Search Documents

By S Grano, M Fordham, H Manouchehri, J Curral

This paper focuses on the impact of high pulp temperature on sphalerite flotation after the zinc regrind circuit in the Zinc Plant of Somincor, owned and operated by Lundin Mining Corporation. In the zinc circuit, the zinc rougher concentrate is reground with forged steel media before flotation with one stage of roughing and scavenging, and three stages of cleaning to obtain a zinc final concentrate (zinc grade >50 per cent). After regrinding, sphalerite flotation has been found to be seriously affected by high pulp temperature which may occur during the summer months. Mineral recoveries were found to be seriously reduced at pulp temperatures above 60¦C. At this high pulp temperature, neither elevated copper sulfate concentration nor a decreased pH alone appreciably increased Zn recovery. However, a combination of these two (eg a decrease in pH from 11.5 to 10.8, and an increase in copper sulfate dosage from 400 g/t to 800 g/t) was found to reduce Zn depression at high pulp temperature. At pulp temperatures below 45¦C, the negative influence of pulp temperature on mineral recoveries was minimal. A systematic series of flotation tests and solution/surface analyses were performed to reveal causes for poor sphalerite flotation at high pulp temperature after regrinding. The decrease in mineral recovery was shown to be associated with variations in the surface species on mineral particles in response to the increased pulp temperature. These variations in the surface species include collector desorption and superficial oxidation to form lead/zinc oxide/hydroxides on mineral particles. The influence of the type of regrinding media on sphalerite flotation at high pulp temperature was also addressed in this work.

Jan 1, 2008

Bauxitic laterite of variable thickness and grade is best developed in the Darling Range but covers a large part of the southwest corner of Western Australia. Its limits are defined by the rainfall isohyets to which jarrah forest is confined. Within this broad belt there is an increase in arable land southwards concomitant with a thinning of the laterite layer.Bauxite quality and perhaps thickness as well are dependent on the type of source rock, and are influenced by topography. Economic deposits occur over a vertical range in altitude of about 1200 ft. Some bauxite orebodies appear shoot-like in character, and analogy is suggested with the ore shoots of syngenetic metalliferous deposits.The alumina is in the form of gibbsite enabling low temperature digestion in treatment.INTRODUCTIONAlthough the existence of bauxite in Australia has been known for many years it is only recently that exploitation has commenced of the two most important deposits, strangely at almost diagonally opposite tips of the continent (Fig. 1).Recognition of the importance of the bauxite in the southwest corner came about initially through the efforts of Western Aluminium N.L. which, with some outside financial help, tackled the early exploration with commendable foresight and courage. Subsequent investigations around the periphery of the original reserves (now held by Alcoa of Australia) were undertaken by several companies, including Bauxite Exploration Pty. Ltd.ORIGIN OF BAUXITEThe genesis of bauxite is stilI somewhat controversial.Owing to its common association with kaolin some investigators have been led to believe that it has been derived from the latter; others believe the process has been vice versa.From a recent study of the Arkansas bauxite region in the...

Jan 1, 1964

The history of black coal as a fuel dates back in Europe more than 2,300 years, and possibly longer in China. Originally the mining of coal was done by underprivileged people, but with the industrial revolution and the dawn of mechanisation, the status of the coal miner improved. The improvement continued to the present day. Coal miners now take an important role in industrialised countries and enjoy a high standard of living. The miner is amongst the highest paid and best technologically served in any industrial activity. The abundance of coal relative to alternative fuels and its widespread occurrence, brings with it a prosperity much valued in those countries with significant resources such as Australia. Coal will play a major role in easing the world energy shortage. In addition to the conventional usage, throughout the world coal gasification plants are in various stages of development. Coal liquefaction plants are beyond the drawing board stage. Slurry pipelines to supply coal for direct burning in electric generating and other plants are planned. In the current atmosphere of environment consciousness, Australia has to contend with people with only marginal interest trying to influence coal mining activities to the detriment of the overall prosperity of Australia. Fortunately enlightened legislation is the greatest protector of the environment and in many instances great improvement to the environment ensues after mining has passed. With its vast resources of black coal Australia can look forward to a significant role in future supply of fuel. As a result of the trade and industry involved, Australia can become an even more influential country in world politics, trade, and the setting of high living standards.

