Search Documents

Airblast overpressure legislative limits can be extremely difficult to meet throughout Australia, which has by far the most stringent limits of any nation in the world. As the difficulty in meeting the limits is strongly dependent on the scale of mining, it is not surprising that the Australian coal mining industry is experiencing particular difficulties in meeting these limits. Eight full scale overburden blasts have been modelled with respect to overpressure impact for a strip coal mine, involving both dragline (cast) blasting and pre-strip (non-cast) blasting. Overpressure levels in the range 100 to 125 dBL have been measured at distances varying from 2.4 to 5.7 km, and modelling has successfully estimated both the amplitude and shape of overpressure waveforms to within an average of 1.2 dBL. Typical errors of prediction are around 0.6 dBL. This accuracy of prediction has been achieved by considering the impact of only the face holes, and the accuracy of prediction of both shape and amplitude suggests that it is these holes which dominate the environmental overpressure impact at distances in the range two to six kilometres, for cast and pre-strip blasting operations. Modelling has been based upon the Elemental Overpressure Wavelet proposed by Richards and Moore (2002), incorporating actual hole coordinates, actual delay timing, and assumed delay scatter statistics. The incorporation of delay scatter statistics has been particularly significant, and allows the determination of the range over which the peak overpressure levels are expected to vary. To date, modelling has considered only the use of conventional pyrotechnic delays, though simple adjustment to the scatter definition would allow estimation of overpressure levels, and their variability, with electronic delays.

Jan 1, 2004

IT is most remarkable and valuable property of mediurn and high carbon steels that they should be so susceptible to heat treatment, the wide range of variability in tenacity, ductility, etc, due to the normal influence of the carbon in the untreated material being enormously inereased thereby.The physical properties of steel and other metals are much more closely related to their structure than to their ultimate analysis.For instance, we may by chemical analysis determine the carbon content of a steel to be 0.5% ; but this information alone is insufficient to enable us to say what are the physical properties of the metal.Such a steel may possess 11 tensile strength of anything from 35 tons per sq. in., with much ductility, up to 80 tons per sq. in., with practically no ductility, according to its heat treatment. A microscopie examination, on the other hand, would show the structural composition of the steel, from which its physical properties could be approximately deduced. From this it will readily be understood that the microscope has played an important part in the development of modern rnetallurgy, and to-day it is in daily use for the examination of metals and alloys in the laboratories of most works dealing with the rnanufaeture and working of metals.THE IRON-IRON CARBIDE EQUILIBRIUMTo understand fully the mode of occurrcnce of the different constituents of a knowledge of the Iron-Iron Carbide equilibrium diagram (Fig. I) is essential to heat-treat steel successfully and to interpret microstructures correctly such a knowledge isabsolutely indispensable.A portion of the Iron-Iron Carbide Diagram, dealing with steels below 1000 and containing up to 1 carbon is given below.It should be noted that the diagram deals entirely with pure carbon steels, and does not indicate the influence of the usual so-ealled "impurities" present in all commereial carbon steels...

Jan 1, 1926

By R S. Suglo, G-K Er

Mineral processing is an essential component of a mine production chain and it accounts for significant proportion of the production cost. Over the past decade, significant research progress has been made in processing plant efficiency using theoretical, experimental and simulation modelling techniques. However, these studies are limited to process plant system as stand-alone units with no interactions with the mining units. In order to maximise the total mining system efficiency and more accurately simulate the system, the processing plant must be modelled as part of an integrated mining system. This becomes increasingly important in continuous surface mining systems, with limited ore processing capacity. In addition, plant efficiency is roughly estimated with known parameters or with simplistic statistical data, without regards to the stochastic processes governing these parameters, such as processing plant feed introduction. In this paper, a comprehensive model of the ore processing plant system is given and the object-oriented design (OOD) of the system is briefly introduced. The joint operation of ore processing plant system and haulage system is analysed. Numerical modelling is used to analyse the ore processing plant system under different conditions. Analysis of the results show that the optimum plant capacity is 0.7 tons/sec (2520 tons/hour). The results also show that the plant system resources cannot be fully utilised because the production rate is always less than the plant capacity. When plant capacity reaches an optimum value 0.7 tons/sec, the production rate is about 0.64 tons/sec. The underlying stochastic processes associated with plant and mine capacities cause this variability. In order to reduce this variability, there is the need to tightly set tolerances for the function variables.

