Search Documents

By Howell M. W

The purpose of this paper is to outline the main points in the construction of the various types of wire ropes more commonly used for winding in Australia; and the maintenance of the ropes, and cage and skip safety gear as practised at the South mine, Broken Hill.It should be mentioned that both of the shafts at present in use are dry, and both downcast with or without the assistance of the two exhaust fans normally in use: Night shift and week.-end overtime are practicaly non-existent.Thus, during night shift, the cages in No. 7 shaft are landed on the chairs at the surface, providing efficient covers for the· shaft, and allowing the maximum amount of rope to be wound on to the drums. This also applies to the cages of both No. 7 and No. 4 shafts during the week-ends.These factors, combined with electric winding and skip haulage, are calculated to obtain the best use of the ropes when properly attended.WINDING ROPES-TYPE AND CONSTRUCTIONThese ropes may be divided into four main types which will include the more commonly used constructions(a) One-size strand.(b) Warrington strand.(c) Flattened strand.(d) Locked coil.1. One-size strand as the name implies, is a rope the strands of which are constructed 9f wire of the one size.Usually the strands are of 7, 19 or 37 wires.

Jan 1, 1940

By Singh T, Singh D. P

India has limited resources of coking coal. Most of the coking coal seams are located in Jharia Coalfield. These seams were worked in the past by the bord and pillar system in a haphazard manner, which has resulted in honeycombs of old working. Most of such areas are under fire. In order to meet the demand of coking coal in the 21st century, it is essential that the coal locked due to old underground workings is recovered fully by conducting opencast mining to an ultimate depth of 500 m. The major problem envisaged in conducting opencast mining in such areas will be the stability of pit slopes over voids and the behaviour of subsided material in the pit slopes. An attempt has been made to simulate this complex situation from a specific section of the rockmass of a mine in an equivalent material (EM) model. The old workings existing in upper coal seam (V) were simulated by developing staggered bord and pillar workings in two sections and depillaring them. Opencast mining was conducted for recovery of coal locked due to irregular working in coal seam V. The slope instability caused by intersection of the slope with the void, during frontal working (by shovel-dumper combination) was observed in various situations. In this paper, the technique adopted for simulation of a 125 m thick section of rockmass in an EM model is outlined. Adverse effects of staggered workings and

Jan 1, 1988

Over the past 15 years many world-class gold discoveries have been made in the region. Some deposits, such as Lihir and Porgera in P.N.G., have a contained gold resource that places them among the top dozen deposits ever found on a worldwide basis. Can we see any pattern to these discoveries, or are they the result of good luck or chance by geologists and prospectors who struck it rich? Whilst such discoveries were a feature of the gold rushes of the 1850s and the 1900s, the present boom is now scientifically based. This paper develops an argument that long-tent, multi-disciplinary exploration by experienced geoscience teams underlie the successes achieved. Dis- coveries nearly always reflect a combination of skills, drawn from the areas of geology, geochemistry, geophysics and remote sensing, and a team approach. They do not represent the chance finds of a prospector's pick or such as the Norseman discovery where the gold reef was first noted by the prospector when his horse fell over the outcrop. The following deposits provide major examples of exploration successes within the Australian-Pacific region, it is not an exhaustive list and I have noted other significant producers at the end of this paper. For the Australian mines listed and based on our estimates for 1990 gold production, they represent about 20 per cent of the Australian production total.