Jan 1, 1975

The magnesite deposits near Young, N.S.W., occur in decomposed serpentine rock below a soil. and alluvial cover. They show considerable variation in both quality and depth which greatly hampers mining operations. Seismic refraction techniques afford methods of conducting detailed and reconnaissance surveys which yield a depth and velocity analysis of the serpentine/magnesite refractor. The measured seismic velocities may be used as an index of the presence and quality of the deposits. The Seismic Timer which was used in the test surveys is a simplified seismograph which makes use of seismic reciprocity by replacing the conventional seismic shotpoints with geophone stations and the conventional geophone stations with impact points of a sledge hammer. Thi,s enables the use of detailed seismic refraction techniques which yield the depth and velocity analysis of the refractor.INTRODUCTIONThe magnesite deposits near Young, N.S.W., were produced by a process of leaching and enrichment of magnesium in serpentine rock. The magnesite occurs in nodular form emplaced in decomposed rock at shallow depths below soil and alluvium. The depth ranges from close to the surface down to some tens of feet. The deposits are patchy and show considerable variation in both quality and depth, giving riseto considerable difficulties in mining operations.Due to the thorough leaching of the surface material, geochemical tests carried out so far have not proved satisfactory for locating the pockets of magnesite enrichment.It was decided to test the application of detailed shallow seismic refraction methods to the investigation of both the depth and quality of the deposits. The tests were carried out...

Jan 1, 1962

By Y Peng, D J. Bradshaw, X Chen

At NewcrestÆs Telfer gold mine, a strategy of regrinding pyrite rougher flotation concentrates has been proposed to increase gold recovery and reduce cyanide consumption in the CIL circuit. The regrinding will be followed by an additional copper/gold flotation stage, where copper minerals need to be separated from pyrite. However, although the minerals are well liberated, the separation of chalcopyrite from pyrite in the cleaner stage is not always straightforward. The surfaces of the fine particles, produced during regrinding, are more easily oxidised and contaminated than coarse particles, directly influencing the particle floatability. The depression of pyrite is difficult in the cleaner stage as well due to copper activation, a process which is also highly dependent on the grinding environment. In this study, different grinding media, including mild steel and stainless steel, was used in the regrinding to produce different regrinding chemistry, such as, pH, Eh, and iron hydroxide contamination. The effects of regrinding conditions on chalcopyrite flotation and its separation from pyrite were studied. It was found that the stainless steel grinding media, which produced an oxidising environment, was more beneficial for the separation of chalcopyrite from pyrite after regrinding. The mild steel grinding media had a detrimental effect on both chalcopyrite and pyrite flotation. This study addresses the importance of choosing suitable regrinding conditions in the pyrite and copper flotation circuit.CITATION:Chen, X, Peng, Y and Bradshaw, D J, 2012. Effect of regrinding conditions on the flotation of chalcopyrite and its separation from pyrite in the cleaner stage, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 279-286 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By K Williams

Marvel Loch South Pit has had a number of stages of open and underground mining activities before acquisition by Sons of Gwalia. The historical pit had achieved a completed pit depth of 150 metres and the shaft and decline mine had reached approximately 220 metres in depth using open stope mining methods. The various mining methods reflect the various economics and industry practice at the time. The South Pit ore zones are medium grade (~2.5 g/t) but have a regular geometry and large tonnes per vertical metre. A number of studies have been completed up to a pre-feasibility stage looking at options to extend the pit depth and to lower the unit cost of gold production. The options considered were the re-optimisation of the pit to determine further cutbacks or the innovative use of an in-the-wall ramp. The in-the-wall ramp (tunnel) would permit the removal of the in pit ramp to expose additional ore that was within the footprint of the ramp design and to provide the opportunity to increase the final pit depth. Similar mining method has only been used at Three Mile (Coolgardie, WA) and Chalice Mine (Norseman, WA). The tunnel would serve as a gateway for further extension of the south mine and the central ore zone via underground mining methods. The ultimate depth of the South Pit has been extended to 310 metres below surface and significant additional ore has been recovered. This paper will give an insight into the various studies to optimise the Tunnel mining method, the determination of the various tunnel dimensions, and the phases of mining to arrive at the completed design.