Jan 1, 2003

By T Klinge, P Field, N Sugden, D Trenberth

Mining remains one of the key industries in Australia and many other countries with mineral wealth. In Australia, mining contributes 8.8 per cent to the countryÆs gross domestic product (McKay et al, 2000). In Queensland alone, mineral and petroleum industries contribute approximately $9.4 billion to the StatesÆ gross state product (2001/02) (Young, 2003). Increasing pressure on mining companies to perform in a global marketing environment requires mine management to consider more innovative ways to manage their resources û human, plant and equipment û which includes the gathering and analysis of operations data and information for improved decision making. For any mining operation utilising rubber tyred equipment such as trucks, front-end loaders and ancillary equipment, annual expenditure on tyres and related items can be significant. Even a small reduction in tyre operating costs can have a real effect on the business bottom line performance in the short term. Tyre Application Risk Management (TYREARMÖ) can provide substantial benefits in the long term across a number of KPIs not just through reduction in direct tyre expenditure but through flow-on improvements in safety, productivity and reduced environmental impacts. Several accidents involving tyres have also highlighted an increased need to consider the hazards and resultant risks arising from operations of rubber tyred mining fleets (Torlach and Johnston, 1990). This paper presents the process and results of achieving sustained safety and business improvement through the strategic alliance between an earthmover tyre management service provider, Klinge and Co (Klinge) and a BHP Billiton coal mine. The accompanying case study demonstrates in some detail the overall methodology, and the tools and technologies used where active management of data, its analysis and decisions taken have resulted in a 43 per cent improvement in tyre cost performance and a corresponding reduction in tyre-related downtime since the beginning of the alliance.

Jan 1, 2003

Petroleum exploration in the Australian arid zone has been proceeding at an ever-increasing pace, subject to financial fluctuations, since the 1960's. The impacts of petroleum exploration in the arid zone are less than they would be for corresponding operations in. e.g. a forest area: in this context, Australia is fortunate in that its major petroleum producing (and prospective) , basins are offshore or in the arid zone. In addition. the other major sources of impact in the Austrlian arid zone, namely pastoralism, tourism, and rabbits, tend to be concentrated around areas of particular conservation significance, whereas petroleum exploration is not. Despite this, the cumulative impacts of exploration are sufficient to have caused concern to government regulatory authorities and some sectors of the general public. Exploration is now subject to a range of environmental constraints with various degrees of legal enforceability. To enable exploration to continue without public opposition, the industry, and government agencies charged with regulating or supervising it, must demonstrate that the net benefits of exploration exceed net costs, including environmental costs. One particularly simple and cost-effective technique for increasing the net benefit/cost ratio of exploration is to reduce the net environmental costs by minimising and mitigating the impacts, both primary and secondary, of seismic acqisition. This is best achieved by a combination of preventive and restorative techniques: careful line positioning and low-impact (or zero) line clearance, coupled with simple rehabilitation of bladed lines. Line clearance without bulldozer blading - e.g. by rolling or simply pegging and trafficking, perhaps with tracked rather than rubber-tyred vibroseis - is one promising approach currently coming into use. Rehabilitation by grading soil banks ("windrows") back on to bladed tracks, though not yet in widespread use, has proved very successful in the limited areas where it has been applied to date.

Jan 1, 1987

By M Kilburn, A Edenton, M Adam, A Dehghan-Manshadi, R Smyth, L Lu

The blast furnace is a counter current reactor. The counter current principle of the furnace makes it very efficient in transferring the heat and mass required to drive the reduction reactions inside the furnace. However, this does impose a stringent requirement on the permeability of burden material in the furnace. Lump ore is one of the key ferrous feeds used in the blast furnace ironmaking process, often accounting for ten to 20 per cent of the blast furnace ferrous burden. As the lump ore descends through the blast furnace, it is dried, heated and reduced by the ascending hot reducing gas. To ensure good furnace permeability, generation of fines from burden materials including lump ore due to mechanical, thermal and chemical processes needs to be minimised. Unlike sinter and pellets, lump ore is subject to thermal degradation. To assess this behaviour of lump, the ISO decrepitation test (ISO 8371, 2007) is often conducted, and the result is calculated as a decrepitation index (DI). However, the DI values obtained from the existing ISO decrepitation test vary considerably between test portions and between laboratories, which makes meaningful comparison very difficult. In order to identify the sources responsible for the unacceptable repeatability, the effect of various testing conditions, such as particle size, heating rate, sample preparation and loading method, on the mean DI value was studied. The mechanisms contributing to thermal degradation in the top of the blast furnace and during the standardised decrepitation test are also discussed.CITATION:Lu, L, Kilburn, M, Dehghan-Manshadi, A, Adam, M, Edenton, A and Smyth, R, 2013. Thermal degradation of lump ore in the top shaft of blast furnaces, in Proceedings Iron Ore 2013 , pp 421-426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