Jan 1, 1991

By Whittaker B. N, Reddish D. J

This paper presents the physical modelling results of subsurface fracture development associated with Iongwall mining operations and an application of image processing techniques to interpretion of the results. Physical modelling results haióbeen obtained by employing a large sand and plaster model loaded purely by gravity as a means of fracturing the subsurface strata above the longwall excavation. The results have shown fracture development and crack propagation as a longwall face advances and demonstrated that the strength of stratified rocks, the presence and position of a weak band-, and the extraction thickness, have significant effects upon the overall fracture patterns above the excavation. Binary images of fracture patterns were scanned from the black and white photographs of the tested models using an image analyser coupled to a video camels. These images were manipulated by a custom written C program which allows the images to be processed in both vertical and horizontal direction. The images were filtered to quantitatively differentiate between vertical and horizontal fracture intensities. The vertical fracture intensity is particularly important as vertical fractures are considered to provide the main avenues for surface and subsurface water inflow into the excavation. The use of the image analysis techniques has shown a promising improvement in image enhancement and in model results interpretation in a quantitative manner. The numerical nature of the image analysis results will allow further statistical comparison with other modelling techniques to be undertaken and significantly increase the scope for use of the modelling technique results.

Jan 1, 1992

Mining engineering, metallurgy and minerals-related geology have proud traditions and are essential professions to support a safe and sustainable minerals industry. However, the future of these professions is under threat. The courses that produce such graduates are disappearing worldwide and the number of graduates available to enter the industry has been falling in English speaking countries for at least a decade. It is unlikely that this problem will be remedied by æsupply and demandÆ. Instead, some active intervention is required.

Jan 1, 2004

By F

Ore reserve estimation has been described as the most individualistic, the most prickly and even the most controversial of all the technical aspects of the mining profession. This symposium is a great opportunity to look at the present state of the art and full marks must go to the Sydney Branch for organi- sing it at this time. The first essential of good ore esti- mation is probably an awareness of the uncertainties involved, and the possible impli- cations of these uncertainties.

Jan 1, 1979

In the wake of the United Nations Conference on Environment and Development (UNCED) held in Rio de Janeiro in June 1992, evolved AGENDA 21. This document which was adopted at the Conference, provides a global action guideline for sustainable development into the 21st century.Sustainable mining requires a complete understanding of the `mineral cycle', including government legislation, mineral exploration, mining operations, rehabilitation, product use, re-cycling and waste disposal that takes into consideration associated social and environmental considerations and achieves economic objectives.

Jan 1, 1993

By Middlebrook PD

The problems of education and research in the extractive metallurgy area are being tackled by the University of Melbourne through activities centring on the Department of Chemical Engineering. The establishment of the G.K. Williams Laboratory and the enhance- ment of the teaching of material relevant to extractive metallurgy in the Chemical Engineering course aim-at providing graduates and experienced researchers for the industry and at providing a strong research group carrying out industrially significant research in the area of pyrometallurgy.

Jan 1, 1986

By Hamilton LH, Campbell PB

Since fundamental research in applied coal petrography is carried out mostly on polished surfaces, backscattered electron microscopy is most applicable for studying coal in the SEM. By employing this technique coal macerals can be easily identified , and information on the relations between maceral groups, mineral matter and trace elements are highlighted by grey level contrasts. This type of information is valuable in coal technology and cannot by normally revealed by the light microscopy (e.g. the distribution of inherent mineral matter).

Jan 1, 1989

About 11,000 tons of contaminated zinc flotation concentrate were available in the form of earth walls from dams used for atmospheric drying of the concentrate.Following successful laboratory tests this material was treated in a plant by crushing, grinding, and then flotation in a circuit consisting of roughing, scavenging, and two stages of cleaning. Reagents used were copper sulphate and a little butyl xanthate and frother. About 5,720 tons of zinc concentrate assaying 52· 3 per cent zinc were produced.

Jan 1, 1968

By Tilyard P. A

Pasminco has tested a Valmet ES1 ceramic disc vacuum filter at its Broken Hill concentrators. On lead and, particularly, zinc concentrates at the ZC Mine the filter performed well but on North Mine lead concentrate problems were experienced with deposition on the disc, which resisted both ultrasonic and acid cleaning. A preliminary financial analysis showed that the application of the filter at the ZC concentrator was worth pursuing. Accordingly an ES30 machine has been hired for plant evaluation.