Jan 1, 2003

In south-eastern King Island, sediments and lavas of possible Upper Proterozoic to Lower Cambrian age have been intruded by Lower Carboniferous granitic rocks.Within the contact aureole of the Bold Head adamellite north of Grassy the sediments and lavas have been metamorphosed to hornblende hornfels facies grade. The thermal gradient within the contact aureole was small, as the hornfelses exhibit no mineral zoning over a distance of 700 ft from the adamellite.Skarns occur both within the adamellite near its contact with the country rocks, and within the country rocks as partial replacements of three dolomitic limestone horizons. The latter type, the exoskarns, commonly have an andradite-salite mineralogy and carry economic concentrations of scheelite. These resulted from the replacement of carbonate beds due to both diffusion and infiltration metasomatism. Silica, tungsten, minor sulphides, and water were introduced from the adamellite, while aluminium and iron diffused from the enclosing pelitic sediments. Calcium released during marble replacement countered the loss of iron and aluminium in the pelitic hornfelses transforming them to diopside-rich rocks.Endoskarns within the adamellite are the result of two way diffusion across the contact; calcium, aluminium, and iron diffused from sediment to adamellite as silica, potassium, sodium, and water diffused from adamellite to the sediments. From estimates of the lithostatic pressure and mole fraction of CO2, the mineral assemblages of the hornfelses imply that the temperature of metamorphism lay between 530° and 710°C. This temperature range is in good agreement with minimum temperatures, between 610° and 710°C, for the recrystallization of the marbles of the contact aureole, calculated from the determinations of the solid solution of the magnesite molecule in calcite.

Jan 1, 1971

Don Hausen was a pioneer in the field of quantitative mineralogy. Methodology that he developed at Newmont almost 40 years ago is still employed today, only the technology has advanced. Petrographic methods were stressed with an emphasis on alteration, mineralisation and paragenesis. Methodologies employed by Don on the Carlin deposit were applied to developing the Carlin Trend by helping to work out lithology and structure, which ultimately led to the discovery of deep high-grade deposits. Quantitative methods used by Don on San Manuel, Copper Creek and Superior, Arizona were applied to the development of the Batu Hijau Deposit in Indonesia. Advancements in technology since DonÆs time have made the mineralogist much more efficient. Manual measurement of peak heights off of strip charts for semiquantitative XRD has been replaced by software that does Rietveld refinement and whole pattern fitting. Hand contouring of XRD data has been replaced by digitised data incorporated into geologic models. Optical point counting, which would take a dayÆs work to process 1000 points, has been replaced by automated SEM methods where 20 000 points are possible in an hour. The use of the optical microscope remains relatively unchanged, and still remains as Don emphasised the æeyesÆ of mineral exploration. However, the information can be relayed much more quickly with digital image capture and electronic data transfer. Don insisted on becoming involved in projects at the grassroots level and supporting the project through mine closure. This made the mineralogist a liaison between exploration geologists, mine geologists, metallurgists and mine engineers. The methodology that Don helped develop continues to provide invaluable support to Newmont geologists and metallurgists worldwide today.

Jan 1, 2008

By R West

The Olympic Dam smelter facility processes copper concentrate feed using direct-to-blister smelting technology to support the current site production rate of 225 000 t/a copper. The metallurgical control of the Olympic Dam smelter is largely managed from a single central control room. Control room operation and management is therefore a key function in ensuring safe and reliable operation of the smelter, including identifying and initiating control of abnormal events. As part of a consolidated smelter reliability improvement program, a team consisting of process and control system engineers was formed. The teamÆs charter was to address and resolve the alarm flooding issues being faced by the control room technicians and the lack of an up-to-date base of supporting functional documentation. The project was successfully resourced with WorleyParsons metallurgists, Citect PLC technicians and the on-site technical team. Implementation was conducted over a 12 month period with the goal of achieving best practice alarm levels. The goal was achieved through a systematic process of alarm design review that analysed every configured alarm versus best practice design standards. Innovative concepts such as group-based alarms, first-up interlock displays, graphic only alarming, alarm help and alarm shelving were developed and implemented in conjunction with improved alarm masking. Total configured alarms were reduced from 20 000 to 5000 while the alarm rates were reduced from in excess of 200 alarms per hour per controlling technician to best practice levels of less than 12 alarms per hour per controlling technician. Completion of this program has provided a firm foundation for implementing further control optimisation and was a key activity in supporting sustained smelter reliability levels.