The detailed work done by Stillwell and Edwards on the occurrence of cobaltite and safilorite-Iollingite at the South Mine, followed by its presentation as a paper to the Institute, calls for, a few notes on its occurrence elsewhere in the Broken Hill field. No massive cobaltite similar to that in the South Mine veinlet is known except from the Consols Mine (as mentioned in the paper). Fine grained cobaltite has, however, been found in low-grade ore from the North Mine. Microscopic grains occur in a mineralized green feldspar pegmatite. The feldspar has been replaced in part by graphite, and the cobaltite occurs in association with the graphite. In its hardness, pinkish-white colour, and resistance to the standard etchingqeagents it is similar to the South Mine cobaltite; it is etched by acid permanganate solution. An interesting feature of this occurrence is the way in- which some of the minerals (notably galena) have forced apart the graphite lamellae in crystallizing, forming lenses enclosed by the curved cleavage surlaces 0;[ the graphite.StillwelI and Edwards cite a note by G. Smitht for the statement that "cobaltite has been recorded from the Australian Broken Hill Consols Lode in the vicinity of the rich silver deposits, though not in contact with them."Smith, however, is here referring to the oxidized zone. Elsewhere in the same article he states "... a deposit of cobaltite in a very much altered condition was found. This was impregnated with silver, and assayed as high as 3,000 ounces," Of the cobaltite in the unoxidized zone, Smith simply states that it became rarer with depth.Cobaltite has also been recognized by Mr. H. F. Whitworth, M.SC., Curator of the Mining Museum, Sydney, in specimens from Burt's Copper Mine eight miles south of Broken Hill.

Jan 1, 1944

The primary object of this paper is to describe the present metallurgical practice of the Emperor Combined Mill, wherein ores from the adjoining and Associated Mining Companies, Emperor Gold Mining Company Ltd., Loloma (Fiji) Gold Mines, N.L., and Dolphin Mines, Ltd., are treated for the recovery of gold and silver.The mining field is located in the foothills, five miles from the sea, on the northern side of Viti Levu, the largest and most important island of the Fiji group.The orebodies occur in basalt and associated ash beds overlain by andesite, tuffs and sediments. The basalt is a dark greenish-black rock and in much of the ore mined is weathered with alteration of the olivine to serpentine and iron oxides, of the augite to chlorite and of the minute included crystals of iron ore to other iron oxides. Into the basalt intrudes a considerable number of andesite dykes, and the lodes occur as veins in these dykes, as "flatmakes" along fissures or, ash beds extending horizontally from the dykes and at the contact of the basalt and the andesite dices.The Emperor orebody is the largest and most important, and consists essentially of massive, shattered, well altered and mineralized basalt.Little or no free gold occurs in the ore at present being milled, the most important host minerals for gold being the tellurides sylvanite and hessite, next in importance being the sulphides, pyrite, marcasite and arsenopyrite. Chalcopyrite is present in quantities large enough to be troublesome in the subsequent concentrate treatment section, while sphalerite, tetrahedrite, bornite, galena and native tellurium are present in small quantities.Unimportant occurrences of native copper have been observed in both Dolphin and Emperor orebodies.

Jan 1, 1953

By Lawrie DC

Finely ground beryl was decomposed by mixing with ground limestone and soda ash andheating at 900¦C for,4-6, hours.The sintered material was then crushed and leached by boiling under reflux with 5N sulphuric acid for up to 4 hours. The liquor containing Be, ; Al, . Fe and, other elements as sulphates, was separated from the residue which consisted mainly of silica and gypsum, either' by filtration or by decantation washing.The clarified leach liquor.was first treated to remove Fed}: , by contacting with a primary amine-kerosene solution in2 counter-current stages. The iron free liquor wa,s then passed to a 4-stage counter-current extraction unit where it was con-tacted with 0.5M di-(2 ethyl hexyl), phosphoric acid (EHPA) in kerosene. The'operating conditions were such that at least 99 p'br cent of the Be and only 7' per' cent of the Al- was, extracted The ,B6`= and. Al were ;stripped from the organic phase by sod-ium hydroxide solution of suitable concentration to form soluble "beryllate" and "aluminate" respectively. Most of the Be was subsequently precipTitated a's Bo(OH)2 by-hoating the alkaline solution to 90C, the Al remaining in solution. After filtra-tion and washing, the Bo(OH)2 could be ignited directly to BeO at about 1000 C or used as a feed to further purification stages aimed at producing "nuclear grade" BeO.A small coaAter-current extraction unit was operated con-tinuously using liquor derived from the sintering and leaching stages. Data obtained in batch laboratory tests were confirmed. A product obtained by ignition of the washed "beryllate" precip-itate contained more than'99 per cent BeO.

