior decisions be chosen not to mine badly affected panels.

Jan 1, 1991

By T Goswami, M Edmondson

Henry Walker Eltin (HWE) are the mining contractors for Gloucester Coal at Stratford mine, which is in an environmentally sensitive area in the Avon Valley, NSW, Australia. Normal blasting at Stratford is done in a æstand upÆ or æbox cutÆ mode to suit the truck and shovel operations. Recently an opportunity of doing a throw blast became available when part of a ramp had to be blasted to accommodate changes to the pit design while not damaging the remainder of the ramp. The objective was to maximise throw into the void in order to minimise excavation costs by reducing the amount of overburden to be moved by the excavation fleet. It was necessary that the best result be achieved while staying within the vibration and airblast limits at a neighbouring property and nearby township. Both objectives were achieved through the application of OricaÆs knowledge of blast design, modelling and i-konTM electronic detonators. The i-kon system was used because of its known benefits in cast blasting and environmental control. The i-kon system provides the blaster with much greater accuracy, control and the flexibility to tailor blast designs. It has been found previously to enhance blast throw and provide cleaner high walls (Brent, 2002). The blast was a success, producing a muckpile with a high degree of looseness and consistent fragmentation, with an average throw to final spoil position of 37.5 per cent. This was achieved without any environmental exceedance. In addition, high speed filming showed that the coal edge had remained largely in place, indicating minimal coal loss. The results exceeded the expectations of HWE Stratford and the overall cost savings to HWE Stratford from this blast were recognised to be substantial. Further throw blasting opportunities at Stratford have been followed using the i-kon system to maximise benefits.

Jan 1, 2003

By F J. Rios

In the eastern high-strain domain of the Quadrilßtero Ferrffero, Brazil, hard and soft high-grade hematite ore may occur as schistose bodies in shear zones mainly related to the Cambotas-Fundpo thrust system. These orebodies are almost entirely constituted of oriented specularite platelets that develop both as a product of crystal-plastic deformation of hematite and solution-precipitation processes. Both mechanisms interact in the partitioning of the strain, while solution-precipitation is responsible for the precipitation of hematite and localised leaching of silica resulting in the formation of syntectonic ores. The analyses of fluid inclusions from specularite crystals of the Conceitpo and Timbopeba deposits, located in the northern and southernmost areas of the eastern high-strain domain of the Quadrilßtero Ferrffero, were studied using infrared microthermometry and Synchrotron x-ray fluorescence. The results indicate the participation of highly saline aqueous H2O-NaCl fluids containing other additional cations (Ca, Fe, K and probably Ti) in solution and homogenisation Temperature (Th) averaging between 130¦ - 190¦C. However, the partial fusion of metastable saturation phases indicates crystallisation temperatures of approximately 400¦C. The mineralisation process produces high-grade orebodies as well as Fe-rich specularitic itabirites that are explored in that area. The shear zones are related to thrust faults mapped and interpreted as related to the PanAfrican/Brasiliano Orogeny that affected the Quadrilßtero Ferrffero, thrusting the Paleoproterozoic platform sequence of the Minas Supergroup over Mesoproterozoic quartzites of the Espinhato Supergroup. They intersect and even overprint an early metamorphic and tectonic fabric of Paleoproterozoic age (Transamazonian Orogeny). The geological and fabric relationships lead to the conclusion that the fluids involved in the mineralisation were most probably of external origin, of still unknown source (possibly igneous), during the closure of the Spo Francisco Craton.

Jan 1, 2005