Jan 1, 2005

Peko Mines, a Division of Peko-Wallsend Operations Limited (PWOL) has operated several small underground mines in the Tennant Creek district of the Northern Territory supplying ore to a central treatment plant. The Argo Mine is the most recently developed by Peko Mines. A magnetic anomaly was identified from low level airborne magnetics in 1960 and drilling, which commenced on the site in 1969, was halted in 1974 and resumed in 1980 following the rise in the price of gold. By mid 1983 a resource of + 200 000 tonnes of 12 g/tonne Au had been outlined and a decision to develop the resource was taken following the drilling of three further diamond drill holes which did not significantly alter the value of the resource. The small size of the orebody could not support the full capital cost of two shafts and a single entry mine plan was developed to extract the ore at a rate of 15 000 tonnes per month and to provide all the safety features, ventilation systems and services of a two shaft mine. In December 1983 a contract was let to Allied Constructions Pty. Limited (Allied) to sink and equip a 4.8m shaft to a depth of 410m and to convert the headframe and winder, which are leased for the life of the mine by PWOL from Allied, from a sinking to a production configuration. Shaft equipment designed by Hardcastle & Richards Pty. Ltd. (H & R) in conjunction with PWOL includes a skip/cage, counter- weight, and an auxiliary cage on rope guides, a sealed ladderway and exhaust air ducts.

Jan 1, 1986

By M Titley, E Maidens

Many gold deposits were mineralised by fluids and processes that also altered the host rocks. This alteration may often be a useful visual aid that distinguishes barren, low-grade from high-grade regions in a rock mass. Alteration intensity is commonly used in gold deposits as a visual tool, along with face sampling or grade control support, to define oreblocks and guide excavation in underground and open pit mining. However, alteration is not often used at the resource estimation stage. Mineralised lodes are usually defined by geologists using a ægeo-grade envelopeÆ, where a number of constraints are considered, including an (arbitrary) cut-off grade; the ænaturalÆ grade break between high- and low-grades; and geological features including structural, lithological or alteration continuity. The geo-grade envelope is usually thought to satisfy the requirements of stationarity for grade estimation, and is considered a single domain. This paper examines a modelling technique combining gold grade and alteration, applied to the Wallaby deposit in Western Australia, to imbue a greater level of detail to the grade estimation in a region tested by relatively sparse drilling. This was achieved by utilising the correlation of gold grade and alteration, along with the spatial characteristics of the alteration, when estimating grades within a number of lodes. The alteration-driven estimation was utilised in conjunction with an unfolding approach, and the use of probability estimates, to overcome geometric data constraints. This technique allows greater control and most likely provides a more reliable estimate of the mineable resources than a global grade cut-off when visual control is to be a major vector in grade control.

Jan 1, 2003

The Northern Mariana archipelago in the W.Pacific forms a classic intra-oceanic island arc system far from the influences of continental crust. As such it offers an ideal location in which to study many of the problems of subduction-related volcanism. Radiogenic (Sr, Pb, Nd and Hf) and stable (0, S and H) isotope systems have been applied to the question of the possible involvement of components from the subducting slab in arc magmagenesis. The results contrast with earlier studies based upon limited sample suites and suggest that fluids, derived from the slab and enriched in mobile elements, substantially modify the composition of the mantle wedge and contribute to the characteristic geochemistry of arc magmas. Trace element data, including the occurrence of negative Ce-anomalies in the lavas seem consistent with this conclusion. Major and trace element variations within the arc lavas can be modelled in terms of crystal fractionation of a gabbroic mineral assemblage and mixing calculations indicate that this has the approximate composition of PLAG:CPX:MAG:OLIV = 60:25:10:5. This observation is compatible with the widespread occurrence of gabbroic nodules in lavas throughout the arc. Consideration of Rare Earth Element and phenocryst data leads to the conclusion that many of the more basic lavas may be the products of cumulus enrichment. The results of this study constitute a model for magmatic processes occurring in simple island arc systems, and may be generally applicable to other, more complex settings. The recognition of a return flux of material with 'continental' affinity to the mantle, via sediments on the subducting slab, also places strong constraints on geochemical models of crust-mantle evolution.