Jan 1, 1963

By M Ljunggren, M Lundh

Dissolved air flotation (DAF) in wastewater treatment as a separation process of submillimetre biological flocs is based on the generation of bubble/floc aggregates. DAF is a complex process but has got advantages, such as allowing a high hydraulic load, compared to sedimentation. A thorough knowledge of the physics of the DAF process is, however, still lacking. This paper will present results of experimental studies on three aspects of significance to the separation process û the flow structure in the flotation tank, rise velocities of aggregates, influence of floc size on the separation efficiency. Flow structure. Measurements were performed in a pilot plant mapping and visualising the velocity field. The dispersion water (bubbles) had a decisive influence on the flow structure due to the effect of the bubbles on the bulk water density. Stratified conditions with a less dense, bubble-containing upper layer and a clear water, denser bottom layer were important for a good separation. A simple model of the stratified flow structure was elaborated making it possible to interpret the function of the aggregate rise velocities. Bubble/floc aggregates. The dynamics of single flocs, bubbles, aggregates were visualised using a borescope + CCD video camera + digital recorder + image analysis. Sequences of video frames made it possible to determine the rise velocities of the single aggregates. These velocities were found to be in the range 1 - 9 mm/s with a tendency for large flocs to have higher rise velocities. Separation versus floc size. The floc size distribution was measured in the DAF process. Data from three different DAF cases showed, that large flocs (> about 100 ¦m) were entirely separated, whereas small flocs experienced a less good separation. It was, moreover, found, that a very significant separation of flocs took place in the very upstream end of the separation zone in a pilot plant case.

Jan 1, 2005

By Crapp C. E

The Collinsville Coal Measures consist mainly of arenaceous sediments but indude eleven named coal seams. The Formation outcrops around the northern end of tbe Bowen Basin where it attains a thickness of 700 ft. in the Collinsville-Scottville area and overlies Lower Bowen Volcanies with angular unconformity. Most of the members in the Formation thicken basinwards. The regional dip is about 8 degrees. The Formation thins southwards and does not occur south of the Bowen River on the eastern flank. On the western flank it is represented by 60 ft. of barren sandstone at the limit of our mapping, 12 miles south of the Bowen River. Two seams are mined, the Bowen and the Blake; coal from the former produces high grade metallurgical coke, and the latter seam is mined for steaming coal. Where mined, the seams are about 20 ft. thick. The coals are of medium volatile bituminous rank and the lower coals are of higher rank than those above them.Reverse faults striking across the Coal Measures have been delineated and the existence of areas of intrusive rocks has been established. Intrusions rose up fault planes and, as felspar porphyry sills, selectively intruded coal seams, decimating reserves of coalavailable for mining. One sill, in the Blake Seam, attains a known thickness of 115 ft. Because the distribution and thickness of the sills is rarely predictable, density of drilling has been greater than in most coalfields.INTRODUCTIONThe assemblage of sediments occupying the northern portion of the Bowen Basin (Fig. 1) may be divided into four formations of Permian age:The Upper Coal Measures (U. Bowen)The Middle Bowen Marine Beds (M. Bowen)The Collinsville Coal Measures (M. Bowen)The Lower Bowen Volcanics (L. Bowen).Of these, the Upper Coal Measures and the Collinsville Coal Measures are known to contain coal seams of workable thickness.

Jan 1, 1960

Minerals and Metals Group (MMG) Century mine (Century) is a large open-cut mine in northwest Queensland approximately 2.5 km long, 1.5 km wide and 240 m deep, with an ultimate pit depth of 320 m. In 2009, the mine experienced three failures which began as small failures, and progressively developed into significant multi-batter failures. The incidents were managed by a combination of analysis, redesign and practical management to achieve positive outcomes for the mine. On the south wall of the mine, a series of batter-scale wedge failures occurred in December 2007. Analysis of structure orientations and design changes aimed to minimise the risk of failure extending over multiple batters, while accepting a risk of further small-scale failures. Design changes were constrained by a culturally sensitive area (CSA) located south of the wall. As mining progressed, shallow wedge failures developed over multiple batters and cracks were observed 60m back from the pit crest, indicating that a large-scale wedge failure was developing. Movement increased in January 2009 as a result of significant rainfall. After considering several design options, the area was stabilised by a cut-back of the wall. Two multi-batter failures also occurred on the north wall as mining progressed through a structurally complex area. Both north wall failures began as small failures that progressively developed, and required a redesign of the wall below as well as practical management of safety aspects. The complex structural geology was difficult to predict ahead of mining, and required geotechnical input into design changes as mining progressed. All three failures potentially had significant impact for ore recovery, and were managed by a combination of analysis, redesign and operational management have resulted to achieve positive outcomes in a challenging mining environment.