Jan 1, 1989

By H Jha, M C. Thomas, P Gupta, S K. Sit

The modern jig with a state-of-the-art control system is much more effective than its older version. This improved control system is used to modulate the amplitude and the frequency of the jig cycle. These two prime parameters are optimised with respect to feed characteristics for best jigging performance. Based on this understanding any jigging plant can be optimised. In addition to these established facts present study shows process efficiency improves further through optimisation of the feed quality.

Jan 1, 2007

The BHP Steel Group embarked on a Total Quality Control (TQC) programme in 1984 in response to enquiries from a major customer regarding procedures for quality in materials supply.The TQC initiative has been adopted by all seven Divisions of the Steel Group and covers a broad and comprehensive range of management and workforce improvement initiatives.The development of the TQC initiative in the Collieries Division of BHP Steel over the past eighteen months has resulted in important experiences and leanings.

Jan 1, 1991

By Champigny N, Grimley P. H

To a bank that granted his request for a loan, the late American humorist Robert Benchley responded, `I don't trust a bank that would lend money to such a poor risk'. This quotation is unlikely to be the norm among mining companies that secure project financing. However, a poor appreciation of one of the key risks of a mining project, the reserves, often results in disastrous financial consequences. This conclusion is the subject of the discussion and analyses presented in this paper.

Jan 1, 1994

The Plant Control and Data Logging System for the Loy Yang Open Cut (LYOC) is part of a control and communications network designed to provide a high level of surveillance of open cut plant and facilitate the efficient co- ordination of operations and plant maintenance. The computer system selected utilises a central dual mini-computer and multiple microcomputer data transmission network ,linked to the plant controllers using distributed, microcomputer based remote data collectors or outstations. Several aspects of the computer system are outlined.

Jan 1, 1982

The valuation of resources companies is open to a huge amount of subjectivity. Not only are valuations subject to fast changing assumptions, such as commodity prices, exchange rates, ore grades, etc., but there is also no common agreement on the methodology to be used. To borrow from Malcolm Fraser, life wasn't meant to be easy for the resource company valuer. I will demonstrate three recent examples of valuations carried out but where the market or actual transactions done show very different results.

Jan 1, 1989

By W F. Bawden, J T. Paynter

This investigation involves laboratory testing and stability analysis of paste fill at the Golden Giant Mine. Site-cast samples are tested in unconfined, confined, and consolidated-undrained triaxial compression. Pore pressures during shear and consolidation characteristics are measured to determine both drained and undrained shear strength parameters and assess the potential for undrained loading. Liquefaction potential is also considered. A limit equilibrium solution is used to obtain factors of safety against failure of the fill during mining of adjacent stopes.

Jan 1, 1998

The cost of constantly extending a decline tunnel that plays a part in the actual extractive process is a revenue cost. The characteristics of such a decline tunnel are that it is dug in a series of relatively small excavations. It follows the ore body and is dug as close to the ore body as practicable. In addition, the decline allows for the extraction of ore in the immediate vicinity, with the ore being extracted in a relatively short period of time.

Jan 1, 1990

Progress on this project will be verbally reported and a description given of the main features. A detailed feasibility study was completed in December 1986, and the Joint Venture has issued an Environmental Impact Statement. This was open for public comment until 16 February. Issues presently being considered include economic justification traffic, air quality, noise, marine fauna and flora, visual impact, heritage and construction impact. Detail design and construction is likely to commence in mid 1987, following determination of the above matters.

Jan 1, 1987

By Singleton T

Increasing world competition puts pressure on sales volumes and prices. This in turn reduces potential profit margins. This in turn increases the focus on costs.Increasing demands on quality and service puts pressure on delivery performance - the right product at the right time. This in turn reduces the scope for errors and delays - and this in turn increases focus on equipment reliability. In the mining industry, both costs and equipment reliability have one significant thing in common - they are driven substantially by maintenance.

Jan 1, 1998