Jan 1, 1987

This paper presents an overview of the strategy adopted to bring the Ballymoney opencut lignite deposit to an advanced stage of mine design and confidence. Certain aspects of the project differentiate it from the normal Australian experience. These include the thick overlying glacial drift, the proximity to established infrastructure and the wide fluctua- tions in annual lignite demand. The incorporation of these factors in the mine plan are discussed. The deposit area is located near the town of Ballymoney, in Northern Ireland. In July 1986, after winning an internationally competitive tender, Meekatharra Minerals Ltd commenced an exploration programme designed to delineate reserves to supply a 450 MW power station. In less than eighteen months, a complete evaluation was undertaken and a price submitted in December 1987 to the relevant authorities for the supply of lignite. Subsequently, UK government consultants and significant inter- national banks have endorsed the findings. The mining study commenced with the evaluation of various develop- ment strategies, followed by selection of the most viable mining method and equipment. The equipment selected will mine four million tonnes of lignite and eleven million cubic metres of waste each year. In year 15, the waste removal requirement increases to almost seventeen million cubic metres. This results in an average strip ratio over the mine life of three cubic metres of waste per tonne of lignite. The quality of the product delivered to the run of mine conveyor transfer point, based on maximum resource recovery, will include heat content of 8813 kJ/kg (3789 Btu/Ib), ash content of 28% and moisture content of 40%.

Jan 1, 1989

By T C. McCuaig, D B. Mapleson

The Wannaway Deposit is a structurally modified komatiite-hosted nickel-sulfide deposit. Until recently, nickel sulfide accumulations surrounding the Widgiemooltha Dome had been studied with a focus on understanding volcanological aspects of komatiite flow regimes and nickel-sulfide accumulation. Although volcanological features can be observed at Wannaway they are overprinted by several generations of structures associated with multi-phase deformation of the Dome. On the mine scale, two significant deformational events can be distinguished that control ore distribution. The first deformational event is represented by the formation of a layer parallel foliation within the footwall metabasalt and boudinaging of the ore into two distinct orebodies (mega boudins) during a north-south compressional event. Evidence of a second compressional event (east-northeast-south-southwest) is defined by reverse > dextral thrust-folding of the ore zone. The latter deformational event focussed the sulfide ore into thrust front positions where folded ore sequences are mined with stope widths up to nine metres wide. Later stage compressional and extensional deformation phases are observed but have minor, localised effects on the geometry of the ore zone. Four orders of control on the geometry and distribution of ore are interpreted through a combination of primary and secondary features observed at Wannaway. Extending the structural aspects of the secondary overprint features into areas of potential mineralisation has not only defined targets for extensions to the Wannaway Deposit, but has also aided to delineate high grade mineralisation and aid mining decisions. Obtaining an understanding of the volcanological conditions of formation, and more importantly, the structural evolution of the Wannaway region has been an integral part in optimising production.