May 1, 2010

By S N CARRAS

Ore reserve estimation is a procedure involving data collection, data storage and judgement and assumptions about geology mining and metallurgy. Calculations are based on these assumptions and an economic analysis on projected cash flows is carried out. Ore reserve estimation must therefore be subjective and will always depend on the extent to which the assumptions used in arriving at the estimate are correct. This paper is an attempt to summarise the many aspects that can contribute to ore reserve problems and to offer some suggestions on how to minimise these problems. For further details on specific concepts readers are referred to the detailed descriptions in the referenced papers.

Jan 1, 1992

Mining of narrow vein mineralisation, invariably depending on the mining method selected, involves the extraction of both ore and waste rock. The level to which mining of waste rock can be minimised depends on numerous factors, but particularly the thickness and dip of the deposit. Resue mining is a method of mining that allows split face firing within stopes to allow waste and ore to be mined separately, allowing dilution to be minimised. This paper examines the technique of resue firing and its applicability to the mining of narrow vein deposits. Particular emphasis is placed on the conditions in which resue mining presents a suitable option for mining of narrow veins.

Jan 1, 2008

David Pollard will raise this matter in more aetail in a later paper, but mere are some obvious points that I wish to make. It is a relatively straightforward exercise to assess the competency at a low level in the workplace where the consequences of a worker's actions can be observed immediately. Assessing competency at higher levels which may involve creative, planning, design or supervisory functions is more difficult, especially where managerial responsibility and accountability for the output of others is involved. This is generally the case with the daily activities of most mining professionals, whether they be in operations, in a consulting capacity, in research, or in government.

Jan 1, 1994

By Toffeg A. N, Abdul-Hameed I

More than 1000 Ian of seismic reflection data correlated to ten exploration wells along with geological, gravity and magnetic data are used to construct the subsurface structure, in particular the crystalline basement, along a corridor approximately 100 Ian wide that traverses central Iraq in SE-NW direction for a distance of about 500 km from Baghdad in the central part of Iraq to Dohuk near the Turkish border. This transect is one of few such transects that represents the Iraqi contribution to the Global Geoscience Transects (GGT) project. The transect crosses two out of three major tectonic elements of Iraq: the unfolded zone and the folded zone.

Jan 1, 1990

The smaller mining company with full ownership of, or participation in, a mining project is generally unable to obtain funding as easily as the major mining house. While the equity market remains the main funding source for small projects, debt fund- ing options are becoming more available. Many international banks possess in-house mine fin- ancing expertise which can assist the smaller company in financing its share of project development. A clear understanding is necessary of both the benefits and limitations of bank funding, to ensure that all potential sources of funds are properly considered and integ- rated into the financial plans of the smaller mining companies.

Jan 1, 1984

Two recently published studies have considered whether and how robots, which have been designed for manufacturing applications, could find use in mining. The conclusions of both studies, if not identical, are compatible. Automation of mining activities will continue. Robots, at least in the short term, will have little application in mining. However, robotic concepts, both hardware and software, are of considerable relevance to mining automation, and can be anticipated to diffuse gradually into mine environments. The present paper is intended to convey the current state of thought on this subject to IFAC Symposium participants who may be unfamiliar with the referenced studies, and is not intended to report previously unpublished research.

Jan 1, 1985

By Troman L, Groutsch J. V

The Kwinana Nickel Refinery began operations in 1970 processing sulphide concentrates from Kambalda using the Sherritt Gordon pressure leach and hydrogen reduction process to produce nickel metal as powder and briquette. Over the years a number of changes have seen the refinery capacity increased from the original design capacity of 15 000 tpa nickel on an all concentrate feed to its current design capacity of 42 000 tpa nickel on an all matte feed. This paper outlines the changes in plant equipment and process for the most recent refinery expansion from 35 000 tpa to 42 000 tpa which have been implemented since 1992.

Jan 1, 1996

A universal grinding circuit model suitable for an arbitrary structure of flowsheet has been suggested. In this model classifiers and mills are described in a most general form. What puts the model in a class by itself is the automatic mass balancing in all streams of the circuit. In order to provide this a special classifier model is adopted. A previously published continuous steady state process model is used as a grinding model. Non-linearity of classifier model leads to a resultant circuit model which is equivalent to a non-linear integral equation. It complicates somewhat calculation algorithm in comparison to that of linear model, but provides a physically meaningful solution.

Jan 1, 1993