Jan 1, 2003

By G McSpadden

At September 2001 the beneficiation plant at BHP Billiton Iron OreÆs Mt Whaleback mine is set to treat 9.5 million tonnes per annum (Mtpa) of iron ore, 40 per cent better than original design. This paper describes the steps, decision-making processes and innovations used to increase capacity at minimum cost. The plant was designed in 1979 to operate at 1133 t/h for 6000 hours per annum, treating 6.8 Mtpa. Sufficient suitable contact ore was unavailable and feed was finer than planned. The plant was designed with minimum surge capacity between multiple process units. It had never reached design capacity. In 1993 a study by Fluor Daniel to treat increased tonnage resulted in modifications to improve plant operations. Efforts to expand production by increasing reliability did not achieve the desired capacity. NJ Morrow (Pty) Ltd (NJM) conducted a technical audit in 1996 with process evaluation by Mineral Processors. Replacement of operator interface and PLC logic in 1997 made plant operation and diagnosis easier. Involving operators in logic development enhanced their plant knowledge. Fluor Daniel Simulation developed a simulation model of the process. Mineral Processors and NJM reviewed the model findings, recommended metallurgical improvements and developed preliminary designs and costs. BHP Engineering produced a detailed design with a cost estimate of $A34 million. After analysis and revision of the design, a $A10.4 million upgrade to 8.5 Mtpa was carried out. Detailed modifications to the process units, particularly the HM drum plant, allowed significantly higher capacities and improved metallurgical performance. The target capacity was achieved in June 2001. Further modifications are progressing to treat lower-grade ores.

Jan 1, 2002

The Osborne copper-gold deposit (within the Trough Tank project area) is located in the Cloncurry Shire about 195 kilometres south-east of Mount Isa. It is hosted by Proterozoic metasediments of the Eastern succession of the Mount Isa Inlier. The deposit is overlain by 25-40 metres of Mesozoic cover, so it represents a true "blind target". Placer Exploration has 100% outright ownership of the property, having purchased the remaining 10% interest in the property from Shell in early 1993.Intensive exploration, both surface and via drilling at Osborne, has taken place since 1985, when CSR Limited Mineral Exploration and Development Group (acquired by Placer in 1988) entered into a joint venture with Billiton Minerals. Exploration effort from 1985 to June 1988 outlined a 20 kilometre strike length of magnetic horizons, in what was termed the North-East, Central and Southern anomalies, which were drilled with weak indications of copper-gold mineralization in the North-East anomaly. During the later half of 1989, four core holes were drilled into the shallower northern partofthe North-East anomalywhere previous drilling had outlined economic intersections of mineralization. These holes encountered high-grade copper-gold mineralization confirming the potential for an economic deposit to be hosted within the ironstone sequence. Further drilling involving over 400 holes (100 kilometres of drilling) has brought the deposit up to its present resource status.The current resource inventory is 36 million tonnes grading 2.0% copper and 1.0 grams pertonne gold and includes a high-grade zone of 13 million tonnes grading 3.6% copper and 1.5 grams per tonne gold. The discovery of this potential economic mineralization resulted from a persistent exploration effort based on indications that a large mineralizing system existed within a sequence of ironstones.

Jan 1, 1993

The æProfit Driver ModelÆ is a tool which builds costs from first principles and integrates revenue, costs and physical mining parameters and, hence, can quantify the impact and leverage on profit. In this paper an æexample mineÆ has been created to represent a typical Australian Open Cut Coal Mine. This has then been input into the Profit Driver Model to allow different variables to be tested. A series of variables were tested to determine which ones had the highest impact on profit and results are useful to management as a guide to the areas in which they can focus effort to achieve better profitability. Whilst the highest profit drivers are those external to the control of management and include selling price and exchange rate, the next most sensitive are those variables related to the geology of the mine and the mining method. These included coal quality, yield and strip ratio. Site management has some control of these. For example, the ability to vary the sequence of mining or improve the yield by a more efficient coal washing process. The efficiency of the workforce and management has similar impact to the mining variables. Finally, there are the supply variables, such as fuel, labour and explosives which are the least sensitive although, cumulatively, still significant. Each mine is different and the results of the example mine will not apply to all mines. However, the approach taken is universal and the tool illustrates a simple method to quantify the profit impact when changing variables. The benefit of the approach is the short time taken to get a set of results. This allows the more detailed and time consuming work to be more focused. The results illustrate that management has a significant influence on profitability.

Jan 1, 2000

A significant resource of uranium has been discovered within a buried palaeochannel located in the south western corner of the Officer Basin of Western Australia by PNC Exploration (Australia) Pty. Ltd. The mineral- isation is redox controlled and is hosted by Eocene organic rich paludal sediments. Prob- able insitu reserves are 13,000 t of contained uranium with an average ore grade of 0.12% at a cutoff grade of 0.03% U. The Mulga Rock palaeochannel has been traced for at least 100 km beneath the Quaternary surficial cover. The main channel is horseshoe shaped with the channel arms vary- ing from 5 to 15 km in width. The western arm connects to the Lake Raeside-Ponton Creek drainage system, whilst the eastern arm'is open to the south. The headwaters of the palaeo- channel are thought to have been the Lake Minigwal drainage system, prior to its capture by the Lake Rason system. Differential.erosion of the basement rocks during the Late Cretac- eous to Early Tertiary strongly influenced channel shape and resulted in the main channel being confined to a Permian,mudstone filled valley. Upwards of 100 m of fluviatile sediments accumulated within the palaeovalley during a period of subsidence in the Early Tertiary. Three broad stratigraphic units have been re- cognised within the channel: 1. An upper unit of fluviatile sands with interbedded lacustrine sediments, which have subsequently been wholly oxidised and variably silicified and ferruginised. 2. A middle unit of lacustrine to paludal sediments, which host the main mineral- isation. 3. A basal unit of fluviatile gravels and sand. The presence of excellently preserved Nothofagidites in organic rich paludal sediments from the middle unit, suggest that unit was laid down in a non-marine, fluviatile, humid environ- ment during the Middle Eocene.

Jan 1, 1988

Completion of a project requires two separate money-focused activities, namely economic evaluation of the cash flows underlying the project (before financing) and if the economics look promising, how it can be financed. Economic evaluation might be best led by a person with a technical-operating background, whereas financing might be best led by an accountant. Both should be presented in simple language with easy to understand models. Economic evaluation has a sad and bad history because it evolved from the fringes of accounting. Anyone can become a self-appointed practitioner. Some still take pride in mathematical complexity without realising that they distance themselves from the decision-makers and alienate other team members. Today there is no evaluation modelling consistency across the mining industry and this reflects poorly on our discipline. It is not tolerated amongst our peers in engineering and accounting. In 2009 æbest practiceÆ economic evaluation modelling is well defined. It is:easy to follow;tailored to its purpose;transparent;discipline, rigour and consistency;recording of all source data; and hencequick to audit. Mantra: If you cannot readily understand my model you do not have a problem, I do! The task of the economic model is to make the range of business cases underlying the decision easy to understand. Intellectual power is used to simplify the decision to its key issues and risks and to present the full range of possible business outcomes in readily understood terms. Project team members, management and the board must be able to make their decisions with æeyes wide openÆ. A steering committee should be established to develop a set of standards and practices that could be adopted for economic modelling within the industry. The industry needs to purge itself of the undisciplined economic evaluation modelling that now characterises the discipline.

Jan 1, 2009

By J J. Cilliers, E Ventura-Medina

Mineral froth flotation is used to separate particles of valuable mineral from its associated gangue. It involves the selective separation of the hydrophobic particles from the slurry into the froth. As air is blown into the slurry, the hydrophobic particles attach to the air bubbles, while the waste particles remain in suspension. While the froth rises up, bubbles start to coalesce and burst, allowing the entrained liquid surrounding the bubbles to drain and return part of the gangue to the pulp. Mineral separation is therefore a function of the amount of valuable material loaded on the bubble shells, as well as the amount of gangue material entrained in the liquid channels separating the bubbles (Plateau borders). As a result, the separation performance of the process is affected by mineral attachment and drainage or bursting in the froth. This study aims to establish the relationship between solids loading, froth stability and separation performance. For this purpose, a series of industrial experiments were carried out to measure mineral attachment as well as bubble bursting by combining direct sampling of the bubble films and video image analysis of the froth surface. This work suggests that the solids loading on bubbles strongly affects the separation performance. The results generally showed that solids loading and concentrate grade are closely related, while froth bursting rate can be linked to the drainage of gangue from the Plateau borders and also to the overall recovery of valuable mineral. It was shown in particular that higher loadings, usually associated with higher froth bursting rates, are indicative of more selectivity in attachment and therefore a higher mineral grade in the concentrate. Additionally, this work suggests that bubble solids loading and froth stability are essential parameters to include in froth flotation models as they allow control and optimisation of the flotation performance.

Jan 1, 2005